The dw_hdmi enable/disable handling is particularly weak in several
regards:
* The hotplug interrupt could call hdmi_poweron() or hdmi_poweroff()
while DRM is setting a mode, which could race with a mode being set.
* Hotplug will always re-enable the phy whenever it detects an active
hotplug signal, even if DRM has disabled the output.
Resolve all of these by introducing a mutex to prevent races, and a
state-tracking bool so we know whether DRM wishes the output to be
enabled. We choose to use our own mutex rather than ->struct_mutex
so that we can still process interrupts in a timely fashion.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi_phy_enable_power() is not about enabling and disabling power.
It is about allowing or preventing power-down mode being entered - the
register is documented as "Power-down enable (active low 0b)."
This can be seen as the bit has no effect when the HDMI phy is
operational on iMX6 hardware.
Rename the function to dw_hdmi_phy_enable_powerdown() to reflect the
documentation, make it take a bool for the 'enable' argument, and invert
the value to be written.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On a mode set, DRM makes the following sequence of calls:
* for_each_encoder
* bridge mode_fixup
* encoder mode_fixup
* crtc mode_fixup
* for_each_encoder
* bridge disable
* encoder prepare
* bridge post_disable
* disable unused encoders
* crtc prepare
* crtc mode_set
* for_each_encoder
* encoder mode_set
* bridge mode_set
* crtc commit
* for_each_encoder
* bridge pre_enable
* encoder commit
* bridge enable
dw_hdmi enables the HDMI output in both the bridge mode_set() and also
the bridge enable() step. This is duplicated work - we can avoid the
setup in mode_set() and just do it in the enable() stage. This
simplifies the code a little.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only enable audio support if the sink supports audio in some form, as
defined via its EDID. We discover this capability using the generic
drm_detect_monitor_audio() function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The FSL kernel detects the HDMI vendor id, and uses this to set
hdmi->edid_cfg.hdmi_cap, which is then used to set mdvi appropriately,
rather than detecting whether we are outputting a CEA mode. Update
the dw_hdmi code to use this logic, but lets eliminate the mdvi
variable, prefering the more verbose "hdmi->sink_is_hdmi" instead.
Use the generic drm_detect_hdmi_monitor() to detect a HDMI sink.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As mentioned in the previous commit, the dw-hdmi driver does not support
pixel doubled modes at present; it does not configure the PLL correctly
for these modes. Therefore, filter out the double-clocked modes as we
presently are unable to support them.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dw_hdmi sets a pixel repetition factor of 1 for VICs 10-15, 25-30 and
35-38. However, DRM uses their native resolutions in its timing
information. For example, VIC 14 can be 1440x480 with no repetition,
or 720x480 with one pixel repetition. As DRM uses 1440 pixels per line
for this video mode, we need no pixel repetition.
In any case, pixel repetition appears broken in dw_hdmi.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iMX6 devices suffer from an errata (ERR005174) where the audio FIFO can
be emptied while it is partially full, resulting in misalignment of the
audio samples.
To prevent this, the errata workaround recommends writing N as zero
until the audio FIFO has been loaded by DMA. Writing N=0 prevents the
HDMI bridge from reading from the audio FIFO, effectively disabling
audio.
This means we need to provide the audio driver with a pair of functions
to enable/disable audio. These are dw_hdmi_audio_enable() and
dw_hdmi_audio_disable().
A spinlock is introduced to ensure that setting the CTS/N values can't
race, ensuring that the audio driver calling the enable/disable
functions (which are called in an atomic context) can't race with a
modeset.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce dw_hdmi_set_sample_rate(), which allows us to configure the
audio sample rate, setting the CTS/N values appropriately.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the struct hdmi_vmode mhsyncpolarity/mvsyncpolarity/minterlaced
members, which are only used within a single function. We can directly
reference the appropriate mode->flags instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a YCBCR format is selected, we can merely copy the colorimetry
information directly as we use the same definitions for both the
unpacked AVI info frame and the hdmi_data_info structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clean up hdmi_set_clk_regenerator() by allowing it to take the audio
sample rate and ratio directly, rather than hiding it inside the
function. Raise the unsupported pixel clock/sample rate message from
debug to error level as this results in audio not working correctly.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy configuration is dependent on the SoC, and we look up values for
some of the registers in SoC specific data. However, we had partially
programmed the phy before we had successfully looked up the clock rate.
Also, we were only checking that we had a valid configuration for the
currctrl register.
Move all these lookups to the start of this function instead, so we can
check that all lookups were successful before beginning to program the
phy.
Tested-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The phy comments in dw_hdmi.c applied to the iMX6 version. Move these
comments to the iMX6 dw_hdmi-imx data along side the data.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Describe capabilities of the HLCDC IP found on sama5d4 SoCs and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Describe capabilities of the HLCDC IP found on at91sam9n12 SoC and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Describe capabilities of the HLCDC IP found on at91sam9x5 SoCs and add a
new entry to the atmel_hlcdc_of_match table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The atmel-hlcdc driver already supports atomic operations, add the
missing DRM_ATOMIC flag to expose the atomic features to userspace.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If PM is enabled but PM_SLEEP is disabled, the suspend/resume functions
are still unused and produce a compiler warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 4.1+
Pagetables can be moved and therefore the page directory update can be necessary
for the current cs even if none of the the bo's are moved. In that scenario
there is no fence between the sdma0 and gfx ring, so we add one.
v2 (chk): rebased
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Explicitly select BACKLIGHT_LCD_SUPPORT to satisfy the direct dependency
of BACKLIGHT_CLASS_DEVICE.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Explicitly select BACKLIGHT_LCD_SUPPORT to satisfy the direct dependency
of BACKLIGHT_CLASS_DEVICE.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rework run queue implementation, especially remove the odd list handling.
v2: cleanup the code only, no algorithem change.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
fix the bug that there is duplicated bo_update_mapping issued
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
bo_list_clone() will take a lot of time when bo_list hold too much
elements, like above 7000
Signed-off-by: Monk.Liu <monk.liu@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
It's not validated yet and causes more harm than good.
Avoids spurious resets.
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
remaining timeout returned by amdgpu_fence_wait_any can be larger than
max int value, thus the truncated 32 bit value in r ends up being
negative while its original long value is positive.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
fix fence is released when pass to **fence sometimes.
add reference for it.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-and-Reviewed-by: Leo Liu <leo.liu@amd.com>
Not used any more.
v2: remove amd_sched_emit as well.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Similar to radeon, except that amdgpu doesn't even use struct_mutex to
protect anything like the shared z buffer (sane gpu architecture,
yay!). And the code already grabs the globa adev->ring_lock, so this
code can't race with itself. Which makes struct_mutex completely
redundnant. Remove it.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It really doesn't protect anything which doesn't have other locks
already. Also this is run from driver unload code so not much need for
locks anyway.
Same changes as for radeon really.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We already grab 2 device-global locks (write-sema rdev->pm.mclk_lock
and rdev->ring_lock), adding another global mutex won't serialize this
code more. And since there's really nothing interesting that gets
protected in radeon by dev->struct mutex (we only have the global z
buffer owners and it's still serializing gem bo destruction in the drm
core - which is irrelevant since radeon uses ttm anyway internally)
this doesn't add protection. Remove it.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It really doesn't protect anything which doesn't have other locks
already. Also this is run from driver unload code so not much need for
locks anyway.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The workaround simply doesn't work because VM mappings
are controlled by userspace not the kernel.
Additional to that this is just a performance problem
which happens if you have holes in your VM mapping.
v2: adjust virtual addr alignment as well.
v3: fix trivial warning
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Monk Liu <monk.liu@amd.com> (v1)
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com> (v2)
Looks like that somehow got missed while during porting the radeon changes.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It was just a wrapper for fence_wait anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The common kernel function does the same thing.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
scheduler fence is based on kernel fence framework.
v2: squash in Christian's build fix
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
v2: rebased
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Avoiding a couple of casts.
v2: rename c_entity to entity as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Cleanup the kernel context handling.
v2: rebased
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com> (v1)
Id's are for the IOCTL ABI only.
v2: remove tgid as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
We didn't initialized the mutex in the cloned bo list resulting in nice
warnings from lockdep. Also fixes error handling in this function.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This way can avoid interrupt lost, and can process sched job exactly.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
This function is used to get the next queued sequence number
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This function is to update last_emitted_v_seq and wake up the waiters.
It should be called by driver in the run_job backend function
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
It is clean to update last_queued_v_seq in the scheduler module
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Fix the code alignment, etc.
v2: rebase the code
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
every sbumission should be able to get a fence.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <jammy.zhou@amd.com>
It is theoretically possible that a swapped out BO gets the
same GTT address, but different backing pages while being swapped in.
Instead just use another VA state to note updated areas.
Ported from not upstream yet radeon commit with the same name.
v2: fix some bugs in the original implementation found in the radeon code.
v3: squash in VCE/UVD fix
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
thus unnecessary wake up could be avoid between rings
v2:
move wait_queue_head to fence_drv from ring
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
origninal method will sleep/schedule at the granurarity of HZ/2 and
based on seq signal method, the new implement is based on kernel fance
interface, no unnecessary schedule at all
v2: replace logic of original amdgpu_fence_wait_any
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
if enabling scheduler, then the queued seq is assigned
when pushing job before emitting job.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
the job must be emitted by scheduler, otherwise scheduler is abnormal.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
This option can be used to specify the max number of submissions in the
active HW queue. The default value is 2 now.
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This option can be used to specify the max job number in the job queue,
and it is 16 by default.
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
it is possible that the callback isn't defined sometimes.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
fence_process may be called from kthread, user thread and interrupt context.
it is possible to called concurrently, then will wake up fence queue multiple times.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
use kernel context to submit command for vm
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
user mode will still use pte ring as a normal ring.
if the prepare job generates another command(update pte) on its ring in scheduler,
then will kill scheduler which is going to waiting later job but pending running job.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
BO validation is moved to scheduler except usrptr which must be validated
in user process
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
run queue:
A set of entities scheduling commands for the same ring. It
implements the scheduling policy that selects the next entity to
emit commands from.
entity:
A scheduler entity is a wrapper around a job queue or a group of
other entities. This can be used to build hierarchies of entities.
For example all job queue entities belonging to the same process
may be placed in a higher level entity and scheduled against other
process entities.
Entities take turns emitting jobs from their job queue to the
corresponding hardware ring, in accordance with the scheduler policy.
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Acked-by: Christian K?nig <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
v2: agd5f: fix the rb setup.
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
v2: agd5f: fix up XDMA golden settings
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
v2: agd5f: prepare for release
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
v2: agd5f: prepare for release
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Zhang <david1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
use kmalloc_array instead of kcalloc where appropriate and other
cleanups.
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Make the definitions common for all driver components
v2: fix kfd
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Add GPU family definitions and timeout value for IP components.
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Feel free to suggest more.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Acked-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
the definitions can be shared by different IP components.
v2: fix include path
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
We need to return the sequence number to userspace
even when we don't use user fences.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This makes assigning VM IDs independent from the use of VM IDs.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
v2 (chk): split fix from original patch
Signed-off-by: monk.liu <monk.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Otherwise the first 16 fences of a context will always signal immediately.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
It's not used any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This is a prerequisite for the GPU scheduler to make the order
of submission independent from the order of execution.
v2: properly implement the locking
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This also requires some error handling from the callers of that function.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
The comment is misleading and incorrect, remove it.
Printing the id is completely meaningless and this practice
can cause a race conditions on command submission.
The flags and hangs fields are completely unused.
Give all fields a common indentation.
v2: remove fpriv reference and unused flags as well, fix debug message.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
This new interface can be used by IP components to retrieve the
firmware information from the core driver.
v2: fix one typo
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhou@amd.com>
Signed-off-by: Young Yang <Young.Yang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This implements the interface for atombios command
and data table access.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CGS (Common Graphics Services) is an AMD cross component
abstraction layer to designed to better encapsulate
specific IP block drivers so different teams can effectively
work on differnet IP block drivers independently. It provides
a common interface for things like accessing registers,
allocating GPU memory, and registering interrupt sources.
The plan is to eventually move more and more IP drivers to
this interface. The first user is the ACP IP driver.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In function 'amdgpu_uvd_cs_pass2':
warning: 'min_ctx_size' may be used uninitialized in this function
buf_sizes[0x4] = min_ctx_size;
^
note: 'min_ctx_size' was declared here
unsigned image_size, tmp, min_dpb_size, num_dpb_buffer, min_ctx_size;
^
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Everytime we use the logical context with execlists it becomes dirty (as
the hardware will write the new register values afterwards, as well as
the GPU state that will be used). We need to then flag the context as
dirty everytime since after a swap-out/swap-in cycle the dirty flag will
be cleared, and a further swap-out cycle will then loose the most recent
GPU state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
A couple of fixes from the previous pull request as well as gl3 support.
There is one drm core change, an export of a previously private function.
Take 2 implementing screen targets, this time with the fbdev code adjusted
accordingly.
Also there is an implementation of register-driven command buffers, that
overrides the FIFO ring for command processing. It's needed for our upcoming
hardware revision.
* 'vmwgfx-next' of git://people.freedesktop.org/~thomash/linux: (35 commits)
drm/vmwgfx: Fix copyright headers
drm/vmwgfx: Add DX query support. Various fixes.
drm/vmwgfx: Add command parser support for a couple of DX commands
drm/vmwgfx: Command parser fixes for DX
drm/vmwgfx: Initial DX support
drm/vmwgfx: Update device includes for DX device functionality
drm: export the DRM permission check code
drm/vmwgfx: Fix crash when unloading vmwgfx v2
drm/vmwgfx: Fix framebuffer creation on older hardware
drm/vmwgfx: Fixed topology boundary checking for Screen Targets
drm/vmwgfx: Fix an uninitialized value
drm/vmwgfx: Fix compiler warning with 32-bit dma_addr_t
drm/vmwgfx: Kill a bunch of sparse warnings
drm/vmwgfx: Fix kms preferred mode sorting
drm/vmwgfx: Reinstate the legacy display system dirty callback
drm/vmwgfx: Implement fbdev on kms v2
drm/vmwgfx: Add a kernel interface to create a framebuffer v2
drm/vmwgfx: Avoid cmdbuf alloc sleeping if !TASK_RUNNING
drm/vmwgfx: Convert screen targets to new helpers v3
drm/vmwgfx: Convert screen objects to the new helpers
...
This introduces support for a couple of new panels and also contains
some work to restructure the directories to get more consistency, to
deal better with more panel and bridge drivers getting added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Dee7
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.3-rc1
This introduces support for a couple of new panels and also contains
some work to restructure the directories to get more consistency, to
deal better with more panel and bridge drivers getting added.
* tag 'drm/panel/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/bridge: Put Kconfig entries in a separate menu
drm/panel: Add support for LG LG4573 480x800 4.3" panel
drm/panel: Add display timing for Okaya RS800480T-7X0GP
of: Add Okaya Electric America vendor prefix
drm/panel: simple: Add support for NEC NL4827HC19-05B 480x272 panel
drm/panel: simple: Add support for AUO B080UAN01
drm/panel: simple: Correct minimum hsync length of the HannStar HSD070PWW1 panel
drm/panel: simple: Add bus format for HannStar HSD070PWW1 LVDS panel
drm/bridge: Add vendor prefixes
drm/panel: Add Samsung prefix to panel drivers
drm/exynos: Remove PTN3460 dependency
There are a bunch of non-critical fixes here that I've collected over
the past few months, but the biggest part is Tegra210 support, in the
DC, DSI and SOR/HDMI drivers.
Also this finally restores DPMS with atomic mode-setting, something
that has been broken since the conversion and which I had originally
expected to take far less longer to fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxYn
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.3-rc1
There are a bunch of non-critical fixes here that I've collected over
the past few months, but the biggest part is Tegra210 support, in the
DC, DSI and SOR/HDMI drivers.
Also this finally restores DPMS with atomic mode-setting, something
that has been broken since the conversion and which I had originally
expected to take far less longer to fix.
* tag 'drm/tegra/for-4.3-rc1' of git://anongit.freedesktop.org/tegra/linux: (41 commits)
drm/tegra: sor: Add HDMI support
drm/tegra: sor: Add Tegra210 eDP support
drm/tegra: dc: Implement atomic DPMS
drm/tegra: sor: Restore DPMS
drm/tegra: dsi: Restore DPMS
drm/tegra: hdmi: Restore DPMS
drm/tegra: rgb: Restore DPMS
drm/tegra: sor: Use DRM debugfs infrastructure for CRC
drm/tegra: sor: Write correct head state registers
drm/tegra: sor: Constify display mode
drm/tegra: sor: Reset the correct debugfs fields
drm/tegra: sor: Set minor after debugfs initialization
drm/tegra: sor: Provide error messages in probe
drm/tegra: sor: Rename registers for consistency
drm/tegra: dpaux: Disable interrupt when detached
drm/tegra: dpaux: Configure pads as I2C by default
drm/tegra: dpaux: Provide error message in probe
drm/tegra: dsi: Add Tegra210 support
drm/tegra: dsi: Add Tegra132 support
drm/tegra: dsi: Add Tegra124 support
...
Summary:
- Clean up HDMI and MIXER parts
- Clean up legacy structures specific to Exynos DRM
. This patch series removes existing exyons_drm_display and
exynos_drm_encoder structures specific to Exynos DRM, and
makes them to replace with common drm_encoder structure.
With cleanup patch, we removes exynos_drm_encoder module.
- Clean up gem, dmabuf and buffer modules
. This patch series replaces existing Exynos DRM dmabuf codes
with common drm prime ones, and embeds all codes of exynos_drm_buf
into exynos_drm_gem module.
With cleanup patch, we removes exynos_drm_buf and exynos_drm_dmabuf
modules.
- And some fixups.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: (53 commits)
drm/exynos: merge exynos_drm_buf.c to exynos_drm_gem.c
drm/exynos: use prime helpers
drm/exynos: remove function roundup_gem_size
drm/exynos: remove function update_vm_cache_attr
drm/exynos: remove function check_gem_flags
drm/exynos: use ERR_PTR instead of NULL in exynos_drm_gem_init
drm/exynos: remove unused fields of struct exynos_drm_gem_buf
drm/exynos: stop copying sg table
drm/exynos: remove function exynos_drm_gem_map_buf
drm/exynos: remove mutex locking in pagefault handler
drm/exynos: remove function convert_to_vm_err_msg
drm/exynos: stop using sgtable in page fault handler
drm/exynos: remove struct exynos_drm_encoder layer
drm/exynos: fold encoder setup into exynos_drm_load()
drm/exynos: remove exynos_drm_create_enc_conn()
drm/exynos: remove exynos_encoder's .commit() op
drm/exynos: remove extra call to exynos_dp_commit()
drm/exynos: remove extra call to hdmi_commit()
drm/exynos: remove struct exynos_drm_display
drm/exynos: simplify calculation of possible CRTCs
...
1) includes all the drm/msm side of things for upstream kernel working
on dragonboard 410c (still some pending work on adv7533 bridge chip)
2) initial support for msm8x94 (snapdragon 810)
3) support for msm8x74v1 (in addition to existing v2 support)
4) support for dma planes on mdp5 (additional planes that cannot scale/csc)
5) more yuv format support for mdp5 (single plane vyuy/uyvy/yuyv/yvyu,
two plane nv16/nv61, and three plane yuv420/yvu420)
6) rotation support for mdp5
7) initial hdcp support
8) fixes, etc
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (46 commits)
drm/msm/dsi: Introduce DSI configuration module
drm/msm/dsi: Make each PHY type compilation independent
drm/msm/dsi: Split PHY drivers to separate files
drm/msm/dsi: Return void from msm_dsi_phy_disable()
drm/msm/dsi: Specify bitmask to set source PLL
drm/msm/mdp: Clear pending interrupt status before enable interrupt
drm/msm/mdp5: Add rotation (hflip/vflip) support to MDP5 planes (v2)
drm/msm: add calls to prepare and unprepare panel
drm/msm/dsi: Modify dsi manager bridge ops to work with external bridges
drm/msm/dsi: Allow dsi to connect to an external bridge
drm/msm/dsi: Create a helper to check if there is a connected device
drm/msm/dsi: Refer to connected device as 'device' instead of 'panel'
drm/msm/dsi: Make TE gpio optional
drm/msm: mdp4 lvds: get panel node via of graph parsing
drm/msm: dsi host: Use device graph parsing to parse connected panel
drm/msm: dsi host: add missing of_node_put()
drm/msm: Enable clocks during enable/disable_vblank() callbacks
drm/msm/mdp5: Add support for msm8x74v1
drm/msm/mdp5: Add DMA pipe planes for MDP5
drm/msm/mdp: Add capabilities to MDP planes (v2)
...
Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
Convert g2d_userptr_get_dma_addr() to pin pages using get_vaddr_frames().
This removes the knowledge about vmas and mmap_sem locking from exynos
driver. Also it fixes a problem that the function has been mapping user
provided address without holding mmap_sem.
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct exynos_drm_gem_obj can have fields of the struct
exynos_drm_gem_buf then don't need to use exynos_drm_buf.c file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The dma-buf codes of exynos drm is almost same with prime helpers. A
difference is that consider DMA_NONE when import dma-buf, but it's wrong
and we don't consider it any more, so we can use prime interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function roundup_gem_size can be merged in exynos_drm_gem_create.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function update_vm_cache_attr can be merged in exynos_drm_gem_mmap.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function check_gem_flags is too simple, so it's better to move codes
in each consumer functions.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The userptr, write and pfnmap of struct exynos_drm_gem_buf are not used
anywhere.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already struct exynos_drm_gem_buf has pages of the buffer, so we don't
need to copy from sg table of the buffer to sg table of dma-buf
attachment, just can make sg table from pages of the buffer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The exynos_drm_gem_map_buf can be merged in exynos_drm_gem_fault.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no reason to use mutex locking in pagefault handler.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The convert_to_vm_err_msg is called just once by exynos_drm_gem_fault,
so it's simple not to use the function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already struct exynos_drm_gem_buf has pages of the buffer when buffer is
created, so just can use pages in page fault handler, we don't have to
make sgtable of the buffer. But this needs to construct pages of the
buffer that is imported from dma-buf prime.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
struct exynos_drm_encoder was justing wrapping struct drm_encoder, it had
only a drm_encoder member and the internal exynos_drm_encoders ops that
was directly mapped to the drm_encoder helper funcs.
So now exynos DRM uses struct drm_encoder directly, this removes
completely the struct exynos_drm_encoder.
v2: add empty .mode_fixup() and .mode_set() to DSI and DPI to avoid null
pointer.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
As we are removing the exynos encoder move the encoder setup operation
directly inside the exynos_drm_load()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This functions was just hiding the encoder and connector creation in
a way that was less clean than if we get rid of it. For example,
exynos_encoder ops had .create_connector() defined only because we were
handing off the encoder and connector creation to
exynos_drm_create_enc_conn(). Without this function we can directly call
the create_connector function internally in the code, without the need of
any vtable access.
It also does some refactoring in the code like creating a bind function
for dpi devices.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
.commit() is not used anymore, Exynos encoders now follow the
.enable()/.disable() semantics from drm atomic core, so remove this
callback.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
exynos_dp_commit() was getting called twice by exynos encoder core, once
inside the .enable() call and another time by .commit() itself.
The remove of the second call caused the wake of a bug, the operations
orders inside exynos_dp_commit was wrong and we had to move
exynos_dp_start_video() to be the last operation in there.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
hdmi_commit() was getting called twice by exynos encoder core, once inside
the .enable() call and another time by .commit() itself.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This struct was just representing encoder information, it was a member of
struct exynos_drm_encoder, so any code trying to access encoder data would
have to go through the encoder struct, get the display struct and then get
the data it want.
During this patchset we also realized that the only data
exynos_drm_encoder needs to store is the drm_encoder parent and the
exynos_drm_encoder_ops.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All CRTCs can only be LCD, HDMI or VIDI, so basically all CRTCs will be a
possible CRTCs. This patch removes an extra function with switch that was
only checking if the CRTC type was one of those three above.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
These two display_ops are not used anywhere, remove them.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
phy_power_on() and phy_power_off() already checks for NULL pointer.
This patch removes the wrappers exynos_dp_phy_init() and
exynos_dp_phy_exit() since the only think they were doing was a check for
NULL phy.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The DRM Core doesn't have a dpms() operation anymore, everything
now is enable() or disable().
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Instead of blindly ignore the return value of enable_vblank return it
to the upper DRM layer for error handling.
Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Rename crtc_{widht,height} to crtc_{w,h} and src_{width,height} to
src_{w,h} to make it similar to the atomic state names.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Now after the move to use drm_plane_state directly struct drm_plane_state
has many unused fields, along with others that weren't used before the
plane state change. Thus remove them all.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
For some fields the use of struct exynos_drm_plane filled with data from
the plane state just creates a source of duplicated information and
overhead. Here we change the crtc drivers to access the plane state
directly simplifying the code by not relying on a exynos internal struct.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We already have the plane pointer in before calling .update_plane() or
disable_plane() so pass it directly to those calls avoiding a new
conversion from zpos to struct exynos_drm_plane.
v2: don't remove check for suspended in FIMD (comment by Joonyoung)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The same check is placed twice in fimd/decon_update_plane(), remove
one of them.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Get rid of legacy DRM vblank function that are less clear to use.
The new ones basically requires only the crtc as parameters.
It also clean ups exynos_drm_crtc_finish_pageflip() parameters as a
consequence.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Instead of giving -1 to as arg to drm_send_vblank_event() pass the
correct pipe number to it.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This is simplest solution about reported problem[1]. It's no problem to
clear channel only when iommu is enabled, if we consider that we cannot
recognize iommu errors when iommu is disabled and it have been valid
until now. But this cannot be nice solution.
[1] https://lkml.org/lkml/2015/7/21/404
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already drm_iommu_attach_device checks whether support iommu internally.
It should clear channels always regardless iommu support. We didn't know
because we can detect the problem when iommu is enabled, so we don't
have to use drm_iommu_attach_device_if_possible and then we can remove
drm_iommu_attach_device_if_possible and clear_channels function pointer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The vidi is virtual kms driver and now it is registered earlier than
actual hw kms drivers, so it will occupy crtc index 0. Some users
assume the condition yet that actual hw kms driver has crtc index 0.
It may or may not be matter but let's arrange register order.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Driver uses only VSYNC interrupts, so we need to cache VSYNC bit state only.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The driver uses bool protected by mutex to track power state.
The patch replaces this combo with single bit and atomic bitops.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already drm_iommu_attach_device and drm_iommu_detach_device check
whether support iommu internally, so we don't have to call
is_drm_iommu_supported before call them.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
If CONFIG_ARM_DMA_USE_IOMMU is disable, CONFIG_DRM_EXYNOS_IOMMU also is
disable. When CONFIG_DRM_EXYNOS_IOMMU is disable,
is_drm_iommu_supported() returns always false, so we can remove to use
ifdef CONFIG_ARM_DMA_USE_IOMMU in is_drm_iommu_supported().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The unique results of all the combination of rotation and flip can
be represented by just 8 states. This patch handles all the combination
correctly.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch removes intermediate struct for HDMIv14 register configuration,
instead registry values are calculated on the fly.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch removes intermediate struct for HDMIv13 register configuration,
instead registry values are calculated on the fly.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch removes redundant fields from hdmi_conf_regs. Their values
can be calculated from current_mode. This patch is the first step to remove
whole hdmi_conf_regs structure.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch replaces duplicated driver data fields in private context with
pointer to driver data. It also simplifies driver data lookup code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Most of the code is called by drm core framework, so it is already synchronized.
The only async function is irq routine which only calls drm framework so it
does not need to be synchronized.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
GPIO is tested only in hdmi_detect, so there is no reason to set it in
other places and to preserve its value in context.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
s5p_hdmi_platform_data were used before device tree introduction.
As HDMI driver is DT only we can drop this struct completely.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Once pm_runtime_set_active() gets called, the kernel assumes that given
device has already enabled runtime pm and will call pm_runtime_suspend()
without matching pm_runtime_resume(). In case of DRM FIMC IPP driver,
this will result in calling clk_disable() without respective call to
clk_enable(). This patch removes call to pm_runtime_set_active() to
ensure that pm_runtime_suspend/resume calls will match.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
INT_EN cache field was updated only by mixer_enable_vblank.
The patch adds update also by mixer_disable_vblank function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The driver used incorrect flags to clear interrupt status.
The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
edid returned by drm_get_edid should be freed.
The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The bits for rotation are not used as exclusively. So GSC_IN_ROT_270 can
not be used for swap detection. The definition of it is same with
GSC_IN_ROT_MASK. It is enough to check GSC_IN_ROT_90 bit is set or not to
check whether width / height size swapping is needed.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
With more platforms supported, the DSI host
configuration array keeps expanding. This change
moves those to a separate dsi_cfg module.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
On a certain platform, only one type of DSI PHY is used.
This change allows the user to only compile the PHY type
which is being used.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change moves each PHY type specific code into
separate files.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We are not checking the return value from msm_dsi_phy_disable().
Change the return type to void.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The bit position to configure source PLL will change
on new types of PHYs. The caller should pass down
this information.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pending interrupt status needs to be cleared before enable the
interrupt. Otherwise it's possible to get a pending interrupt instead
of an incoming interrupt.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 SSPPs can flip the input source horizontally or vertically.
This change is to add this support to MDP5 planes.
v1: Initial change
v2: Use existing "rotation" property instead of creating msm specific
properties. In order to be compatiable with legacy non-atomic
set_property, switch to drm_atomic_helper_plane_set_property
helper function.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Prepare the panel before it's enabled and un-prepare after disable, this
will make sure that the regulators are switched on and off correctly.
Tested it on APQ8064 based IFC6410 with panel.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi bridge ops call drm_panel functions to set up the connected
drm_panel. Add checks to make sure these aren't called when we're
connected to an external bridge.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are platforms where the DSI output can be connected to another
encoder bridge chip (DSI to HDMI, DSI to LVDS etc).
Add support for external bridge support to the dsi driver. We assume that
the external bridge chip would be of the type drm_bridge. The dsi driver's
internal drm_bridge (msm_dsi->bridge) is linked to the external bridge's
drm_bridge struct.
In the case we're connected to an external bridge, we don't need to create
and manage a connector within our driver, it's the bridge driver's
responsibility to create one.
v2:
- Move the external bridge attaching stuff to dsi manager to make things
cleaner.
- Force the bridge to connect to a video mode encoder for now (the dsi
mode flags may have not been populated by modeset_init)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a helper msm_dsi_device_connected() which checks whether we have a
device connected to the dsi host or not. This check gets messy when we
have support external bridges too. Having an inline function makes it
more legible.
For now, the check only consists of msm_dsi->panel being non-NULL. Later,
this will check if we have an external bridge or not.
This helper isn't used in dsi_connector related code as that's specific
to only when a drm_panel is connected.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently support only panels connected to dsi output. We're going to
also support external bridge chips now.
Change 'panel_node' to 'device_node' in the struct msm_dsi_host and
'panel_flags' to 'device_flags' in msm_dsi. This makes things sound a
bit more generic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Platforms containing only DSI video mode devices don't need a TE gpio.
Make TE gpio optional.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently get the output connected to LVDS by looking for a phandle
called 'qcom,lvds-panel' under the mdp DT node.
Use the more standard of_graph approach to create an lvds output port,
and retrieve the panel node from the port's endpoint data.
v3
- Fix return value checks of of_graph_* calls.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi host looks for the connected panel node by parsing for a child
named 'panel'. This hierarchy isn't very flexible. The connected
panel is forced to be a child to the dsi host, and hence, a mipi dsi
device. This isn't suitable for dsi devices that don't use mipi dsi
as their control bus.
Follow the of_graph approach of creating ports and endpoints to
represent the connections between the dsi host and the panel connected
to it. In our case, the dsi host will only have one output port, linked
to the panel's input port.
Update DT binding documentation with device graph usage info.
v3:
- Fix return value checks of of_graph_* calls.
- Don't make port a mandatory DT property
- Fix defer check when no panel node specified
- Rename parse_dt func to align with other dsi_host funcs
Reviewed-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Decrement device node refcount if of_get_child_by_name is successfully
called.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
AHB clock should be enabled before accessing registers during
enable/disable_vblank(). Since these 2 callbacks are called in
atomic context while clk_prepare may cause thread sleep, a work
is scheduled to control vblanks.
v2: fixup spinlock initialization
Signed-off-by: Hai Li <hali@codeaurora.org>
[add comment about cancel_work_sync() before drm_irq_uninstall()]
Signed-off-by: Rob Clark <robdclark@gmail.com>
msm8x74v1 has different MDP5 version (v1.0) from msm8x74v2 (v1.2).
Add a separate config data to support msm8x74v1.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to add planes which use DMA pipes for MDP5.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
[slight comment adjust to s/Construct public planes/Construct video
planes/ since DMA planes are public planes too, they just can't scale
or CSC]
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP planes can be implemented using different type of HW pipes,
RGB/VIG/DMA pipes for MDP5 and RGB/VG/DMA pipes for MDP4. Each type
of pipe has different HW capabilities such as scaling, color space
conversion, decimation... Add a variable in plane data structure
to specify the difference of each plane which comes from mdp5_cfg data
and use it to differenciate the plane operation.
V1: Initial change
V2: Fix a typo in mdp4_kms.h
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add packed YUV422 and planar YUV420 formats to MDP supported
formats.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Newer MDP5 uses 2 shared memory pool clients for certain YUV formats.
For example, if VIG0 is used to fetch data in YUYV format, it will use
VIG0_Y for Y component, and VIG0_Cr for UV packed.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
[rebase]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
This makes it easy to determine if a format is YUV. The old
method of using chroma sample type incorrectly marks YUV444 as
RGB format.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
[rebase]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this to simplify the driver. Furthermore this is one caller less
that stops us making the flags argument to gpiod_get*() mandatory.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reset DSI PHY silently changes its PLL registers to reset status,
which will make cached status in clock driver invalid and result
in wrong output rate of link clocks. The current restore mechanism
in DSI PLL does not cover all the cases. This change is to recover
PLL status after PHY reset to match HW status with cached status
in clock driver.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi_destroy() function was called in two cases by the dsi_init() function
during error handling even if the passed variable contained a null pointer.
* This implementation detail could be improved by adjustments for jump
targets according to the Linux coding style convention.
* Drop an unnecessary initialisation for the variable "msm_dsi" then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[add couple missing ERR_PTR()'s]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi_destroy() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change takes advantage of a HW feature that synchronize
flush operation on CTL1 to CTL0, to keep dual DSI pipes in
sync.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In MDP5, CTL contains information of the whole pipeline whose
output goes down to a display interface. In various cases, one
interface may require 2 CRTCs, but only one CTL. Some interfaces
also require to use certain CTLs.
Instead of allocating CTL for each active CRTC, this change is to
associate a CTL with each interface.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change is to add properties alpha/zpos/blend_mode to mdp5 plane
for alpha blending operation to generate the blended output.
v1: Initial change
v2: Change "premultilied" property to enum (Rob's comment)
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
[Don't actually expose alpha/premultiplied props to userspace yet
pending a chance for discussion and some userspace to exercise it]
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was a hold-over from the pre-atomic days and legacy userspace that
only understood CRTCs. Fortunately we don't have any properties, so
this doesn't change anything. But before we start growing some plane
properties, we should fix this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY errors are falsely reported whenever a dsi error occurs. This is
because DSI_DLN0_PHY_ERR isn't only used as a status register, but also
used to mask PHY errors. Currently, we end up reading the mask bits too
and therefore always report errors.
Ignore the register mask bits and check for only the status/clear bits.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The maximum output width of one pipeline depends on the LayerMixer's
capability. It may be different on each target. Also, MDP5 doesn't
have vertical limitation in one frame, as long as the pixel clock
can be supported.
This change obtains the maximum LM resolution from configuration
table and treat it as the whole pipe's limitation for MDP5. The size
limit on MDP4 is not changed.
Signed-off-by: Hai Li <hali@codeaurora.org>
For all of these devices, msm89xy was the lead chip, so standardize the
compatible names to align with convention used by rest of the qcom/msm
drivers.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the MDP and HDMI support for msm8x94.
Note that HDMI PHY registers are not being accessed anymore from
the driver.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[rename compatible s/8x94/8994/ since preference is to not trust the
marketing folks who invent chip #'s but instead name things after the
lead chip.. we should rename some 80XY to 89XY to standardize on the
lead chip but leave that for another patch. Also, update dt bindings
doc]
Signed-off-by: Rob Clark <robdclark@gmail.com>
->reset() currently only accesses HDMI core registers, and yet it
is located in hdmi_phy*. Since no PHY registers are being
accessed during ->reset(), it would be better to bring that
function in hdmi core module where HDMI core registers are
usually being accessed.
This will also help for msm8x94 for which no PHY registers
accesses are done (->phy_init == NULL) but the HDMI PHY reset
from HDMI core still needs to be done.
Note:
SW_RESET_PLL bit is not written in hdmi_phy_8x60_reset(); this
write should not affect anything if the corresponding field is
not writable.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[fixed warning about unused 'phy' in hpd_enable() while merging]
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI controller on msm8x94 is version 1.3, which requires different
power supplies and works with 20nm DSI PHY. This change is to add
the basic support for this version.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some targets use pinctrl framework to configure some
pins. This change allows DSI driver to set default and
sleep pinctrl status.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current term of *dual panel* in DSI driver code causes confusion.
It is supposed to indicate the panel using two DSI links. Rename it
to *dual DSI*.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The source PLL to be used by each DSI PHY should be decided by
DSI manager based on dual DSI information, while the register
programming to select PLL is different from one type of PHY to
another. This change adds the H/W difference to PHY configuration
and updates the interface between DSI manager and PHY.
With this change, PLL selection can be supported on different
targets.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
single MST fixes from Maarten.
* tag 'topic/drm-fixes-2015-08-14' of git://anongit.freedesktop.org/drm-intel:
drm/dp/mst: Remove port after removing connector.
three display fixes for Intel.
* tag 'drm-intel-fixes-2015-08-14' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Commit planes on each crtc separately.
drm/i915: calculate primary visibility changes instead of calling from set_config
drm/i915: Only dither on 6bpc panels
Release all blocks after the pipe is disabled, even when vsync
didn't happen in some error cases. Allow requesting SMB multiple
times before configuring to hardware, by releasing blocks not
programmed to hardware yet for shrinking case.
This fixes a potential leak of shared memory pool blocks.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The atomic commit cannot easily undo and return an error once the
state is swapped. Change to uninterruptible wait, and ignore the
timeout error.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp4_get_frame_format() can dereference a drm_framebuffer when it's NULL.
Call it in mdp4_plane_mode_set only when we know fb is non-NULL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to return a new sgt, since the caller takes ownership of it.
Reported-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Put the Kconfig entries for bridge drivers into a separate menu so that
they are automatically grouped and don't clutter up the top-level menu.
While at it, move the bridge menu towards the end of the top-level menu
where the panel menu is already located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG4573 is used on the LG LCD LB043WV2-SD01, an industrial 4.3" TFT
panel with SPI control interface.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Okaya RS800480T-7X0GP to the DRM simple panel
driver.
The RS800480T-7X0GP is a WVGA (800x480) panel with an 18-bit parallel
LCD interface. It supports pixel clocks in the range of 30-40 MHz.
This panel details can be found at:
http://boundarydevices.com/product/7-800x480-display/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the NEC NL4827HC19-05B 480x272 panel to the DRM
simple panel driver.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[treding@nvidia.com: add .bpc field for panel]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B080UAN01 is an 8.0" WUXGA TFT LCD panel connected using four
DSI lanes. It can be supported by the simple-panel driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the data sheet, the minimum horizontal blanking interval
is 54 clocks (1 + 52 + 1), but tests with a Nitrogen6X have shown the
minimum working horizontal blanking interval to be 60 clocks.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The bus format both specifies the bpc and the way the individual bits get
serialized into the 7 LVDS timeslots.
While the is only one standard mapping for 6 bpc and so the driver could
infer the bit mapping from the bpc alone, there are more options for the
8 bpc case which makes specifiying the bus format mandatory.
To keep things consistent across panels and to set a precedent for new
panel additions add the proper bus format.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use vendor prefixes for Kconfig symbols and filenames. This should make
it easier to identify the various bridge drivers and to organize the
directory.
v2: fix object name for dw-hdmi (Fabio Estevam)
Signed-off-by: Thierry Reding <treding@nvidia.com>
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-intel-fixes because a bunch of atomic patch backporting
we had to do lead to horrible conflicts.
Conflicts:
drivers/gpu/drm/drm_crtc.c
Just a bit of context conflict between -next and -fixes.
drivers/gpu/drm/i915/intel_atomic.c
drivers/gpu/drm/i915/intel_display.c
Atomic conflicts, always pick the code from -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
There is currently conflicting documentation on which steppings the
workaround is needed, up to C vs. forever. However there is post-C
stepping hardware that doesn't report port presence on DDI A, leading to
black screen on eDP. Assume the strap isn't connected, and try to enable
DDI A on these machines. (We'll still check the VBT for the info in DDI
init.)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP spec requires the checksum of the last block read to be written
when replying to TEST_EDID_READ. This patch fixes the current code
to do the same.
v2: removed loop for jumping blocks and performed direct addition
as recommended by Daniel
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevent leaking the if scoping by containing the WA_REG
macro inside its own scope.
Reported-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter an allocation failure during ppggt creation (trivial
even with 16Gib+ RAM!), we need to remove the dead context from the
fpriv->context_idr along with the references.
gem_exec_ctx: page allocation failure: order:0, mode:0x8004
CPU: 3 PID: 27272 Comm: gem_exec_ctx Tainted: G W 4.2.0-rc5+ #37
0000000000000000 ffff880086ff7a78 ffffffff816b947a ffff88041ed90038
0000000000008004 ffff880086ff7b08 ffffffff8114b1a5 ffff880086ff7ac8
ffffffff8108d848 0000000000000000 ffffffff81ce84b8 0000000000000000
Call Trace:
[<ffffffff816b947a>] dump_stack+0x45/0x57
[<ffffffff8114b1a5>] warn_alloc_failed+0xd5/0x120
[<ffffffff8108d848>] ? __wake_up+0x48/0x60
[<ffffffff8114e0ed>] __alloc_pages_nodemask+0x73d/0x8e0
[<ffffffffc0472238>] ? i915_gem_execbuffer2+0x148/0x240 [i915]
[<ffffffffc0474240>] __setup_page_dma+0x30/0x110 [i915]
[<ffffffffc0477f61>] gen8_ppgtt_init+0x31/0x2f0 [i915]
[<ffffffffc04785e0>] i915_ppgtt_init+0x30/0x80 [i915]
[<ffffffffc0478928>] i915_ppgtt_create+0x48/0xc0 [i915]
[<ffffffffc046c9c2>] i915_gem_create_context+0x1c2/0x390 [i915]
[<ffffffffc046d9cb>] i915_gem_context_create_ioctl+0x5b/0xa0 [i915]
leading to an oops in i915_gem_context_close. Also note that this
benchmark should not be running out of memory in the first place...
Testcase: igt/benchmark/gem_exec_ctx -b create # ppgtt >= 2
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The IOMMU for Intel graphics has historically had many issues resulting
in random GPU hangs. Lets include its status when capturing the GPU hang
error state for post-mortem analysis.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If idle to active bit is set, the rest of the fields
in CSQ are not valid.
Bail out early if this is the case in order to prevent
rest of the loop inspecting stale values.
This was found by Bspec/code inspection. Doesn't seem to fix any of
the known issues.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
[danvet: Add note about how this was found.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I started digging this when I noticed that the BDW code was just
reserving 1mb by coincidence since it was reading reserved fields.
Then I noticed we didn't have any values set for SNB and earlier, and
that the HSW sizes were wrong. After that, I noticed that the reserved
area has a specific start, and may not exactly end where the stolen
memory ends. I also noticed the base pointer can be zero. So I decided
to just write a single patch fixing everything instead of 20 patches
that would be much harder to review.
This patch may solve random stolen memory corruption/problems on
almost all platforms. Notice that since this is always dealing with
the top of the stolen memory, the problems are not so easy to
reproduce - especially since FBC is still disabled by default.
One of the major differences of this patch is that we now look at both
the size and base address. By only looking at the size we were
assuming that the reserved area was always at the very top of
stolen, which is not always true.
After we merge the patch series that allows user space to allocate
stolen memory we'll be able to write IGT tests that maybe catch the
bugs fixed by this patch.
v2:
- s/BIOS reserved/stolen reserved/g (Chris)
- Don't DRM_ERROR if we can't do anything about it (Chris)
- Improve debug messages (Chris).
- Use the gen7 version instead of gen6 on HSW. Tom found some
documentation problems, so I think with gen7 we're on the safer
side (Tom).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register needs to be updated with masked writes.
This was found by code inspection and comparison with Bspec and
doesn't seem to fix any known issue.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Add note about impact.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we encounter frequent problems with dp aux channel
communications, we end up spamming the dmesg with the
exact similar trace and status.
Inject a new backtrace only if we have new information
to share as otherwise we flush out all other important
stuff.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-EDEADLK has special meaning in atomic, but get_fence may call
i915_find_fence_reg which can return -EDEADLK.
This has special meaning in the atomic world, so convert the error
to -EBUSY for this case.
Changes since v1:
- Add comment in the code.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The rest will be a noop anyway, since without modeset there will be
no updated dplls and no modeset state to update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are no more users, byebye!
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that everything's atomic, checking encoder->base.crtc is enough.
This function doesn't have the locks to dereference crtc->state, but
stealing an encoder bound to any crtc is probably enough reason to warn.
Changes since v1:
- Commit message.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
connectors_active will be removed, so just calculate this instead.
Changes since v1:
- Look for the right pointer in intel_sanitize_encoder.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is now done completely atomically.
Keep connectors_active for now, but make it mirror crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of allocating pipe_config on the stack use the old
crtc_state, it's only going to freed from this point on.
All crtc' are now only checked once during modeset,
because false positives can happen with encoders after
dpms changes and to limit the amount of errors for 1 failure.
Changes since v1:
- crtc_state -> old_crtc_state
- state -> old_state
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Connectors are updated atomically now, so the only interaction
with the encoder is through base.crtc.
If it's NULL the encoder's not part of any crtc, and if it's
not NULL then active should be equal to crtc_state->active.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is handled by the atomic core now, no need to check this for ourself.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now dpms callbacks can still fiddle with the connector state,
but it can only turn connectors off.
This is remediated by only checking crtc->state->active when the
connector is active, and ignore crtc->state->active when the
connector is off.
connectors_active is no longer checked, and will be removed later
in this series together with dpms.
Another check for !encoder->crtc is performed by check_encoder_state
too, so it can be removed.
Changes since v1:
- Add commit message.
- rename state to old_state.
- Move deletion of mst_port check to mst patch.
Changes since v2:
- Fix a null pointer dereference on MST now hw readout is fixed.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fully remove the MST connector from the atomic state, and remove the
early returns in check_*_state for MST connectors.
With atomic the state can be made consistent all the time.
Thanks to Sivakumar Thulasimani for the idea of using
drm_atomic_helper_set_config.
Changes since v1:
- Remove the MST check in intel_connector_check_state too.
Changes since v2:
- Use drm_atomic_helper_set_config.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First step in removing dpms and validating atomic state.
There can still be a mismatch in the connector state because the dpms
callbacks are still used, but this can not happen immediately after a modeset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Set connectors_changed to force a modeset if the panel fitter's force
enabled on eDP.
Changes since v1:
- Use connectors_changed instead of active_changed because it's a
routing update.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two small bug fixes for the code you pulled for 4.3:
- Used a SHIFT define instead of a MASK define to check if a bit is turned on
when destroying hqd. Luckily, this is in gfx7 interface file with amdgpu,
which was used only for bring-up purposes of amdgpu, so no real effect on
a running system
- Used a logical AND instead of a bitwise AND operator, when initializing
sdma virtual memory when using SDMA queues
* tag 'drm-amdkfd-next-fixes-2015-08-05' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: fix bug when initializing sdma vm
drm/amdgpu: fix bug when amdkfd destroys hqd
This serie of patches fix minor bugs around how driver sub-components are
bind and planes z-ordering.
The main part is about atomic support: using more atomic helpers allow us
to simplify the code (~300 lines removed) and to ahve a better match between
drm concepts (planes and crtc) and hardware split.
[airlied: fixed up conflict in atomic code]
* 'drm-sti-next-atomic-2015-08-11' of http://git.linaro.org/people/benjamin.gaignard/kernel:
drm/sti: atomic crtc/plane update
drm/sti: rename files and functions
drm/sti: code clean up
drm/sti: fix dynamic z-ordering
drm: sti: fix sub-components bind
This reverts commit 1addc12648
This commit seems to cause crashes in gk104_fifo_intr_runlist() by
returning 0xbad0da00 when register 0x2a00 is read. Since this commit was
intended for GM20B which is not completely supported yet, let's revert
it for the time being.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This addresses two issues that cause problems with viewperf maya-03 in
situation with memory pressure.
The first issue causes attempts to unreserve buffers if batched
reservation fails due to, for example, a signal pending. While previously
the ttm_eu api was resistant against this type of error, it is no longer
and the lockdep code will complain about attempting to unreserve buffers
that are not reserved. The issue is resolved by avoid calling
ttm_eu_backoff_reservation in the buffer reserve error path.
The second issue is that the binding_mutex may be held when user-space
fence objects are created and hence during memory reclaims. This may cause
recursive attempts to grab the binding mutex. The issue is resolved by not
holding the binding mutex across fence creation and submission.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The likelihood of getting a large number of panel drivers from different
vendors is quite high. Add a prefix to the two existing Samsung panel
drivers to set a guideline for future patch submissions. Using vendor
prefixes consistently should allow a cleaner organization of the tree.
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that the PTN3460 driver has been rewritten as a proper I2C driver
and there is infrastructure to hook up the bridge with a DRM device, it
is no longer necessary to have this dependency to ensure the correct
build mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR1 introduced on Tegra210 supports HDMI 2.0 and DisplayPort. Add
HDMI support and name the debugfs node after the type of SOR. The SOR
introduced with Tegra124 is known simply as "sor", whereas the
additional SOR found on Tegra210 is known as "sor1".
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR found on Tegra210 is very similar to the version found on
Tegra124, except that it no longer supports LVDS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move all code into the new canonical ->disable() and ->enable() helper
callbacks so that they play extra nice with atomic DPMS.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to restore DPMS with atomic mode-setting, move all code from
the ->mode_set() callback into ->enable(). At the same time, rename the
->prepare() callback to ->disable() to use the names preferred by atomic
mode-setting. This simplifies the calling sequence and will allow DPMS
code to use runtime PM in subsequent patches.
While at it, remove the enabled field that hasn't been used since the
demidlayering of the output drivers done in preparation for the atomic
mode-setting conversion.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of duplicating most of the code to set up a debugfs file, use
the existing DRM core debugfs infrastructure instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The head state registers are per head, so they must be properly indexed.
This has worked fine so far because all boards with eDP use it as the
primary output, so it is very likely to end up attached to head 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The data structure is always only read, never written, and can hence be
referred to by a const pointer.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tearing down debugfs support, make sure to reset the fields to NULL
in the correct order, otherwise the debugfs root will not be properly
removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM minor is needed to teardown debugfs, so it needs to be tracked
to prevent a crash on driver removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the SOR device fails, output proper error messages to help
diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TRM lists indexed registers without an underscore to separate name
from index. Use that convention in the driver for consistency.
While at it, rename some of the field names to the names used in the
TRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DPAUX isn't attached to an SOR the interrupts are not useful.
This also prevents a race that could potentially cause a crash on driver
removal.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DPAUX code paths already configure the pads in AUX mode, but there
is no way to reconfigure them in I2C mode for HDMI (the DPAUX module is
unused in that case). Enabling the pads in I2C mode by default is the
quickest way to support HDMI. Eventually this may need an explicit call
in the user drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When probing the dpaux device fails, output proper error messages to
help diagnose the cause of the failure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra132 to Tegra210, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra124 to Tegra132, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI host controller hasn't changed from Tegra114 to Tegra124, but
different characterization parameters may be required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In video modes without sync pulses, the horizontal back-porch needs to
include the horizontal sync width.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The call to platform_driver_register() will already set up the .owner
field, so there's no need to do it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The horizontal pulse enable bits are named H_PULSE{0,1,2}_ENABLE in the
TRM. Modify the driver to use the same naming for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Record interrupt statistics, such as the number of frames and VBLANKs
received and the number of FIFO underflow and overflows.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Request a syncpoint for display prior to registering the host1x client.
This will ensure that the syncpoint will be acquired when the KMS driver
initializes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Upon driver load, reset the VBLANK machinery to off to reflect the
hardware state. Since the ->reset() callback is called from the initial
drm_mode_config_reset() call, move the latter after the VBLANK machinery
initialization by drm_vblank_init().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Keep track of the number of users of DSI and CSI pads and power down the
regulators that supply the bricks when all users are gone.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some changes are needed to the configuration settings for some lanes. In
addition, the clock lanes for the CSI pads can no longer be calibrated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
While Tegra132 has the same pads as Tegra124, some configuration values
need to be programmed slightly differently.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before starting a new calibration cycle, make sure to clear the current
status by writing a 1 to the various "calibration done" bits.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use more consistent names for the clock lane configuration registers and
fix the offset of the upper clock lane configuration register for the
first DSI pad.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Parameterize more of the register programming to accomodate for changes
required by future SoC generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch is based on the upstream commit 5ac1c4bcf0 and amended
for v4.2 to make sure it works as intended.
Repeated calls to begin_crtc_commit can cause warnings like this:
[ 169.127746] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:616
[ 169.127835] in_atomic(): 0, irqs_disabled(): 1, pid: 1947, name: kms_flip
[ 169.127840] 3 locks held by kms_flip/1947:
[ 169.127843] #0: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffff814774bc>] __drm_modeset_lock_all+0x9c/0x130
[ 169.127860] #1: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffff814774cd>] __drm_modeset_lock_all+0xad/0x130
[ 169.127870] #2: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffff81477178>] drm_modeset_lock+0x38/0x110
[ 169.127879] irq event stamp: 665690
[ 169.127882] hardirqs last enabled at (665689): [<ffffffff817ffdb5>] _raw_spin_unlock_irqrestore+0x55/0x70
[ 169.127889] hardirqs last disabled at (665690): [<ffffffffc0197a23>] intel_pipe_update_start+0x113/0x5c0 [i915]
[ 169.127936] softirqs last enabled at (665470): [<ffffffff8108a766>] __do_softirq+0x236/0x650
[ 169.127942] softirqs last disabled at (665465): [<ffffffff8108ae75>] irq_exit+0xc5/0xd0
[ 169.127951] CPU: 1 PID: 1947 Comm: kms_flip Not tainted 4.1.0-rc4-patser+ #4039
[ 169.127954] Hardware name: LENOVO 2349AV8/2349AV8, BIOS G1ETA5WW (2.65 ) 04/15/2014
[ 169.127957] ffff8800c49036f0 ffff8800cde5fa28 ffffffff817f6907 0000000080000001
[ 169.127964] 0000000000000000 ffff8800cde5fa58 ffffffff810aebed 0000000000000046
[ 169.127970] ffffffff81c5d518 0000000000000268 0000000000000000 ffff8800cde5fa88
[ 169.127981] Call Trace:
[ 169.127992] [<ffffffff817f6907>] dump_stack+0x4f/0x7b
[ 169.128001] [<ffffffff810aebed>] ___might_sleep+0x16d/0x270
[ 169.128008] [<ffffffff810aed38>] __might_sleep+0x48/0x90
[ 169.128017] [<ffffffff817fc359>] mutex_lock_nested+0x29/0x410
[ 169.128073] [<ffffffffc01635f0>] ? vgpu_write64+0x220/0x220 [i915]
[ 169.128138] [<ffffffffc017fddf>] ? ironlake_update_primary_plane+0x2ff/0x410 [i915]
[ 169.128198] [<ffffffffc0190e75>] intel_frontbuffer_flush+0x25/0x70 [i915]
[ 169.128253] [<ffffffffc01831ac>] intel_finish_crtc_commit+0x4c/0x180 [i915]
[ 169.128279] [<ffffffffc00784ac>] drm_atomic_helper_commit_planes+0x12c/0x240 [drm_kms_helper]
[ 169.128338] [<ffffffffc0184264>] __intel_set_mode+0x684/0x830 [i915]
[ 169.128378] [<ffffffffc018a84a>] intel_crtc_set_config+0x49a/0x620 [i915]
[ 169.128385] [<ffffffff817fdd39>] ? mutex_unlock+0x9/0x10
[ 169.128391] [<ffffffff81467b69>] drm_mode_set_config_internal+0x69/0x120
[ 169.128398] [<ffffffff8119b547>] ? might_fault+0x57/0xb0
[ 169.128403] [<ffffffff8146bf93>] drm_mode_setcrtc+0x253/0x620
[ 169.128409] [<ffffffff8145c600>] drm_ioctl+0x1a0/0x6a0
[ 169.128415] [<ffffffff810b3b41>] ? get_parent_ip+0x11/0x50
[ 169.128424] [<ffffffff811e9ab8>] do_vfs_ioctl+0x2f8/0x530
[ 169.128429] [<ffffffff810d0fcd>] ? trace_hardirqs_on+0xd/0x10
[ 169.128435] [<ffffffff812e7676>] ? selinux_file_ioctl+0x56/0x100
[ 169.128439] [<ffffffff811e9d71>] SyS_ioctl+0x81/0xa0
[ 169.128445] [<ffffffff81800697>] system_call_fastpath+0x12/0x6f
Solve it by using the newly introduced drm_atomic_helper_commit_planes_on_crtc.
The problem here was that the drm_atomic_helper_commit_planes() helper
we were using was basically designed to do
begin_crtc_commit(crtc #1)
begin_crtc_commit(crtc #2)
...
commit all planes
finish_crtc_commit(crtc #1)
finish_crtc_commit(crtc #2)
The problem here is that since our hardware relies on vblank evasion,
our CRTC 'begin' function waits until we're out of the danger zone in
which register writes might wind up straddling the vblank, then disables
interrupts; our 'finish' function re-enables interrupts after the
registers have been written. The expectation is that the operations between
'begin' and 'end' must be performed without sleeping (since interrupts
are disabled) and should happen as quickly as possible. By clumping all
of the 'begin' calls together, we introducing a couple problems:
* Subsequent 'begin' invocations might sleep (which is illegal)
* The first 'begin' ensured that we were far enough from the vblank that
we could write our registers safely and ensure they all fell within
the same frame. Adding extra delay waiting for subsequent CRTC's
wasn't accounted for and could put us back into the 'danger zone' for
CRTC #1.
This commit solves the problem by using a new helper that allows an
order of operations like:
for each crtc {
begin_crtc_commit(crtc) // sleep (maybe), then disable interrupts
commit planes for this specific CRTC
end_crtc_commit(crtc) // reenable interrupts
}
so that sleeps will only be performed while interrupts are enabled and
we can be sure that registers for a CRTC will be written immediately
once we know we're in the safe zone.
The crtc->config->base.crtc update may seem unrelated, but the helper
will use it to obtain the crtc for the state. Without the update it
will dereference NULL and crash.
Changes since v1:
- Use Matt Roper's commit message.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This should be much cleaner, with the same effects.
(cherry picked for v4.2 from commit fb9d6cf8c2)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=90398
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In
commit d328c9d78d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
we started to select the pipe bpp from sink capabilities and not from
the primary framebuffer - that one might change (and we don't want to
incur a modeset) and sprites might contain higher bpp content too.
We also selected dithering on a 8 bpc screen displaying a 24bpp rgb
primary, because pipe_bpp is 24 for such a typical 8 bpc sink, but since
the commit mentioned above, base_bpp is always the absolute maximum
supported by the hardware, e.g., 36 bpp on my Ironlake chip. Iow. the
only way to not get dithering would have been to connect a deep color 12
bpc display, so pipe_bpp == 36 == base_bpp.
Hence only enable dithering on 6bpc screens where we difinitely and
always want it.
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Reported-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Updating and fixing copyright headers.
Bump version minor to signal vgpu10 support.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Add support for vgpu10 queries. Functional- and formatting fixes.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Add support for SVGA_3D_CMD_DX_BUFFER_COPY and
SVGA_3D_CMD_DX_PRED_COPY_REGION
Signed-off-by: Neha Bhende <nbhende@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Implement support for a couple of missing commands and fix a command parser
error path. Also fix uninitialized devcaps and surface size computation.
Signed-off-by: Charmaine Lee <charmainel@vmware.com>
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Initial DX support.
Co-authored with Sinclair Yeh, Charmaine Lee and Jakob Bornecrantz.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Charmaine Lee <charmainel@vmware.com>
Add DX includes and move all device includes to a separate directory.
Co-authored with Thomas Hellstrom, Charmaine Lee and above all,
the VMware device team.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Charmaine Lee <charmainel@vmware.com>
This patch fixes two issues. One, when a surface is a proxy for a DMA
buffer, it holds an extra reference that needs to be cleared.
Two, when fbdev is enabled, we need to unpin the framebuffer before
unloading the driver. This is done by a call to vmw_fb_off().
v2
Moved unreferencing surface to from vmw_framebuffer_surface_destroy()
to vmw_kms_new_framebuffer()
Added "struct vmw_framebuffer *vfb = NULL;" to silence a compiler
warning.
Removed error checking after calling vmw_surface/dmabuf_reference()
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
On older hardware, texture max width and height is not available, so set
it to something reasonable, like 8192.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
For a Screen Target capable display device, the display topology is
limited by SVGA_REG_MAX_PRIMARY_BOUNDING_BOX_MEM. Two values are
checked against this limit:
1. Size of the bounding box enclosing all the displays, and
2. Size of the total number of displays, e.g. framebuffers
The limitations above mean we do not have exact max width and
height for the topology. The best current option is to set those to
the maximum texture width/height.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Instead of using the legacy VBLANK API, use the new KMS API. This is
part of an effort to convert all existing users so that the KMS API can
be changed to properly use per-CRTC data.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some of the functions are documented inconsistently. Add Returns:
sections where missing and use consistent style to describe the return
value.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Name all references to the pipe number (CRTC index) consistently to make
it easier to distinguish which is a pipe number and which is a pointer
to struct drm_crtc.
While at it also make all references to the pipe number unsigned because
there is no longer any reason why it should ever be negative.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When accessing the array of per-CRTC VBLANK structures we must always
check that the index into the array is valid before dereferencing to
avoid crashing.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[danvet: Squash in my own whitespace ocd fixup in drm_vblank_count.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The drm_send_vblank_event() function treats negative CRTC indices as
meaning that a driver doesn't have proper VBLANK handling. This is the
only place where DRM needs negative CRTC indices, so in order to enable
subsequent cleanup, remove this special case and replace it by the more
obvious check for whether or not VBLANK support was initialized.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than a mix of the the sized uint32_t and signed integer, use an
unsized unsigned int to specify the format count.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
debugfs_remove() gracefully ignores NULL parameters, so the explicit
checks can be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wrap overly long lines to make checkpatch happy. While at it, also add
blank lines after declarations to eliminate additional problems flagged
by checkpatch.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use pr_fmt() to define the "vga_switcheroo: " prefix that is prepended
to all output messages emitted by pr_*() functions. This allows making
existing strings much shorter and eliminates a bunch of warnings from
checkpatch about lines being overly long.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The header comment uses a weird combination of formatting styles. Make
it consistent.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This silences a bunch of checkpatch warnings and makes the code shorter.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wrap overly long lines (offending lines were mostly comments, so trivial
to fix up) and a number of other coding style issues pointed out by the
checkpatch tool.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Define the pr_fmt() macro to causes all messages emitted by pr_*()
functions to be prefixed with "vgaarb: ".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some setups do not register a default VGA device, in which case the VGA
arbiter will still complain about the (non-existent) PCI device being a
non-VGA device.
Fix this by making the error message conditional on a default VGA device
having been set up. Note that the easy route of erroring out early isn't
going to work because otherwise priv->target won't be properly updated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fixes null pointer access incurred when
encoder driver didn't set its own mode_fixup callback.
mode_fixup callback shoudn't be called if the callback
of drm_encoder_helper_funcs is NULL.
Changelog v2:
- change it to else if
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to make sure that no one tries to acquire more locks and
states, and ww mutexes provide debug facilities for that. So use them.
v2: Only call acquire_done when ->atomic_check was successful to avoid
falling over an -EDEADLK (spotted by Maarten).
Cc: Rob Clark <robdclark@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In
commit 6f75cea66c
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 19 18:38:07 2014 +0100
drm/atomic: Only destroy connector states with connection mutex held
I tried to fix races of atomic commits against connector
hot-unplugging. The idea is to ensure lifetimes by holding the
connection_mutex long enough. That works for synchronous commits, but
not for async ones.
For async atomic commit we really need to fix up connector lifetimes
for real. But that's a much bigger task, so just add more duct-tape:
For cleaning up connector states we currently don't need the connector
itself. So NULL it out and remove the locking check. Of course that
check was to protect the entire sequence, but the modeset itself
should be save since currently DP MST hot-removal does a dpms-off. And
that should synchronize with any outstanding async atomic commit.
Or at least that's my hope, this is all a giant mess.
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It really doesn't protect anything which doesn't have other locks
already. It also doesn't seem to be wired up into the driver unload
code fwiw, but that's a different issue.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This is only called in driver load/unload paths, no need to grab any
locks at all. Also, ttm takes care of itself anyway.
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since David Herrmann's mmap vma manager rework we don't need to grab
dev->struct_mutex any more to prevent races when looking up the mmap
offset. Drop it and instead don't forget to use the unref_unlocked
variant (since the drm core still cares).
Aside: I stumbled over the mmap handler which directly does a
dma_mmap_attrs. But totally fails to grab a reference on the
underlying object and hence looks like it happily just leaks the ptes
since there's no guarantee the mmap isn't still around when
gem_free_object is called. Which the kerneldoc of dma_mmap_attrs
explicitly forbids.
v2: Fixup compile fail 0-day spotted.
Cc: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The port is removed synchronously, but the connector delayed.
This causes a use after free which can cause a kernel BUG with
slug_debug=FPZU. This is fixed by freeing the port after the
connector.
This fixes a regression introduced with
6b8eeca65b
"drm/dp/mst: close deadlock in connector destruction."
Cc: stable@vger.kernel.org
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Once pm_runtime_set_active() gets called, the kernel assumes that given
device has already enabled runtime pm and will call pm_runtime_suspend()
without matching pm_runtime_resume(). In case of DRM FIMC IPP driver,
this will result in calling clk_disable() without respective call to
clk_enable(). This patch removes call to pm_runtime_set_active() to
ensure that pm_runtime_suspend/resume calls will match.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
INT_EN cache field was updated only by mixer_enable_vblank.
The patch adds update also by mixer_disable_vblank function.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The driver used incorrect flags to clear interrupt status.
The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
edid returned by drm_get_edid should be freed.
The patch fixes it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The bits for rotation are not used as exclusively. So GSC_IN_ROT_270 can
not be used for swap detection. The definition of it is same with
GSC_IN_ROT_MASK. It is enough to check GSC_IN_ROT_90 bit is set or not to
check whether width / height size swapping is needed.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since David Herrmann's mmap vma manager rework we don't need to grab
dev->struct_mutex any more to prevent races when looking up the mmap
offset. Drop it and instead don't forget to use the unref_unlocked
variant (since the drm core still cares).
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since David Herrmann's mmap vma manager rework we don't need to grab
dev->struct_mutex any more to prevent races when looking up the mmap
offset. Drop it and instead don't forget to use the unref_unlocked
variant (since the drm core still cares).
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Looking up an obj, immediate dropping the acquired reference and then
continuing to use it isn't how this is supposed to work. Fix this by
holding a reference for the entire function.
While at it stop grabbing dev->struct_mutex, it doesn't protect
anything here.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since David Herrmann's mmap vma manager rework we don't need to grab
dev->struct_mutex any more to prevent races when looking up the mmap
offset. Drop it and instead don't forget to use the unref_unlocked
variant (since the drm core still cares).
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since David Herrmann's mmap vma manager rework we don't need to grab
dev->struct_mutex any more to prevent races when looking up the mmap
offset. Drop it and instead don't forget to use the unref_unlocked
variant (since the drm core still cares).
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since David Herrmann's mmap vma manager rework we don't need to grab
dev->struct_mutex any more to prevent races when looking up the mmap
offset. Drop it and instead don't forget to use the unref_unlocked
variant (since the drm core still cares).
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
BUG_ON kills the driver, WARN_ON is much friendlier. And usually nothing
bad happens when the locking is slightly busted.
v2: Fix typos in commit message Thierry spotted.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Pull drm fixes from Daniel Vetter:
"One i915 regression fix and a drm core one since Dave's not around,
both introduced in 4.2 so not cc: stable.
The fix for the warning Ted reported isn't in here yet since he didn't
yet supply a tested-by and I can't repro this one myself (it's in
fixup code that needs firmware doing something i915 wouldn't do)"
* tag 'drm-intel-fixes-2015-08-07' of git://anongit.freedesktop.org/drm-intel:
drm/vblank: Use u32 consistently for vblank counters
drm/i915: Allow parsing of variable size child device entries from VBT
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
In
commit 99264a61df
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 15 19:34:43 2015 +0200
drm/vblank: Fixup and document timestamp update/read barriers
I've switched vblank->count from atomic_t to unsigned long and
accidentally created an integer comparison bug in
drm_vblank_count_and_time since vblanke->count might overflow the u32
local copy and hence the retry loop never succeed.
Fix this by consistently using u32.
Cc: Michel Dänzer <michel@daenzer.net>
Reported-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Even though 'compatability' has a dedicated entry in the Wiktionary,
it's listed as 'Mispelling of compatibility'. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> for the atomic_helper.c
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Pull amdgpu fixes from Alex Deucher:
"Just a few amdgpu fixes to make sure we report the proper firmware
information and number of render buffers to userspace and a typo in a
debugging function"
[ Pulling directly from Alex since Dave Airlie is on vacation - Linus ]
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: set fw_version and feature_version for smu fw loading
drm/amdgpu: add feature version for SDMA ucode
drm/amdgpu: add feature version for RLC and MEC v2
drm/amdgpu: increment queue when iterating on this variable.
drm/amdgpu: fix rb setting for CZ
Pull TDA998x i2c driver fixes from Russell King:
"This fixes the double-checksumming of the AVI infoframe which was
resulting in the checksum always being zero. It went unnoticed as
none of my HDMI devices had a problem with this"
[ Pulling directly from rmk since Dave Airlie is on vacation - Linus ]
* 'drm-tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
drm/i2c: tda998x: fix bad checksum of the HDMI AVI infoframe
VBT version 196 increased the size of common_child_dev_config. The parser
code assumed that the size of this structure would not change.
The modified code now copies the amount needed based on the VBT version,
and emits a debug message if the VBT version is unknown (too new);
since the struct config block won't shrink in newer versions it should
be harmless to copy the maximum known size in such cases, so that's
what we do, but emitting the warning is probably sensible anyway.
In the longer run it might make sense to modify the parser code to
use a version/feature mapping, rather than hardcoding things like this,
but for now the variants are fairly managable.
This fixes a regression introduced in
commit 90e4f1592b
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Mar 25 18:45:58 2015 +0200
drm/i915: Fix the VBT child device parsing for BSW
since we're hitting a DRM_ERROR on older platforms with this.
v2: Stricter size checks
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
[danvet: Fixup format string.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a few core drm patches to be able to merge Maarten's series to
convert DPMS over to atomic.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Legacy fbdev emulation support via DRM is achieved through KMS FB helpers.
Most modesetting drivers enable provide fbdev emulation by default by
selecting KMS FB helpers. A few provide a separate Kconfig option for the
user to enable or disbale fbdev emulation.
Enabling fbdev emulation is finally a distro-level decision. Having a top
level Kconfig option for fbdev emulation helps by providing a uniform way
to enable/disable fbdev emulation for any modesetting driver. It also lets
us remove unnecessary driver specific Kconfig options that causes bloat.
With a top level Kconfig in place, we can stub out the fb helper functions
when not needed without breaking functionality. Having stub functions also
prevents drivers to require wrapping fb helper function calls with #ifdefs.
DRM_FBDEV_EMULATION defaults to y since many drivers enable fbdev
emulation by default and majority of distributions expect the fbdev
interface in the kernel.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If CONFIG_MAGIC_SYSRQ is not set:
drivers/gpu/drm/drm_fb_helper.c:390:13: warning: 'drm_fb_helper_force_kernel_mode' defined but not used [-Wunused-function]
static bool drm_fb_helper_force_kernel_mode(void)
^
Move drm_fb_helper_force_kernel_mode() inside the existing #ifdef to fix
this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As of commit 5ea1f752ae ("drm: add
drm_fb_helper_restore_fbdev_mode_unlocked()"),
drm_fb_helper_restore_fbdev_mode() is no longer public, and drivers
should call drm_fb_helper_restore_fbdev_mode_unlocked() from their
->lastclose callbacks instead.
Update the documentation to reflect this, and absorb the one liner
drm_fb_helper_restore_fbdev_mode() into its single caller.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag and there
is no need to do that again from its callers. Drop it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Don't touch remove_conflicting_framebuffers
v2:
- add missing header for virtgpu_fb.c
Cc: David Airlie <airlied@linux.ie>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Don't touch remove_conflicting_framebuffers
v2:
- remove unused variable device in bochsfb_create
Cc: David Airlie <airlied@linux.ie>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Don't touch remove_conflicting_framebuffers
v2:
- remove unused variable pdev in nouveau_fbcon_create
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Don't touch remove_conflicting_framebuffers
v2:
- No changes
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Don't touch remove_conflicting_framebuffers
v2:
- Fix build break because of missing include of drm_fb_helper in
radeon_drv.c
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Don't touch remove_conflicting_framebuffers
v2:
- remove unused goto label 'out'
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v3:
- Update error handling for new drm_fb_helper funcs. Check using IS_ERR()
instead of checking for NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
v2:
- No changes
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With
commit 7a3f3d6667
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 9 23:44:28 2015 +0200
drm: Check locking in drm_for_each_connector
we started checking the locking in drm_for_each_connector but somehow
I totally missed drm_mode_config_reset. There's no problem there since
this function should only be called in single-threaded contexts
(driver load or resume), so just wrap the loop with the right lock.
v2: Drink coffee and all that ...
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The last user is gone, no need for trylocking any more in this legacy
helper.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since the panic handling is gone this is only used for force-restoring
the fbdev/fbcon from sysrq, and that's done with a work item. No need
any more to do trylocks, we can just do normal locking.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Trying to do anything with kms drivers when oopsing has become a
failing proposition. But since we can end up in the fbdev code simply
due to the console unblanking that's done unconditionally just
removing our panic handler isn't enough. We need to block all fbdev
callbacks when oopsing.
There was already one in the blank handler, but it failed silently.
That makes it impossible for drivers (like i915) who subclass these
functions to figure this out.
Instead consistently return -EBUSY so that everyone knows that we
really don't want to be bothered right now. This also allows us to
remove a pile of FIXMEs from the i915 fbdev code (since due to the
failure code they now won't attempt to grab dangerous locks any more).
Cc: Dave Airlie <airlied@gmail.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v2:
- remove unused variable device in udlfb_create
Cc: David Airlie <airlied@linux.ie>
Cc: Haixia Shi <hshi@chromium.org>
Cc: "Stéphane Marchesin" <marcheu@chromium.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
Cc: David Airlie <airlied@linux.ie>
Cc: Frediano Ziglio <fziglio@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v2:
- removed unused variable 'device' in psbfb_create
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v2:
- Remove unnecessary dealloc cmap in error handling path
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Stephane Viau <sviau@codeaurora.org>
Cc: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
v2:
- Fix up error handling path in tegra_fbdev_probe
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Terje Bergström" <tbergstrom@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
Cleaned up the error handling in astfb_create a bit.
v2:
- removed unused variable 'device' in astfb_create
Cc: David Airlie <airlied@linux.ie>
Cc: "Y.C. Chen" <yc_chen@aspeedtech.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the newly created wrapper drm_fb_helper functions instead of calling
core fbdev functions directly. They also simplify the fb_info creation.
This is an effort to create a top level drm fbdev emulation option.
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some drm drivers call fb_set_suspend. Create a drm_fb_helper function
that wraps around these calls.
This is part of an effort to prevent drm drivers from calling fbdev
functions directly, in order to make fbdev emulation a top level drm
option.
v3:
- Fixed kerneldoc errors
v2:
- Added kerneldocs
- Added a check for non-NULL fb_helper before proceeding. This will
make the helpers work when we have a module param for fbdev emulation
- Follow the drm way of aligning of arguments in func definitions
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm drivers that emulate fbdev populate their fb_fillrect, fb_copyarea
and fb_imageblit fb_ops with the help of cfb_* or sys_* fbdev core
helper functions.
Create drm_fb_helper functions that wrap around these calls.
This is part of an effort to prevent drm drivers from calling fbdev
functions directly, in order to make fbdev emulation a top level drm
option.
v3:
- Fixed kerneldoc errors
v2:
- Added kerneldocs
- Follow the drm way of aligning of arguments in func definitions
- Remove unnecessary checks for non NULL fb_info
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some drm drivers populate their fb_ops with fb_sys_read/write fb sysfs
ops.
Create a drm_fb_helper function that wraps around these calls.
This is part of an effort to prevent drm drivers from calling fbdev
functions directly, in order to make fbdev emulation a top level drm
option.
v3:
- Fix kerneldoc errors
v2:
- Added kerneldocs
- Follow the drm way of aligning of arguments in func definitions
- Remove unnecessary checks for non NULL fb_info
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some drm drivers call unlink_framebuffer. Create a drm_fb_helper function
that wraps around these calls.
This is part of an effort to prevent drm drivers from calling fbdev
functions directly, in order to make fbdev emulation a top level drm
option.
v2:
- Added kerneldocs
- Added a check for non-NULL fb_helper before proceeding. This will
make the helpers work when we have a module param for fbdev emulation
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every drm driver calls framebuffer_alloc, fb_alloc_cmap,
unregister_framebuffer, fb_dealloc_cmap and framebuffer_release in
order to emulate fbdev support.
Create drm_fb_helper functions that perform the above operations.
This is part of an effort to prevent drm drivers from calling fbdev
functions directly. It also removes repetitive code from drivers.
There are some drivers that call alloc_apertures after framebuffer_alloc
and some that don't. Make the helper always call alloc_apertures. This
would make certain drivers allocate memory for apertures but not use
them. Since it's a small amount of memory, it shouldn't be an issue.
v2:
- Added kerneldocs
- Added a check for non-NULL fb_helper before proceeding. This will
make the helpers work when we have a module param for fbdev emulation
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Maarten didn't fully test his patches on all drm drivers and
apparently missed a few places when grepping.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The fw_version and feature_verion should be set correctly when the
firmwares are loaded by SMU on Tonga/Carrzio/Iceland
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Expose feature version to user space for RLC/MEC/MEC2 ucode as well
v2: fix coding style
Signed-off-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
gfx_v7_0_print_status contains a for loop on variable queue which does
not update this variable between each iteration. This is bug is
reported by clang while building allmodconfig LLVMLinux on x86_64:
drivers/gpu/drm/amd/amdgpu/gfx_v7_0.c:5126:19: error: variable
'queue' used in loop condition not modified in loop body
[-Werror,-Wloop-analysis]
for (queue = 0; queue < 8; i++) {
^~~~~
Fix this by incrementing variable queue instead of i in this loop.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Always set num_rbs to 2 for CZ. The 1 RB parts are often harvest
configs. The will get sorted out in mesa when we program
PA_SC_RASTER_CONFIG[_1].
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by Intel's kbuild robot.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
When the size of dma_addr_t was 32 bits, the compiler warned
about the size of the 32 bit shift being larger than the size
of the data type.
Reported by Intel's kbuild robot.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
We're giving up all attempts to keep cpu- and device byte ordering separate.
This silences sparse when compiled using
make C=2 CF="-D__CHECK_ENDIAN__"
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The preferred mode typically didn't end up first, since the function
drm_mode_connector_list_update() reordered the modes.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
With screen targets the old legacy display system fbdev doesn't work
satisfactory anymore. At best the resolution is severely restricted.
Therefore implement fbdev on top of the kms system. With this change, fbdev
will be using whatever KMS backend is chosen.
There are helpers available for this, so in the future we'd probably want
to implement the helper callbacks instead of calling into our KMS
implementation directly.
v2: Make sure we take the mode_config mutex around modesetting,
Also clear the initial framebuffer using vzalloc instead of vmalloc.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
The kernel interface is needed for fbdev, and needs to be free from
a file_priv member. To accomplish this, remove the fb surface mutex
and list which isn't used anymore, anyway.
Finally, make the pin() and unpin() pin the framebuffer for all display
system backends, so that fbdev can pin its framebuffer before mapping it.
v2: Address review comments:
- Fix vmw_framebuffer_unpin() to handle also the surface framebuffer case.
- Fix vmw_kms_new_framebuffer() to actually use the only_2d parameter.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
If the command buffer pool is out of space, the code waits until space is
available. However since the condition code tries to allocate a range manager
node while !TASK_RUNNING we get a kernel warning.
Avoid this by pre-allocating the mm node. This will also probably be more
efficient.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Also implements the missing readback function and
fixes page flip in case of no event.
v2:
- Adapt to the work done for screen targets for 2d, in particular
Handle proxy surface updates.
- Remove execbuf quirks since we now use fifo reserve / commit.
- Revert the initial placement of vmw dma buffers.
v3: Address review comments.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
This makes it possible to use the same function for surface dirty and
present. Also fixes page flip without events.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
We need to make the dirty- and readback functions callable without a struct
drm_file pointer. We also need to unify the handling of dirty- and readback
cliprects that are now implemented in various places across the kms system,
som add helpers to facilitate this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
This patch address the following underlying issues with SurfaceDMA
* SurfaceDMA command does not work in a 2D VM, but we can wrap a
proxy surface around the same DMA buffer and use the SurfaceCopy
command which does work in a 2D VM.
* Wrapping a DMA buffer with a proxy surface also gives us an
added optimization path for the case when the DMA buf
dimensions match the mode. In this case, the DMA buf can
be pinned as the display surface, saving an extra copy.
This only works in a 2D VM because we won't be doing any
rendering operations directly to the display surface.
v2
* Moved is_dmabuf_proxy field to vmw_framebuffer_surface
* Undone coding style changes
* Addressed other issues from review
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Add support for the screen target device interface.
Add a getparam parameter and bump minor to signal availability.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
For certain surface copies, we don't have a user space handle for
the destination surface. In such cases, we are going to trust that
our caller is giving us the right surface ID.
To do this case, we created a quirk flag that may be useful
in the future for handling other cases.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Refactored vmw_gb_surface_define_ioctl() and made the surface
definition part a separate function. This way other parts of vmwgfx
can use it to allocate kernel-visible GB surfaces.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
For screen targets it appears we need to pin surfaces while they are bound
as screen targets, so add a small interface to do that.
v2: Always increase pin_count on pin.
v3: Add missing reservation sem.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Fix a circular locking dependency between
struct vmw_overlay::mutex and
struct vmw_private::reservation_sem
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Add command buffer support.
Currently we don't implement preemption or fancy error handling.
Tested with a couple of mesa-demos, compiz/unity and viewperf maya-03.
v2:
- Synchronize with pending work at command buffer manager takedown.
- Add an interface to flush the current command buffer for latency-critical
command batches and apply it to framebuffer dirtying.
v3:
- Minor fixes of definitions and typos to address reviews.
- Removed new or moved branch predictor hints.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
This commit reworks device initialization so that we always enable the
FIFO at driver load, deferring SVGA enable until either first modeset
or fbdev enable.
This should always leave the fifo properly enabled for render- and
control nodes.
In addition,
*) We disable the use of VRAM when SVGA is not enabled.
*) We simplify PM support so that we only throw out resources on hibernate,
not on suspend, since the device keeps its state on suspend.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
A regression introduced when the master ttm lock was split into two.
Reported-and-tested-by: Brian Paul <brianp@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
The commit 8c7a075da9
"drm/i2c: tda998x: use drm_hdmi_avi_infoframe_from_display_mode()"
also uses hdmi_avi_infoframe_pack() to create the AVI infoframe.
This function sets the checksum of the frame and this breaks
the second calculation of the checksum done in tda998x_write_if().
Fixes: 8c7a075da9 ("drm/i2c: tda998x: use drm_hdmi_avi_infoframe_from_display_mode()")
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Looks like
commit eddfcbcdc2
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon Jun 15 12:33:53 2015 +0200
drm/i915: Update less state during modeset.
introduced the unconditional calling of disable_shared_dpll, but didn't
fix up pre-gen5 to avoid the BUG_ON at the top of the function.
So change the BUG_ON into a gen check (alternately we could move the
BUG_ON until later, since we shouldn't have a pll struct here either,
but this seems clearer to read).
This fixes a crash on load on my x200s platform.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains the changes to remove the byte
swapping logic introduced with old dmc firmware.
While debugging PC10 entry issue for skylake found
with latest dmc firmware version 1.18 without byte
swapping dmc is working fine and able to enter PC10.
Note that apparently this was changed with dmc version 1.0 and earlier
ones indeed are byteswapped like this ...
v1: Initial version.
v2: Corrected firmware size during memcpy(). (Suggested by Sunil)
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
[danvet: Add note that this only holds for released dmc firmware.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BPP bits defined in VBT should be used only on panels whose
edid version is 1.3 or older. EDID version 1.4 introduced offsets
where bpp is defined and read into display_info, hence bpp from
VBT will be used only when bpc in display_info is zero.
v2: use display_info.bpc for deciding when to use vbt_bpp (Jani)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was told that the "repurposed D1 definition" is still valid for SKL.
It is BDW that is special due to its hotplug bug, so let's
special-case BDW instead of HSW.
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to the ->enable vfunc in patch "drm/i915: Extract a
intel_power_well_enable() function".
v2 (from Paulo):
- Same s/i915_/intel_/ bikeshed as the previous patch.
- Update the commit hash.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need a bit book keeping around power wells' ops->enable(), namely a
nice debug message and updating hw_enabled. Let's introduce a
intel_power_well_enable() function to make sure all the callers do the
same things.
v2 (from Paulo):
- s/i915_power_well_enable/intel_power_well_enable/ since everything
else on this file uses intel_ instead of i915_.
- Fix typo in commit message.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this simple git diff command one can see that skl_init_workarounds()
got two copies of WaBarrierPerformanceFixDisable:skl:
git diff -U21 ca6e4405779e^1 ca6e440577 drivers/gpu/drm/i915/intel_ringbuffer.c
This happened when the backmerge of drm-intel-fixes-2015-07-15
Merged the same fix on both sides. Same fix but not identical enough for
git: with a different surrounding context; hence the code duplication.
This commit merely reverts the output of the git command above
= the duplication introduced in the backmerge.
(This duplication was found while running git sanity checks on a
_linearized_ i915 forklift for ChromeOS.)
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since active function on VLV immediately activate PSR let's give more
time for idleness. Different from core platforms where we have idle_frames
count.
Also kms_psr_sink_crc now is automated and always get this:
[drm:intel_enable_pipe] enabling pipe A
[drm:intel_edp_backlight_on]
[drm:intel_panel_enable_backlight] pipe
[drm:intel_panel_enable_backlight] pipe A
[drm:intel_panel_actually_set_backlight] set backlight PWM = 7812
PSR gets enabled somewhere here after backlight.
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x0
[drm:vlv_pipe_set_fifo_size] Pipe A FIFO split 511 / 511 / 511
[drm:vlv_update_wm] Setting FIFO watermarks - A: plane=391, cursor=63, sp
PSR gets flushed around here by intel_atomic_commit
[drm:vlv_pipe_set_fifo_size] Pipe A FIFO split 511 / 511 / 511
[drm:vlv_update_wm] Setting FIFO watermarks - A: plane=391, cursor=63, sp
[drm:intel_set_memory_cxsr] memory self-refresh is enabled
[drm:intel_connector_check_state] [CONNECTOR:39:eDP-1]
[drm:check_encoder_state] [ENCODER:30:DAC-30]
[drm:check_encoder_state] [ENCODER:31:TMDS-31]
[drm:check_encoder_state] [ENCODER:36:TMDS-36]
[drm:check_encoder_state] [ENCODER:38:TMDS-38]
[drm:check_crtc_state] [CRTC:21]
[drm:check_crtc_state] [CRTC:26]
[drm:intel_psr_activate [i915]] *ERROR* PSR Active
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x
[drm:intel_set_cpu_fifo_underrun_reporting [i915]] *ERROR* pipe A underrun
[drm:intel_cpu_fifo_underrun_irq_handler [i915]] *ERROR* CPU pipe A FIFO
Underrun.
It is true that in a product we won't keep disabling and enabling planes so
frequently, but for safeness let's stay conservative.
It is also true that 500ms is an etternity. But PSR is anyway a power saving
feature for idle scenario. So if it is idle feature stays on and 500ms to get
it reanabled is not that insane.
v2: Rebase over intel_psr.c and fix typo.
v3: Revival: Manual tests indicated that this is needed. With a short delay
there is a huge risk of getting blank screens when planes are being enabled.
v4: Revival 2 with reasonable delay. 1/2 sec instead of 5. VBT is 10 sec but
actually time for link training what we aren't doing, but with only 100 sec
in some cases kms_psr_sink_crc manual was showing blank screen,
so let's use this for now. Also changed comment by a FIXME.
v5: Rebase after a long time, remove FIXME and update comment above.
v6: msecs_to_jiffies is already on delay. remove duplication.
v7: use msecs_to_jiffies on schedule_delayed_work call.
Reviewed-by: Durgadoss R <durgadoss.r@intel.com> (v4)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-By: Intel Graphics QA PRTS (Patch Regression Test System Contact: shuang.he@intel.com)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just a preparation patch to make clear what operation we
are performing. There is no functional change on the sink crc
logic.
hsw_disable_ips has been moved a bit further in the start function
to avoid disabling ips when sink crc is not going to be started.
and to avoid goto on this function.
v2: explain why hsw_disable_ips() call place has changed.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First, an introduction. We currently have two types of GTT mmaps: the
"normal" old mmap, and the WC mmap. For frontbuffer-related features
that have automatic hardware tracking, only the non-WC mmap writes are
detected by the hardware. Since inside the Kernel both are treated as
ORIGIN_GTT, any features ignoring ORIGIN_GTT because of the hardware
tracking are destined to fail.
One of the special rules defined for the WC mmaps is that the user
should call the dirtyfb IOCTL after he is done using the pointers, so
that results in an intel_fb_obj_flush() call. The problem is that the
dirtyfb is passing ORIGIN_GTT, so it is being ignored by FBC - even
though the hardware tracking is not detecing the WC mmap operations.
So in order to fix that without having to give up the automatic
hardware tracking for GTT mmaps we transform the flush operation from
dirtyfb into a special operation: ORIGIN_DIRTYFB.
This commit fixes all the kms_frontbuffer_tracking subtests that
contain "fbc" and "mmap-wc" in their names and are currently failing
(for a total of 16 subtests).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the appropriate call.
I know there's a discussion about whether we need this call here at
all, but removing the call means we'll only update FBC after we get
the page flip IRQ. So the user may only see the new frame a little
after it should. Let's wait just a little bit more before removing
this call since we can rely in the HW tracking for accurate flips.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because intel_unpin_work_fn() already calls
intel_frontbuffer_flip_complete() which will call intel_fbc_flush()
which will call intel_fbc_update() when needed.
We couldn't fix this previously due to the fact that FBC was not
properly behaving as intended on frontbuffer flushes, but now that
this is fixed, we can remove the additional call.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to the way busy_bits was handled, we were not doing any flushes if
we didn't previously get an invalidate. Since it's possible to get
flushes without an invalidate first, remove the busy_bits early
return.
So now that we don't have the busy_bits guard anymore we'll need the
origin check for the GTT tracking (we were not doing anything on GTT
flushes due to the GTT check at invalidate()).
As a last detail, since we can get multiple consecutive flushes,
disable FBC before updating it, otherwise intel_fbc_update() will just
keep FBC enabled instead of restarting it.
Notice that this does not fix any of the current IGT tests due to the
fact that we still have a few intel_fbc() calls at points where we
also have the frontbuffer tracking calls: we didn't fully convert to
frontbuffer tracking yet. Once we remove those calls and start relying
only on the frontbuffer tracking infrastructure we'll need this patch.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've had a few issues with atomic where subtle bugs in the encoder
picking logic lead to accidental self-stealing of the encoder,
resulting in a NULL connector_state->crtc in update_connector_routing
and subsequent.
Linus applied some duct-tape for an mst regression in
commit 27667f4744
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Wed Jul 29 22:18:16 2015 -0700
i915: temporary fix for DP MST docking station NULL pointer dereference
But that was incomplete (the code will still oops when debuggin is
enabled) and mangled the state even further. So instead WARN and bail
out as the more future-proof option.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Apparently been in there since forever and fairly easy to hit when
hotplugging really fast. I can do that since my mst hub has a manual
button to flick the hpd line for reprobing. The resulting WARNING spam
isn't pretty.
Cc: Dave Airlie <airlied@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In
commit 8c7b5ccb72
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Tue Apr 21 17:13:19 2015 +0300
drm/i915: Use atomic helpers for computing changed flags
we've switched over to the atomic version to compute the
crtc->encoder->connector routing from the i915 variant. That one
relies upon the ->best_encoder callback, but the i915-private version
relied upon intel_find_encoder. Which didn't matter except for dp mst,
where the encoder depends upon the selected crtc.
Fix this functional bug by implemented a correct atomic-state based
encoder selector for dp mst.
Note that we can't get rid of the legacy best_encoder callback since
the fbdev emulation uses that still. That means it's incorrect there
still, but that's been the case ever since i915 dp mst support was
merged so not a regression. Best to fix that by converting fbdev over
to atomic too.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With legacy helpers all the routing was already set up when calling
best_encoder and so could be inspected. But with atomic it's staged,
hence we need a new atomic compliant callback for drivers which need
to inspect the requested state and can't just decided the best encoder
statically.
This is needed to fix up i915 dp mst where we need to pick the right
encoder depending upon the requested CRTC for the connector.
v2: Don't forget to amend the kerneldoc
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Better fit STI hardware structure.
Planes are no more responsible of updating mixer information such
as z-order and status. It is now up to the CRTC atomic flush to
do it. Plane actions (enable or disable) are performed atomically.
Disabling of a plane is synchronize with the vsync event.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
replace all "sti_drm_" occurences by "sti_"
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Purpose is to simplify the STI driver:
- remove layer structure
- consider video subdev as part of the compositor (like mixer subdev)
- remove useless STI_VID0 and STI_VID1 enum
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Apply the plane depth when the plane is updated.
If the depth is different from the previous plane update,
the register controlling the plane depth is cleaned and updated
with the new depth.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Fix misunderstanding in how use component framework.
drm_platform_init() is now call only when all the
sub-components are register themselves instead of the
previous broken two stages mechanism.
Update bindings documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Ted Ts'o reports that his Lenovo T540p ThinkPad crashes at boot if
attached to the docking station. This is a regression that he was able
to bisect to commit 8c7b5ccb72: "drm/i915: Use atomic helpers for
computing changed flags:"
The reason seems to be the new call to drm_atomic_helper_check_modeset()
added to intel_modeset_compute_config(), which in turn calls
update_connector_routing(), and somehow ends up picking a NULL crtc for
the connector state, causing the subsequent drm_crtc_index() to OOPS.
Daniel Vetter says that the fundamental issue seems to be confusion in
the encoder selection, and this isn't the right fix, but while he chases
down the proper fix, this at least avoids the NULL pointer dereference
and makes Ted's docking station work again.
Reported-bisected-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Mani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm intel fixes from Daniel Vetter:
"I delayed my -fixes pull a bit hoping that I could include a fix for
the dp mst stuff but looks a bit more nasty than that. So just 3
other regression fixes, one 4.2 other two cc: stable"
* tag 'drm-intel-fixes-2015-07-31' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/i915: Mark PIN_USER binding as GLOBAL_BIND without the aliasing ppgtt
drm/i915: Replace WARN inside I915_READ64_2x32 with retry loop
The old style of memory interleaving swizzled upto the end of the
first even bank of memory, and then used the remainder as unswizzled on
the unpaired bank - i.e. swizzling is not constant for all memory. This
causes problems when we try to migrate memory and so the kernel prevents
migration at all when we detect L-shaped inconsistent swizzling.
However, this issue also extends to userspace who try to manually detile
into memory as the swizzling for an individual page is unknown (it
depends on its physical address only known to the kernel), userspace
cannot correctly swizzle.
Note that this is a new attempt for the previously merged one,
reverted in
commit d82c0ba6e3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jul 14 12:29:27 2015 +0200
Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations"
This is cc: stable since we need it to fix up troubles with wc cpu
mmaps that userspace recently started to use widely.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91105
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[danvet: Add note about previous (failed attempt).]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the device does not support the aliasing ppgtt, we must translate
user bind requests (PIN_USER) from LOCAL_BIND to a GLOBAL_BIND. However,
since this is device specific we cannot do this conveniently in the
upper layers and so must manage the vma->bound flags in the backend.
Partial revert of commit 75d04a3773 [4.2-rc1]
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Tue Apr 28 17:56:17 2015 +0300
drm/i915/gtt: Allocate va range only if vma is not bound
Note this was spotted by Daniel originally, but we dropped the ball in
getting the fix in before the bug going wild. Sorry all.
Reported-by: Vincent Legoll vincent.legoll@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91133
References: https://bugs.freedesktop.org/show_bug.cgi?id=90224
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A logical AND operation was used during mask and shift, instead of a
bitwise AND operation. This patch fixes this bug by changing the
operation to bitwise AND.
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The wrong define was used to check if the hqd is still active
v2: Don't use SHIFT as the MASK is already shifted
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Fix for nasty crash on mdp4 in disable path, fix for dma-buf export,
smb leak on mdp5 which could result in intermittent modeset fails, and
don't let interrupted system call disturb atomic commit once we are
past the point of no return.
* 'msm-fixes-4.2' of git://people.freedesktop.org/~robclark/linux:
drm/msm/mdp5: release SMB (shared memory blocks) in various cases
drm/msm: change to uninterruptible wait in atomic commit
drm/msm: mdp4: Fix drm_framebuffer dereference crash
drm/msm: fix msm_gem_prime_get_sg_table()
Release all blocks after the pipe is disabled, even when vsync
didn't happen in some error cases. Allow requesting SMB multiple
times before configuring to hardware, by releasing blocks not
programmed to hardware yet for shrinking case.
This fixes a potential leak of shared memory pool blocks.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The atomic commit cannot easily undo and return an error once the
state is swapped. Change to uninterruptible wait, and ignore the
timeout error.
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp4_get_frame_format() can dereference a drm_framebuffer when it's NULL.
Call it in mdp4_plane_mode_set only when we know fb is non-NULL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to return a new sgt, since the caller takes ownership of it.
Reported-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
hdp flush is not needed for IBs that dispatched from kernel inside
because there is no video memory host access
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
compute ring didn't use const engine byfar, so ignore CE things in
compute routine
Signed-off-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
We recently changed the drm_amdgpu_info_device struct so now there is
a 4 byte hole at the end. We need to initialize it so we don't disclose
secret information from the stack.
Fixes: fa92754e9c ('drm/amdgpu: add VCE harvesting instance query')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we fail during device init, record what state each
block is in so that we can tear down clearly.
Fixes various problems on device init failure.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes a broken hsync start value uncovered by:
abc0b1447d
(drm: Perform basic sanity checks on probed modes)
The driver handled the bad hsync start elsewhere, but
the above commit prevented it from getting added.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91401
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
1. Always assign audio function pointers even if the display does
not support audio. We need to properly disable the audio stream
when when using a non-audio capable monitor. Fixes purple line
on some hdmi monitors.
2. Check if a pin is in use by another encoder before disabling
it.
v2: make sure we've fetched the edid before checking audio and
look up the encoder before calling audio_detect since
connector->encoder may not be assigned yet. Separate
pin and afmt. They are allocated at different times and
have no dependency on eachother.
v3: fix connector fetching in encoder functions
v4: fix missed dig->pin check in dce6_afmt_write_latency_fields
bugs:
https://bugzilla.kernel.org/show_bug.cgi?id=93701https://bugzilla.redhat.com/show_bug.cgi?id=1236337https://bugs.freedesktop.org/show_bug.cgi?id=91041
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
As we may like to use a bisection search on the tables in future, we
need them to be ordered. For convenience we expect the compiled tables
to be order and check on initialisation. However, the validator used the
wrong iterators failed to spot the misordered MI tables and instead
walked off into the unknown (as spotted by kasan).
Signed-off-by: Hanno Boeck <hanno@hboeck.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Again hand-assemble patch ...]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In the future, we may want to speed up command/register searching using
a bisection and so we require them to be in ascending order respectively
by command value or register address. However, this was not true for one
pair in the MI table; make it so.
Signed-off-by: Hanno Boeck <hanno@hboeck.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Hand-assemble patch from raw patch from Hanno and commit message from Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
If we got to the point where we are trying to stop sink CRC
the main output of this function was already gotten properly,
so don't return the error and let userspace use the crc data.
Let's replace the errnos returns with some log messages.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Right now if we face any kind of error sink crc calculation
stays enabled.
So, let's give a shot and try to stop it anyway if it got enabled.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rafael Antognolli <rafael.antognolli@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we may conceivably encounter situations where the upper part of the
64bit register changes between reads, for example when a timestamp
counter overflows, change the WARN into a retry loop.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we shrink our working sets, we want to avoid stealing pages from
objects that likely to be reused in the near future. We first look at
inactive objects before processing active objects - but what about a
recently active object that is about to be used again. That object's
position in the bound_list is ordered by the time of binding, not the
time of last use, so the most recently used inactive object could well
be at the head of the shrink list. To compensate, give the object a bump
to MRU when it becomes inactive (thus transitioning to the end of the
first pass in shrink lists). Conversely, bumping on inactive makes
bumping on active useless, since when we do have to reap from the active
working set, everything is going to become inactive very quickly and the
order pretty much random - just hope for the best at that point, as once
we start stalling on active objects, we can hope that the rebinding
neatly orders vital objects.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Resolve merge conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the leftovers, yay!
AGP for i915 kms died long ago with
commit 3bb6ce6686
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:14:16 2013 +0100
drm/i915: Kill legeacy AGP for gen3 kms
and with ums now gone to there's really no users any more.
Note that device_is_agp is only called when DRIVER_USE_AGP is set and
since we've unconditionally cleared that since a while there are
really no users left for i915_driver_device_is_agp.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Add Maxwell to the switch statement that sets node->memtype, otherwise
all tiling information is ignored for buffers in system memory.
While we are at it, make that switch statement explicitly complain the
next time we meet a non-handled card family.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Userspace has started doing this, which upsets the display class hw
error checking in various unpleasant ways.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is required for DPMS to work correctly, during a modeset
the DPMS property should be turned off, unless the state is
crtc is made active in which case it should be set to DPMS on.
Changes since v1:
- Set DPMS to off when a connector is removed from a crtc too.
- Update the legacy dpms property too.
- Add an exception for the legacy dpms paths, it updates its own state.
Changes since v2:
- Do not preserve dpms property.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required to properly handle failing dpms calls.
When making a wait in i915 interruptible, I've noticed
that the dpms sequence could fail with -ERESTARTSYS because
it was waiting interruptibly for flips. So from now on
allow drivers to fail in their connector dpms callback.
Encoder and crtc dpms callbacks are unaffected.
Changes since v1:
- Update kerneldoc for the drm helper functions.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[danvet: Resolve conflicts due to different merge order.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In intel it's useful to keep track of some state changes with old
crtc state vs new state, for example to disable initial planes or
when a modeset's prevented during fastboot.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
[danvet: squash in fixup for exynos provided by Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace the deprecated atomic_{set,clear}_mask() usage with the now
ubiquous atomic_{or,andnot}() functions.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Only 58 words get written to the ring, not 59. Also, normalize the accel
init wrt nvc0 and nv04 fbcon impls by firing the ring at accel init time
rather than waiting until "later".
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The RING_SPACE macro accounts how much space is used up so it's
important to ask it for the right amount. Incorrect accounting of this
can cause page faults down the line as writes are attempted outside of
the ring.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
More analysis shows that this is identical to 0x79 except that it loads
the frequency indirectly from elsewhere in the VBIOS.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91025
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Opcode 0x5a is a register write for data looked up from another part of
the VBIOS image. 0x59 is a more complex opcode, but we may as well
recognize it. These occur on a single known instance of Riva TNT2
hardware.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91025
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The return type of exec_lookup() is struct nvkm_output *, so it should
return NULL rather than 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There is always the possiblity that the ppm->context pointer would get
partially updated and accidentally would equal ctx. This would allow two
contexts to co-exist, which is not acceptable. Moving the test to the
critical section takes care of this problem.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This fixes a crash when multiple PM engine contexts are created.
Signed-off-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Reviewed-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
After submitting a GO_IDLE bundle, one must wait for GR to effectively
be idle before submitting the next bundle. Failure to do so may result
in undefined behavior in some rare cases.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Kary Jin <karyj@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When emitting the ICMD bundle, wait on the bottom half (bit 3 of the
GR_STATUS register) instead of upper half (bit 2) to make sure methods
are effectively emitted.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Kicking channels is part of their deactivation process. Maxwell chips
are particularly sensitive to this, and can start fetching the previous
pushbuffer of a recycled channel if this is not done.
While we are at it, improve the channel preemption code to only wait for
bit 20 of 0x002634 to turn to 0, as it is the bit indicating a
preempt is pending.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Increase clock timeout for SYS, FPB and GPC in order to avoid operation
failure at high gpcclk rate.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The lack of IOMMU API support can make nouveau_platform_probe_iommu()
fail to compile because struct iommu_ops is then empty. Fix this by
skipping IOMMU probe in that case - lack of IOMMU on platform devices
is sub-optimal, but is not an error.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The memory allocated for a nouveau_cli object in nouveau_cli_create() is
never freed. Free the memory in nouveau_cli_destroy() to plug this leak.
kmemleak recorded this after running a couple of nouveau test programs.
Note that kmemleak points at drm_open_helper() because for some reason
it thinks that skipping the first two stack frames is a good idea.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Chris rightfully suggested that documenting fences without documenting
the BO tiling tracking doesn't make much sense, so fix that.
The important bit to stress here (since it lead to some confusion) is
the GEM doesn't really care about tiling. Except for a few select cases
where the kernel needs to manage something that userspace can't take
care of: Namely the limited number of fences and fixing up swizzling,
although we still fail at the later.
v2: Move the low-level tiling/swizzling functions and kerneldoc to
i915_gem_fence.c and leave only the userspace interface here.
Suggested by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It fits more with the low-level fence code, and this move leaves only
the userspace tiling ioctl handling in i915_gem_tiling.c.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
v2: Clarify that this is about fence _registers_. Also clarify that
the fence code revokes cpu ptes and not gtt ptes. Both suggested by
Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
