PX-BCUD has the following components:
USB interface: Empia EM28178
Demodulator: Toshiba TC90532 (works by code for TC90522)
Tuner: Next version of Sharp QM1D1C0042
em28xx_dvb_init(): add init code for PLEX PX-BCUD with calling
px_bcud_init() that does things like pin configuration.
qm1d1c0042_init(): support the next version of QM1D1C0042, change to
choose an appropriate array of initial registers by reading chip id.
[mchehab@osg.samsung.com: fold a fixup patch and fix checkpatch.pl
errors/warnings, where applicable]
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Another version of Elgato EyeTV Sat USB DVB-S2 adapter needs just
a USB ID addition.
Signed-off-by: Christian Knippel <namerp@gmail.com>
Reported-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It's been reported that CJC7113 devices are returning
all 1s when reading register 0:
"1111111111111111" found @ 0x4a (stk1160)
This new device is apparently compatible with SA7113, so let's
add a quirk to allow its autodetection. Given there isn't
any known differences with SAA7113, this commit does not
introduces a new saa711x_model value.
Reported-by: Philippe Desrochers <desrochers.philippe@gmail.com>
Signed-off-by: Kevin Fitch <kfitch42@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Add a check for the case that both the cropcap and g_selection ops
are NULL. This shouldn't happen, but I feel happier if the code
guards against this.
- If g_selection exists, then ignore ENOTTY and ENOIOCTLCMD error
codes from cropcap. Just assume square pixelaspect ratio in that
case. This situation can happen if the bridge driver's cropcap op
calls the corresponding subdev's op. So the cropcap ioctl is set,
but it might return ENOIOCTLCMD anyway. In the past this would
just return an error which is wrong.
- Call cropcap first and let g_selection overwrite the bounds and
defrect. This safeguards against subdev cropcap implementations
that set those rectangles as well. What g_selection returns has
priority over what such cropcap implementations return.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some sensors (like the one in Nokia N900) provide metadata in the first
couple of lines. Make that information information available to the
pipeline.
Use u16 instead, this is a 16-bit value.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The devm_gpiod_get() function returns either a valid pointer to
struct gpio_desc or ERR_PTR() error value, check for NULL is bogus.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, dw2102 assumes that the USB IDs will be either at
an external header or defined internally. That doesn't sound
right.
So, let's move the definitions to just one place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add entries for all supported chip variants into the of_match list, so that
the matching driver_info can be selected when using dt.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Detect if firmware is running run-time and download / start it only
when needed. Detection is done by reading IF frequency value.
Garbage value is returned by firmware when it is not running,
otherwise correct value is returned.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using div_u64() instead of do_div() makes the code slightly more
readable by humans.
[mchehab@osg.samsung.org: originally, this patch was proposed as a bug
fix for a gcc bug. This was solved already, but it is still better to
use div_u64, instead of do_div, so I'm applying it, removing the
comments about the gcc bug]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXJoi6AAoJEHm+PkMAQRiGYKIIAIcocIV48DpGAHXFuSZbzw5D
rp9EbE5TormtddPz1J1zcqu9tl5H8tfxS+LvHqRaDXqQkbb0BWKttmEpKTm9mrH8
kfGNW8uwrEgTMMsar54BypAMMhHz4ITsj3VQX5QLSC5j6wixMcOmQ+IqH0Bwt3wr
Y5JXDtZRysI1GoMkSU7/qsQBjC7aaBa5VzVUiGvhV8DdvPVFQf73P89G1vzMKqb5
HRWbH4ieu6/mclLvW9N2QKGMHQntlB+9m2kG9nVWWbBSDxpAotwqQZFh3D52MBUy
6DH/PNgkVyDhX4vfjua0NrmXdwTfKxLWGxe4dZ8Z+JZP5c6pqWlClIPBCkjHj50=
=KLSM
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc6' into patchwork
Linux 4.6-rc6
* tag 'v4.6-rc6': (762 commits)
Linux 4.6-rc6
EDAC: i7core, sb_edac: Don't return NOTIFY_BAD from mce_decoder callback
Documentation/sysctl/vm.txt: update numa_zonelist_order description
lib/stackdepot.c: allow the stack trace hash to be zero
rapidio: fix potential NULL pointer dereference
mm/memory-failure: fix race with compound page split/merge
ocfs2/dlm: return zero if deref_done message is successfully handled
Ananth has moved
kcov: don't profile branches in kcov
kcov: don't trace the code coverage code
mm: wake kcompactd before kswapd's short sleep
.mailmap: add Frank Rowand
mm/hwpoison: fix wrong num_poisoned_pages accounting
mm: call swap_slot_free_notify() with page lock held
mm: vmscan: reclaim highmem zone if buffer_heads is over limit
numa: fix /proc/<pid>/numa_maps for THP
mm/huge_memory: replace VM_NO_THP VM_BUG_ON with actual VMA check
mailmap: fix Krzysztof Kozlowski's misspelled name
thp: keep huge zero page pinned until tlb flush
mm: exclude HugeTLB pages from THP page_mapped() logic
...
According to the V4L2 API, the VIDIOC_STREAMON ioctl should return EPIPE
if there is a format mismatch in the pipeline configuration.
As the .vidioc_streamon in the v4l2_ioctl_ops usually forwards the error
caused by the v4l2_subdev_link_validate_default (if it is in use), it
should return -EPIPE when it detect the mismatch.
When an entity is connected to a non enabled link,
media_entity_pipeline_start should return -ENOLINK, as the link does not
exist.
Signed-off-by: Helen Mae Koike Fornazier <helen.koike@collabora.co.uk>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=REYX
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some regression fixes:
- videobuf2 core: avoid the risk of going past buffer on multi-planes
and fix rw mode
- fix support for 4K formats at V4L2 core
- fix a trouble at davinci_fpe, caused by a bad patch
- usbvision: revert a patch with a partial fixup. The fixup patch
was merged already, and this one has some issues"
* tag 'media/v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] vb2-memops: Fix over allocation of frame vectors
[media] media: vb2: Fix regression on poll() for RW mode
[media] v4l2-dv-timings.h: fix polarity for 4k formats
[media] davinci_vpfe: Revert "staging: media: davinci_vpfe: remove,unnecessary ret variable"
[media] usbvision: revert commit 588afcc1
[media] videobuf2-v4l2: Verify planes array in buffer dequeueing
[media] videobuf2-core: Check user space planes array in dqbuf
Fix those two warnings:
drivers/media/pci/tw686x/tw686x-video.c:69 tw686x_fields_map() error: buffer overflow 'std_525_60' 31 <= 31
drivers/media/pci/tw686x/tw686x-video.c:73 tw686x_fields_map() error: buffer overflow 'std_625_50' 26 <= 26
I had those changes at the last version of my patch, but I ended
by merging the previous version by mistake.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On page unaligned frames, create_framevec forces get_vaddr_frames to
allocate an extra page at the end of the buffer. Under some
circumstances, this leads to -EINVAL on VIDIOC_QBUF.
E.g:
We have vm_a that vm_area that goes from 0x1000 to 0x3000. And a
frame that goes from 0x1800 to 0x2800, i.e. 2 pages.
frame_vector_create will be called with the following params:
get_vaddr_frames(0x1800, 2, write, 1, vec);
get_vaddr will allocate the first page after checking that the memory
0x1800-0x27ff is valid, but it will not allocate the second page because
the range 0x2800-0x37ff is out of the vm_a range. This results in
create_framevec returning -EFAULT
Error Trace:
[ 9083.793015] video0: VIDIOC_QBUF: 00:00:00.00000000 index=1,
type=vid-cap, flags=0x00002002, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b023ca80, length=5765760
[ 9083.793028] timecode=00:00:00 type=0, flags=0x00000000,
frames=0, userbits=0x00000000
[ 9083.793117] video0: VIDIOC_QBUF: error -22: 00:00:00.00000000
index=2, type=vid-cap, flags=0x00000000, field=any, sequence=0,
memory=userptr, bytesused=0, offset/userptr=0x7ff2b07bc500, length=5765760
Also use true instead of 1 since that argument is a bool in the
get_vaddr_frames() prototype.
Fixes: 21fb0cb7ec ("[media] vb2: Provide helpers for mapping virtual addresses")
Reported-by: Albert Antony <albert@newtec.dk>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
[hans.verkuil@cisco.com: merged the 'bool' change into this patch]
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org> # for v4.3 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When using a device is read/write mode, vb2 does not handle properly the
first select/poll operation.
The reason for this, is that when this code has been refactored, some of
the operations have changed their order, and now fileio emulator is not
started.
The reintroduced check to the core is enabled by a quirk flag, that
avoids this check by other subsystems like DVB.
Fixes: 49d8ab9fea ("media] media: videobuf2: Separate vb2_poll()")
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Cc: Junghak Sung <jh1009.sung@samsung.com>
Cc: <stable@vger.kernel.org> # for v4.5 and up
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Depending on the compiler version, currently it produces the
following warnings:
tw686x-video.c: In function 'tw686x_video_init':
tw686x-video.c:65:543: warning: array subscript is above array bounds [-Warray-bounds]
This is actually bogus with the current code, as it currently
hardcodes the framerate to 30 frames/sec, however a potential
use after the array size could happen when the driver adds support
for setting the framerate. So, fix it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Marking these controls as private seemed a good idea at one time,
but in practice it makes no sense. So drop this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The control in question is not a private control, so drop that
comment. Copy-and-paste left-over.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s_std ioctl was broken in this driver, partially due to the
changes to the adv7180 driver (this affected the handling of
V4L2_STD_ALL) and partially because the new standard was never
stored in vip->std.
The handling of V4L2_STD_ALL has been rewritten to just call querystd
and the new standard is now stored correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The adv7180 attempts to autodetect the standard. Unfortunately this
is seriously broken.
This patch removes the autodetect completely. Only the querystd op
will detect the standard. Since the design of the adv7180 requires
that you switch to a special autodetect mode you cannot call querystd
when you are streaming.
So the s_stream op has been added so we know whether we are streaming
or not, and if we are, then querystd returns EBUSY.
After testing this with a signal generator is became obvious that
a sleep is needed between changing the standard to autodetect and
reading the status. So the autodetect can never have worked well.
The s_std call now just sets the new standard without any querying.
If the driver supports the interrupt, then when it detects a standard
change it will signal that by sending the V4L2_EVENT_SOURCE_CHANGE
event.
With these changes this driver now behaves like all other video
receivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Federico Vaga <federico.vaga@gmail.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We print an uninitialized "actlen" variable on the error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When determining if the standard is 50 or 60 Hz it is standard
practice to test for 60 Hz instead of 50 Hz.
This doesn't matter normally, except if the user specifies both
60 and 50 Hz standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The test pattern generator will be used by other drivers as the virtual
media controller (vimc)
Signed-off-by: Helen Mae Koike Fornazier <helen.koike@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_rect helper functions have been moved to
include/media/v4l2-rect.h. Use this new header, dropping the functions
from vivid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of rolling our own define, just use the new mask defines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_device_call_* defines filter subdevs based on the grp_id value.
But some drivers use a bitmask, so instead of filtering by grp_id == value,
you want to filter by grp_id & value.
Make variants of these defines to do this.
The 'has_op' define has been extended to have a grp_id argument as well, and
a mask variant has been added.
This extra argument required a change to go7007.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ADV7180 supports NTSC, PAL and SECAM.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the pixel aspect ratio depending on the current
standard (50 vs 60 Hz).
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to get the standard to the adv7180 driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 588afcc1c0 ("[media] usbvision fix overflow of interfaces
array")' should be reverted, because:
* "!dev->actconfig->interface[ifnum]" won't catch a case where the value
is not NULL but some garbage. This way the system may crash later with
GPF.
* "(ifnum >= USB_MAXINTERFACES)" does not cover all the error
conditions. "ifnum" should be compared to "dev->actconfig->
desc.bNumInterfaces", i.e. compared to the number of "struct
usb_interface" kzalloc()-ed, not to USB_MAXINTERFACES.
* There is a "struct usb_device" leak in this error path, as there is
usb_get_dev(), but no usb_put_dev() on this path.
* There is a bug of the same type several lines below with number of
endpoints. The code is accessing hard-coded second endpoint
("interface->endpoint[1].desc") which may not exist. It would be great
to handle this in the same patch too.
* All the concerns above are resolved by already-accepted commit fa52bd50
("[media] usbvision: fix crash on detecting device with invalid
configuration")
* Mailing list message:
http://www.spinics.net/lists/linux-media/msg94832.html
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.5
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix this smatch error:
dib0090.c:1124 dib0090_pwm_gain_reset() error: we previously assumed 'state->rf_ramp' could be null (see line 1086)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These are false positives, but still easy to fix.
pvrusb2-hdw.c:3676 pvr2_send_request_ex() error: we previously assumed 'write_data' could be null (see line 3648)
pvrusb2-hdw.c:3829 pvr2_send_request_ex() error: we previously assumed 'read_data' could be null (see line 3649)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set vb2_queue.gfp_flags to GFP_DMA32. Otherwise it will start to
create bounce buffers which is something you want to avoid since
those are in limited supply.
Without this patch, DMA scatter-gather may not work because
machines can ran out of buffers easily.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commit introduces the support for the Techwell TW686x video
capture IC. This hardware supports a few DMA modes, including
scatter-gather and frame (contiguous).
This commit makes little use of the DMA engine and instead has
a memcpy based implementation. DMA frame and scatter-gather modes
support may be added in the future.
Currently supported chips:
- TW6864 (4 video channels),
- TW6865 (4 video channels, not tested, second generation chip),
- TW6868 (8 video channels but only 4 first channels using
built-in video decoder are supported, not tested),
- TW6869 (8 video channels, second generation chip).
[mchehab@osg.samsung.com: make checkpatch happy by using "unsigned int"
instead of just "unsigned"]
Cc: Krzysztof Halasa <khalasa@piap.pl>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, the lock schema for media_device struct is messy,
since sometimes, it is protected via a spin lock, while, for
media graph traversal, it is protected by a mutex.
Solve this conflict by always using a mutex.
As a side effect, this prevents a bug when the media notifiers
is called at atomic context, while running the notifier callback:
BUG: sleeping function called from invalid context at mm/slub.c:1289
in_atomic(): 1, irqs_disabled(): 0, pid: 3479, name: modprobe
4 locks held by modprobe/3479:
#0: (&dev->mutex){......}, at: [<ffffffff81ce8933>] __driver_attach+0xa3/0x160
#1: (&dev->mutex){......}, at: [<ffffffff81ce8941>] __driver_attach+0xb1/0x160
#2: (register_mutex#5){+.+.+.}, at: [<ffffffffa10596c7>] usb_audio_probe+0x257/0x1c90 [snd_usb_audio]
#3: (&(&mdev->lock)->rlock){+.+.+.}, at: [<ffffffffa0e6051b>] media_device_register_entity+0x1cb/0x700 [media]
CPU: 2 PID: 3479 Comm: modprobe Not tainted 4.5.0-rc3+ #49
Hardware name: /NUC5i7RYB, BIOS RYBDWi35.86A.0350.2015.0812.1722 08/12/2015
0000000000000000 ffff8803b3f6f288 ffffffff81933901 ffff8803c4bae000
ffff8803c4bae5c8 ffff8803b3f6f2b0 ffffffff811c6af5 ffff8803c4bae000
ffffffff8285d7f6 0000000000000509 ffff8803b3f6f2f0 ffffffff811c6ce5
Call Trace:
[<ffffffff81933901>] dump_stack+0x85/0xc4
[<ffffffff811c6af5>] ___might_sleep+0x245/0x3a0
[<ffffffff811c6ce5>] __might_sleep+0x95/0x1a0
[<ffffffff8155aade>] kmem_cache_alloc_trace+0x20e/0x300
[<ffffffffa0e66e3d>] ? media_add_link+0x4d/0x140 [media]
[<ffffffffa0e66e3d>] media_add_link+0x4d/0x140 [media]
[<ffffffffa0e69931>] media_create_pad_link+0xa1/0x600 [media]
[<ffffffffa0fe11b3>] au0828_media_graph_notify+0x173/0x360 [au0828]
[<ffffffffa0e68a6a>] ? media_gobj_create+0x1ba/0x480 [media]
[<ffffffffa0e606fb>] media_device_register_entity+0x3ab/0x700 [media]
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
s32tmp in the below code may be negative, and dev->mclk_khz is an
unsigned type.
s32tmp = 0x10000 * (tuner_frequency - c->frequency);
s32tmp = DIV_ROUND_CLOSEST(s32tmp, dev->mclk_khz);
This is undefined, as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is of unsigned type.
So, change mclk_khz to be signed (s32).
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The maximum image size supported by the WPF is 2048x2048 on Gen2 and
8190x8190 on Gen3. Update the code accordingly, and fix the maximum LIF
size for both Gen2 and Gen3.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The format is erroneously defined with an alpha channel. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the global alpha multiplier of DRM planes configurable. All the
necessary infrastructure is there, we just need to store the alpha value
passed through the DRM API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the Z-order of planes configurable by assigning RPFs to BRU inputs
dynamically based on the Z-order position.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Gen3 RPF includes an alpha multiplier that can both multiply the
alpha channel by a fixed global alpha value, and multiply the pixel
components to convert the input to premultiplied alpha.
As alpha premultiplication is available in the BRU for both Gen2 and
Gen3 we handle it there and use the Gen3 alpha multiplier for global
alpha multiplication only. This prevents conversion to premultiplied
alpha if no BRU is present in the pipeline, that use case will be
implemented later if needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Synchronize the userspace LUT setup with the pipeline operation by using
a display list fragment to store LUT data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Display lists support up to 8 bodies but we currently use a single one.
To support preparing display lists for large look-up tables, add support
for multi-body display lists.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vsp1_dl_list_put() function expects to be called with the display
list manager lock held. This assumption is correct for calls from within
the vsp1_dl.c file, but not for the external calls. Fix it by taking the
lock inside the function and providing an unlocked version for the
internal callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
