Johannes Berg says:
====================
brcmfmac
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
mac80211: Add support to trigger sta disconnect on hardware restart
mac80211: fix potential double free on mesh join
mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
rtw89: 8852c: process logic efuse map
rtw89: 8852c: process efuse of phycap
rtw89: support DAV efuse reading operation
rtw89: 8852c: add chip::dle_mem
rtw89: add page_regs to handle v1 chips
rtw89: add chip_info::{h2c,c2h}_reg to support more chips
rtw89: add hci_func_en_addr to support variant generation
rtw89: add power_{on/off}_func
rtw89: read chip version depends on chip ID
rtw89: pci: use a struct to describe all registers address related to DMA channel
rtw89: pci: add V1 of PCI channel address
rtw89: pci: add struct rtw89_pci_info
rtw89: 8852c: add 8852c empty files
MAINTAINERS: add devicetree bindings entry for mt76
...
====================
Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently in case of target hardware restart, we just reconfig and
re-enable the security keys and enable the network queues to start
data traffic back from where it was interrupted.
Many ath10k wifi chipsets have sequence numbers for the data
packets assigned by firmware and the mac sequence number will
restart from zero after target hardware restart leading to mismatch
in the sequence number expected by the remote peer vs the sequence
number of the frame sent by the target firmware.
This mismatch in sequence number will cause out-of-order packets
on the remote peer and all the frames sent by the device are dropped
until we reach the sequence number which was sent before we restarted
the target hardware
In order to fix this, we trigger a sta disconnect, in case of target
hw restart. After this there will be a fresh connection and thereby
avoiding the dropping of frames by remote peer.
The right fix would be to pull the entire data path into the host
which is not feasible or would need lots of complex changes and
will still be inefficient.
Tested on ath10k using WCN3990, QCA6174
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we get anti-clogging token required (added by the commit
mentioned below), or the other status codes added by the later
commit 4e56cde15f ("mac80211: Handle special status codes in
SAE commit") we currently just pretend (towards the internal
state machine of authentication) that we didn't receive anything.
This has the undesirable consequence of retransmitting the prior
frame, which is not expected, because the timer is still armed.
If we just disarm the timer at that point, it would result in
the undesirable side effect of being in this state indefinitely
if userspace crashes, or so.
So to fix this, reset the timer and set a new auth_data->waiting
in order to have no more retransmissions, but to have the data
destroyed when the timer actually fires, which will only happen
if userspace didn't continue (i.e. crashed or abandoned it.)
Fixes: a4055e74a2 ("mac80211: Don't destroy auth data in case of anti-clogging")
Reported-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20220224103932.75964e1d7932.Ia487f91556f29daae734bf61f8181404642e1eec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the possible failure of the alloc, the ifmgd->assoc_req_ies might be
NULL pointer returned from kmemdup().
Therefore it might be better to free the skb and return error in order
to fail the association, like ieee80211_assoc_success().
Also, the caller, ieee80211_do_assoc(), needs to deal with the return
value from ieee80211_send_assoc().
Fixes: 4d9ec73d2b ("cfg80211: Report Association Request frame IEs in association events")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220105081559.2387083-1-jiasheng@iscas.ac.cn
[fix some paths to be errors, not success]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clang static analysis reports this warnings
mlme.c:5332:7: warning: Branch condition evaluates to a
garbage value
have_higher_than_11mbit)
^~~~~~~~~~~~~~~~~~~~~~~
have_higher_than_11mbit is only set to true some of the time in
ieee80211_get_rates() but is checked all of the time. So
have_higher_than_11mbit needs to be initialized to false.
Fixes: 5d6a1b069b ("mac80211: set basic rates earlier")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211223162848.3243702-1-trix@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Submitting AP probe/null during suspend can cause unexpected
disconnect on resume because of timeout waiting for ack status:
wlan0: Failed to send nullfunc to AP 11:22:33:44:55:66 after 500ms, disconnecting
This is especially the case when we enter suspend when a scan is
ongoing, indeed, scan is cancelled from __ieee80211_suspend, leading
to a corresponding (aborted) scan complete event, which in turn causes
the submission of an immediate monitor null frame (restart_sta_timer).
The corresponding packet or ack will not be processed before resuming,
causing a timeout & disconnect on resume.
Delay the AP probing when suspending/suspended.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1634805927-1113-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In function ieee80211_prep_channel(), it has some ieee80211_bss_get_ie()
and cfg80211_find_ext_ie() to get the IE, this is to use another
function ieee802_11_parse_elems() to get all the IEs in one time.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210924100052.32029-6-wgong@codeaurora.org
[remove now unnecessary size validation, use -ENOMEM, free elems earlier
for less error handling code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the 802.11 spec evolves, we need to parse more and more
elements. This is causing the struct to grow, and we can no
longer get away with putting it on the stack.
Change the API to always dynamically allocate and return an
allocated pointer that must be kfree()d later.
As an alternative, I contemplated a scheme whereby we'd say
in the code which elements we needed, e.g.
DECLARE_ELEMENT_PARSER(elems,
SUPPORTED_CHANNELS,
CHANNEL_SWITCH,
EXT(KEY_DELIVERY));
ieee802_11_parse_elems(..., &elems, ...);
and while I think this is possible and will save us a lot
since most individual places only care about a small subset
of the elements, it ended up being a bit more work since a
lot of places do the parsing and then pass the struct to
other functions, sometimes with multiple levels.
Link: https://lore.kernel.org/r/20210920154009.26caff6b5998.I05ae58768e990e611aee8eca8abefd9d7bc15e05@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg says:
====================
Another set of updates, all over the map:
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After channel switch, we should consider any beacon with a
CSA IE as a new switch. If the CSA IE is a leftover from
before the switch that the AP forgot to remove, we'll get
a CSA-to-Self.
This caused issues in iwlwifi where the firmware saw a beacon
with a CSA-to-Self with mode = 1 on the new channel after a
switch. The firmware considered this a new switch and closed
its queues. Since the beacon didn't change between before and
after the switch, we wouldn't handle it (the CRC is the same)
and we wouldn't let the firmware open its queues again or
disconnect if the CSA IE stays for too long.
Clear the CRC valid state after we switch to make sure that
we handle the beacon and handle the CSA IE as required.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210408143124.b9e68aa98304.I465afb55ca2c7d59f7bf610c6046a1fd732b4c28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The incorrect timeout check caused probing to happen when it did
not need to happen. This in turn caused tx performance drop
for around 5 seconds in ath10k-ct driver. Possibly that tx drop
is due to a secondary issue, but fixing the probe to not happen
when traffic is running fixes the symptom.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Fixes: 9abf4e4983 ("mac80211: optimize station connection monitor")
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210330230749.14097-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We observed some Cisco APs sending the following HE Operation IE in
associate response:
ff 0a 24 f4 3f 00 01 fc ff 00 00 00
Its HE operation parameter is 0x003ff4, so the expected total length is
7 which does not match the actual length = 10. This causes association
failing with "HE AP is missing HE Capability/operation."
According to P802.11ax_D4 Table9-94, HE operation is extensible, and
according to 802.11-2016 10.27.8, STA should discard the part beyond
the maximum length and parse the truncated element.
Allow HE operation element to be longer than expected to handle this
case and future extensions.
Fixes: e4d005b80d ("mac80211: refactor extended element parsing")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org>
Link: https://lore.kernel.org/r/20210223051926.2653301-1-yenlinlai@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
