After a new receiver peer has been added to the broadcast transmission
link, we allow immediate transmission of new broadcast packets, trusting
that the new peer will not accept the packets until it has received the
previously sent unicast broadcast initialiation message. In the same
way, the sender must not accept any acknowledges until it has itself
received the broadcast initialization from the peer, as well as
confirmation of the reception of its own initialization message.
Furthermore, when a receiver peer goes down, the sender has to produce
the missing acknowledges from the lost peer locally, in order ensure
correct release of the buffers that were expected to be acknowledged by
the said peer.
In a highly stressed system we have observed that contact with a peer
may come up and be lost before the above mentioned broadcast initial-
ization and confirmation have been received. This leads to the locally
produced acknowledges being rejected, and the non-acknowledged buffers
to linger in the broadcast link transmission queue until it fills up
and the link goes into permanent congestion.
In this commit, we remedy this by temporarily setting the corresponding
broadcast receive link state to ESTABLISHED and the 'bc_peer_is_up'
state to true before we issue the local acknowledges. This ensures that
those acknowledges will always be accepted. The mentioned state values
are restored immediately afterwards when the link is reset.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At first contact between two nodes, an endpoint might sometimes have
time to send out a LINK_PROTOCOL/STATE packet before it has received
the broadcast initialization packet from the peer, i.e., before it has
received a valid broadcast packet number to add to the 'bc_ack' field
of the protocol message.
This means that the peer endpoint will receive a protocol packet with an
invalid broadcast acknowledge value of 0. Under unlucky circumstances
this may lead to the original, already received acknowledge value being
overwritten, so that the whole broadcast link goes stale after a while.
We fix this by delaying the setting of the link field 'bc_peer_is_up'
until we know that the peer really has received our own broadcast
initialization message. The latter is always sent out as the first
unicast message on a link, and always with seqeunce number 1. Because
of this, we only need to look for a non-zero unicast acknowledge value
in the arriving STATE messages, and once that is confirmed we know we
are safe and can set the mentioned field. Before this moment, we must
ignore all broadcast acknowledges from the peer.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Trofimovich reported that pulse audio sends SCM_CREDENTIALS
as a control message to TCP. Since __sock_cmsg_send does not
support SCM_RIGHTS and SCM_CREDENTIALS, it returns an error and
hence breaks pulse audio over TCP.
SCM_RIGHTS and SCM_CREDENTIALS are sent on the SOL_SOCKET layer
but they semantically belong to SOL_UNIX. Since all
cmsg-processing functions including sock_cmsg_send ignore control
messages of other layers, it is best to ignore SCM_RIGHTS
and SCM_CREDENTIALS for consistency (and also for fixing pulse
audio over TCP).
Fixes: c14ac9451c ("sock: enable timestamping using control messages")
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Reported-by: Sergei Trofimovich <slyfox@gentoo.org>
Tested-by: Sergei Trofimovich <slyfox@gentoo.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vegard Nossum is reporting for a crash in fib_dump_info
when nh_dev = NULL and fib_nhs == 1:
Pid: 50, comm: netlink.exe Not tainted 4.7.0-rc5+
RIP: 0033:[<00000000602b3d18>]
RSP: 0000000062623890 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 000000006261b800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000024 RDI: 000000006245ba00
RBP: 00000000626238f0 R08: 000000000000029c R09: 0000000000000000
R10: 0000000062468038 R11: 000000006245ba00 R12: 000000006245ba00
R13: 00000000625f96c0 R14: 00000000601e16f0 R15: 0000000000000000
Kernel panic - not syncing: Kernel mode fault at addr 0x2e0, ip 0x602b3d18
CPU: 0 PID: 50 Comm: netlink.exe Not tainted 4.7.0-rc5+ #581
Stack:
626238f0 960226a02 00000400 000000fe
62623910 600afca7 62623970 62623a48
62468038 00000018 00000000 00000000
Call Trace:
[<602b3e93>] rtmsg_fib+0xd3/0x190
[<602b6680>] fib_table_insert+0x260/0x500
[<602b0e5d>] inet_rtm_newroute+0x4d/0x60
[<60250def>] rtnetlink_rcv_msg+0x8f/0x270
[<60267079>] netlink_rcv_skb+0xc9/0xe0
[<60250d4b>] rtnetlink_rcv+0x3b/0x50
[<60265400>] netlink_unicast+0x1a0/0x2c0
[<60265e47>] netlink_sendmsg+0x3f7/0x470
[<6021dc9a>] sock_sendmsg+0x3a/0x90
[<6021e0d0>] ___sys_sendmsg+0x300/0x360
[<6021fa64>] __sys_sendmsg+0x54/0xa0
[<6021fac0>] SyS_sendmsg+0x10/0x20
[<6001ea68>] handle_syscall+0x88/0x90
[<600295fd>] userspace+0x3fd/0x500
[<6001ac55>] fork_handler+0x85/0x90
$ addr2line -e vmlinux -i 0x602b3d18
include/linux/inetdevice.h:222
net/ipv4/fib_semantics.c:1264
Problem happens when RTNH_F_LINKDOWN is provided from user space
when creating routes that do not use the flag, catched with
netlink fuzzer.
Currently, the kernel allows user space to set both flags
to nh_flags and fib_flags but this is not intentional, the
assumption was that they are not set. Fix this by rejecting
both flags with EINVAL.
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Fixes: 0eeb075fad ("net: ipv4 sysctl option to ignore routes when nexthop link is down")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Cc: Andy Gospodarek <gospo@cumulusnetworks.com>
Cc: Dinesh Dutt <ddutt@cumulusnetworks.com>
Cc: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yue Cao claims that current host rate limiting of challenge ACKS
(RFC 5961) could leak enough information to allow a patient attacker
to hijack TCP sessions. He will soon provide details in an academic
paper.
This patch increases the default limit from 100 to 1000, and adds
some randomization so that the attacker can no longer hijack
sessions without spending a considerable amount of probes.
Based on initial analysis and patch from Linus.
Note that we also have per socket rate limiting, so it is tempting
to remove the host limit in the future.
v2: randomize the count of challenge acks per second, not the period.
Fixes: 282f23c6ee ("tcp: implement RFC 5961 3.2")
Reported-by: Yue Cao <ycao009@ucr.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If socket filter truncates an udp packet below the length of UDP header
in udpv6_queue_rcv_skb() or udp_queue_rcv_skb(), it will trigger a
BUG_ON in skb_pull_rcsum(). This BUG_ON (and therefore a system crash if
kernel is configured that way) can be easily enforced by an unprivileged
user which was reported as CVE-2016-6162. For a reproducer, see
http://seclists.org/oss-sec/2016/q3/8
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix possible NULL pointer dereference for vlan_insert_tag (two patches)
- Fix reference handling in some features, which may lead to reference
leaks or invalid memory access (four patches)
- Fix speedy join: DHCP packets handled by the gateway feature should
be sent with 4-address unicast instead of 3-address unicast to make
speedy join work. This fixes/speeds up DHCP assignment for clients
which join a mesh for the first time. (one patch)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Z04
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20160708' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are a couple batman-adv bugfix patches, all by Sven Eckelmann:
- Fix possible NULL pointer dereference for vlan_insert_tag (two patches)
- Fix reference handling in some features, which may lead to reference
leaks or invalid memory access (four patches)
- Fix speedy join: DHCP packets handled by the gateway feature should
be sent with 4-address unicast instead of 3-address unicast to make
speedy join work. This fixes/speeds up DHCP assignment for clients
which join a mesh for the first time. (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the prep work I did before enabling BH while handling socket backlog,
I missed two points in DCCP :
1) dccp_v4_ctl_send_reset() uses bh_lock_sock(), assuming BH were
blocked. It is not anymore always true.
2) dccp_v4_route_skb() was using __IP_INC_STATS() instead of
IP_INC_STATS()
A similar fix was done for TCP, in commit 47dcc20a39
("ipv4: tcp: ip_send_unicast_reply() is not BH safe")
Fixes: 7309f8821f ("dccp: do not assume DCCP code is non preemptible")
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Speedy join only works when the received packet is either broadcast or an
4addr unicast packet. Thus packets converted from broadcast to unicast via
the gateway handling code have to be converted to 4addr packets to allow
the receiving gateway server to add the sender address as temporary entry
to the translation table.
Not doing it will make the batman-adv gateway server drop the DHCP response
in many situations because it doesn't yet have the TT entry for the
destination of the DHCP response.
Fixes: 371351731e ("batman-adv: change interface_rx to get orig node")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
No support for pbss results in a memory leak for the acl_data
(if parse_acl_data succeeds). Fix this by moving the ACL parsing later.
Cc: stable@vger.kernel.org
Fixes: 34d505193b ("cfg80211: basic support for PBSS network type")
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 9c7370a166 ("ipv6: Fix a potential deadlock when creating pcpu rt")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Tested-by: Petr Novopashenniy <pety@rusnet.ru>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
dn_fib_count_nhs() could enter an infinite loop if nhp->rtnh_len == 0
(i.e. if userspace passes a malformed netlink message).
Let's use the helpers from net/nexthop.h which take care of all this
stuff. We can do exactly the same as e.g. fib_count_nexthops() and
fib_get_nhs() from net/ipv4/fib_semantics.c.
This fixes the softlockup for me.
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The orig_ifinfo reference counter for last_bonding_candidate in
batadv_orig_node has to be reduced when an originator node is released.
Otherwise the orig_ifinfo is leaked and the reference counter the netdevice
is not reduced correctly.
Fixes: f3b3d90189 ("batman-adv: add bonding again")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The replacement of last_bonding_candidate in batadv_orig_node has to be an
atomic operation. Otherwise it is possible that the reference counter of a
batadv_orig_ifinfo is reduced which was no longer the
last_bonding_candidate when the new candidate is added. This can either
lead to an invalid memory access or to reference leaks which make it
impossible to an interface which was added to batman-adv.
Fixes: f3b3d90189 ("batman-adv: add bonding again")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The pointer batadv_bla_claim::backbone_gw can be changed at any time.
Therefore, access to it must be protected to ensure that two function
accessing the same backbone_gw are actually accessing the same. This is
especially important when the crc_lock is used or when the backbone_gw of a
claim is exchanged.
Not doing so leads to invalid memory access and/or reference leaks.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Fixes: 5a1dd8a477 ("batman-adv: lock crc access in bridge loop avoidance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_orig_node_new uses batadv_orig_node_vlan_new to allocate a new
batadv_orig_node_vlan and add it to batadv_orig_node::vlan_list. References
to this list have also to be cleaned when the batadv_orig_node is removed.
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
vlan_insert_tag can return NULL on errors. The distributed arp table code
therefore has to check the return value of vlan_insert_tag for NULL before
it can safely operate on this pointer.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
vlan_insert_tag can return NULL on errors. The bridge loop avoidance code
therefore has to check the return value of vlan_insert_tag for NULL before
it can safely operate on this pointer.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
If register_pernet_subsys() fails, we shouldn't try to call
unregister_pernet_subsys().
Fixes: 467fa15356 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.")
Cc: stable@vger.kernel.org
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect use of nla_strlcpy() where the first NLA_HDRLEN bytes
of the link name where left out.
Making the output of tipc-config -ls look something like:
Link statistics:
dcast-link
1:data0-1.1.2:data0
1:data0-1.1.3:data0
Also, for the record, the patch that introduce this regression
claims "Sending the whole object out can cause a leak". Which isn't
very likely as this is a compat layer, where the data we are parsing
is generated by us and we know the string to be NULL terminated. But
you can of course never be to secure.
Fixes: 5d2be1422e (tipc: fix an infoleak in tipc_nl_compat_link_dump)
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 9b368814b3 ("net: fix bridge multicast packet checksum validation")
we need to fixup the checksum for CHECKSUM_COMPLETE when
pushing skb on RX path. Otherwise we get similar splats.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People who use PACKET_FANOUT_HASH want a symmetric hash, meaning that
they want packets going in both directions on a flow to hash to the
same bucket.
The core kernel SKB hash became non-symmetric when the ipv6 flow label
and other entities were incorporated into the standard flow hash order
to increase entropy.
But there are no users of PACKET_FANOUT_HASH who want an assymetric
hash, they all want a symmetric one.
Therefore, use the flow dissector to compute a flat symmetric hash
over only the protocol, addresses and ports. This hash does not get
installed into and override the normal skb hash, so this change has
no effect whatsoever on the rest of the stack.
Reported-by: Eric Leblond <eric@regit.org>
Tested-by: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_skb_dst_mtu uses skb->sk, assuming it is an AF_INET socket (e.g. it
calls ip_sk_use_pmtu which casts sk as an inet_sk).
However, in the case of UDP tunneling, the skb->sk is not necessarily an
inet socket (could be AF_PACKET socket, or AF_UNSPEC if arriving from
tun/tap).
OTOH, the sk passed as an argument throughout IP stack's output path is
the one which is of PMTU interest:
- In case of local sockets, sk is same as skb->sk;
- In case of a udp tunnel, sk is the tunneling socket.
Fix, by passing ip_finish_output's sk to ip_skb_dst_mtu.
This augments 7026b1ddb6 'netfilter: Pass socket pointer down through okfn().'
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"I've been traveling so this accumulates more than week or so of bug
fixing. It perhaps looks a little worse than it really is.
1) Fix deadlock in ath10k driver, from Ben Greear.
2) Increase scan timeout in iwlwifi, from Luca Coelho.
3) Unbreak STP by properly reinjecting STP packets back into the
stack. Regression fix from Ido Schimmel.
4) Mediatek driver fixes (missing malloc failure checks, leaking of
scratch memory, wrong indexing when mapping TX buffers, etc.) from
John Crispin.
5) Fix endianness bug in icmpv6_err() handler, from Hannes Frederic
Sowa.
6) Fix hashing of flows in UDP in the ruseport case, from Xuemin Su.
7) Fix netlink notifications in ovs for tunnels, delete link messages
are never emitted because of how the device registry state is
handled. From Nicolas Dichtel.
8) Conntrack module leaks kmemcache on unload, from Florian Westphal.
9) Prevent endless jump loops in nft rules, from Liping Zhang and
Pablo Neira Ayuso.
10) Not early enough spinlock initialization in mlx4, from Eric
Dumazet.
11) Bind refcount leak in act_ipt, from Cong WANG.
12) Missing RCU locking in HTB scheduler, from Florian Westphal.
13) Several small MACSEC bug fixes from Sabrina Dubroca (missing RCU
barrier, using heap for SG and IV, and erroneous use of async flag
when allocating AEAD conext.)
14) RCU handling fix in TIPC, from Ying Xue.
15) Pass correct protocol down into ipv4_{update_pmtu,redirect}() in
SIT driver, from Simon Horman.
16) Socket timer deadlock fix in TIPC from Jon Paul Maloy.
17) Fix potential deadlock in team enslave, from Ido Schimmel.
18) Memory leak in KCM procfs handling, from Jiri Slaby.
19) ESN generation fix in ipv4 ESP, from Herbert Xu.
20) Fix GFP_KERNEL allocations with locks held in act_ife, from Cong
WANG.
21) Use after free in netem, from Eric Dumazet.
22) Uninitialized last assert time in multicast router code, from Tom
Goff.
23) Skip raw sockets in sock_diag destruction broadcast, from Willem
de Bruijn.
24) Fix link status reporting in thunderx, from Sunil Goutham.
25) Limit resegmentation of retransmit queue so that we do not
retransmit too large GSO frames. From Eric Dumazet.
26) Delay bpf program release after grace period, from Daniel
Borkmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (141 commits)
openvswitch: fix conntrack netlink event delivery
qed: Protect the doorbell BAR with the write barriers.
neigh: Explicitly declare RCU-bh read side critical section in neigh_xmit()
e1000e: keep VLAN interfaces functional after rxvlan off
cfg80211: fix proto in ieee80211_data_to_8023 for frames without LLC header
qlcnic: use the correct ring in qlcnic_83xx_process_rcv_ring_diag()
bpf, perf: delay release of BPF prog after grace period
net: bridge: fix vlan stats continue counter
tcp: do not send too big packets at retransmit time
ibmvnic: fix to use list_for_each_safe() when delete items
net: thunderx: Fix TL4 configuration for secondary Qsets
net: thunderx: Fix link status reporting
net/mlx5e: Reorganize ethtool statistics
net/mlx5e: Fix number of PFC counters reported to ethtool
net/mlx5e: Prevent adding the same vxlan port
net/mlx5e: Check for BlueFlame capability before allocating SQ uar
net/mlx5e: Change enum to better reflect usage
net/mlx5: Add ConnectX-5 PCIe 4.0 to list of supported devices
net/mlx5: Update command strings
net: marvell: Add separate config ANEG function for Marvell 88E1111
...
* fix mesh peer link counter, decrement wasn't always done at all
* fix ethertype (length) for packets without RFC 1042 or bridge
tunnel header
-----BEGIN PGP SIGNATURE-----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=dAbs
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-06-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two small fixes
* fix mesh peer link counter, decrement wasn't always done at all
* fix ethertype (length) for packets without RFC 1042 or bridge
tunnel header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first and last netlink message for a particular conntrack are
actually sent. The first message is sent through nf_conntrack_confirm when
the conntrack is committed. The last one is sent when the conntrack is
destroyed on timeout. The other conntrack state change messages are not
advertised.
When the conntrack subsystem is used from netfilter, nf_conntrack_confirm
is called for each packet, from the postrouting hook, which in turn calls
nf_ct_deliver_cached_events to send the state change netlink messages.
This commit fixes the problem by calling nf_ct_deliver_cached_events in the
non-commit case as well.
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
CC: Joe Stringer <joestringer@nicira.com>
CC: Justin Pettit <jpettit@nicira.com>
CC: Andy Zhou <azhou@nicira.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.
More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.
When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.
This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.
Fixes: 4fd3d7d9e8 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes: 2d1c304cb2 ("cfg80211: add function for 802.3 conversion with separate output buffer")
Cc: stable@vger.kernel.org
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
I made a dumb off-by-one mistake when I added the vlan stats counter
dumping code. The increment should happen before the check, not after
otherwise we miss one entry when we continue dumping.
Fixes: a60c090361 ("bridge: netlink: export per-vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun reported a bug in TCP stack and bisected it to a recent commit.
In case where we process SACK, we can coalesce multiple skbs
into fat ones (tcp_shift_skb_data()), to lower write queue
overhead, because we do not expect to retransmit these packets.
However, SACK reneging can happen, forcing the sender to retransmit
all these packets. If skb->len is above 64KB, we then send buggy
IP packets that could hang TSO engine on cxgb4.
Neal suggested to use tcp_tso_autosize() instead of tp->gso_segs
so that we cook packets of optimal size vs TCP/pacing.
Thanks to Arjun for reporting the bug and running the tests !
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Arjun V <arjun@chelsio.com>
Tested-by: Arjun V <arjun@chelsio.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The untagged vlan object is only destroyed when the interface is removed
via the legacy sysfs interface. But it also has to be destroyed when the
standard rtnl-link interface is used.
Fixes: 5d2c05b213 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_linearize may reallocate the skb. This makes the calculated pointer
for ethhdr invalid. But it the pointer is used later to fill in the RR
field of the batadv_icmp_packet_rr packet.
Instead re-evaluate eth_hdr after the skb_linearize+skb_cow to fix the
pointer and avoid the invalid read.
Fixes: da6b8c20a5 ("batman-adv: generalize batman-adv icmp packet handling")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each batadv_tt_local_entry hold a single reference to a
batadv_softif_vlan. In case a new entry cannot be added to the hash
table, the error path puts the reference, but the reference will also
now be dropped by batadv_tt_local_entry_release().
Fixes: a33d970d0b ("batman-adv: Fix reference counting of vlan object for tt_local_entry")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tt_req_node is added and removed from a list inside a spinlock. But the
locking is sometimes removed even when the object is still referenced and
will be used later via this reference. For example batadv_send_tt_request
can create a new tt_req_node (including add to a list) and later
re-acquires the lock to remove it from the list and to free it. But at this
time another context could have already removed this tt_req_node from the
list and freed it.
CPU#0
batadv_batman_skb_recv from net_device 0
-> batadv_iv_ogm_receive
-> batadv_iv_ogm_process
-> batadv_iv_ogm_process_per_outif
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_ogm_handler_v1
-> batadv_tt_update_orig
-> batadv_send_tt_request
-> batadv_tt_req_node_new
spin_lock(...)
allocates new tt_req_node and adds it to list
spin_unlock(...)
return tt_req_node
CPU#1
batadv_batman_skb_recv from net_device 1
-> batadv_recv_unicast_tvlv
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_unicast_handler_v1
-> batadv_handle_tt_response
spin_lock(...)
tt_req_node gets removed from list and is freed
spin_unlock(...)
CPU#0
<- returned to batadv_send_tt_request
spin_lock(...)
tt_req_node gets removed from list and is freed
MEMORY CORRUPTION/SEGFAULT/...
spin_unlock(...)
This can only be solved via reference counting to allow multiple contexts
to handle the list manipulation while making sure that only the last
context holding a reference will free the object.
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Amadeus Alfa <amadeus@chemnitz.freifunk.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VLAN tagged frame is received and the corresponding VLAN is not
configured on the soft interface, it will splat a WARN on every packet
received. This is a quite annoying behaviour for some scenarios, e.g. if
bat0 is bridged with eth0, and there are arbitrary VLAN tagged frames
from Ethernet coming in without having any VLAN configuration on bat0.
The code should probably create vlan objects on the fly and
transparently transport these VLAN-tagged Ethernet frames, but until
this is done, at least the WARN splat should be replaced by a rate
limited output.
Fixes: 354136bcc3 ("batman-adv: fix kernel crash due to missing NULL checks")
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
This fixes wrong-interface signaling on 32-bit platforms for entries
created when jiffies > 2^31 + MFC_ASSERT_THRESH.
Signed-off-by: Tom Goff <thomas.goff@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places where the listener and pending or accept queue
child sockets are accessed at the same time. Lockdep is unhappy that
two locks from the same class are held.
Tell lockdep that it is safe and document the lock ordering.
Originally Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> sent a similar
patch asking whether this is safe. I have audited the code and also
covered the vsock_pending_work() function.
Suggested-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with the commit 8c14586fc3 ("net: ipv6: Use passed in table for
nexthop lookups"), net hop lookup is first performed on route creation
in the passed-in table.
However device match is not enforced in table lookup, so the found
route can be later discarded due to egress device mismatch and no
global lookup will be performed.
This cause the following to fail:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip route add 2001:db8:8086::/48 dev dummy1 metric 20
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy1 metric 20
ip route add 2001:db8:8086::/48 dev dummy2 metric 21
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy2 metric 21
RTNETLINK answers: No route to host
This change fixes the issue enforcing device lookup in
ip6_nh_lookup_table()
v1->v2: updated commit message title
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Reported-and-tested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the packet was dropped by lower qdisc, then we must not
access it later.
Save qdisc_pkt_len(skb) in a temp variable.
Fixes: 2ccccf5fb4 ("net_sched: update hierarchical backlog too")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey reported that we have GFP_KERNEL allocation when
holding the spinlock tcf_lock. Actually we don't have
to take that spinlock for all the cases, especially
for the new one we just create. To modify the existing
actions, we still need this spinlock to make sure
the whole update is atomic.
For net-next, we can get rid of this spinlock because
we already hold the RTNL lock on slow path, and on fast
path we can use RCU to protect the metalist.
Joint work with Jamal.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blair Steven noticed that ESN in conjunction with UDP encapsulation
is broken because we set the temporary ESP header to the wrong spot.
This patch fixes this by first of all using the right spot, i.e.,
4 bytes off the real ESP header, and then saving this information
so that after encryption we can restore it properly.
Fixes: 7021b2e1cd ("esp4: Switch to new AEAD interface")
Reported-by: Blair Steven <Blair.Steven@alliedtelesis.co.nz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When extracting an individual message from a received "bundle" buffer,
we just create a clone of the base buffer, and adjust it to point into
the right position of the linearized data area of the latter. This works
well for regular message reception, but during periods of extremely high
load it may happen that an extracted buffer, e.g, a connection probe, is
reversed and forwarded through an external interface while the preceding
extracted message is still unhandled. When this happens, the header or
data area of the preceding message will be partially overwritten by a
MAC header, leading to unpredicatable consequences, such as a link
reset.
We now fix this by ensuring that the msg_reverse() function never
returns a cloned buffer, and that the returned buffer always contains
sufficient valid head and tail room to be forwarded.
Reported-by: Erik Hugne <erik.hugne@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every open of /proc/net/kcm leaks 16 bytes of memory as is reported by
kmemleak:
unreferenced object 0xffff88059c0e3458 (size 192):
comm "cat", pid 1401, jiffies 4294935742 (age 310.720s)
hex dump (first 32 bytes):
28 45 71 96 05 88 ff ff 00 10 00 00 00 00 00 00 (Eq.............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff8156a2de>] kmem_cache_alloc_trace+0x16e/0x230
[<ffffffff8162a479>] seq_open+0x79/0x1d0
[<ffffffffa0578510>] kcm_seq_open+0x0/0x30 [kcm]
[<ffffffff8162a479>] seq_open+0x79/0x1d0
[<ffffffff8162a8cf>] __seq_open_private+0x2f/0xa0
[<ffffffff81712548>] seq_open_net+0x38/0xa0
...
It is caused by a missing free in the ->release path. So fix it by
providing seq_release_net as the ->release method.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: cd6e111bf5 (kcm: Add statistics and proc interfaces)
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tom Herbert <tom@herbertland.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style issues in the following files:
ib_cm.c: add space
loop.c: convert spaces to tabs
sysctl.c: add space
tcp.h: convert spaces to tabs
tcp_connect.c:remove extra indentation in switch statement
tcp_recv.c: convert spaces to tabs
tcp_send.c: convert spaces to tabs
transport.c: move brace up one line on for statement
Signed-off-by: Joshua Houghton <josh@awful.name>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A socket connection made in ax.25 is not closed when session is
completed. The heartbeat timer is stopped prematurely and this is
where the socket gets closed. Allow heatbeat timer to run to close
socket. Symptom occurs in kernels >= 4.2.0
Originally sent 6/15/2016. Resend with distribution list matching
scripts/maintainer.pl output.
Signed-off-by: Basil Gunn <basil@pacabunga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
