Due to access control RGF_CAF_ICR cannot be accessed by host.
Such an access will cause device AHB logger to halt and it will not
capture future AHB fault if there is any.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The functions that send management TX frame have 3 possible
results: success and other side acknowledged receive (ACK=1),
success and other side did not acknowledge receive(ACK=0) and
failure to send the frame. The current implementation
incorrectly reports the ACK=0 case as failure.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update the rx packet checksum of received packet according to edma
HW spec:
No need to calculate checksum in the following cases:
L4_status=0 and L3_status=0 - No L3 and no L4 known protocols found
L4_status=0 and L3_status=1 - L3 was found, and checksum check passed.
No known L4 protocol was found.
L4_status=1 - L4 was found, and checksum check passed.
Recalculate checksum in the following cases:
L4_status=3 and L3_status=1 - It means that L3 protocol was found,
and checksum passed, but L4 checksum failed.
L4_status=3 and L3_status=2 - Both L3 and L4 checksum check failed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In addition to existing MAC address field in OTP, new field added for
OEM MAC address.
wil6210 gives precedence to the new OEM MAC address and will use it if
its valid.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check that the mid is valid and that it does not exceed the memory
size allocated to vifs array.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update max MCS to 15, which is supported by Talyn-MB.
This will allow collecting statistics on number of RX packets
in higher MCS.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In Sparrow, FW might sleep long time due to T_Power_On calculation
in slow clock, so T_Power_On was set to zero to shorten the L1SS
wake-up time.
In Talyn-MB the L1SS wake-up procedure is handled by the PMU (HW),
hence T_Power_On calculation is accurate and should not be forced
to zero.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case there are connected stations, FW needs to disconnect
them before handling PCP stop. This flow can take several
seconds.
Increasing PCP stop timeout to 5 seconds to allow that.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Accessing some of the memory of the device while the device is
resetting or suspending may cause unexpected error as the HW is still
not in a stable state. Prevent this access to guarantee successful
read/write memory operations.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HALP ICR is set as long as the FW should stay awake.
To prevent its multiple handling the driver masks this IRQ bit.
However, if there is a different MISC ICR before the driver clears
this bit, there is a risk of race condition between HALP mask and
unmask. This race leads to HALP timeout, in case it is mistakenly
masked.
Add an atomic flag to indicate if HALP ICR should be handled.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon status ring handling, in case there are both unicast and
multicast (cid == max) status messages to handle, wrong sta statistics
might get updated.
Fix this by setting stats to NULL upon invalid cid
(e.g. == max_assoc_sta).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rearrange the code by having functions to access 802.3 header
members, source and destination addresses.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW added support for upto 20 clients in AP mode. Change the driver
to support this as well. FW reports it's max supported associations in
WMI_READY_EVENT. Some WMI commands/events use cidxtid field which is
limited to 16 cids. Use new cid/tid fields instead.
For Rx packets cid from rx descriptor is limited to 3 bits (0..7),
to find the real cid, compare transmitter address with the stored
stations mac address in the driver sta array.
EDMA FW still supports 8 stations. Extending the support to 20
stations will come later.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In AP mode with multiple clients, driver stops net queue
(netif_tx_stop_queue) upon first ring (serving specific client)
becoming full. This can have negative effect on transmission to
other clients which may still have room in their corresponding rings.
Implement new policy in which stop/wake net queue are not used. In
case there is no room in the ring for a transmitted packet, drop the
packet.
New policy can be helpful to debug performance issues, to guarantee
maximum utilization of net queues.
New policy is disabled by default and can be enabled by debugfs:
echo 1 > drop_if_ring_full
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to a HW issue in PHY info collection rtap_include_phy_info is not
in use, hence can be removed.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/main.c: In function '_wil6210_disconnect':
drivers/net/wireless/ath/wil6210/main.c:407:23: warning:
variable 'wdev' set but not used [-Wunused-but-set-variable]
It never used since commit ("e1b43407c034 wil6210: refactor disconnect flow")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Switch from spin_lock to spin_lock_irqsave, because
wmi_ev_lock is used inside interrupt handler.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After being associated with some EDMA rx traffic, upon "down" driver
doesn't free all skbs in the rx ring.
Modify wil_move_all_rx_buff_to_free_list to loop on active list of rx
buffers, unmap the physical memory and free the skb.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx buffers in EDMA mode are initialized to 4 bytes aligned size.
Remove the unnecessary alignment code applied on rx buffer size.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RGF_CAF_ICR register location has changed in Talyn-MB.
Add RGF_CAF_ICR_TALYN_MB to support the new address.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
L2 RX status errors should not be treated as a bitmap and the actual
error values should be checked.
Print L2 errors as wil_err_ratelimited for easier debugging
when such errors occurs.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All wil6210 device memory access should be 4 bytes aligned. In io
blob wil6210 did not force alignment for read function, this caused
alignment fault on some platforms.
Fixing that by accessing all 4 lower bytes and return to host the
requested data.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil6210 used to notify cfg80211_del_sta on every fw disconnect event.
In disable_ap_sme mode the userspace manages the protocol SME and
FW sends disconnect event only due to link loss.
In disable_ap_sme mode, indicate CQM packet loss to let the host
control the connection and disconnect the link if needed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Separate sending command to the fw from the event handling function to
simplify the disconnect flow and track the from_event flag correctly.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A successful call to wil_tx_ring takes skb reference so
it will only be freed in wil_tx_complete. Consume the skb
in wil_find_tx_bcast_2 to prevent memory leak.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AP configuration is stored by the driver. Upon FW error, disconnect
notification is sent to user space for any associated stations. AP is
then internally restarted with the stored configuration.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When enlarging rx_ring_order module param, wil6210 fails to load
because there are not enough Rx buffers.
Fix this by enlarging number of Rx buffers at startup, if needed based
on rx_ring_order.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In Talyn-MB, the 11ad throughput is higher and performance drops
may occur in the current RX configuration due to unavailability
of Rx buffers.
Increase the RX descriptor ring, RX status ring and number of RX
buffers to stabilize the performance in high throughput.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With current reset flow, Talyn sometimes get stuck causing PCIe
enumeration to fail. Fix this by removing some reset flow operations
that are not relevant for Talyn.
Setting bit 15 in RGF_HP_CTRL is WBE specific and is not in use for
all wil6210 devices.
For Sparrow, BIT_HPAL_PERST_FROM_PAD and BIT_CAR_PERST_RST were set
as a WA an HW issue.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.20. Major changes:
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/pm.c: In function 'wil_suspend_keep_radio_on':
drivers/net/wireless/ath/wil6210/pm.c:193:16: warning:
variable 'start' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The comparison of cid >= 0 is always true because cid is of type u8
(8 bits, unsigned).
Fix this by removing such comparison and updating the type of
variable cid to u8 in the caller function.
Addresses-Coverity-ID: 1473079 ("Unsigned compared against 0")
Fixes: b9010f105f ("wil6210: add FT roam support for AP and station")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This feature is needed for enterprise APs and clients to enable
fast roaming as defined in 802.11r between APs in the same ESS.
On AP side, this feature is supported only when disable_ap_sme
is enabled.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RX SKBs are released in both wil6210 rmmod and RX handle.
As there is no lock to protect the buffers DMA unmap,
the SKB pointer in buff_arr is used to check if the buffer
memory was already released.
Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA
memory unmap will prevent duplicate unmapping of the same memory.
Move the buffer ID to the free list also in case the SKB is NULL.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In enhanced DMA ring 0 is used for RX ring, hence TX ring 0
is an unused element in ring_tx and ring2cid_tid arrays.
Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false
match of CID 0.
Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id
and on to prevent access to index 0 in eDMA.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil_addba_rx_request allocates the rx reorder buffer regardless
of use_rx_hw_reordering settings.
Fix this by checking wil->use_rx_hw_reordering before allocating
the reorder buffer.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
use_rx_hw_reordering is already set to true in wil_set_capabilities
for Talyn-MB devices. Remove its setting from wil_priv_init to
prevent its activation for older chips.
Similarly, move the setting of use_compressed_rx_status to
wil_set_capabilities.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Delivering a looped-back multicast packet to network stack can cause
higher layer protocols to fail like for example IPv6 DAD.
In STA mode, upon receiving Rx multicast packet, check if the source
MAC address is equal to our own MAC address and if so drop the packet.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wil6210 supports channels 1-3 of the 60GHz band.
New FW added support for channel 4. Add support for channel 4 also in
wil6210 driver.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset file is not used and may cause race conditions
with operational driver if used.
Signed-off-by: Karthick Gopalasubramanian <kargop@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
