There are multiple places where DETECT_MODE is included in a register
write, but in every case it is written as 0. Removing these redundant
writes makes the code less cluttered and also makes it obvious that
DETECT_MODE is never changed.
A single initialization to 0 is added to cs42l42_setup_hs_type_detect().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211116163901.45390-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Interrupt Clear registers WCD938X_INTR_CLEAR_0 - WCD938X_INTR_CLEAR_2
are not marked as volatile. This has resulted in a missing interrupt bug
while performing runtime pm. regcache_sync() during runtime pm resume path
will write to Interrupt clear registers with previous values which basically
clears the pending interrupt and actual interrupt handler never sees this
interrupt.
This issue is more visible with headset plug-in plug-out case compared to
headset button.
Fix this by adding the Interrupt clear registers to volatile range
Fixes: 8d78602aa8 ("ASoC: codecs: wcd938x: add basic driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20211116114623.11891-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Considering the current transition of the GPIO subsystem, remove all
dependencies of the legacy GPIO interface (linux/gpio.h and linux
/of_gpio.h) and replace it with the descriptor-based GPIO approach.
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Link: https://lore.kernel.org/r/YXWo/9o7ye9a11aR@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
Revert 'I2S Reference' to SOC_ENUM_EXT because the settings are specific
for some platforms, the default setting for 'I2S Reference' does nothing,
only some SoC platform need to configure it.
Previous 'I2S Reference' in SOC_ENUM format only toggles one bit of
RT1011_TDM1_SET_1 register, which isn't enough for specific platform.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/20211111091705.20879-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (86 commits)
tty: Fix extra "not" in TTY_DRIVER_REAL_RAW description
serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE
tty: rpmsg: Define tty name via constant string literal
tty: rpmsg: Add pr_fmt() to prefix messages
tty: rpmsg: Use dev_err_probe() in ->probe()
tty: rpmsg: Unify variable used to keep an error code
tty: rpmsg: Assign returned id to a local variable
serial: stm32: push DMA RX data before suspending
serial: stm32: terminate / restart DMA transfer at suspend / resume
serial: stm32: rework RX dma initialization and release
serial: 8250_pci: Remove empty stub pci_quatech_exit()
serial: 8250_pci: Replace custom pci_match_id() implementation
serial: xilinx_uartps: Fix race condition causing stuck TX
serial: sunzilog: Mark sunzilog_putchar() __maybe_unused
Revert "tty: hvc: pass DMA capable memory to put_chars()"
Revert "virtio-console: remove unnecessary kmemdup()"
serial: 8250_pci: Replace dev_*() by pci_*() macros
serial: 8250_pci: Get rid of redundant 'else' keyword
serial: 8250_pci: Refactor the loop in pci_ite887x_init()
tty: add rpmsg driver
...
Currently the internal monitor sources are input widgets, which means
if the card is set to fully routed these will not enable unless connected
to something in the machine driver. However, all these are internal
monitor signals so it makes no sense to connect them to something in the
machine driver. As such switch them to siggen widgets which will have
the same behaviour except not require external linkage on a fully routed
card.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: David Rhodes <drhodes@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211029214028.401284-1-drhodes@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Summary: The driver applied the opposite of the DT setting to the
wrong register bit.
The jack plug detect hardware in cs42l42 is somewhat confusing,
compounded by an unclear description in the datasheet. This is most
likely the reason that the driver implemented a DT property for the
wrong register bit, that had the opposite effect of what was
described in the binding.
Changing the meaning of the property values isn't feasible; the
driver dates from 2016 and the risk of breaking out-of-tree configs
is too high (the property is also available to ACPI systems).
So the fix is to make the binding doc match the actual behaviour and
then fix the driver to apply it to the correct register bit.
As a bonus, patch #3 converts the binding to yaml.
Richard Fitzgerald (3):
ASoC: dt-bindings: cs42l42: Correct description of ts-inv
ASoC: cs42l42: Correct configuring of switch inversion from ts-inv
ASoC: dt-bindings: cs42l42: Convert binding to yaml
.../devicetree/bindings/sound/cirrus,cs42l42.yaml | 225 +++++++++++++++++++++
.../devicetree/bindings/sound/cs42l42.txt | 114 -----------
MAINTAINERS | 1 +
sound/soc/codecs/cs42l42.c | 9 +-
4 files changed, 230 insertions(+), 119 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/cirrus,cs42l42.yaml
delete mode 100644 Documentation/devicetree/bindings/sound/cs42l42.txt
--
2.11.0
The setting from the cirrus,ts-inv property should be applied to the
TIP_SENSE_INV bit, as this is the one that actually affects the jack
detect block. The TS_INV bit only swaps the meaning of the PLUG and
UNPLUG interrupts and should always be 1 for the interrupts to have
the normal meaning.
Due to some misunderstanding the driver had been implemented to
configure the TS_INV bit based on the jack switch polarity. This made
the interrupts behave the correct way around, but left the jack detect
block, button detect and analogue circuits always interpreting an open
switch as unplugged.
The signal chain inside the codec is:
SENSE pin -> TIP_SENSE_INV -> TS_INV -> (invert) -> interrupts
|
v
Jack detect,
button detect and
analog control
As the TIP_SENSE_INV already performs the necessary inversion the
TS_INV bit never needs to change. It must always be 1 to yield the
expected interrupt behaviour.
Some extra confusion has arisen because of the additional invert in the
interrupt path, meaning that a value applied to the TS_INV bit produces
the opposite effect of applying it to the TIP_SENSE_INV bit. The ts-inv
property has therefore always had the opposite effect to what might be
expected (0 = inverted, 1 = not inverted). To maintain the meaning of
the ts-inv property it must be inverted when applied to TIP_SENSE_INV.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211028140902.11786-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The series of features will make general and simple for new sof machine driver.
David Lin (2):
ASoC: nau8825: add set_jack coponment support
ASoC: nau8825: add clock management for power saving
sound/soc/codecs/nau8825.c | 48 ++++++++++++++++++++++++++++++++++++--
1 file changed, 46 insertions(+), 2 deletions(-)
cppcheck reports a false positive
sound/soc/codecs/nau8821.c:390:17: error: Array 'dmic_speed_sel[4]'
accessed at index 4, which is out of bounds. [arrayIndexOutOfBounds]
dmic_speed_sel[i].param, dmic_speed_sel[i].val);
^
sound/soc/codecs/nau8821.c:378:2: note: After for loop, i has value 4
for (i = 0 ; i < 4 ; i++)
^
sound/soc/codecs/nau8821.c:390:17: note: Array index out of bounds
dmic_speed_sel[i].param, dmic_speed_sel[i].val);
^
While the code is not incorrect, we can deal with the out-of-bounds
check in a clearer way that makes static analysis happy.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211025185933.144327-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
make W=1 reports warnings:
sound/soc/codecs/nau8821.c:1192: warning: Function parameter or member
'component' not described in 'nau8821_set_fll'
sound/soc/codecs/nau8821.c:1192: warning: Function parameter or member
'pll_id' not described in 'nau8821_set_fll'
sound/soc/codecs/nau8821.c:1192: warning: Function parameter or member
'source' not described in 'nau8821_set_fll'
sound/soc/codecs/nau8821.c:1192: warning: Excess function parameter
'codec' description in 'nau8821_set_fll'
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211025185933.144327-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports the following warnings:
sound/soc/codecs/rt5682s.c:44:12: error: symbol 'rt5682s_supply_names'
was not declared. Should it be static?
sound/soc/codecs/rt5682s.c:74:26: error: symbol 'rt5682s_reg' was not
declared. Should it be static?
sound/soc/codecs/rt5682s.c:2841:30: error: symbol
'rt5682s_aif1_dai_ops' was not declared. Should it be static?
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211025185933.144327-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver probe and remove were inconsistent in what they did to power-down
and neither did all steps. In addition to that, neither function
prevented the interrupt handler from running during and after power-down.
Richard Fitzgerald (2):
ASoC: cs42l42: Reset and power-down on remove() and failed probe()
ASoC: cs42l42: free_irq() before powering-down on probe() fail
sound/soc/codecs/cs42l42.c | 43 +++++++++++++++++++++++++++++++------------
1 file changed, 31 insertions(+), 12 deletions(-)
--
2.11.0
Relying on devm to free the irq handler on probe failure leaves a
small window of opportunity for an interrupt to become pending and
then the handler to run after the chip has been reset and powered
off.
For safety cs42l42_probe() should free the irq in the error path.
As the irq is now disabled by the driver in probe() and remove()
there is no point allocating it as a devres-managed item, so
convert to plain non-devres.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211026125722.10220-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt handling code was getting the struct device* from a
struct snd_soc_component* stored in struct cs42l42_private. If the
interrupt was asserted before ASoC calls component_probe() the
snd_soc_component* will be NULL.
The stored snd_soc_component* is not actually used for anything other
than indirectly getting the struct device*. Remove it, and store the
struct device* in struct cs42l42_private.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211025112258.9282-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has runtime_suspend and runtime_resume callbacks, but
pm_runtime is never enabled so these functions won't be called. They
could not be used anyway because the runtime_suspend would cause jack
detect to stop working.
These functions are unused - delete them.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211018164431.5871-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
