Renamed __orr32 and __bic32 function names to more descriptive
dwc2_set_bit and dwc2_clear_bit respectively.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only unmasked endpoints based on DAINTMSK register.
This will allow to minimize GINTSTS_GOUTNAKEFF interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 'for' loop skipped masked and non-ISOC EPs. Also breaked 'for' loop
after setting SGOUTNAK in DCTL,when one enabled EP was detected.
This will allow to minimize incomplete ISOC OUT interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabled only that ISOC endpoints,for which interrupt bit was set
in the DAINTMSK register. This will allow to minimize incomplete
ISOC IN interrupt handling.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed AHB burst size from INCR4 to INCR by default.
With this value driver shows excellent DMA performance.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc2_hsotg_core_init_disconnected() function used AHB burst size
parameter, instead of calculating already calculated value.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Razmik Karapetyan <razmik@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move dwc2_hsotg_wait_bit_set function to core.c so it can be used
anywhere in the code.
Added dwc2_hsotg_wait_bit_clear function in core.c.
Replace all the parts of register bit polling code with
dwc2_hsotg_wait_bit_set or dwc2_hsotg_wait_bit_clear functions
calls depends on code logic.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Only check the ID portion of the GSNPSID register and don’t check
the version. This will allow the driver to work with version 4.00a
and later of the DWC_hsotg IP.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some UDC drivers (like the DWC3) expect that the response to a setup()
request is queued from within the setup function itself so that it is
available as soon as setup() has completed.
Upon receiving a setup request the function fs driver creates an event that
is made available to userspace. And only once userspace has acknowledged
that event the response to the setup request is queued.
So it violates the requirement of those UDC drivers and random failures can
be observed. This is basically a race condition and if userspace is able to
read the event and queue the response fast enough all is good. But if it is
not, for example because other processes are currently scheduled to run,
the USB host that sent the setup request will observe an error.
To avoid this the gadget framework provides the USB_GADGET_DELAYED_STATUS
return code. If a setup() callback returns this value the UDC driver is
aware that response is not yet available and can uses the appropriate
methods to handle this case.
Since in the case of function fs the response will never be available when
the setup() function returns make sure that this status code is used.
This fixed random occasional failures that were previously observed on a
DWC3 based system under high system load.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using a AIO read() operation on the function FS gadget driver a URB is
submitted asynchronously and on URB completion the received data is copied
to the userspace buffer associated with the read operation.
This is done from a kernel worker thread invoking copy_to_user() (through
copy_to_iter()). And while the user space process memory is made available
to the kernel thread using use_mm(), some architecture require in addition
to this that the operation runs with USER_DS set. Otherwise the userspace
memory access will fail.
For example on ARM64 with Privileged Access Never (PAN) and User Access
Override (UAO) enabled the following crash occurs.
Internal error: Accessing user space memory with fs=KERNEL_DS: 9600004f [#1] SMP
Modules linked in:
CPU: 2 PID: 1636 Comm: kworker/2:1 Not tainted 4.9.0-04081-g8ab2dfb-dirty #487
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
Workqueue: events ffs_user_copy_worker
task: ffffffc87afc8080 task.stack: ffffffc87a00c000
PC is at __arch_copy_to_user+0x190/0x220
LR is at copy_to_iter+0x78/0x3c8
[...]
[<ffffff800847b790>] __arch_copy_to_user+0x190/0x220
[<ffffff80086f25d8>] ffs_user_copy_worker+0x70/0x130
[<ffffff80080b8c64>] process_one_work+0x1dc/0x460
[<ffffff80080b8f38>] worker_thread+0x50/0x4b0
[<ffffff80080bf5a0>] kthread+0xd8/0xf0
[<ffffff8008083680>] ret_from_fork+0x10/0x50
Address this by placing a set_fs(USER_DS) before of the copy operation
and revert it again once the copy operation has finished.
This patch is analogous to commit d7ffde35e3 ("vhost: use USER_DS in
vhost_worker thread") which addresses the same underlying issue.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Increase max_speed of the mass_storage driver for UDCs that support
SuperSpeed Plus. The composite driver will pass this value to UDC core
to set the device speed on probe (actual speed may be different
depending on whether the USB controller supports it or other external
factors).
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When the host wants to fetch OS descriptors, it sends two requests. The
first is only for the header and the second for the full amount
specified by the header in the first request. The OS descriptor handling
code is distinguishing the header-only requests based on the wLength of
the setup packet, but the same code is executed in both cases to
construct the actual header. Simplify this by always constructing the
header and then filling out the rest of the request if the wLength is
greater than the size of the header.
Also remove the duplicate code for queueing the request to ep0 by adding
a goto label.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handling an OS descriptor request, one of the first operations is
to zero out the request buffer using the wLength from the setup packet.
There is no bounds checking, so a wLength > 4096 would clobber memory
adjacent to the request buffer. Fix this by taking the min of wLength
and the request buffer length prior to the memset. While at it, define
the buffer length in a header file so that magic numbers don't appear
throughout the code.
When returning data to the host, the data length should be the min of
the wLength and the valid data we have to return. Currently we are
returning wLength, thus requests for a wLength greater than the amount
of data in the OS descriptor buffer would return invalid (albeit zero'd)
data following the valid descriptor data. Fix this by counting the
number of bytes when constructing the data and using this when
determining the length of the request.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The irq is available in hsotg already, so there's no need to pass it as
separate function parameter.
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As devm_ioremap_resource() checks for valid resource,
make use of it instead of testing ourselves. As a bonus
memory region is requested.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pointer tv_nexus is being initialized a value and this is never read
and is later being updated with the same value. Remove the redundant
initialization so that the assignment to tv_nexus is performed later
and more local to when it is being read.
Cleans up clang warning:
drivers/usb/gadget/function/f_tcm.c:1097:25: warning: Value stored to
'tv_nexus' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The local variable event is of type enum usb_phy_events. Use
the same enum value USB_EVENT_NONE instead of UX500_MUSB_NONE.
This avoids a warning when building with clang:
drivers/usb/phy/phy-ab8500-usb.c:906:30: warning: implicit conversion from
enumeration type 'enum ux500_musb_vbus_id_status' to different enumeration
type 'enum usb_phy_events' [-Wenum-conversion]
enum usb_phy_events event = UX500_MUSB_NONE;
~~~~~ ^~~~~~~~~~~~~~~
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
mxs_charger_secondary_detection() is only used in this file, so make
it static.
This fixes the following sparse warning:
drivers/usb/phy/phy-mxs-usb.c:581:23: warning: symbol 'mxs_charger_secondary_detection' was not declared. Should it be static?
Acked-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use dma_pool_zalloc instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in the
USB stack for reported issues. Mostly gadget driver fixes, although the
typical set of xhci bugfixes are there, along with some new quirks
additions as well.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWo613g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymS1QCcCDbBPEJQAKF64SyHWZfebeFIBpMAnR9vku/h
1YXAXpcAJE5lGVVva3+I
=57Qr
-----END PGP SIGNATURE-----
Merge tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in
the USB stack for reported issues. Mostly gadget driver fixes,
although the typical set of xhci bugfixes are there, along with some
new quirks additions as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
Revert "usb: musb: host: don't start next rx urb if current one failed"
usb: musb: fix enumeration after resume
usb: cdc_acm: prevent race at write to acm while system resumes
Add delay-init quirk for Corsair K70 RGB keyboards
usb: ohci: Proper handling of ed_rm_list to handle race condition between usb_kill_urb() and finish_unlinks()
usb: host: ehci: always enable interrupt for qtd completion at test mode
usb: ldusb: add PIDs for new CASSY devices supported by this driver
usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path
usb: host: ehci: use correct device pointer for dma ops
usbip: keep usbip_device sockfd state in sync with tcp_socket
ohci-hcd: Fix race condition caused by ohci_urb_enqueue() and io_watchdog_func()
USB: serial: option: Add support for Quectel EP06
xhci: fix xhci debugfs errors in xhci_stop
xhci: xhci debugfs device nodes weren't removed after device plugged out
xhci: Fix xhci debugfs devices node disappearance after hibernation
xhci: Fix NULL pointer in xhci debugfs
xhci: Don't print a warning when setting link state for disabled ports
xhci: workaround for AMD Promontory disabled ports wakeup
usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()
...
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87c ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of fixes for current -rc cycle. Most of the changes are on
dwc3 this time around (59%) with some function changes (25%).
Out of the those, the most important fixes are:
- EP0 TRB counter fix on dwc3
- dwc3-omap stopped missing events during suspend/resume
- maxpacket size fix for ep0 in dwc3
- Descriptor processing fix for functionfs
Apart from these, your usual set of important-but-not-so-critical
fixes all over the place.
-----BEGIN PGP SIGNATURE-----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=eRDf
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.16-rc2
First set of fixes for current -rc cycle. Most of the changes are on
dwc3 this time around (59%) with some function changes (25%).
Out of the those, the most important fixes are:
- EP0 TRB counter fix on dwc3
- dwc3-omap stopped missing events during suspend/resume
- maxpacket size fix for ep0 in dwc3
- Descriptor processing fix for functionfs
Apart from these, your usual set of important-but-not-so-critical
fixes all over the place.
ACM driver may accept data to transmit while system is not fully
resumed. In this case ACM driver buffers data and prepare URBs
on usb anchor list.
There is a little chance that two tasks put a char and initiate
acm_tty_flush_chars(). In such a case, driver will put one URB
twice on usb anchor list.
This patch also reset length of data before resue of a buffer.
This not only prevent sending rubbish, but also lower risc of race.
Without this patch we hit following kernel panic in one of our
stabilty/stress tests.
[ 46.884442] *list_add double add*: new=ffff9b2ab7289330, prev=ffff9b2ab7289330, next=ffff9b2ab81e28e0.
[ 46.884476] Modules linked in: hci_uart btbcm bluetooth rfkill_gpio igb_avb(O) cfg80211 snd_soc_sst_bxt_tdf8532 snd_soc_skl snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_soc_sst_acpi snd_soc_sst_match snd_hda_ext_core snd_hda_core trusty_timer trusty_wall trusty_log trusty_virtio trusty_ipc trusty_mem trusty_irq trusty virtio_ring virtio intel_ipu4_mmu_bxtB0 lib2600_mod_bxtB0 intel_ipu4_isys_mod_bxtB0 lib2600psys_mod_bxtB0 intel_ipu4_psys_mod_bxtB0 intel_ipu4_mod_bxtB0 intel_ipu4_wrapper_bxtB0 intel_ipu4_acpi videobuf2_dma_contig as3638 dw9714 lm3643 crlmodule smiapp smiapp_pll
[ 46.884480] CPU: 1 PID: 33 Comm: kworker/u8:1 Tainted: G U W O 4.9.56-quilt-2e5dc0ac-g618ed69ced6e-dirty #4
[ 46.884489] Workqueue: events_unbound flush_to_ldisc
[ 46.884494] ffffb98ac012bb08 ffffffffad3e82e5 ffffb98ac012bb58 0000000000000000
[ 46.884497] ffffb98ac012bb48 ffffffffad0a23d1 00000024ad6374dd ffff9b2ab7289330
[ 46.884500] ffff9b2ab81e28e0 ffff9b2ab7289330 0000000000000002 0000000000000000
[ 46.884501] Call Trace:
[ 46.884507] [<ffffffffad3e82e5>] dump_stack+0x67/0x92
[ 46.884511] [<ffffffffad0a23d1>] __warn+0xd1/0xf0
[ 46.884513] [<ffffffffad0a244f>] warn_slowpath_fmt+0x5f/0x80
[ 46.884516] [<ffffffffad407443>] __list_add+0xb3/0xc0
[ 46.884521] [<ffffffffad71133c>] *usb_anchor_urb*+0x4c/0xa0
[ 46.884524] [<ffffffffad782c6f>] *acm_tty_flush_chars*+0x8f/0xb0
[ 46.884527] [<ffffffffad782cd1>] *acm_tty_put_char*+0x41/0x100
[ 46.884530] [<ffffffffad4ced34>] tty_put_char+0x24/0x40
[ 46.884533] [<ffffffffad4d3bf5>] do_output_char+0xa5/0x200
[ 46.884535] [<ffffffffad4d3e98>] __process_echoes+0x148/0x290
[ 46.884538] [<ffffffffad4d654c>] n_tty_receive_buf_common+0x57c/0xb00
[ 46.884541] [<ffffffffad4d6ae4>] n_tty_receive_buf2+0x14/0x20
[ 46.884543] [<ffffffffad4d9662>] tty_ldisc_receive_buf+0x22/0x50
[ 46.884545] [<ffffffffad4d9c05>] flush_to_ldisc+0xc5/0xe0
[ 46.884549] [<ffffffffad0bcfe8>] process_one_work+0x148/0x440
[ 46.884551] [<ffffffffad0bdc19>] worker_thread+0x69/0x4a0
[ 46.884554] [<ffffffffad0bdbb0>] ? max_active_store+0x80/0x80
[ 46.884556] [<ffffffffad0c2e10>] kthread+0x110/0x130
[ 46.884559] [<ffffffffad0c2d00>] ? kthread_park+0x60/0x60
[ 46.884563] [<ffffffffadad9917>] ret_from_fork+0x27/0x40
[ 46.884566] ---[ end trace 3bd599058b8a9eb3 ]---
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that USB_UHCI_BIG_ENDIAN_MMIO and USB_UHCI_BIG_ENDIAN_DESC are moved
outside of the USB_SUPPORT conditional, simply select them from
SPARC_LEON rather than by the symbol's defaults in drivers/usb/Kconfig,
similar to how it is done for USB_EHCI_BIG_ENDIAN_MMIO and
USB_EHCI_BIG_ENDIAN_DESC.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/18560/
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes: 2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Device ids found here:
usb 3-3: New USB device found, idVendor=1b1c, idProduct=1b13
usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3: Product: Corsair K70 RGB Gaming Keyboard
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition between finish_unlinks->finish_urb() function
and usb_kill_urb() in ohci controller case. The finish_urb calls
spin_unlock(&ohci->lock) before usb_hcd_giveback_urb() function call,
then if during this time, usb_kill_urb is called for another endpoint,
then new ed will be added to ed_rm_list at beginning for unlink, and
ed_rm_list will point to newly added.
When finish_urb() is completed in finish_unlinks() and ed->td_list
becomes empty as in below code (in finish_unlinks() function):
if (list_empty(&ed->td_list)) {
*last = ed->ed_next;
ed->ed_next = NULL;
} else if (ohci->rh_state == OHCI_RH_RUNNING) {
*last = ed->ed_next;
ed->ed_next = NULL;
ed_schedule(ohci, ed);
}
The *last = ed->ed_next will make ed_rm_list to point to ed->ed_next
and previously added ed by usb_kill_urb will be left unreferenced by
ed_rm_list. This causes usb_kill_urb() hang forever waiting for
finish_unlink to remove added ed from ed_rm_list.
The main reason for hang in this race condtion is addition and removal
of ed from ed_rm_list in the beginning during usb_kill_urb and later
last* is modified in finish_unlinks().
As suggested by Alan Stern, the solution for proper handling of
ohci->ed_rm_list is to remove ed from the ed_rm_list before finishing
any URBs. Then at the end, we can add ed back to the list if necessary.
This properly handle the updated ohci->ed_rm_list in usb_kill_urb().
Fixes: 977dcfdc60 ("USB: OHCI: don't lose track of EDs when a controller dies")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Aman Deep <aman.deep@samsung.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At former code, the SETUP stage does not enable interrupt
for qtd completion, it relies on IAA watchdog to complete
interrupt, then the transcation would be considered timeout
if the flag need_io_watchdog is cleared by platform code.
In this commit, we always add enable interrupt for qtd completion,
then the qtd completion can be notified by hardware interrupt.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for new CASSY devices to the ldusb driver. The
PIDs are also added to the ignore list in hid-quirks.
Signed-off-by: Karsten Koop <kkoop@ld-didactic.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b308 ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
converted to use hcd->self.sysdev for DMA operations instead of
hcd->self.controller, but forgot to do it for hcd test mode. Replace
the correct one in this commit.
Fixes: a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keep usbip_device sockfd state in sync with tcp_socket. When tcp_socket
is reset to null, reset sockfd to -1 to keep it in sync.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running io_watchdog_func() while ohci_urb_enqueue() is running can
cause a race condition where ohci->prev_frame_no is corrupted and the
watchdog can mis-detect following error:
ohci-platform 664a0800.usb: frame counter not updating; disabled
ohci-platform 664a0800.usb: HC died; cleaning up
Specifically, following scenario causes a race condition:
1. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
2. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
3. ohci_urb_enqueue() sets ohci->prev_frame_no to a frame number
read by ohci_frame_no(ohci)
4. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
5. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section
6. Later, ohci_urb_enqueue() is called
7. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
8. The timer scheduled on step 4 expires and io_watchdog_func() runs
9. io_watchdog_func() calls spin_lock_irqsave(&ohci->lock, flags)
and waits on it because ohci_urb_enqueue() is already in the
critical section on step 7
10. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
11. ohci_urb_enqueue() sets ohci->prev_frame_no to new frame number
read by ohci_frame_no(ohci) because the frame number proceeded
between step 3 and 6
12. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
13. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section, then wake up
io_watchdog_func() which is waiting on step 9
14. io_watchdog_func() enters the critical section
15. io_watchdog_func() calls ohci_frame_no(ohci) and set frame_no
variable to the frame number
16. io_watchdog_func() compares frame_no and ohci->prev_frame_no
On step 16, because this calling of io_watchdog_func() is scheduled on
step 4, the frame number set in ohci->prev_frame_no is expected to the
number set on step 3. However, ohci->prev_frame_no is overwritten on
step 11. Because step 16 is executed soon after step 11, the frame
number might not proceed, so ohci->prev_frame_no must equals to
frame_no.
To address above scenario, this patch introduces a special sentinel
value IO_WATCHDOG_OFF and set this value to ohci->prev_frame_no when
the watchdog is not pending or running. When ohci_urb_enqueue()
schedules the watchdog (step 4 and 12 above), it compares
ohci->prev_frame_no to IO_WATCHDOG_OFF so that ohci->prev_frame_no is
not overwritten while io_watchdog_func() is running.
Signed-off-by: Shigeru Yoshida <Shigeru.Yoshida@windriver.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Quectel EP06 is a Cat. 6 LTE modem, and the interface mapping is as
follows:
0: Diag
1: NMEA
2: AT
3: Modem
Interface 4 is QMI and interface 5 is ADB, so they are blacklisted.
This patch should also be considered for -stable. The QMI-patch for this
modem is already in the -stable-queue.
v1->v2:
* Updated commit prefix (thanks Johan Hovold)
* Updated commit message slightly.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function xhci_stop, xhci_debugfs_exit called before xhci_mem_cleanup.
xhci_debugfs_exit removed the xhci debugfs root nodes, xhci_mem_cleanup
called function xhci_free_virt_devices_depth_first which in turn called
function xhci_debugfs_remove_slot.
Function xhci_debugfs_remove_slot removed the nodes for devices, the nodes
folders are sub folder of xhci debugfs.
It is unreasonable to remove xhci debugfs root folder before
xhci debugfs sub folder. Function xhci_mem_cleanup should be called
before function xhci_debugfs_exit.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug after plugged out USB device, the device and its ep00
nodes are still kept, we need to remove the nodes in xhci_free_dev when
USB device is plugged out.
Fixes: 052f71e25a ("xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During system resume from hibernation, xhci host is reset, all the
nodes in devices folder are removed in xhci_mem_cleanup function.
Later nodes in /sys/kernel/debug/usb/xhci/* are created again in
function xhci_run, but the nodes already exist, so the nodes still
keep the old ones, finally device nodes in xhci debugfs folder
/sys/kernel/debug/usb/xhci/*/devices/* are disappeared.
This fix removed xhci debugfs nodes before the nodes are re-created,
so all the nodes in xhci debugfs can be re-created successfully.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disabling a USB3 port the hub driver will set the port link state to
U3 to prevent "ejected" or "safely removed" devices that are still
physically connected from immediately re-enumerating.
If the device was really unplugged, then error messages were printed
as the hub tries to set the U3 link state for a port that is no longer
enabled.
xhci-hcd ee000000.usb: Cannot set link state.
usb usb8-port1: cannot disable (err = -32)
Don't print error message in xhci-hub if hub tries to set port link state
for a disabled port. Return -ENODEV instead which also silences hub driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init()
must be doene before dwc3_core_get_phy().
commit 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
broke this.
The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should
be called only once during the life cycle of the driver. However,
as dwc3_core_init() is called during system suspend/resume it will
result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init()
which is wrong.
Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup()
into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that
dwc3_core_ulpi_init() is called only once from dwc3_core_init().
Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from
dwc3_core_init().
Fixes: 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
Fixes: f54edb539c ("usb: dwc3: core: initialize ULPI before trying to get the PHY")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.13
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the missing platform_device_put() before return from bdc_pci_probe()
in the platform_device_add_resources() error handling case.
Fixes: efed421a94 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
