Configuring counters from the userspace require the kernel to handle some
logic related to performance counters. Basically, it has to find a free
slot to assign a counter, to handle extra counting modes like B4/B6 and it
must return and error when it can't configure a counter.
In my opinion, the kernel should not handle all of that logic but it
should only write the configuration sent by the userspace without
checking anything. In other words, it should overwrite the configuration
even if it's already counting and do not return any errors.
This patch allows the userspace to configure a domain instead of
separate counters. This has the advantage to move all of the logic to
the userspace.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This adds a new method NVIF_PERFCTR_V0_INIT which starts a batch of
hardware counters for sampling. This will allow the userspace to start
a monitoring session using the INIT method and to stop it with SAMPLE,
for example before and after a frame is rendered.
This commit temporarily breaks nv_perfmon but this is going to be fixed
with the upcoming patch.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This allows to query the ID, the mask and the user-readable name of
sources for each signal.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A source (or multiplexer) is a tuple addr+mask+shift which allows to
control a block of signals. The maximum number of sources that a signal
can define is arbitrary limited to 8 and this should be large enough.
This patch allows to define multi-level of sources for a signal.
Each different sources are stored to a global list and will be exposed
to the userspace through the nvif interface in order to avoid conflicts.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset at gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This signal index must be always allowed even if it's not clearly
defined in a domain in order to monitor a counter like 0x03020100
because it's the default value of signals.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
16 bits is large enough to store the maximum number of signals available
for one domain (i.e. 256).
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will allow to configure performance counters with hardware signal
indexes instead of user-readable names in an upcoming patch.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This allows to query the number of available domains, including the
number of hardware counter and the number of signals per domain.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Since a new class has been introduced to query signals, we can now
return an error when the userspace wants to monitor unknown signals.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This commit introduces the NVIF_IOCTL_NEW_V0_PERFMON class which will be
used in order to query domains, signals and sources. This separates the
querying and the counting interface.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
PDAEMON signals don't have to be exposed by the perfmon engine.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested on a few cards. Probably works quite well for most, given they should
all be GDDR3.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This looks surprisingly similar to scripts on earlier cards as well
but they don't seem to work just yet. That... and I don't have any, which
makes it a tough job to reverse engineer.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some of the bits in there are similar to the bits in the gt215 rammap.
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Might need some generalisation to < GT200. For those: use at your own risk!
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
In preparation of NV50 reclocking, where there is no version
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Here are some development updates for the Synopsis Designware HDMI driver,
which clean up some of the code, and start preparing to add audio support
to the driver. This series of patches are based on a couple of dependent
commits from the ALSA tree.
Briefly, the updates are:
- move comments which should have moved with the phy values to the IMX
part of the driver.
- clean up the phy configuration: to all lookups before starting to
program the phy.
- clean up the HDMI clock regenerator code
- use the drm_hdmi_avi_infoframe_from_display_mode() helper which allows
the code to be subsequently simplified
- remove the unused 'regmap' pointer in struct dw_hdmi
- use the bridge drm device rather than the connector (we're the bridge
code)
- remove private hsync/vsync/interlaced flags, getting them from the
DRM mode structure instead.
- implement interface functions to support audio - setting the audio
sample rate, and enabling the audio clocks.
- removal of broken pixel repetition support
- cleanup DVI vs HDMI sink handling
- enable audio only if connected device supports audio
- avoid double-enabling bridge in the sink path (once in mode_set, and
again in commit)
- rename mis-named dw_hdmi_phy_enable_power()
- fix bridge enable/disable handing, so a plug-in event doesn't
reconfigure the bridge if DRM has disabled the output
- fix from Vladimir Zapolskiy for the I2CM_ADDRESS macro name
These are primerily preparitory patches for the AHB audio driver and
the I2S audio driver (from Rockchip) for this IP.
* 'drm-dwhdmi-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm: bridge/dw_hdmi: fix register I2CM_ADDRESS register name
drm: bridge/dw_hdmi: fix phy enable/disable handling
drm: bridge/dw_hdmi: rename dw_hdmi_phy_enable_power()
drm: bridge/dw_hdmi: avoid enabling interface in mode_set
drm: bridge/dw_hdmi: enable audio only if sink supports audio
drm: bridge/dw_hdmi: clean up HDMI vs DVI mode handling
drm: bridge/dw_hdmi: don't support any pixel doubled modes
drm: bridge/dw_hdmi: remove pixel repetition setting for all VICs
drm: bridge/dw_hdmi: introduce interfaces to enable and disable audio
drm: bridge/dw_hdmi: introduce interface to setting sample rate
drm: bridge/dw_hdmi: remove mhsyncpolarity/mvsyncpolarity/minterlaced
drm: bridge/dw_hdmi: use our own drm_device
drm: bridge/dw_hdmi: remove unused 'regmap' struct member
drm: bridge/dw_hdmi: simplify hdmi_config_AVI() a little
drm: bridge/dw_hdmi: use drm_hdmi_avi_infoframe_from_display_mode()
drm: bridge/dw_hdmi: clean up hdmi_set_clk_regenerator()
drm: bridge/dw_hdmi: clean up phy configuration
drm: imx/dw_hdmi: move phy comments
drm/edid: add function to help find SADs
Pull request of 15-08-21
The third pull request for 4.3. Contains two fixes for regressions introduced
with previous pull requests.
* tag 'vmwgfx-next-15-08-21' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Remove duplicate ttm_bo_device_release
drm/vmwgfx: Fix a circular locking dependency in the fbdev code
- DP fixes for radeon and amdgpu
- IH ring fix for tonga and fiji
- Lots of GPU scheduler fixes
- Misc additional fixes
* 'drm-next-4.3' of git://people.freedesktop.org/~agd5f/linux: (42 commits)
drm/amdgpu: fix wait queue handling in the scheduler
drm/amdgpu: remove extra parameters from scheduler callbacks
drm/amdgpu: wake up scheduler only when neccessary
drm/amdgpu: remove entity idle timeout v2
drm/amdgpu: fix postclose order
drm/amdgpu: use IB for copy buffer of eviction
drm/amdgpu: adjust the judgement of removing fence callback
drm/amdgpu: fix no sync_wait in copy_buffer
drm/amdgpu: fix last_vm_update fence is not effetive for sched fence
drm/amdgpu: add priv data to sched
drm/amdgpu: add owner for sched fence
drm/amdgpu: remove entity reference from sched fence
drm/amdgpu: fix and cleanup amd_sched_entity_push_job
drm/amdgpu: remove amdgpu_bo_list_clone
drm/amdgpu: remove the context from amdgpu_job
drm/amdgpu: remove unused parameters to amd_sched_create
drm/amdgpu: remove sched_lock
drm/amdgpu: remove prepare_job callback
drm/amdgpu: cleanup a scheduler function name
drm/amdgpu: reorder scheduler functions
...
Freeing up a queue after signalling it isn't race free.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Removing the entity from scheduling can deadlock the whole system.
Wait forever till the remaining IBs are scheduled.
v2: fix comment as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com> (v1)
The context needs to finish before everything else.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This aids handling buffers moves with the scheduler.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
The fence in the array may be skipped if wait_all is false,
thus the related callback is not initialized with list head.
So removing this kind callback will cause NULL pointer reference.
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
v2: fix one error found by checkpath.pl
v3: Add one ignored break for switch-case. DDI-E hotplug
function doesn't work after updating drm-intel tree,
I checked the code and found this missing which isn't
the root cause for broke DDI-E hp. The broken
DDI-E hp function is fixed by "Adding DDI_E power
well domain".
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Timo Aaltonen <timo.aaltonen@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The gtt.stolen_size field is of type size_t, and so should be printed
using %zu to avoid build warnings on either 32-bit and 64-bit builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
SKL-Y can now use the same programming for all VccIO values after an
adjustment to I_boost. SKL-U DP table adjustments.
1. Remove SKL Y 0.95V from "SKL H and S" columns in all tables. The
other SKL Y column removes the "0.85V VccIO" so it now applies to all
voltages.
2. DP table changes SKL U 400mV+0db dword 0 value from 2016h to 201Bh.
3. DP table changes SKL U 600mv+0db dword 0 value from 2016h to 201Bh.
4. DP table increases I_boost to level 3 for SKL Y 400mv+9.5db.
v2: Fix compilation warnings as pointed by Paulo.
Reference: Graphics Spec Change r97962
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[Jani: reformatted commit message for shorter lines.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The registers will be reset to default values when whole
power domain off, so restore registers from regsbak.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Win2/3 support multiple area function, but we haven't found
a suitable way to use it yet, so let's just use them as other windows
with only area 0 enabled.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
vir_stride need number words of the virtual width, and fb->pitches
save bytes_per_pixel, so just div 4 switch to stride.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
when eviction is happening, if don't handle
dependency, then the fence could be dead off.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
Entity don't live as long as scheduler fences.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Calling schedule() is probably the worse things we can do.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Keep run queue, entity and scheduler handling together.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Cleanup function name, stop checking scheduler ready twice, but
check if kernel thread should stop instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
None of them are used any more.
v2: fix type in error message
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
Remove active_hw_rq and it's protecting queue_lock, they are unused.
User 32bit atomic for hw_rq_count, 64bits for counting to three is a bit
overkill.
Cleanup the function name and remove incorrect comments.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Simply not used any more. Only keep 32bit atomic for fence sequence numbering.
v2: trivial rebase
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com> (v1)
Reviewed-by: Chunming Zhou <david1.zhou@amd.com> (v1)
Rename the function and update the related code with this modified function.
Add the new parameter of bool wait_all.
If wait_all is true, it will return when all fences are signaled or timeout.
If wait_all is false, it will return when any fence is signaled or timeout.
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Use pci_alloc_consistent rather than kzalloc since we
need 256 byte aligned memory for the ring buffer.
v2: fix copy paste typo in free function noticed
by Jammy.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91749
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This reverts commit 992cbf19b3.
Until we make fbdev layer atomic we can't call this.
Requested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com?
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Cc: Wentao Xu <wentaox@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
VBT version 196 increased the size of common_child_dev_config. The
parser code assumed that the size of this structure would not change.
The modified code now copies the amount needed based on the VBT version,
and emits a debug message if the VBT version is unknown (too new); since
the struct config block won't shrink in newer versions it should be
harmless to copy the maximum known size in such cases, so that's what we
do, but emitting the warning is probably sensible anyway.
In the longer run it might make sense to modify the parser code to use a
version/feature mapping, rather than hardcoding things like this, but
for now the variants are fairly manageable.
This fixes a regression introduced in
commit 75067ddecf
Author: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Date: Fri Jul 10 14:10:55 2015 +0300
drm/i915: Per-DDI I_boost override
since that commit changed the child device config size without updating
the checks and memcpy.
v2: Stricter size checks
v3 by Jani:
- Keep the checks strict, and warnigns verbose, but keep going anyway.
- Take care to copy the max amount of child device config we can.
- Fix the messages.
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch fixes the bug that SKL SKUs before B0 might return
HBR2 as supported even though it is not supposed to be enabled
on such platforms.
v2: optimize if else condition (Jani)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[Jani: minor whitespace fix.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit 75067ddecf
Author: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Date: Fri Jul 10 14:10:55 2015 +0300
drm/i915: Per-DDI I_boost override
increased size of union child_device_config without taking into account
the size check in parse_sdvo_device_mapping(). Switch the function over
to using the legacy struct only.
Fixes: 75067ddecf ("drm/i915: Per-DDI I_boost override")
Cc: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV2pUkAAoJEHm+PkMAQRiGCIoH/Rb29ZjdCoZJp9OtnjAG+qRc
bG3YuomIdib86x7xHRKKaLWBa7din7IYjuwT/X4S4duO5a1R5Lp1sRG3IlGfhT0W
nBNbjFl4q4bOyiTPtTRTYyh4g5UQv4IuyCnCmZyCTJyVi/O6HVM9TWKUzm68P2dJ
30LwLUcQJ+mHueGJwFBAXe2BaojEpvYCdSX6tvbrQ/8X3FrVExZXuJl4uMYNFYNK
ZwG/v5t7tYOiAe76JGbrEuVFPZWLPEW7amHOWR0T4Ye4nWTlBgx7fENiNRlfgcvI
CM16l/xkyrZQ3Q5jZy1qYDfdHYF++dyEDysX4w1ae/X0aaLZn7l+u5VQD6WpkQQ=
=IF6I
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc8' into drm-next
Linux 4.2-rc8
Backmerge required for Intel so they can fix their -next tree up properly.
- Added PLL algorithm for a new rev of G200e
- Removed the bandwidth limitation for the new G200e
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Added support for the new deviceID for G200eW3
- Added PLL algorithm for the G200eW3
- Added some initialization code for G200eW3
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a port of:
DRM - radeon: Don't link train DisplayPort on HPD until we get the dpcd
to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Most of the time this isn't an issue since hotplugging an adaptor will
trigger a crtc mode change which in turn, causes the driver to probe
every DisplayPort for a dpcd. However, in cases where hotplugging
doesn't cause a mode change (specifically when one unplugs a monitor
from a DisplayPort connector, then plugs that same monitor back in
seconds later on the same port without any other monitors connected), we
never probe for the dpcd before starting the initial link training. What
happens from there looks like this:
- GPU has only one monitor connected. It's connected via
DisplayPort, and does not go through an adaptor of any sort.
- User unplugs DisplayPort connector from GPU.
- Change in HPD is detected by the driver, we probe every
DisplayPort for a possible connection.
- Probe the port the user originally had the monitor connected
on for it's dpcd. This fails, and we clear the first (and only
the first) byte of the dpcd to indicate we no longer have a
dpcd for this port.
- User plugs the previously disconnected monitor back into the
same DisplayPort.
- radeon_connector_hotplug() is called before everyone else,
and tries to handle the link training. Since only the first
byte of the dpcd is zeroed, the driver is able to complete
link training but does so against the wrong dpcd, causing it
to initialize the link with the wrong settings.
- Display stays blank (usually), dpcd is probed after the
initial link training, and the driver prints no obvious
messages to the log.
In theory, since only one byte of the dpcd is chopped off (specifically,
the byte that contains the revision information for DisplayPort), it's
not entirely impossible that this bug may not show on certain monitors.
For instance, the only reason this bug was visible on my ASUS PB238
monitor was due to the fact that this monitor using the enhanced framing
symbol sequence, the flag for which is ignored if the radeon driver
thinks that the DisplayPort version is below 1.1.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
No need to try to call ttm_bo_device_release twice during module unload.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
When a user-space process writes directly to the fbdev framebuffer,
we hit a circular locking dependency. Fix this by introducing a local
delayed work callback so that the defio lock can be released before
calling into the modesetting code for a dirty update.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
It appears some MST docks are worse than other, but the only
way to know is to see the sw revisions in here, so dump
the branch OUI so we can look at the sw revision.
v2: Thierry made me feel guilty, so I parsed the branch
OUI.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Revert of a VBT parsing commit that should've been queued for drm-next,
not v4.2. The revert unbreaks Braswell among other things.
Also on Braswell removal of DP HBR2/TP3 and intermediate eDP frequency
support. The code was optimistically added based on incorrect
documentation; the platform does not support them. These are cc: stable.
Finally a gpu state fix from Chris, also cc: stable.
* tag 'drm-intel-fixes-2015-08-20' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Avoid TP3 on CHV
drm/i915: remove HBR2 from chv supported list
Revert "drm/i915: Add eDP intermediate frequencies for CHV"
Revert "drm/i915: Allow parsing of variable size child device entries from VBT"
drm/i915: Flag the execlists context object as dirty after every use
Stop double freeing the the BO list by pulling the content
of amdgpu_cs_parser_prepare_job() into the IOCTL function again.
v2: better commit message
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com> (v1)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The problem now is that we don't necessarily call amdgpu_ib_get()
in some error paths and so work with uninitialized data.
Better require that the memory is already zeroed.
v2: better commit message
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com> (v1)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
More appropriate and fixes some nasty lockdep warnings.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Used by mesa, etc. for profiling.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch add support for Two Dimensional Animation and Compositing
Engine (2D-ACE) on the Freescale SoCs.
2D-ACE is a Freescale display controller. 2D-ACE describes
the functionality of the module extremely well its name is a value
that cannot be used as a token in programming languages.
Instead the valid token "DCU" is used to tag the register names and
function names.
The Display Controller Unit (DCU) module is a system master that
fetches graphics stored in internal or external memory and displays
them on a TFT LCD panel. A wide range of panel sizes is supported
and the timing of the interface signals is highly configurable.
Graphics are read directly from memory and then blended in real-time,
which allows for dynamic content creation with minimal CPU
intervention.
The features:
(1) Full RGB888 output to TFT LCD panel.
(2) Blending of each pixel using up to 4 source layers
dependent
on size of panel.
(3) Each graphic layer can be placed with one pixel resolution
in either axis.
(4) Each graphic layer support RGB565 and RGB888 direct colors
without alpha channel and BGRA8888 BGRA4444 ARGB1555 direct
colors
with an alpha channel and YUV422 format.
(5) Each graphic layer support alpha blending with 8-bit
resolution.
This is a simplified version, only one primary plane, one
framebuffer, one crtc, one connector and one encoder for TFT
LCD panel.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The following PR add support for 3 more atmel SoCs and for some missing
features (new input formats and PRIME support).
* 'drm-atmel-hlcdc-devel' of https://github.com/bbrezillon/linux-at91:
drm: atmel-hlcdc: add support for sama5d4 SoCs
drm: atmel-hlcdc: add support for at91sam9n12 SoC
drm: atmel-hlcdc: add support for at91sam9x5 SoCs
drm: atmel-hlcdc: add RGB565 and RGB444 output support
drm: atmel-hlcdc: add the missing DRM_ATOMIC flag
drm: atmel-hlcdc: add PRIME support
This patch removes TP3 support on CHV since there is no support
for HBR2 on this platform.
v2: rename the function to indicate it checks source rates (Jani)
v3: update comment to indicate TP3 dependency on HBR2 supported
hardware (Jani)
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[Jani: fixed a couple of checkpatch warnings.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch removes 5.4Gbps from supported link rate for CHV since
it is not supported in it.
v2: change the ordering for better readability (Ville)
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts
commit fe51bfb95c.
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Mar 12 17:10:38 2015 +0200
CHV does not support intermediate frequencies so reverting the
patch that added it in the first place
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This reverts
commit 047fe6e6db
Author: David Weinehall <david.weinehall@linux.intel.com>
Date: Tue Aug 4 16:55:52 2015 +0300
drm/i915: Allow parsing of variable size child device entries from VBT
That commit is not valid for v4.2, however it will be valid for v4.3. It
was simply queued too early.
The referenced regressing commit is just fine until the size of struct
common_child_dev_config changes, and that won't happen until
v4.3. Indeed, the expected size checks here rely on the increased size
of the struct, breaking new platforms.
Fixes: 047fe6e6db ("drm/i915: Allow parsing of variable size child device entries from VBT")
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
I2CM_ADDRESS became a MESS, fix it, also change guarding define
to __DW_HDMI_H__ , since the driver is not IMX specific.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dw_hdmi enable/disable handling is particularly weak in several
regards:
* The hotplug interrupt could call hdmi_poweron() or hdmi_poweroff()
while DRM is setting a mode, which could race with a mode being set.
* Hotplug will always re-enable the phy whenever it detects an active
hotplug signal, even if DRM has disabled the output.
Resolve all of these by introducing a mutex to prevent races, and a
state-tracking bool so we know whether DRM wishes the output to be
enabled. We choose to use our own mutex rather than ->struct_mutex
so that we can still process interrupts in a timely fashion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi_phy_enable_power() is not about enabling and disabling power.
It is about allowing or preventing power-down mode being entered - the
register is documented as "Power-down enable (active low 0b)."
This can be seen as the bit has no effect when the HDMI phy is
operational on iMX6 hardware.
Rename the function to dw_hdmi_phy_enable_powerdown() to reflect the
documentation, make it take a bool for the 'enable' argument, and invert
the value to be written.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a mode set, DRM makes the following sequence of calls:
* for_each_encoder
* bridge mode_fixup
* encoder mode_fixup
* crtc mode_fixup
* for_each_encoder
* bridge disable
* encoder prepare
* bridge post_disable
* disable unused encoders
* crtc prepare
* crtc mode_set
* for_each_encoder
* encoder mode_set
* bridge mode_set
* crtc commit
* for_each_encoder
* bridge pre_enable
* encoder commit
* bridge enable
dw_hdmi enables the HDMI output in both the bridge mode_set() and also
the bridge enable() step. This is duplicated work - we can avoid the
setup in mode_set() and just do it in the enable() stage. This
simplifies the code a little.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only enable audio support if the sink supports audio in some form, as
defined via its EDID. We discover this capability using the generic
drm_detect_monitor_audio() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The FSL kernel detects the HDMI vendor id, and uses this to set
hdmi->edid_cfg.hdmi_cap, which is then used to set mdvi appropriately,
rather than detecting whether we are outputting a CEA mode. Update
the dw_hdmi code to use this logic, but lets eliminate the mdvi
variable, prefering the more verbose "hdmi->sink_is_hdmi" instead.
Use the generic drm_detect_hdmi_monitor() to detect a HDMI sink.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in the previous commit, the dw-hdmi driver does not support
pixel doubled modes at present; it does not configure the PLL correctly
for these modes. Therefore, filter out the double-clocked modes as we
presently are unable to support them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi sets a pixel repetition factor of 1 for VICs 10-15, 25-30 and
35-38. However, DRM uses their native resolutions in its timing
information. For example, VIC 14 can be 1440x480 with no repetition,
or 720x480 with one pixel repetition. As DRM uses 1440 pixels per line
for this video mode, we need no pixel repetition.
In any case, pixel repetition appears broken in dw_hdmi.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the struct hdmi_vmode mhsyncpolarity/mvsyncpolarity/minterlaced
members, which are only used within a single function. We can directly
reference the appropriate mode->flags instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Describe capabilities of the HLCDC IP found on sama5d4 SoCs and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Describe capabilities of the HLCDC IP found on at91sam9n12 SoC and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Describe capabilities of the HLCDC IP found on at91sam9x5 SoCs and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The atmel-hlcdc driver already supports atomic operations, add the
missing DRM_ATOMIC flag to expose the atomic features to userspace.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If PM is enabled but PM_SLEEP is disabled, the suspend/resume functions
are still unused and produce a compiler warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 4.1+
Pagetables can be moved and therefore the page directory update can be necessary
for the current cs even if none of the the bo's are moved. In that scenario
there is no fence between the sdma0 and gfx ring, so we add one.
v2 (chk): rebased
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Explicitly select BACKLIGHT_LCD_SUPPORT to satisfy the direct dependency
of BACKLIGHT_CLASS_DEVICE.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Explicitly select BACKLIGHT_LCD_SUPPORT to satisfy the direct dependency
of BACKLIGHT_CLASS_DEVICE.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rework run queue implementation, especially remove the odd list handling.
v2: cleanup the code only, no algorithem change.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
fix the bug that there is duplicated bo_update_mapping issued
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
bo_list_clone() will take a lot of time when bo_list hold too much
elements, like above 7000
Signed-off-by: Monk.Liu <monk.liu@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
It's not validated yet and causes more harm than good.
Avoids spurious resets.
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
remaining timeout returned by amdgpu_fence_wait_any can be larger than
max int value, thus the truncated 32 bit value in r ends up being
negative while its original long value is positive.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
fix fence is released when pass to **fence sometimes.
add reference for it.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-and-Reviewed-by: Leo Liu <leo.liu@amd.com>
Not used any more.
v2: remove amd_sched_emit as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Similar to radeon, except that amdgpu doesn't even use struct_mutex to
protect anything like the shared z buffer (sane gpu architecture,
yay!). And the code already grabs the globa adev->ring_lock, so this
code can't race with itself. Which makes struct_mutex completely
redundnant. Remove it.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It really doesn't protect anything which doesn't have other locks
already. Also this is run from driver unload code so not much need for
locks anyway.
Same changes as for radeon really.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We already grab 2 device-global locks (write-sema rdev->pm.mclk_lock
and rdev->ring_lock), adding another global mutex won't serialize this
code more. And since there's really nothing interesting that gets
protected in radeon by dev->struct mutex (we only have the global z
buffer owners and it's still serializing gem bo destruction in the drm
core - which is irrelevant since radeon uses ttm anyway internally)
this doesn't add protection. Remove it.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It really doesn't protect anything which doesn't have other locks
already. Also this is run from driver unload code so not much need for
locks anyway.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The workaround simply doesn't work because VM mappings
are controlled by userspace not the kernel.
Additional to that this is just a performance problem
which happens if you have holes in your VM mapping.
v2: adjust virtual addr alignment as well.
v3: fix trivial warning
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com> (v1)
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com> (v2)
Looks like that somehow got missed while during porting the radeon changes.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It was just a wrapper for fence_wait anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The common kernel function does the same thing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
scheduler fence is based on kernel fence framework.
v2: squash in Christian's build fix
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
v2: rebased
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Avoiding a couple of casts.
v2: rename c_entity to entity as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Cleanup the kernel context handling.
v2: rebased
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com> (v1)
Id's are for the IOCTL ABI only.
v2: remove tgid as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
We didn't initialized the mutex in the cloned bo list resulting in nice
warnings from lockdep. Also fixes error handling in this function.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This way can avoid interrupt lost, and can process sched job exactly.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
This function is used to get the next queued sequence number
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This function is to update last_emitted_v_seq and wake up the waiters.
It should be called by driver in the run_job backend function
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It is clean to update last_queued_v_seq in the scheduler module
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Fix the code alignment, etc.
v2: rebase the code
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
every sbumission should be able to get a fence.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
It is theoretically possible that a swapped out BO gets the
same GTT address, but different backing pages while being swapped in.
Instead just use another VA state to note updated areas.
Ported from not upstream yet radeon commit with the same name.
v2: fix some bugs in the original implementation found in the radeon code.
v3: squash in VCE/UVD fix
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
thus unnecessary wake up could be avoid between rings
v2:
move wait_queue_head to fence_drv from ring
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
origninal method will sleep/schedule at the granurarity of HZ/2 and
based on seq signal method, the new implement is based on kernel fance
interface, no unnecessary schedule at all
v2: replace logic of original amdgpu_fence_wait_any
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
if enabling scheduler, then the queued seq is assigned
when pushing job before emitting job.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
the job must be emitted by scheduler, otherwise scheduler is abnormal.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
This option can be used to specify the max number of submissions in the
active HW queue. The default value is 2 now.
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This option can be used to specify the max job number in the job queue,
and it is 16 by default.
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
it is possible that the callback isn't defined sometimes.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
fence_process may be called from kthread, user thread and interrupt context.
it is possible to called concurrently, then will wake up fence queue multiple times.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
use kernel context to submit command for vm
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
user mode will still use pte ring as a normal ring.
if the prepare job generates another command(update pte) on its ring in scheduler,
then will kill scheduler which is going to waiting later job but pending running job.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
BO validation is moved to scheduler except usrptr which must be validated
in user process
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
run queue:
A set of entities scheduling commands for the same ring. It
implements the scheduling policy that selects the next entity to
emit commands from.
entity:
A scheduler entity is a wrapper around a job queue or a group of
other entities. This can be used to build hierarchies of entities.
For example all job queue entities belonging to the same process
may be placed in a higher level entity and scheduled against other
process entities.
Entities take turns emitting jobs from their job queue to the
corresponding hardware ring, in accordance with the scheduler policy.
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Acked-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
v2: agd5f: fix the rb setup.
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
v2: agd5f: fix up XDMA golden settings
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
v2: agd5f: prepare for release
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
v2: agd5f: prepare for release
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
use kmalloc_array instead of kcalloc where appropriate and other
cleanups.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Make the definitions common for all driver components
v2: fix kfd
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Add GPU family definitions and timeout value for IP components.
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Feel free to suggest more.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
the definitions can be shared by different IP components.
v2: fix include path
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
We need to return the sequence number to userspace
even when we don't use user fences.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This makes assigning VM IDs independent from the use of VM IDs.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
v2 (chk): split fix from original patch
Signed-off-by: monk.liu <monk.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Otherwise the first 16 fences of a context will always signal immediately.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
It's not used any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This is a prerequisite for the GPU scheduler to make the order
of submission independent from the order of execution.
v2: properly implement the locking
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This also requires some error handling from the callers of that function.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
The comment is misleading and incorrect, remove it.
Printing the id is completely meaningless and this practice
can cause a race conditions on command submission.
The flags and hangs fields are completely unused.
Give all fields a common indentation.
v2: remove fpriv reference and unused flags as well, fix debug message.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This new interface can be used by IP components to retrieve the
firmware information from the core driver.
v2: fix one typo
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhou@amd.com>
Signed-off-by: Young Yang <Young.Yang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This implements the interface for atombios command
and data table access.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CGS (Common Graphics Services) is an AMD cross component
abstraction layer to designed to better encapsulate
specific IP block drivers so different teams can effectively
work on differnet IP block drivers independently. It provides
a common interface for things like accessing registers,
allocating GPU memory, and registering interrupt sources.
The plan is to eventually move more and more IP drivers to
this interface. The first user is the ACP IP driver.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In function 'amdgpu_uvd_cs_pass2':
warning: 'min_ctx_size' may be used uninitialized in this function
buf_sizes[0x4] = min_ctx_size;
^
note: 'min_ctx_size' was declared here
unsigned image_size, tmp, min_dpb_size, num_dpb_buffer, min_ctx_size;
^
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Everytime we use the logical context with execlists it becomes dirty (as
the hardware will write the new register values afterwards, as well as
the GPU state that will be used). We need to then flag the context as
dirty everytime since after a swap-out/swap-in cycle the dirty flag will
be cleared, and a further swap-out cycle will then loose the most recent
GPU state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
A couple of fixes from the previous pull request as well as gl3 support.
There is one drm core change, an export of a previously private function.
Take 2 implementing screen targets, this time with the fbdev code adjusted
accordingly.
Also there is an implementation of register-driven command buffers, that
overrides the FIFO ring for command processing. It's needed for our upcoming
hardware revision.
* 'vmwgfx-next' of git://people.freedesktop.org/~thomash/linux: (35 commits)
drm/vmwgfx: Fix copyright headers
drm/vmwgfx: Add DX query support. Various fixes.
drm/vmwgfx: Add command parser support for a couple of DX commands
drm/vmwgfx: Command parser fixes for DX
drm/vmwgfx: Initial DX support
drm/vmwgfx: Update device includes for DX device functionality
drm: export the DRM permission check code
drm/vmwgfx: Fix crash when unloading vmwgfx v2
drm/vmwgfx: Fix framebuffer creation on older hardware
drm/vmwgfx: Fixed topology boundary checking for Screen Targets
drm/vmwgfx: Fix an uninitialized value
drm/vmwgfx: Fix compiler warning with 32-bit dma_addr_t
drm/vmwgfx: Kill a bunch of sparse warnings
drm/vmwgfx: Fix kms preferred mode sorting
drm/vmwgfx: Reinstate the legacy display system dirty callback
drm/vmwgfx: Implement fbdev on kms v2
drm/vmwgfx: Add a kernel interface to create a framebuffer v2
drm/vmwgfx: Avoid cmdbuf alloc sleeping if !TASK_RUNNING
drm/vmwgfx: Convert screen targets to new helpers v3
drm/vmwgfx: Convert screen objects to the new helpers
...
This introduces support for a couple of new panels and also contains
some work to restructure the directories to get more consistency, to
deal better with more panel and bridge drivers getting added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Dee7
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.3-rc1
This introduces support for a couple of new panels and also contains
some work to restructure the directories to get more consistency, to
deal better with more panel and bridge drivers getting added.
* tag 'drm/panel/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/bridge: Put Kconfig entries in a separate menu
drm/panel: Add support for LG LG4573 480x800 4.3" panel
drm/panel: Add display timing for Okaya RS800480T-7X0GP
of: Add Okaya Electric America vendor prefix
drm/panel: simple: Add support for NEC NL4827HC19-05B 480x272 panel
drm/panel: simple: Add support for AUO B080UAN01
drm/panel: simple: Correct minimum hsync length of the HannStar HSD070PWW1 panel
drm/panel: simple: Add bus format for HannStar HSD070PWW1 LVDS panel
drm/bridge: Add vendor prefixes
drm/panel: Add Samsung prefix to panel drivers
drm/exynos: Remove PTN3460 dependency
There are a bunch of non-critical fixes here that I've collected over
the past few months, but the biggest part is Tegra210 support, in the
DC, DSI and SOR/HDMI drivers.
Also this finally restores DPMS with atomic mode-setting, something
that has been broken since the conversion and which I had originally
expected to take far less longer to fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJVzgFhAAoJEN0jrNd/PrOhBLAP/2vDyK8H52ZusDdh06GNnmSB
hr3Dfa3tePWUH/Um5qSPUvzdJg8Pnz85LsYUuQuHQRLeXfk2IsDe284CpMcKt6pW
YQPXYqQreKwZFgct2fjqohlqRjNP6qRWuPYsTciz0IMiSFyEJY9DBuYhQQbD+HHb
9CJsHNUl2Oi3jOORvuawJKIyDPFfh4JzPRGcfdGRSE1VE6qt5Cb6XVcQxwR6R6UW
7NlOg0ylYcSkC1PpDTSIpTdpksxNJI0I4k263UlYQ9sfmHQjX1N3Ef/s1DOm4vHf
1CWJlT0zI8BVerukMe2rDkyzsXJgVN5QphQzwnRz7AhEtXtFNUKoRP6mIsCjYxRp
3HTQI4rOF2VbHw2yDSOTl9SBrq94dOtkZ3YskvHQICjcO6P/602ZqFrLjFj/jn6n
rMNXoioYi8u3DDGsCdutiQTh+7BiQx9Mk/vVOei0vEeUk5KefGSawMwjo1Djjknb
aagRpVHAbTZV178RO8tMGB10Z2aiYdYp/K7sywK4ktkhlYUGpIH6kmPwY/bERPes
dZMqABSG8AslKZYrZhXWcXBPq5ymGojcJ0mqD7rK8xk1hAsE1LbMHqVwfrMCOaue
r4bnhjnBkjcSXa+Pwz/5OvdbmLjXxmWMGIes1DYYgsWaIBvPfTMCzMv7Cq6f6A9X
7zCHroPgA/APxrk3b4Dc
=lxYn
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.3-rc1
There are a bunch of non-critical fixes here that I've collected over
the past few months, but the biggest part is Tegra210 support, in the
DC, DSI and SOR/HDMI drivers.
Also this finally restores DPMS with atomic mode-setting, something
that has been broken since the conversion and which I had originally
expected to take far less longer to fix.
* tag 'drm/tegra/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux: (41 commits)
drm/tegra: sor: Add HDMI support
drm/tegra: sor: Add Tegra210 eDP support
drm/tegra: dc: Implement atomic DPMS
drm/tegra: sor: Restore DPMS
drm/tegra: dsi: Restore DPMS
drm/tegra: hdmi: Restore DPMS
drm/tegra: rgb: Restore DPMS
drm/tegra: sor: Use DRM debugfs infrastructure for CRC
drm/tegra: sor: Write correct head state registers
drm/tegra: sor: Constify display mode
drm/tegra: sor: Reset the correct debugfs fields
drm/tegra: sor: Set minor after debugfs initialization
drm/tegra: sor: Provide error messages in probe
drm/tegra: sor: Rename registers for consistency
drm/tegra: dpaux: Disable interrupt when detached
drm/tegra: dpaux: Configure pads as I2C by default
drm/tegra: dpaux: Provide error message in probe
drm/tegra: dsi: Add Tegra210 support
drm/tegra: dsi: Add Tegra132 support
drm/tegra: dsi: Add Tegra124 support
...
Summary:
- Clean up HDMI and MIXER parts
- Clean up legacy structures specific to Exynos DRM
. This patch series removes existing exyons_drm_display and
exynos_drm_encoder structures specific to Exynos DRM, and
makes them to replace with common drm_encoder structure.
With cleanup patch, we removes exynos_drm_encoder module.
- Clean up gem, dmabuf and buffer modules
. This patch series replaces existing Exynos DRM dmabuf codes
with common drm prime ones, and embeds all codes of exynos_drm_buf
into exynos_drm_gem module.
With cleanup patch, we removes exynos_drm_buf and exynos_drm_dmabuf
modules.
- And some fixups.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: (53 commits)
drm/exynos: merge exynos_drm_buf.c to exynos_drm_gem.c
drm/exynos: use prime helpers
drm/exynos: remove function roundup_gem_size
drm/exynos: remove function update_vm_cache_attr
drm/exynos: remove function check_gem_flags
drm/exynos: use ERR_PTR instead of NULL in exynos_drm_gem_init
drm/exynos: remove unused fields of struct exynos_drm_gem_buf
drm/exynos: stop copying sg table
drm/exynos: remove function exynos_drm_gem_map_buf
drm/exynos: remove mutex locking in pagefault handler
drm/exynos: remove function convert_to_vm_err_msg
drm/exynos: stop using sgtable in page fault handler
drm/exynos: remove struct exynos_drm_encoder layer
drm/exynos: fold encoder setup into exynos_drm_load()
drm/exynos: remove exynos_drm_create_enc_conn()
drm/exynos: remove exynos_encoder's .commit() op
drm/exynos: remove extra call to exynos_dp_commit()
drm/exynos: remove extra call to hdmi_commit()
drm/exynos: remove struct exynos_drm_display
drm/exynos: simplify calculation of possible CRTCs
...
1) includes all the drm/msm side of things for upstream kernel working
on dragonboard 410c (still some pending work on adv7533 bridge chip)
2) initial support for msm8x94 (snapdragon 810)
3) support for msm8x74v1 (in addition to existing v2 support)
4) support for dma planes on mdp5 (additional planes that cannot scale/csc)
5) more yuv format support for mdp5 (single plane vyuy/uyvy/yuyv/yvyu,
two plane nv16/nv61, and three plane yuv420/yvu420)
6) rotation support for mdp5
7) initial hdcp support
8) fixes, etc
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (46 commits)
drm/msm/dsi: Introduce DSI configuration module
drm/msm/dsi: Make each PHY type compilation independent
drm/msm/dsi: Split PHY drivers to separate files
drm/msm/dsi: Return void from msm_dsi_phy_disable()
drm/msm/dsi: Specify bitmask to set source PLL
drm/msm/mdp: Clear pending interrupt status before enable interrupt
drm/msm/mdp5: Add rotation (hflip/vflip) support to MDP5 planes (v2)
drm/msm: add calls to prepare and unprepare panel
drm/msm/dsi: Modify dsi manager bridge ops to work with external bridges
drm/msm/dsi: Allow dsi to connect to an external bridge
drm/msm/dsi: Create a helper to check if there is a connected device
drm/msm/dsi: Refer to connected device as 'device' instead of 'panel'
drm/msm/dsi: Make TE gpio optional
drm/msm: mdp4 lvds: get panel node via of graph parsing
drm/msm: dsi host: Use device graph parsing to parse connected panel
drm/msm: dsi host: add missing of_node_put()
drm/msm: Enable clocks during enable/disable_vblank() callbacks
drm/msm/mdp5: Add support for msm8x74v1
drm/msm/mdp5: Add DMA pipe planes for MDP5
drm/msm/mdp: Add capabilities to MDP planes (v2)
...
Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
Convert g2d_userptr_get_dma_addr() to pin pages using get_vaddr_frames().
This removes the knowledge about vmas and mmap_sem locking from exynos
driver. Also it fixes a problem that the function has been mapping user
provided address without holding mmap_sem.
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct exynos_drm_gem_obj can have fields of the struct
exynos_drm_gem_buf then don't need to use exynos_drm_buf.c file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The dma-buf codes of exynos drm is almost same with prime helpers. A
difference is that consider DMA_NONE when import dma-buf, but it's wrong
and we don't consider it any more, so we can use prime interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function roundup_gem_size can be merged in exynos_drm_gem_create.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function update_vm_cache_attr can be merged in exynos_drm_gem_mmap.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function check_gem_flags is too simple, so it's better to move codes
in each consumer functions.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The userptr, write and pfnmap of struct exynos_drm_gem_buf are not used
anywhere.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already struct exynos_drm_gem_buf has pages of the buffer, so we don't
need to copy from sg table of the buffer to sg table of dma-buf
attachment, just can make sg table from pages of the buffer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The exynos_drm_gem_map_buf can be merged in exynos_drm_gem_fault.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no reason to use mutex locking in pagefault handler.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The convert_to_vm_err_msg is called just once by exynos_drm_gem_fault,
so it's simple not to use the function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already struct exynos_drm_gem_buf has pages of the buffer when buffer is
created, so just can use pages in page fault handler, we don't have to
make sgtable of the buffer. But this needs to construct pages of the
buffer that is imported from dma-buf prime.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
struct exynos_drm_encoder was justing wrapping struct drm_encoder, it had
only a drm_encoder member and the internal exynos_drm_encoders ops that
was directly mapped to the drm_encoder helper funcs.
So now exynos DRM uses struct drm_encoder directly, this removes
completely the struct exynos_drm_encoder.
v2: add empty .mode_fixup() and .mode_set() to DSI and DPI to avoid null
pointer.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
As we are removing the exynos encoder move the encoder setup operation
directly inside the exynos_drm_load()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This functions was just hiding the encoder and connector creation in
a way that was less clean than if we get rid of it. For example,
exynos_encoder ops had .create_connector() defined only because we were
handing off the encoder and connector creation to
exynos_drm_create_enc_conn(). Without this function we can directly call
the create_connector function internally in the code, without the need of
any vtable access.
It also does some refactoring in the code like creating a bind function
for dpi devices.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
.commit() is not used anymore, Exynos encoders now follow the
.enable()/.disable() semantics from drm atomic core, so remove this
callback.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
exynos_dp_commit() was getting called twice by exynos encoder core, once
inside the .enable() call and another time by .commit() itself.
The remove of the second call caused the wake of a bug, the operations
orders inside exynos_dp_commit was wrong and we had to move
exynos_dp_start_video() to be the last operation in there.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
hdmi_commit() was getting called twice by exynos encoder core, once inside
the .enable() call and another time by .commit() itself.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This struct was just representing encoder information, it was a member of
struct exynos_drm_encoder, so any code trying to access encoder data would
have to go through the encoder struct, get the display struct and then get
the data it want.
During this patchset we also realized that the only data
exynos_drm_encoder needs to store is the drm_encoder parent and the
exynos_drm_encoder_ops.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All CRTCs can only be LCD, HDMI or VIDI, so basically all CRTCs will be a
possible CRTCs. This patch removes an extra function with switch that was
only checking if the CRTC type was one of those three above.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
These two display_ops are not used anywhere, remove them.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
phy_power_on() and phy_power_off() already checks for NULL pointer.
This patch removes the wrappers exynos_dp_phy_init() and
exynos_dp_phy_exit() since the only think they were doing was a check for
NULL phy.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The DRM Core doesn't have a dpms() operation anymore, everything
now is enable() or disable().
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Instead of blindly ignore the return value of enable_vblank return it
to the upper DRM layer for error handling.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Rename crtc_{widht,height} to crtc_{w,h} and src_{width,height} to
src_{w,h} to make it similar to the atomic state names.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Now after the move to use drm_plane_state directly struct drm_plane_state
has many unused fields, along with others that weren't used before the
plane state change. Thus remove them all.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
For some fields the use of struct exynos_drm_plane filled with data from
the plane state just creates a source of duplicated information and
overhead. Here we change the crtc drivers to access the plane state
directly simplifying the code by not relying on a exynos internal struct.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We already have the plane pointer in before calling .update_plane() or
disable_plane() so pass it directly to those calls avoiding a new
conversion from zpos to struct exynos_drm_plane.
v2: don't remove check for suspended in FIMD (comment by Joonyoung)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The same check is placed twice in fimd/decon_update_plane(), remove
one of them.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Get rid of legacy DRM vblank function that are less clear to use.
The new ones basically requires only the crtc as parameters.
It also clean ups exynos_drm_crtc_finish_pageflip() parameters as a
consequence.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Instead of giving -1 to as arg to drm_send_vblank_event() pass the
correct pipe number to it.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This is simplest solution about reported problem[1]. It's no problem to
clear channel only when iommu is enabled, if we consider that we cannot
recognize iommu errors when iommu is disabled and it have been valid
until now. But this cannot be nice solution.
[1] https://lkml.org/lkml/2015/7/21/404
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already drm_iommu_attach_device checks whether support iommu internally.
It should clear channels always regardless iommu support. We didn't know
because we can detect the problem when iommu is enabled, so we don't
have to use drm_iommu_attach_device_if_possible and then we can remove
drm_iommu_attach_device_if_possible and clear_channels function pointer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The vidi is virtual kms driver and now it is registered earlier than
actual hw kms drivers, so it will occupy crtc index 0. Some users
assume the condition yet that actual hw kms driver has crtc index 0.
It may or may not be matter but let's arrange register order.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Driver uses only VSYNC interrupts, so we need to cache VSYNC bit state only.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The driver uses bool protected by mutex to track power state.
The patch replaces this combo with single bit and atomic bitops.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already drm_iommu_attach_device and drm_iommu_detach_device check
whether support iommu internally, so we don't have to call
is_drm_iommu_supported before call them.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
If CONFIG_ARM_DMA_USE_IOMMU is disable, CONFIG_DRM_EXYNOS_IOMMU also is
disable. When CONFIG_DRM_EXYNOS_IOMMU is disable,
is_drm_iommu_supported() returns always false, so we can remove to use
ifdef CONFIG_ARM_DMA_USE_IOMMU in is_drm_iommu_supported().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The unique results of all the combination of rotation and flip can
be represented by just 8 states. This patch handles all the combination
correctly.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch removes intermediate struct for HDMIv14 register configuration,
instead registry values are calculated on the fly.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch removes intermediate struct for HDMIv13 register configuration,
instead registry values are calculated on the fly.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch removes redundant fields from hdmi_conf_regs. Their values
can be calculated from current_mode. This patch is the first step to remove
whole hdmi_conf_regs structure.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch replaces duplicated driver data fields in private context with
pointer to driver data. It also simplifies driver data lookup code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Most of the code is called by drm core framework, so it is already synchronized.
The only async function is irq routine which only calls drm framework so it
does not need to be synchronized.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
GPIO is tested only in hdmi_detect, so there is no reason to set it in
other places and to preserve its value in context.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
s5p_hdmi_platform_data were used before device tree introduction.
As HDMI driver is DT only we can drop this struct completely.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Once pm_runtime_set_active() gets called, the kernel assumes that given
device has already enabled runtime pm and will call pm_runtime_suspend()
without matching pm_runtime_resume(). In case of DRM FIMC IPP driver,
this will result in calling clk_disable() without respective call to
clk_enable(). This patch removes call to pm_runtime_set_active() to
ensure that pm_runtime_suspend/resume calls will match.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
INT_EN cache field was updated only by mixer_enable_vblank.
The patch adds update also by mixer_disable_vblank function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The driver used incorrect flags to clear interrupt status.
The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
edid returned by drm_get_edid should be freed.
The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The bits for rotation are not used as exclusively. So GSC_IN_ROT_270 can
not be used for swap detection. The definition of it is same with
GSC_IN_ROT_MASK. It is enough to check GSC_IN_ROT_90 bit is set or not to
check whether width / height size swapping is needed.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
With more platforms supported, the DSI host
configuration array keeps expanding. This change
moves those to a separate dsi_cfg module.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
On a certain platform, only one type of DSI PHY is used.
This change allows the user to only compile the PHY type
which is being used.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change moves each PHY type specific code into
separate files.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We are not checking the return value from msm_dsi_phy_disable().
Change the return type to void.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The bit position to configure source PLL will change
on new types of PHYs. The caller should pass down
this information.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pending interrupt status needs to be cleared before enable the
interrupt. Otherwise it's possible to get a pending interrupt instead
of an incoming interrupt.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 SSPPs can flip the input source horizontally or vertically.
This change is to add this support to MDP5 planes.
v1: Initial change
v2: Use existing "rotation" property instead of creating msm specific
properties. In order to be compatiable with legacy non-atomic
set_property, switch to drm_atomic_helper_plane_set_property
helper function.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Prepare the panel before it's enabled and un-prepare after disable, this
will make sure that the regulators are switched on and off correctly.
Tested it on APQ8064 based IFC6410 with panel.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi bridge ops call drm_panel functions to set up the connected
drm_panel. Add checks to make sure these aren't called when we're
connected to an external bridge.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are platforms where the DSI output can be connected to another
encoder bridge chip (DSI to HDMI, DSI to LVDS etc).
Add support for external bridge support to the dsi driver. We assume that
the external bridge chip would be of the type drm_bridge. The dsi driver's
internal drm_bridge (msm_dsi->bridge) is linked to the external bridge's
drm_bridge struct.
In the case we're connected to an external bridge, we don't need to create
and manage a connector within our driver, it's the bridge driver's
responsibility to create one.
v2:
- Move the external bridge attaching stuff to dsi manager to make things
cleaner.
- Force the bridge to connect to a video mode encoder for now (the dsi
mode flags may have not been populated by modeset_init)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a helper msm_dsi_device_connected() which checks whether we have a
device connected to the dsi host or not. This check gets messy when we
have support external bridges too. Having an inline function makes it
more legible.
For now, the check only consists of msm_dsi->panel being non-NULL. Later,
this will check if we have an external bridge or not.
This helper isn't used in dsi_connector related code as that's specific
to only when a drm_panel is connected.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently support only panels connected to dsi output. We're going to
also support external bridge chips now.
Change 'panel_node' to 'device_node' in the struct msm_dsi_host and
'panel_flags' to 'device_flags' in msm_dsi. This makes things sound a
bit more generic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Platforms containing only DSI video mode devices don't need a TE gpio.
Make TE gpio optional.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently get the output connected to LVDS by looking for a phandle
called 'qcom,lvds-panel' under the mdp DT node.
Use the more standard of_graph approach to create an lvds output port,
and retrieve the panel node from the port's endpoint data.
v3
- Fix return value checks of of_graph_* calls.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi host looks for the connected panel node by parsing for a child
named 'panel'. This hierarchy isn't very flexible. The connected
panel is forced to be a child to the dsi host, and hence, a mipi dsi
device. This isn't suitable for dsi devices that don't use mipi dsi
as their control bus.
Follow the of_graph approach of creating ports and endpoints to
represent the connections between the dsi host and the panel connected
to it. In our case, the dsi host will only have one output port, linked
to the panel's input port.
Update DT binding documentation with device graph usage info.
v3:
- Fix return value checks of of_graph_* calls.
- Don't make port a mandatory DT property
- Fix defer check when no panel node specified
- Rename parse_dt func to align with other dsi_host funcs
Reviewed-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Decrement device node refcount if of_get_child_by_name is successfully
called.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
AHB clock should be enabled before accessing registers during
enable/disable_vblank(). Since these 2 callbacks are called in
atomic context while clk_prepare may cause thread sleep, a work
is scheduled to control vblanks.
v2: fixup spinlock initialization
Signed-off-by: Hai Li <hali@codeaurora.org>
[add comment about cancel_work_sync() before drm_irq_uninstall()]
Signed-off-by: Rob Clark <robdclark@gmail.com>
msm8x74v1 has different MDP5 version (v1.0) from msm8x74v2 (v1.2).
Add a separate config data to support msm8x74v1.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to add planes which use DMA pipes for MDP5.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
[slight comment adjust to s/Construct public planes/Construct video
planes/ since DMA planes are public planes too, they just can't scale
or CSC]
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP planes can be implemented using different type of HW pipes,
RGB/VIG/DMA pipes for MDP5 and RGB/VG/DMA pipes for MDP4. Each type
of pipe has different HW capabilities such as scaling, color space
conversion, decimation... Add a variable in plane data structure
to specify the difference of each plane which comes from mdp5_cfg data
and use it to differenciate the plane operation.
V1: Initial change
V2: Fix a typo in mdp4_kms.h
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add packed YUV422 and planar YUV420 formats to MDP supported
formats.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Newer MDP5 uses 2 shared memory pool clients for certain YUV formats.
For example, if VIG0 is used to fetch data in YUYV format, it will use
VIG0_Y for Y component, and VIG0_Cr for UV packed.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
[rebase]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
This makes it easy to determine if a format is YUV. The old
method of using chroma sample type incorrectly marks YUV444 as
RGB format.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
[rebase]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reset DSI PHY silently changes its PLL registers to reset status,
which will make cached status in clock driver invalid and result
in wrong output rate of link clocks. The current restore mechanism
in DSI PLL does not cover all the cases. This change is to recover
PLL status after PHY reset to match HW status with cached status
in clock driver.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi_destroy() function was called in two cases by the dsi_init() function
during error handling even if the passed variable contained a null pointer.
* This implementation detail could be improved by adjustments for jump
targets according to the Linux coding style convention.
* Drop an unnecessary initialisation for the variable "msm_dsi" then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[add couple missing ERR_PTR()'s]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi_destroy() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change takes advantage of a HW feature that synchronize
flush operation on CTL1 to CTL0, to keep dual DSI pipes in
sync.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In MDP5, CTL contains information of the whole pipeline whose
output goes down to a display interface. In various cases, one
interface may require 2 CRTCs, but only one CTL. Some interfaces
also require to use certain CTLs.
Instead of allocating CTL for each active CRTC, this change is to
associate a CTL with each interface.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to add properties alpha/zpos/blend_mode to mdp5 plane
for alpha blending operation to generate the blended output.
v1: Initial change
v2: Change "premultilied" property to enum (Rob's comment)
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
[Don't actually expose alpha/premultiplied props to userspace yet
pending a chance for discussion and some userspace to exercise it]
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was a hold-over from the pre-atomic days and legacy userspace that
only understood CRTCs. Fortunately we don't have any properties, so
this doesn't change anything. But before we start growing some plane
properties, we should fix this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY errors are falsely reported whenever a dsi error occurs. This is
because DSI_DLN0_PHY_ERR isn't only used as a status register, but also
used to mask PHY errors. Currently, we end up reading the mask bits too
and therefore always report errors.
Ignore the register mask bits and check for only the status/clear bits.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The maximum output width of one pipeline depends on the LayerMixer's
capability. It may be different on each target. Also, MDP5 doesn't
have vertical limitation in one frame, as long as the pixel clock
can be supported.
This change obtains the maximum LM resolution from configuration
table and treat it as the whole pipe's limitation for MDP5. The size
limit on MDP4 is not changed.
Signed-off-by: Hai Li <hali@codeaurora.org>
For all of these devices, msm89xy was the lead chip, so standardize the
compatible names to align with convention used by rest of the qcom/msm
drivers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the MDP and HDMI support for msm8x94.
Note that HDMI PHY registers are not being accessed anymore from
the driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[rename compatible s/8x94/8994/ since preference is to not trust the
marketing folks who invent chip #'s but instead name things after the
lead chip.. we should rename some 80XY to 89XY to standardize on the
lead chip but leave that for another patch. Also, update dt bindings
doc]
Signed-off-by: Rob Clark <robdclark@gmail.com>
->reset() currently only accesses HDMI core registers, and yet it
is located in hdmi_phy*. Since no PHY registers are being
accessed during ->reset(), it would be better to bring that
function in hdmi core module where HDMI core registers are
usually being accessed.
This will also help for msm8x94 for which no PHY registers
accesses are done (->phy_init == NULL) but the HDMI PHY reset
from HDMI core still needs to be done.
Note:
SW_RESET_PLL bit is not written in hdmi_phy_8x60_reset(); this
write should not affect anything if the corresponding field is
not writable.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[fixed warning about unused 'phy' in hpd_enable() while merging]
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI controller on msm8x94 is version 1.3, which requires different
power supplies and works with 20nm DSI PHY. This change is to add
the basic support for this version.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some targets use pinctrl framework to configure some
pins. This change allows DSI driver to set default and
sleep pinctrl status.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current term of *dual panel* in DSI driver code causes confusion.
It is supposed to indicate the panel using two DSI links. Rename it
to *dual DSI*.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The source PLL to be used by each DSI PHY should be decided by
DSI manager based on dual DSI information, while the register
programming to select PLL is different from one type of PHY to
another. This change adds the H/W difference to PHY configuration
and updates the interface between DSI manager and PHY.
With this change, PLL selection can be supported on different
targets.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
single MST fixes from Maarten.
* tag 'topic/drm-fixes-2015-08-14' of git://anongit.freedesktop.org/drm-intel:
drm/dp/mst: Remove port after removing connector.
three display fixes for Intel.
* tag 'drm-intel-fixes-2015-08-14' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Commit planes on each crtc separately.
drm/i915: calculate primary visibility changes instead of calling from set_config
drm/i915: Only dither on 6bpc panels
Release all blocks after the pipe is disabled, even when vsync
didn't happen in some error cases. Allow requesting SMB multiple
times before configuring to hardware, by releasing blocks not
programmed to hardware yet for shrinking case.
This fixes a potential leak of shared memory pool blocks.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The atomic commit cannot easily undo and return an error once the
state is swapped. Change to uninterruptible wait, and ignore the
timeout error.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp4_get_frame_format() can dereference a drm_framebuffer when it's NULL.
Call it in mdp4_plane_mode_set only when we know fb is non-NULL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to return a new sgt, since the caller takes ownership of it.
Reported-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Put the Kconfig entries for bridge drivers into a separate menu so that
they are automatically grouped and don't clutter up the top-level menu.
While at it, move the bridge menu towards the end of the top-level menu
where the panel menu is already located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG4573 is used on the LG LCD LB043WV2-SD01, an industrial 4.3" TFT
panel with SPI control interface.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Okaya RS800480T-7X0GP to the DRM simple panel
driver.
The RS800480T-7X0GP is a WVGA (800x480) panel with an 18-bit parallel
LCD interface. It supports pixel clocks in the range of 30-40 MHz.
This panel details can be found at:
http://boundarydevices.com/product/7-800x480-display/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the NEC NL4827HC19-05B 480x272 panel to the DRM
simple panel driver.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[treding@nvidia.com: add .bpc field for panel]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B080UAN01 is an 8.0" WUXGA TFT LCD panel connected using four
DSI lanes. It can be supported by the simple-panel driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the data sheet, the minimum horizontal blanking interval
is 54 clocks (1 + 52 + 1), but tests with a Nitrogen6X have shown the
minimum working horizontal blanking interval to be 60 clocks.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The bus format both specifies the bpc and the way the individual bits get
serialized into the 7 LVDS timeslots.
While the is only one standard mapping for 6 bpc and so the driver could
infer the bit mapping from the bpc alone, there are more options for the
8 bpc case which makes specifiying the bus format mandatory.
To keep things consistent across panels and to set a precedent for new
panel additions add the proper bus format.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use vendor prefixes for Kconfig symbols and filenames. This should make
it easier to identify the various bridge drivers and to organize the
directory.
v2: fix object name for dw-hdmi (Fabio Estevam)
Signed-off-by: Thierry Reding <treding@nvidia.com>
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-intel-fixes because a bunch of atomic patch backporting
we had to do lead to horrible conflicts.
Conflicts:
drivers/gpu/drm/drm_crtc.c
Just a bit of context conflict between -next and -fixes.
drivers/gpu/drm/i915/intel_atomic.c
drivers/gpu/drm/i915/intel_display.c
Atomic conflicts, always pick the code from -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There is currently conflicting documentation on which steppings the
workaround is needed, up to C vs. forever. However there is post-C
stepping hardware that doesn't report port presence on DDI A, leading to
black screen on eDP. Assume the strap isn't connected, and try to enable
DDI A on these machines. (We'll still check the VBT for the info in DDI
init.)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP spec requires the checksum of the last block read to be written
when replying to TEST_EDID_READ. This patch fixes the current code
to do the same.
v2: removed loop for jumping blocks and performed direct addition
as recommended by Daniel
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent leaking the if scoping by containing the WA_REG
macro inside its own scope.
Reported-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter an allocation failure during ppggt creation (trivial
even with 16Gib+ RAM!), we need to remove the dead context from the
fpriv->context_idr along with the references.
gem_exec_ctx: page allocation failure: order:0, mode:0x8004
CPU: 3 PID: 27272 Comm: gem_exec_ctx Tainted: G W 4.2.0-rc5+ #37
0000000000000000 ffff880086ff7a78 ffffffff816b947a ffff88041ed90038
0000000000008004 ffff880086ff7b08 ffffffff8114b1a5 ffff880086ff7ac8
ffffffff8108d848 0000000000000000 ffffffff81ce84b8 0000000000000000
Call Trace:
[<ffffffff816b947a>] dump_stack+0x45/0x57
[<ffffffff8114b1a5>] warn_alloc_failed+0xd5/0x120
[<ffffffff8108d848>] ? __wake_up+0x48/0x60
[<ffffffff8114e0ed>] __alloc_pages_nodemask+0x73d/0x8e0
[<ffffffffc0472238>] ? i915_gem_execbuffer2+0x148/0x240 [i915]
[<ffffffffc0474240>] __setup_page_dma+0x30/0x110 [i915]
[<ffffffffc0477f61>] gen8_ppgtt_init+0x31/0x2f0 [i915]
[<ffffffffc04785e0>] i915_ppgtt_init+0x30/0x80 [i915]
[<ffffffffc0478928>] i915_ppgtt_create+0x48/0xc0 [i915]
[<ffffffffc046c9c2>] i915_gem_create_context+0x1c2/0x390 [i915]
[<ffffffffc046d9cb>] i915_gem_context_create_ioctl+0x5b/0xa0 [i915]
leading to an oops in i915_gem_context_close. Also note that this
benchmark should not be running out of memory in the first place...
Testcase: igt/benchmark/gem_exec_ctx -b create # ppgtt >= 2
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IOMMU for Intel graphics has historically had many issues resulting
in random GPU hangs. Lets include its status when capturing the GPU hang
error state for post-mortem analysis.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If idle to active bit is set, the rest of the fields
in CSQ are not valid.
Bail out early if this is the case in order to prevent
rest of the loop inspecting stale values.
This was found by Bspec/code inspection. Doesn't seem to fix any of
the known issues.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
[danvet: Add note about how this was found.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I started digging this when I noticed that the BDW code was just
reserving 1mb by coincidence since it was reading reserved fields.
Then I noticed we didn't have any values set for SNB and earlier, and
that the HSW sizes were wrong. After that, I noticed that the reserved
area has a specific start, and may not exactly end where the stolen
memory ends. I also noticed the base pointer can be zero. So I decided
to just write a single patch fixing everything instead of 20 patches
that would be much harder to review.
This patch may solve random stolen memory corruption/problems on
almost all platforms. Notice that since this is always dealing with
the top of the stolen memory, the problems are not so easy to
reproduce - especially since FBC is still disabled by default.
One of the major differences of this patch is that we now look at both
the size and base address. By only looking at the size we were
assuming that the reserved area was always at the very top of
stolen, which is not always true.
After we merge the patch series that allows user space to allocate
stolen memory we'll be able to write IGT tests that maybe catch the
bugs fixed by this patch.
v2:
- s/BIOS reserved/stolen reserved/g (Chris)
- Don't DRM_ERROR if we can't do anything about it (Chris)
- Improve debug messages (Chris).
- Use the gen7 version instead of gen6 on HSW. Tom found some
documentation problems, so I think with gen7 we're on the safer
side (Tom).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register needs to be updated with masked writes.
This was found by code inspection and comparison with Bspec and
doesn't seem to fix any known issue.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Add note about impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter frequent problems with dp aux channel
communications, we end up spamming the dmesg with the
exact similar trace and status.
Inject a new backtrace only if we have new information
to share as otherwise we flush out all other important
stuff.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-EDEADLK has special meaning in atomic, but get_fence may call
i915_find_fence_reg which can return -EDEADLK.
This has special meaning in the atomic world, so convert the error
to -EBUSY for this case.
Changes since v1:
- Add comment in the code.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The rest will be a noop anyway, since without modeset there will be
no updated dplls and no modeset state to update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything's atomic, checking encoder->base.crtc is enough.
This function doesn't have the locks to dereference crtc->state, but
stealing an encoder bound to any crtc is probably enough reason to warn.
Changes since v1:
- Commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
connectors_active will be removed, so just calculate this instead.
Changes since v1:
- Look for the right pointer in intel_sanitize_encoder.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of allocating pipe_config on the stack use the old
crtc_state, it's only going to freed from this point on.
All crtc' are now only checked once during modeset,
because false positives can happen with encoders after
dpms changes and to limit the amount of errors for 1 failure.
Changes since v1:
- crtc_state -> old_crtc_state
- state -> old_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Connectors are updated atomically now, so the only interaction
with the encoder is through base.crtc.
If it's NULL the encoder's not part of any crtc, and if it's
not NULL then active should be equal to crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is handled by the atomic core now, no need to check this for ourself.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now dpms callbacks can still fiddle with the connector state,
but it can only turn connectors off.
This is remediated by only checking crtc->state->active when the
connector is active, and ignore crtc->state->active when the
connector is off.
connectors_active is no longer checked, and will be removed later
in this series together with dpms.
Another check for !encoder->crtc is performed by check_encoder_state
too, so it can be removed.
Changes since v1:
- Add commit message.
- rename state to old_state.
- Move deletion of mst_port check to mst patch.
Changes since v2:
- Fix a null pointer dereference on MST now hw readout is fixed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fully remove the MST connector from the atomic state, and remove the
early returns in check_*_state for MST connectors.
With atomic the state can be made consistent all the time.
Thanks to Sivakumar Thulasimani for the idea of using
drm_atomic_helper_set_config.
Changes since v1:
- Remove the MST check in intel_connector_check_state too.
Changes since v2:
- Use drm_atomic_helper_set_config.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set connectors_changed to force a modeset if the panel fitter's force
enabled on eDP.
Changes since v1:
- Use connectors_changed instead of active_changed because it's a
routing update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two small bug fixes for the code you pulled for 4.3:
- Used a SHIFT define instead of a MASK define to check if a bit is turned on
when destroying hqd. Luckily, this is in gfx7 interface file with amdgpu,
which was used only for bring-up purposes of amdgpu, so no real effect on
a running system
- Used a logical AND instead of a bitwise AND operator, when initializing
sdma virtual memory when using SDMA queues
* tag 'drm-amdkfd-next-fixes-2015-08-05' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: fix bug when initializing sdma vm
drm/amdgpu: fix bug when amdkfd destroys hqd
This serie of patches fix minor bugs around how driver sub-components are
bind and planes z-ordering.
The main part is about atomic support: using more atomic helpers allow us
to simplify the code (~300 lines removed) and to ahve a better match between
drm concepts (planes and crtc) and hardware split.
[airlied: fixed up conflict in atomic code]
* 'drm-sti-next-atomic-2015-08-11' of http://git.linaro.org/people/benjamin.gaignard/kernel:
drm/sti: atomic crtc/plane update
drm/sti: rename files and functions
drm/sti: code clean up
drm/sti: fix dynamic z-ordering
drm: sti: fix sub-components bind
This reverts commit 1addc12648
This commit seems to cause crashes in gk104_fifo_intr_runlist() by
returning 0xbad0da00 when register 0x2a00 is read. Since this commit was
intended for GM20B which is not completely supported yet, let's revert
it for the time being.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This addresses two issues that cause problems with viewperf maya-03 in
situation with memory pressure.
The first issue causes attempts to unreserve buffers if batched
reservation fails due to, for example, a signal pending. While previously
the ttm_eu api was resistant against this type of error, it is no longer
and the lockdep code will complain about attempting to unreserve buffers
that are not reserved. The issue is resolved by avoid calling
ttm_eu_backoff_reservation in the buffer reserve error path.
The second issue is that the binding_mutex may be held when user-space
fence objects are created and hence during memory reclaims. This may cause
recursive attempts to grab the binding mutex. The issue is resolved by not
holding the binding mutex across fence creation and submission.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The likelihood of getting a large number of panel drivers from different
vendors is quite high. Add a prefix to the two existing Samsung panel
drivers to set a guideline for future patch submissions. Using vendor
prefixes consistently should allow a cleaner organization of the tree.
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that the PTN3460 driver has been rewritten as a proper I2C driver
and there is infrastructure to hook up the bridge with a DRM device, it
is no longer necessary to have this dependency to ensure the correct
build mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR1 introduced on Tegra210 supports HDMI 2.0 and DisplayPort. Add
HDMI support and name the debugfs node after the type of SOR. The SOR
introduced with Tegra124 is known simply as "sor", whereas the
additional SOR found on Tegra210 is known as "sor1".
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra210 is very similar to the version found on
Tegra124, except that it no longer supports LVDS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move all code into the new canonical ->disable() and ->enable() helper
callbacks so that they play extra nice with atomic DPMS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
While at it, remove the enabled field that hasn't been used since the
demidlayering of the output drivers done in preparation for the atomic
mode-setting conversion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of duplicating most of the code to set up a debugfs file, use
the existing DRM core debugfs infrastructure instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The head state registers are per head, so they must be properly indexed.
This has worked fine so far because all boards with eDP use it as the
primary output, so it is very likely to end up attached to head 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The data structure is always only read, never written, and can hence be
referred to by a const pointer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tearing down debugfs support, make sure to reset the fields to NULL
in the correct order, otherwise the debugfs root will not be properly
removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM minor is needed to teardown debugfs, so it needs to be tracked
to prevent a crash on driver removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the SOR device fails, output proper error messages to help
diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TRM lists indexed registers without an underscore to separate name
from index. Use that convention in the driver for consistency.
While at it, rename some of the field names to the names used in the
TRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DPAUX isn't attached to an SOR the interrupts are not useful.
This also prevents a race that could potentially cause a crash on driver
removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX code paths already configure the pads in AUX mode, but there
is no way to reconfigure them in I2C mode for HDMI (the DPAUX module is
unused in that case). Enabling the pads in I2C mode by default is the
quickest way to support HDMI. Eventually this may need an explicit call
in the user drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the dpaux device fails, output proper error messages to
help diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra132 to Tegra210, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra124 to Tegra132, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra114 to Tegra124, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In video modes without sync pulses, the horizontal back-porch needs to
include the horizontal sync width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The call to platform_driver_register() will already set up the .owner
field, so there's no need to do it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The horizontal pulse enable bits are named H_PULSE{0,1,2}_ENABLE in the
TRM. Modify the driver to use the same naming for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Record interrupt statistics, such as the number of frames and VBLANKs
received and the number of FIFO underflow and overflows.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Request a syncpoint for display prior to registering the host1x client.
This will ensure that the syncpoint will be acquired when the KMS driver
initializes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Upon driver load, reset the VBLANK machinery to off to reflect the
hardware state. Since the ->reset() callback is called from the initial
drm_mode_config_reset() call, move the latter after the VBLANK machinery
initialization by drm_vblank_init().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Keep track of the number of users of DSI and CSI pads and power down the
regulators that supply the bricks when all users are gone.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some changes are needed to the configuration settings for some lanes. In
addition, the clock lanes for the CSI pads can no longer be calibrated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
While Tegra132 has the same pads as Tegra124, some configuration values
need to be programmed slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before starting a new calibration cycle, make sure to clear the current
status by writing a 1 to the various "calibration done" bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use more consistent names for the clock lane configuration registers and
fix the offset of the upper clock lane configuration register for the
first DSI pad.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Parameterize more of the register programming to accomodate for changes
required by future SoC generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch is based on the upstream commit 5ac1c4bcf0 and amended
for v4.2 to make sure it works as intended.
Repeated calls to begin_crtc_commit can cause warnings like this:
[ 169.127746] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
[ 169.127835] in_atomic(): 0, irqs_disabled(): 1, pid: 1947, name: kms_flip
[ 169.127840] 3 locks held by kms_flip/1947:
[ 169.127843] #0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff814774bc>] __drm_modeset_lock_all+0x9c/0x130
[ 169.127860] #1: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffff814774cd>] __drm_modeset_lock_all+0xad/0x130
[ 169.127870] #2: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffff81477178>] drm_modeset_lock+0x38/0x110
[ 169.127879] irq event stamp: 665690
[ 169.127882] hardirqs last enabled at (665689): [<ffffffff817ffdb5>] _raw_spin_unlock_irqrestore+0x55/0x70
[ 169.127889] hardirqs last disabled at (665690): [<ffffffffc0197a23>] intel_pipe_update_start+0x113/0x5c0 [i915]
[ 169.127936] softirqs last enabled at (665470): [<ffffffff8108a766>] __do_softirq+0x236/0x650
[ 169.127942] softirqs last disabled at (665465): [<ffffffff8108ae75>] irq_exit+0xc5/0xd0
[ 169.127951] CPU: 1 PID: 1947 Comm: kms_flip Not tainted 4.1.0-rc4-patser+ #4039
[ 169.127954] Hardware name: LENOVO 2349AV8/2349AV8, BIOS G1ETA5WW (2.65 ) 04/15/2014
[ 169.127957] ffff8800c49036f0 ffff8800cde5fa28 ffffffff817f6907 0000000080000001
[ 169.127964] 0000000000000000 ffff8800cde5fa58 ffffffff810aebed 0000000000000046
[ 169.127970] ffffffff81c5d518 0000000000000268 0000000000000000 ffff8800cde5fa88
[ 169.127981] Call Trace:
[ 169.127992] [<ffffffff817f6907>] dump_stack+0x4f/0x7b
[ 169.128001] [<ffffffff810aebed>] ___might_sleep+0x16d/0x270
[ 169.128008] [<ffffffff810aed38>] __might_sleep+0x48/0x90
[ 169.128017] [<ffffffff817fc359>] mutex_lock_nested+0x29/0x410
[ 169.128073] [<ffffffffc01635f0>] ? vgpu_write64+0x220/0x220 [i915]
[ 169.128138] [<ffffffffc017fddf>] ? ironlake_update_primary_plane+0x2ff/0x410 [i915]
[ 169.128198] [<ffffffffc0190e75>] intel_frontbuffer_flush+0x25/0x70 [i915]
[ 169.128253] [<ffffffffc01831ac>] intel_finish_crtc_commit+0x4c/0x180 [i915]
[ 169.128279] [<ffffffffc00784ac>] drm_atomic_helper_commit_planes+0x12c/0x240 [drm_kms_helper]
[ 169.128338] [<ffffffffc0184264>] __intel_set_mode+0x684/0x830 [i915]
[ 169.128378] [<ffffffffc018a84a>] intel_crtc_set_config+0x49a/0x620 [i915]
[ 169.128385] [<ffffffff817fdd39>] ? mutex_unlock+0x9/0x10
[ 169.128391] [<ffffffff81467b69>] drm_mode_set_config_internal+0x69/0x120
[ 169.128398] [<ffffffff8119b547>] ? might_fault+0x57/0xb0
[ 169.128403] [<ffffffff8146bf93>] drm_mode_setcrtc+0x253/0x620
[ 169.128409] [<ffffffff8145c600>] drm_ioctl+0x1a0/0x6a0
[ 169.128415] [<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[ 169.128424] [<ffffffff811e9ab8>] do_vfs_ioctl+0x2f8/0x530
[ 169.128429] [<ffffffff810d0fcd>] ? trace_hardirqs_on+0xd/0x10
[ 169.128435] [<ffffffff812e7676>] ? selinux_file_ioctl+0x56/0x100
[ 169.128439] [<ffffffff811e9d71>] SyS_ioctl+0x81/0xa0
[ 169.128445] [<ffffffff81800697>] system_call_fastpath+0x12/0x6f
Solve it by using the newly introduced drm_atomic_helper_commit_planes_on_crtc.
The problem here was that the drm_atomic_helper_commit_planes() helper
we were using was basically designed to do
begin_crtc_commit(crtc #1)
begin_crtc_commit(crtc #2)
...
commit all planes
finish_crtc_commit(crtc #1)
finish_crtc_commit(crtc #2)
The problem here is that since our hardware relies on vblank evasion,
our CRTC 'begin' function waits until we're out of the danger zone in
which register writes might wind up straddling the vblank, then disables
interrupts; our 'finish' function re-enables interrupts after the
registers have been written. The expectation is that the operations between
'begin' and 'end' must be performed without sleeping (since interrupts
are disabled) and should happen as quickly as possible. By clumping all
of the 'begin' calls together, we introducing a couple problems:
* Subsequent 'begin' invocations might sleep (which is illegal)
* The first 'begin' ensured that we were far enough from the vblank that
we could write our registers safely and ensure they all fell within
the same frame. Adding extra delay waiting for subsequent CRTC's
wasn't accounted for and could put us back into the 'danger zone' for
CRTC #1.
This commit solves the problem by using a new helper that allows an
order of operations like:
for each crtc {
begin_crtc_commit(crtc) // sleep (maybe), then disable interrupts
commit planes for this specific CRTC
end_crtc_commit(crtc) // reenable interrupts
}
so that sleeps will only be performed while interrupts are enabled and
we can be sure that registers for a CRTC will be written immediately
once we know we're in the safe zone.
The crtc->config->base.crtc update may seem unrelated, but the helper
will use it to obtain the crtc for the state. Without the update it
will dereference NULL and crash.
Changes since v1:
- Use Matt Roper's commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should be much cleaner, with the same effects.
(cherry picked for v4.2 from commit fb9d6cf8c2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
