For a5xx the gpu is 64b so we need to change iova to 64b everywhere. On
the display side, iova is still 32b so it can ignore the upper bits.
(Although all the armv8 devices have an iommu that can map 64b pa to 32b
iova.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
We can have various combinations of 64b and 32b address space, ie. 64b
CPU but 32b display and gpu, or 64b CPU and GPU but 32b display. So
best to decouple the device iova's from mmap offset.
Signed-off-by: Rob Clark <robdclark@gmail.com>
With the new device hierarchy for MDP5, we need to enable runtime PM
for both the toplevel MDSS device and the MDP5 device itself. Enable
runtime PM for the new devices.
Since MDP4 and MDP5 now have different places where runtime PM is
enabled, remove the previous pm_runtime_enable/disable calls, and
squash them in the respective kms drivers.
The new device hierarchy (as expressed in the DT bindings) has the GDSC
tied only to the MDSS wrapper device. This GDSC needs to be enabled for
accessing any register in the MDSS sub-blocks. Once every driver is
runtime adapted, the GDSC will be enabled when any sub-block device
calls runtime_get because of the parent-child relationship with MDSS.
Until then, we call pm_runtime_get_sync() once for the MDSS device to
ensure the GDSC is never disabled. This will be removed once all the
drivers are runtime PM adapted.
The error handling paths become a bit tricky when we call these runtime
PM funcs. There doesn't seem to be any helper that checks if runtime PM
is enabled already. Add bool variables in mdp4_kms/mdp5_kms structs to
check if the driver had managed to call pm_runtime_enable before bailing
out.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The MDP4 driver tries to request and set voltages for regulators required
by the DSI PLLs.
Firstly, the MDP4 driver shouldn't manage the DSI regulators, this should
be handled in the DSI driver. Secondly, it shouldn't try to set a fixed
voltage for regulators. Voltage constraints should be specified on the
regulator via DT and managed by the regulator core.
Remove all the DSI PLL regulator related code from the MDP4 driver. It's
managed in the DSI driver for MSM8960/APQ8064 already.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
attach_dev gets called in mdp4_kms_init, but there is no corresponding
detach_dev called in the error path or in the kms driver unload path.
Detach and destroy mmu in mdp4_destroy.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
They only complete the page flip events to avoid oops when the drm
file closes. The core takes care of that now and we can remove this
code.
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-8-git-send-email-daniel.vetter@ffwll.ch
WARN_ON() takes a condition rather than a format string. This patch
converted WARN_ON() to WARN() instead.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an mdp4 incoder for DSI. Only DSI video mode is supported as of
now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinay Simha BN <vinaysimha@inforcecomputing.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently, the driver defers if it doesn't find a drm_panel. This forces
us to have a drm_panel, if not, the driver isn't usable.
Make the lcdc encoder initialization independent of the availability of
the drm panel. We only check if there is a panel node specified in DT. If
it isn't, then we don't initialize the encoder at all. The panel node is
passed to the lcdc encoder and lvds connector drivers.
The connector driver takes the responsibility to retrieve the drm_panel
from the panel node, and update the status on whether the panel is
connected or not. This makes the panel usable even if the drm_panel
driver is inserted as a module later on.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pending interrupt status needs to be cleared before enable the
interrupt. Otherwise it's possible to get a pending interrupt instead
of an incoming interrupt.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP planes can be implemented using different type of HW pipes,
RGB/VIG/DMA pipes for MDP5 and RGB/VG/DMA pipes for MDP4. Each type
of pipe has different HW capabilities such as scaling, color space
conversion, decimation... Add a variable in plane data structure
to specify the difference of each plane which comes from mdp5_cfg data
and use it to differenciate the plane operation.
V1: Initial change
V2: Fix a typo in mdp4_kms.h
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was a hold-over from the pre-atomic days and legacy userspace that
only understood CRTCs. Fortunately we don't have any properties, so
this doesn't change anything. But before we start growing some plane
properties, we should fix this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP FLUSH registers could indicate if the previous flush updates
has taken effect at vsync boundary. Making use of this H/W feature
can catch the vsync that happened between CRTC atomic_flush and
*_wait_for_vblanks, to avoid unnecessary wait.
This change allows kms CRTCs to use their own *_wait_for_commit_done
functions to wait for FLUSH register cleared at vsync, before commit
completion.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A few spots in the driver have support for downstream android
CONFIG_MSM_BUS_SCALING. This is mainly to simplify backporting the
driver for various devices which do not have sufficient upstream
kernel support. But the intentionally dead code seems to cause
some confusion. Rename the #define to make this more clear.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Both MDP4 and MDP5 share some code as far as YUV support is
concerned. This change adds this information and will be followed
by the actual MDP4 and MDP5 YUV support patches.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
On mdp4 there is a single global LAYERMIXER_IN_CFG register. The
previous logic to share that between multiple crtcs didn't actually
handle plane-disable very well. Easier just to look at all of the
crtcs each time.
Signed-off-by: Rob Clark <robdclark@gmail.com>
LVDS panel support uses the LCDC (parallel) encoder. Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector. Nor is there is anything re-used with mdp5.
Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().
The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In particular, blend_setup() should not overwrite the other crtc's mixer
settings. Also, the encoder needs to be able to specify the mixer-id
explicitly, since both LVDS and DTV use 'INTF_LVDC_DTV', so we cannot
guess the mixer-id from the interface.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel holds this clk via a fake-parent relationship.
Upstream clock framework requires that we hold it explicitly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The hw cursor is relatively adept at triggering underflows, which
manifest as a "blue flash" (since blue is configured as the underflow
color). Juggle a few things around to tighten up the timing for setting
cursor registers in DONE irq.
And most importantly, don't ever disable the hw cursor. Instead flip it
to a blank/empty cursor. This seems far more reliable, as even simply
clearing the cursor-enable bit (with no other updates in previous/
following frames) can in some cases cause underflow.
v1: original
v2: add missing locking spotted by Micah
Cc: Micah Richert <richert@braincorporation.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This can be shared between mdp4 and mdp5. Both use the same set of
parameters to describe the format to the hw.
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are some little bits and pieces that mdp4 and mdp5 can share, so
move things around so that we can have both in a common parent
directory.
Signed-off-by: Rob Clark <robdclark@gmail.com>
