[why]
on some displays that prefer swapped polarity we were seeing L/R images
swapped because OTG_STEREO_SYNC_OUTPUT_POLARITY would always be mapped
to 0
[how]
fix initial dal3 implementation to properly update the polarity field
according to the crtc_stereo_flags (same as
OTG_STEREO_EYE_FLAG_POLARITY)
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In HDCP Uninitialzed State, a CPIRQ event would cause log output
internal policy error because the CPIRQ event is not recognized as
unexpected event.
[how]
CPIRQ is issued in HDCP uninitialized state is unexpected. We should
set unexpected event flag in event ctx.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some RX doesn't like us to read rx id list upto max rx id list size. As
discussed, we decided to read rx id list based on device count.
[how]
According to HDCP specs the actual size of rx id list is calculated as
rx id list size = 2+3+16+5*device_count. We will read 16 bytes at a
time until it reached or exceeded rx id list size.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Link or DIG BE can't be exposed to a higher stream bandwidth than they
can handle. When DSC is required to fit the stream into the link
bandwidth, DSC has to be programmed during timing programming to ensure
this. Without it, intermittent issues such as black screen after S3 or a
hot-plug can be seen.
[how]
Move DSC programming from enabling stream on link to timing setup.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System isn't able to enter S0i3 due to not send display count 0 to smu.
When dpms off, clk changed flag is cleared alreay, and it is checked
when doing optimized bandwidth, and update clocks is bypassed due to the
flag is unset.
[How]
Remove check flag incide the function since watermark values and clocks
values are checked during update to determine whether to perform it, no
need to check it again outside the function.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is possible even if sink signal is MST but driver enables SST stream.
We should not determine if we should do MST authentication based on
sink's capability.
Instead we should determine whether to do MST authentication based on
what we have enabled in stream.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
So the values of stay count and bstatus can be easily viewed during
debugging.
[How]
Add stay count and bstatus values to be outputted in HDCP log
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
nv14 previously inherited soc bb from generic dcn 2, did not match
watermark values according to memory team
[how]
add nv14 specific soc bb: copy nv2 generic that it was
using from before, but changed num channels to 8
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
dc_hardware_init -> amdgpu_dm_init
dc_set_power_state --> dm_resume
therefore, linux dc-pplib interface of navi10/12/14 is different
from that of Renoir.
v2: add missing unlock in error case
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:31: warning:
address of 'pipe_ctx->plane_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:147:56: warning:
address of 'pipe_ctx->stream_res' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!pipe_ctx || !&pipe_ctx->plane_res || !&pipe_ctx->stream_res)
~ ~~~~~~~~~~^~~~~~~~~~
2 warnings generated.
As long as pipe_ctx is not NULL, the address of members in this struct
cannot be NULL, which means these checks will always evaluate to false.
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Link: https://github.com/ClangBuiltLinux/linux/issues/915
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
dc_hardware_init -> amdgpu_dm_init
dc_set_power_state --> dm_resume
therefore, linux dc-pplib interface of navi10/12/14 is different
from that of Renoir.
v2: add missing unlock in error case
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Logger mask was updated to uint64_t, however default mask definition was
not updated for unsigned long long
[How]
Update DC_DEFAULT_LOG_MASK to support uint64_t type
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see an issue that caused clk_optimized_required to be set true in
certain cases, causing passive flips to fail. This is because of a typo
where wm_optimized_required was set twice.
[HOW]
Set clk_optimized_required to false after updating clocks.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SMU FW previously had an issue with lowering display clock to below 100
MHz, and a workaround was put in to limit it. Newest SMU FW does not
have this issue, and no longer needs the 100MHz cap.
[HOW]
Remove the 100MHz cap based on the SMU FW version.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When transitioning from SST to MST, the HDCP repeater in some MST
displays will enter a bad state. The HDCP repeater is recovered after
failing and performing authentication again.
[How]
Add monitor patch to trigger HDCP authentication failure after
encryption is enabled and re-authenticate.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When test pattern is enabled with ODM combine, test pattern is generated
by piecing multiple DPGs image together. The current code will program
all DPGs with horizontal offset of 0. This will cause all DPGs to output
the beginning of the pattern. Instead each DPG should program a
horizontal offset of its x position to form a continous pattern when
pieced together.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Allow vsc info packet if vsc is supported. Update vsc based on test
pattern request. Remove dpg_is_blanked polling, apply hardware global
lock instead to ensure double buffered dpg is updated with vsc in one
frame
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Typo in amdgpu_dm error message:
"Failed to found connector for link!"
[How]
1. Replace with:
"Failed to find connector for link!"
2. Fix indentation checkpatch warnings.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
In order to correctly intepret clock table, num_states is also needed.
This field did not get moved with clock_table but should next to it for
easier access/viewing.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some asics don't support FEC but FEC overhead is added into link
bandwidth calculation by mistake. This causes certain timing cannot be
validated.
[how]
Only include FEC overhead if both asic and display support FEC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to be able to enable PSR on DMCUB, and fallback to
DMCU when necessary.
[How]
Move psr_on_dmub flag from dc_debug_options to dc_config.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reset connection is called before remove display in mod_hdcp. When
remove display is called, the display structure has been zeroed from
reset connection. Since no displays can be found, remove display does
not properly reset the hardware. This causes validation errors when
another display is plugged into a different port afterwards.
[How]
Moved displays structure out of connections structure. Displays
structure is now directly within mod_hdcp. Displays is no longer zeroed
when reset connection is called.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously implemented early_cr_pattern we mistook dp_hw_link_settings
for a redundant call of dpcd_set_link_settings
[How]
revert the changes to dpcd_set_link_settings calls for this workaround.
Do not need to revert the entire change since it only affects patched
case
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: David Galiffi <David.Galiffi@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removes codestyle issues on detect_dp function as suggested by
checkpatch.pl.
CHECK: Lines should not end with a '('
WARNING: Missing a blank line after declarations
WARNING: line over 80 characters
CHECK: Alignment should match open parenthesis
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Coding style clean up on enable_link_dp function as suggested by
checkpatch.pl:
CHECK: Lines should not end with a '('
WARNING: line over 80 characters
WARNING: suspect code indent for conditional statements (8, 24)
CHECK: braces {} should be used on all arms of this statement
ERROR: else should follow close brace '}'
CHECK: Comparison to NULL could be written
"link->preferred_training_settings.fec_enable"
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is freeing the wrong variable so it will crash. It should be
freeing "*dmub" instead of "dmub".
Fixes: 4c1a1335df ("drm/amd/display: Driverside changes to support PSR in DMCUB")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are multiple statements that are indented incorrectly. Add
in the missing tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nothing else calls it. Not sure it's necessary.
v2: remove unused port variable.
Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split into init and register functions to avoid a segfault
in some configs when the load/unload callbacks are removed.
v2:
- add back accidently dropped has_aux setting
- set dev in late_register
v3:
- fix dp cec ordering
v4:
- squash in kdev reference fix
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In order to remove the load and unload drm callbacks,
we need to reorder the init sequence to move all the drm
debugfs file handling. Do this for display.
v2: add config guard for DC
Tested-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com> (v1)
Acked-by: Christian König <christian.koenig@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the existence of the workqueue itself to determine when to
enable HDCP features rather than sprinkling asic checks all over
the code. Also add a check for the existence of the hdcp
workqueue in the irq handling on the off chance we get and HPD
RX interrupt with the CP bit set. This avoids a crash if
the driver doesn't support HDCP for a particular asic.
Fixes: 96a3b32e67 ("drm/amd/display: only enable HDCP for DCN+")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=206519
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
