No need to check for "DWC2_POWER_DOWN_PARAM_HIBERNATION" param
as "hsotg->hibernated" flag is already enough for exiting from
hibernation mode.
- Removes checking of "DWC2_POWER_DOWN_PARAM_HIBERNATION" param.
- For code readability Hibernation exit code moved after
debug message print.
- Added "dwc2_exit_hibernation()" function error checking.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124651.51C8DA005C@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.13-rc1, including:
- better type detection for pl2303
- support for more line speeds for pl2303 (TA/TB)
- fixed CSIZE handling for the new xr driver
- core support for multi-interface functions
- TIOCGSERIAL and TIOCSSERIAL fixes
- generic TIOCSSERIAL support (e.g. for closing_wait)
- fixed return value for unsupported ioctls
- support for gpio valid masks in cp210x
- drain-delay fixes and improvements
- support for multi-port devices for xr
- generalisation of the xr driver to support three new device classes
(XR21B142X, XR21B1411 and XR2280X)
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYIE2iwAKCRALxc3C7H1l
CFJsAQCd6rX6VyteR6RUmmTjmGDyRwxsXGniw9bf36dzhlKncwEAga2E+47FGHYm
YiNQzfcETfjGO21usS1BWhNvzf/gsgs=
=1FU1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.13-rc1
Here are the USB-serial updates for 5.13-rc1, including:
- better type detection for pl2303
- support for more line speeds for pl2303 (TA/TB)
- fixed CSIZE handling for the new xr driver
- core support for multi-interface functions
- TIOCGSERIAL and TIOCSSERIAL fixes
- generic TIOCSSERIAL support (e.g. for closing_wait)
- fixed return value for unsupported ioctls
- support for gpio valid masks in cp210x
- drain-delay fixes and improvements
- support for multi-port devices for xr
- generalisation of the xr driver to support three new device classes
(XR21B142X, XR21B1411 and XR2280X)
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (72 commits)
USB: cdc-acm: add more Maxlinear/Exar models to ignore list
USB: serial: xr: add copyright notice
USB: serial: xr: reset FIFOs on open
USB: serial: xr: add support for XR22801, XR22802, XR22804
USB: serial: xr: add support for XR21B1411
USB: serial: xr: add support for XR21B1421, XR21B1422 and XR21B1424
USB: serial: xr: add type abstraction
USB: serial: xr: drop type prefix from shared defines
USB: serial: xr: move pin configuration to probe
USB: serial: xr: rename GPIO-pin defines
USB: serial: xr: rename GPIO-mode defines
USB: serial: xr: add support for XR21V1412 and XR21V1414
USB: serial: ti_usb_3410_5052: clean up termios CSIZE handling
USB: serial: ti_usb_3410_5052: use kernel types consistently
USB: serial: ti_usb_3410_5052: add port-command helpers
USB: serial: ti_usb_3410_5052: clean up vendor-request helpers
USB: serial: ti_usb_3410_5052: drop unnecessary packed attributes
USB: serial: io_ti: drop unnecessary packed attributes
USB: serial: io_ti: use kernel types consistently
USB: serial: io_ti: add read-port-command helper
...
The programming guide incorrectly stated that the DCFG.bInterval_m1 must
be set to 0 when operating in fullspeed. There's no such limitation for
all IPs. See DWC_usb3x programming guide section 3.2.2.1.
Fixes: a1679af85b ("usb: dwc3: gadget: Fix setting of DEPCFG.bInterval_m1")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/5d4139ae89d810eb0a2d8577fb096fc88e87bfab.1618472454.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PM will take care of the status of child device, so no need
check each port anymore.
Suggested-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618555706-6810-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2 driver has everything we need to run
in ACPI mode except for the ACPI module device table
boilerplate. With that added and identified as "BCM2848",
an id in use by other OSs for this device, the dw2
controller on the BCM2711 will work.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20210413215834.3126447-2-jeremy.linton@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
suspend() does its poisoning conditionally, resume() does it
unconditionally. On a device with combined interfaces this
will balance, on a device with two interfaces the counter will
go negative and resubmission will fail.
Both actions need to be done conditionally.
Fixes: 6069e3e927 ("USB: cdc-acm: untangle a circular dependency between callback and softint")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek Hub (0bda:5487) in Dell Dock WD19 sometimes fails to work
after the system resumes from suspend with remote wakeup enabled
device connected:
[ 1947.640907] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641208] usb 5-2.3-port5: cannot disable (err = -71)
[ 1947.641401] hub 5-2.3:1.0: hub_ext_port_status failed (err = -71)
[ 1947.641450] usb 5-2.3-port4: cannot reset (err = -71)
Information of this hub:
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 5
D: Ver= 2.10 Cls=09(hub ) Sub=00 Prot=02 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=5487 Rev= 1.47
S: Manufacturer=Dell Inc.
S: Product=Dell dock
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=01 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
I:* If#= 0 Alt= 1 #EPs= 1 Cls=09(hub ) Sub=00 Prot=02 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
The failure results from the ETIMEDOUT by chance when turning on
the suspend feature for the specified port of the hub. The port
seems to be in an unknown state so the hub_activate during resume
fails the hub_port_status, then the hub will fail to work.
The quirky hub needs the reset-resume quirk to function correctly.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210420174651.6202-1-chris.chiu@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable status is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed and move the
declaration of status to the scope where it is used.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420110622.377339-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable result is being assigned with a value that is
never read, the assignment is redundant and can be removed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210420113818.378478-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The START_TRANSFER command needs to be executed while in ON/U0 link
state (with an exception during register initialization). Don't use
dwc->link_state to check this since the driver only tracks the link
state when the link state change interrupt is enabled. Check the link
state from DSTS register instead.
Note that often the host already brings the device out of low power
before it sends/requests the next transfer. So, the user won't see any
issue when the device starts transfer then. This issue is more
noticeable in cases when the device delays starting transfer, which can
happen during delayed control status after the host put the device in
low power.
Fixes: 799e9dc829 ("usb: dwc3: gadget: conditionally disable Link State change events")
Cc: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/bcefaa9ecbc3e1936858c0baa14de6612960e909.1618884221.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon driver unbind usb_free_all_descriptors() function frees all
speed descriptor pointers without setting them to NULL. In case
gadget speed changes (i.e from super speed plus to super speed)
after driver unbind only upto super speed descriptor pointers get
populated. Super speed plus desc still holds the stale (already
freed) pointer. Fix this issue by setting all descriptor pointers
to NULL after freeing them in usb_free_all_descriptors().
Fixes: f5c61225cf ("usb: gadget: Update function for SuperSpeedPlus")
cc: stable@vger.kernel.org
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1619034452-17334-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
Fixes: e3a0720224 ("usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210415050121.1928298-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A dedicated wakeup irq will be used to handle runtime suspend/resume,
we use dev_pm_set_dedicated_wake_irq API to take care of requesting
and attaching wakeup irq, then the suspend/resume framework will help
to enable/disable wakeup irq.
The runtime PM is default off since some platforms may not support it.
users can enable it via power/control (set "auto") in sysfs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618031406-15347-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a PD charger advertising Rp-3.0 is connected to a sink port, the
sink port current limit would 3A, during SNK_DISCOVERY, till power
negotiation starts. Once the negotiation starts the power limit needs
to drop down to pSnkStby(500mA @ 5V) and to negotiated current limit
once the explicit contract is in place. Not all charging loops can ramp
up to 3A and drop down to 500mA within tSnkStdby which is 15ms. The port
partner might hard reset if tSnkStdby is not met.
To solve this problem, this patch introduces slow-charger-loop which
when set makes the port request PD_P_SNK_STDBY_MW upon entering
SNK_DISCOVERY(instead of 3A or the 1.5A during SNK_DISCOVERY) and the
actual currrent limit after RX of PD_CTRL_PSRDY for PD link or during
SNK_READY for non-pd link.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20210414024000.4175263-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a shutdown callback to USB DWC core driver to ensure that
it is properly shutdown in reboot/shutdown path. This is required
where SMMU address translation is enabled like on SC7180
SoC and few others. If the hardware is still accessing memory after
SMMU translation is disabled as part of SMMU shutdown callback in
system reboot or shutdown path, then IOVAs(I/O virtual address)
which it was using will go on the bus as the physical addresses which
might result in unknown crashes (NoC/interconnect errors).
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Link: https://lore.kernel.org/r/1618380209-20114-1-git-send-email-sanm@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the controller handles single stream only. So, Ignore Packet
Pending bit for stream selection and don't search for another stream if
the host sends Data Packet with PP=0 (for OUT direction) or ACK with
NumP=0 and PP=0 (for IN direction). This slightly improves the stream
performance.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/097ba9e104c143f7ba0195ebff29390ec3043692.1618282705.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another branded 8153 device that doesn't work well with LPM
enabled:
[ 400.597506] r8152 5-1.1:1.0 enx482ae3a2a6f0: Tx status -71
So disable LPM to resolve the issue.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1922651
Link: https://lore.kernel.org/r/20210412135455.791971-1-kai.heng.feng@canonical.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complains about a potential missing error code:
drivers/usb/typec/port-mapper.c:168 typec_link_port()
warn: missing error code 'ret'
This is a false positive and returning zero is intentional. Let's
re-arrange the code to silence the warning and make the intent more
clear.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YHadaACH8Mq/10F7@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the xr_serial got support for other models, add their USB IDs
as well.
The Maxlinear/Exar USB UARTs can be used in either ACM mode using the
cdc-acm driver or in "custom driver" mode in which further features such
as hardware and software flow control, GPIO control and in-band
line-status reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
correctly.
Ensure that cdc_acm will not bind to these devices if the custom
USB-serial driver is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/5155887a764cbc11f8da0217fe08a24a77d120b4.1616571453.git.mchehab+huawei@kernel.org
[ johan: rewrite commit message, clean up entries ]
Cc: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reset the transmit and receive FIFOs before enabling the UARTs as part
of open() in order to flush any stale data.
Note that the XR21V141X needs a type-specific implementation due to its
UART Manager registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR22801, XR22802 and XR22804 are compound devices with an embedded
hub and up to seven downstream USB devices including one, two or four
UARTs respectively.
The UART function is similar to XR21B142X but most registers are offset
by 0x40, the register requests are different and are directed at the
device rather than interface, and 5 and 6-bit words are not supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
The single-port XR21B1411 is similar to the XR21B142X type but uses
12-bit registers and 16-bit register addresses, the register requests
are different and are directed at the device rather than interface, and
5 and 6-bit words are not supported.
The register layout is very similar to XR21B142X except that most
registers are offset by 0xc00 (corresponding to a channel index of 12 in
the MSB of wIndex). As the device is single-port so that the derived
channel index is 0, the current register accessors can be reused after
simply changing the address width.
Signed-off-by: Johan Hovold <johan@kernel.org>
The XR21B1421, XR21B1422 and XR21B1424 are the one-, two- and four-port
models of a second XR21B142X type of the Maxlinear/Exar USB UARTs.
The XR21B142X type differs from XR21V141X in several ways, including:
- register layout
- register width (16-bit instead of 8-bit)
- vendor register requests
- UART enable/disable sequence
- custom-driver mode flag
- three additional GPIOs (9 instead of 6)
As for XR21V141X, the XR21B142X vendor requests encode the channel index
in the MSB of wIndex, but it lacks the UART Manager registers which
have been replaced by regular UART registers. The new type also uses the
interface number of the control interface (0, 2, 4, 6) as channel index
instead of the channel number (0, 1, 2, 3).
The XR21B142X lacks the divisor and format registers used by XR21V141X
and instead uses the CDC SET_LINE_CONTROL request to configure the line
settings.
Note that the currently supported XR21V141X type lacks the custom-driver
mode flag that prevents the device from entering CDC-ACM mode when a CDC
requests is received. This specifically means that the SET_LINE_CONTROL
request cannot be used with XR21V141X even though it is otherwise
supported.
The UART enable sequence for XR21B142X does not involve explicitly
enabling the FIFOs, but according to datasheet the UART must be disabled
when writing any register but GPIO_SET, GPIO_CLEAR, TX_BREAK and
ERROR_STATUS.
Signed-off-by: Johan Hovold <johan@kernel.org>
There are at least four types of Maxlinear/Exar USB UARTs which differ
in various ways such as in their register layouts:
XR21V141X
XR21B142X
XR21B1411
XR22804
It is not clear whether the device type can be inferred from the
descriptors so encode it in the device-id table for now.
Add a type structure that can be used to abstract the register layout
and other features, and use it when accessing the XR21V141X UART
registers that are shared by all types.
Note that the currently supported XR21V141X type is the only type that
has a set of UART Manager registers and that these will need to be
handled specifically.
Similarly, XR21V141X is the only type which has the divisor registers
and that needs to use the format register when configuring the line
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation for adding support for further types, drop the type
prefix from defines that are not specific to XR21V141X.
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to configure the pins on every open and judging from the
vendor driver and datasheet it can be done before enabling the UART.
Move pin configuration from open() to port probe and make sure to
deassert DTR and RTS after configuring all pins as GPIO.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add support for the two- and four-port variants of XR21V1410.
Use the interface number of each control interface (e.g. 0, 2, 4, 6) to
derive the zero-based channel index:
XR21V1410 0
XR21V1412 0, 1
XR21V1414 0, 1, 2, 3
Note that the UART registers reside in separate blocks per channel,
while the UART Manager functionality is implemented using per-channel
registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove the random white space from the CSIZE switch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add two port-command helpers to handle the UART module-id parameter
instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make the vendor-request helpers data parameters be void pointers and
drop the caller casts.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unnecessary packed attributes from structures that don't need it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop unnecessary packed attributes from structures that don't need it
and use the __packed macro consistently.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use kernel types consistently by replacing the remaining __uXX types.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a read-port-command helper analogous to the send-port-command
helper to take care of the UART module id instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a send-port-command helper which takes care of determining the UART
module id when sending commands instead of doing so at every call site.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the vendor-request helpers by using kernel-types consistently
and using void pointers for the data arguments, which allows removing
a cast from one caller.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Unlike the TUSB5052, the TUSB3410 has an LSR TEMT bit to tell if both
the transmitter data and shift registers are empty.
Make sure to check also the shift register on TUSB3410 when waiting for
the transmit buffer to drain during close and drop the time-based
one-char delay which is otherwise needed (e.g. 90 ms at 110 bps).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The three-character drain delay was added by commit f1175daa53 ("USB:
ti_usb_3410_5052: kill custom closing_wait") when removing the custom
closing-wait implementation, which used a fixed 20 ms poll period and
drain delay.
This was likely a bit too conservative as a one-character timeout (e.g.
33 ms at 300 bps) should be enough to compensate for the lack of a
transmitter empty bit in the TUSB5052 line-status register.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Document that the device line-status register doesn't tell when the
transmitter shift register has emptied and that this is why the
one-character drain delay is needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The f81232 driver now waits for the transmit FIFO to drain during close
so there is no need to keep the time-based drain delay, which would add
up to two seconds on every close for low line speeds.
Fixes: 98405f8103 ("USB: serial: f81232: add tx_empty function")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When dwc2 core is in clock gating mode loading driver
again causes driver fail. Because in that mode
registers are not accessible.
Added a flow of exiting clock gating mode
to avoid the driver reload failure.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073731.3C81BA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not hibernation nor partial power down are supported,
port resume is done using the clock gating programming flow.
Adds a new flow of exiting clock gating when PC is
resumed.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073723.BA0FEA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If not hibernation nor partial power down are supported,
clock gating is used to save power.
Adds a new flow of entering clock gating when PC is
suspended.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073716.30C13A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When core is in clock gating state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.
Added exit from clock gating state to avoid port
reset issue and process upper layer request properly.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073708.ADFC6A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates the implementation of exiting clock gating mode
when core receives port resume.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_exit_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073701.367E0A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updates the implementation of entering clock gating mode
when core receives port suspend.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_enter_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073653.9F493A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds clock gating exit flow when set port feature
reset is received in suspended state.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073646.27217A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added exit from clock gating mode when wakeup interrupt
is detected. To exit from the clock gating
in device mode "dwc2_gadget_exit_clock_gating()"
function is used with rem_wakeup parameter 0. To exit
clock gating in host mode "dwc2_host_exit_clock_gating()"
with rem_wakeup parameter 1.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073630.EF2CEA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If core doesn't support hibernation or partial power
down power saving options, power can still be saved
using clock gating on all the clocks.
- Added entering clock gating state from USB_SUSPEND
interrupt.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073623.65355A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added device clock gating support functions according
programming guide.
Moved "bus_suspended" flag to "dwc2_hsotg" struct because
we need to set that flag while entering to clock gating
in case when the driver is built in peripheral mode.
Added function names:
dwc2_gadget_enter_clock_gating()
dwc2_gadget_exit_clock_gating()
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073607.F41E8A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmB0S50ACgkQSFkpgVDW
cbthMggAnH0oPq93dipS9g2WhHxmwKGJimWTFU82RxuuX6MefvllXEkWCHJdPplp
dyKhzaFQxFksR7GJ8UCoZg3wg0rk38suLiN+W+k9re6QaHPFWJiMEm83mN3/YaNn
stVLiuMRl+VIApIIWbf3MW8/a3j9N5oRI+MbqmvhcA4TFu3Z1xTe9xhs8eDtzeUV
cGI6JbrZr5Q3pcsvvZPwj2nFgjJ7eYum9Z1CsAopHyVnYu/NK2jh2+W+L37dUSan
cwUOIRoNvSYNHyXFVszOEmfxtTAKiISQ7L4+8tXr4X+qC8tUNd8Rw1ow5BAo8gh+
bBL8+NZVVGoTvNpYPhLLUHncE5Fn9Q==
=+ZMP
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Several Cadence3 improvements are introduced in v5.13-rc1:
- Add recovery during resume if the controller was lost power at system suspend
- Reduce DMA memory footprint
- Other small improvements
* tag 'usb-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fixes issue with Configure Endpoint command
usb: cdnsp: remove redundant initialization of variable ret
usb: cdns3: delete repeated clear operations
usb: cdns3: Optimize DMA request buffer allocation
usb: cdns3: Use dma_pool_* api to alloc trb pool
usb: cdns3: fix static checker warning.
usb: cdns3: imx: mark cdns_imx_system_resume as __maybe_unused
usb: cdns3: trace: delete the trace parameter for request->trb
usb: cdns3: imx: add power lost support for system resume
usb: cdns3: add power lost support for system resume
Patch adds flag EP_UNCONFIGURED to detect whether endpoint was
unconfigured. This flag is set in cdnsp_reset_device after Reset Device
command. Among others this command disables all non control endpoints.
Flag is used in cdnsp_gadget_ep_disable to protect controller against
invoking Configure Endpoint command on disabled endpoint. Lack of this
protection in some cases caused that Configure Endpoint command completed
with Context State Error code completion.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
dma_alloc_coherent already zeroes out memory, so memset is not needed.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
dma_alloc_coherent() might fail on the platform with a small
DMA region.
To avoid such failure in cdns3_prepare_aligned_request_buf(),
dma_alloc_coherent() is replaced with dma_alloc_noncoherent()
to allocate aligned request buffer of dynamic length.
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Allocation of DMA coherent memory in atomic context using
dma_alloc_coherent() might fail on platforms with smaller
DMA region.
To fix it, dma_alloc_coherent() is replaced with dma_pool
API to allocate a smaller chunk of DMA coherent memory for
TRB rings.
Reported-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The patch c450e48eb570: "usb: cdns3: add power lost support for
system resume" from Feb 18, 2021, leads to the following static
checker warning:
drivers/usb/cdns3/core.c:551 cdns_resume()
error: uninitialized symbol 'ret'.
drivers/usb/cdns3/core.c
544
545 if (!role_changed) {
546 if (cdns->role == USB_ROLE_HOST)
547 ret = cdns_drd_host_on(cdns);
548 else if (cdns->role == USB_ROLE_DEVICE)
549 ret = cdns_drd_gadget_on(cdns);
"ret" is uninitialized at else branch.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The function cdns_imx_system_resume() may have no callers depending
on configuration, so it must be marked __maybe_unused to avoid
harmless warning:
drivers/usb/cdns3/cdns3-imx.c:378:12: warning:
'cdns_imx_system_resume' defined but not used [-Wunused-function]
378 | static int cdns_imx_system_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~
Fixes: 67982dfa59de ("usb: cdns3: imx: add power lost support for system resume")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
It is not correct using %pa to print virtual address of request->trb, and
it is hard to print its physical address due to the virtual address is
zero before using. It could use index (start_trb/end_trb) to know the
current trb position, so no matter virtual address or physical address
for request-trb is not so meaningful.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
imx need special handle when controller lost power
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
If the controller lost its power during the system suspend, we need
to do all initialiation operations.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <frank.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Add a debug printk to dump the GPIO configuration stored in EEPROM
during probe.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new GPIO valid-mask feature to inform gpiolib which pins are
available for use instead of handling that in a request callback.
This also allows user space to figure out which pins are available
through the chardev interface without having to request each pin in
turn.
Note that the return value when requesting an unavailable pin will now
be -EINVAL instead of -ENODEV.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add the missing unlock before return from function usbip_sockfd_store()
in the error handling case.
Fixes: bd8b820422 ("usbip: vudc synchronize sysfs code paths")
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408112305.1022247-1-yebin10@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In accordance with the USB HCD/DRD schema all the USB controllers are
supposed to have DT-nodes named with prefix "^usb(@.*)?". Since the
existing DT-nodes will be renamed in a subsequent patch let's fix the DWC3
Qcom-specific code to detect the DWC3 sub-node just by checking its
compatible string to match the "snps,dwc3". The semantic of the code
won't change seeing all the DWC USB3 nodes are supposed to have the
compatible property with any of those strings set.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210409113029.7144-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210410024818.65659-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return the exactly delay time given by root hub descriptor,
this helps to reduce resume time etc.
Due to the root hub descriptor is usually provided by the host
controller driver, if there is compatibility for a root hub,
we can fix it easily without affect other root hub
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1618017645-12259-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kunpeng920's EHCI controller does not have SBRN register.
Reading the SBRN register when the controller driver is
initialized will get 0.
When rebooting the EHCI driver, ehci_shutdown() will be called.
if the sbrn flag is 0, ehci_shutdown() will return directly.
The sbrn flag being 0 will cause the EHCI interrupt signal to
not be turned off after reboot. this interrupt that is not closed
will cause an exception to the device sharing the interrupt.
Therefore, the EHCI controller of Kunpeng920 needs to skip
the read operation of the SBRN register.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Link: https://lore.kernel.org/r/1617958081-17999-1-git-send-email-liulongfang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the port struct device rather than tty class device for debugging.
Note that while USB serial doesn't support serdev yet (due to serdev not
handling hotplugging), serdev ttys do not have a corresponding class
device and would have been logged using a "(NULL device *):" prefix.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e6 ("USB: allow users to run setserial with cdc-acm")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b401f8c4f4.
The offending commit claimed that trying to set the values reported back
by TIOCGSERIAL as a regular user could result in an -EPERM error when HZ
is 250, but that was never the case.
With HZ=250, the default 0.5 second value of close_delay is converted to
125 jiffies when set and is converted back to 50 centiseconds by
TIOCGSERIAL as expected (not 12 cs as was claimed, even if that was the
case before an earlier fix).
Comparing the internal current and new jiffies values is just fine to
determine if the value is about to change so drop the bogus workaround
(which was also backported to stable).
For completeness: With different default values for these parameters or
with a HZ value not divisible by two, the lack of rounding when setting
the default values in tty_port_init() could result in an -EPERM being
returned, but this is hardly something we need to worry about.
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for altmodes described in the usb-connector fwnode
associated with the Type-C controller by calling the new
typec_port_register_altmodes_from_fwnode() helper for this.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This can be used by Type-C controller drivers which use a standard
usb-connector fwnode, with altmodes sub-node, to describe the available
altmodes.
Note there are is no devicetree bindings documentation for the altmodes
node, this is deliberate. ATM the fwnodes used to register the altmodes
are only used internally to pass platform info from a drivers/platform/x86
driver to the type-c subsystem.
When a devicetree user of this functionally comes up and the dt-bindings
have been hashed out the internal use can be adjusted to match the
dt-bindings.
Currently the typec_port_register_altmodes() function expects
an "altmodes" child fwnode on port->dev with this "altmodes" fwnode having
child fwnodes itself with each child containing 2 integer properties:
1. A "svid" property, which sets the id of the altmode, e.g. displayport
altmode has a svid of 0xff01.
2. A "vdo" property, typically used as a bitmask describing the
capabilities of the altmode, the bits in the vdo are specified in the
specification of the altmode.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409134033.105834-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_role_switch_find_by_fwnode() returns a reference to the role-switch
which must be put by calling usb_role_switch_put().
usb_role_switch_put() calls module_put(sw->dev.parent->driver->owner),
add a matching try_module_get() to usb_role_switch_find_by_fwnode(),
making it behave the same as the other usb_role_switch functions
which return a reference.
This avoids a WARN_ON being hit at kernel/module.c:1158 due to the
module-refcount going below 0.
Fixes: c6919d5e0c ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210409124136.65591-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks are configured by devm_clk_bulk_get_all() in this driver. In
case of any error the clocks freeing will be handled automatically.
There is no need to explicitly free the clocks. Fix the same.
Fixes: 84770f028f ("usb: dwc3: Add driver for Xilinx platforms")
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel-doc run gave a warning for Xilinx DWC3 driver:
drivers/usb/dwc3/dwc3-xilinx.c:27: warning: expecting prototype for
dwc3(). Prototype was for XLNX_USB_PHY_RST_EN() instead
Basically it was due to an extra '*' in line:2. This patch fixes the same.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Link: https://lore.kernel.org/r/1617904448-74611-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408130831.56239-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
thus a pairing decrement is needed.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Link: https://lore.kernel.org/r/20210408091836.55227-1-cuibixuan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mutex lock can be initialized automatically with DEFINE_MUTEX()
rather than explicitly calling mutex_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20210405101434.14878-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to platform_get_resource can potentially return a NULL pointer
on failure, so add this check and return -EINVAL if it fails.
Fixes: c41442474a ("usb: gadget: R8A66597 peripheral controller support.")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Dereference null return")
Link: https://lore.kernel.org/r/20210406184510.433497-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
