Currently, every packet that matches a mirroring trigger (e.g., received
packets, buffer dropped packets) is mirrored. Spectrum-2 and later ASICs
support mirroring with probability, where every 1 in N matched packets
is mirrored.
Extend the API that creates the binding between the trigger and the SPAN
agent with a probability rate parameter, which is an attribute of the
trigger. Set it to '1' to maintain existing behavior.
Subsequent patches will use it to perform more sophisticated sampling,
by mirroring packets to the CPU with probability.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPAR and MPAGR registers are used to configure the binding between
the mirroring trigger (e.g., received packet) and the SPAN agent. Add
probability rate field, which will allow us to support sampling by
mirroring to the CPU.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets are mirrored to the CPU, the trap identifier with which the
packets are trapped is determined according to the session identifier of
the SPAN agent performing the mirroring. Packets that are trapped for
the same logical reason (e.g., buffer drops) should use the same session
identifier.
Currently, a single session is implicitly supported (identifier 0) and
is used for packets that are mirrored to the CPU due to buffer drops
(e.g., early drop).
Subsequent patches are going to mirror packets to the CPU due to
sampling, which will require a different session identifier.
Prepare for that by making the session identifier an attribute of the
SPAN agent.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of the delayed work in the SPAN module is to potentially
update the destination port and various encapsulation parameters of SPAN
agents that point to a VLAN device or a GRE tap. The destination port
can change following the insertion of a new route, for example.
SPAN agents that point to a physical port or the CPU port are static and
never change throughout the lifetime of the SPAN agent. Therefore, skip
over them in the delayed work.
This fixes an issue where the delayed work overwrites the policer
that was set on a SPAN agent pointing to the CPU. Modifying the delayed
work to inherit the original policer configuration is error-prone, as
the same will be needed for any new parameter.
Fixes: 4039504e6a ("mlxsw: spectrum_span: Allow setting policer on a SPAN agent")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Traffic mirroring modes that are in-chip implemented on egress need an
internal buffer to work. As the only client, the SPAN module was managing
the buffer so far. However logically it belongs to the buffers module. E.g.
buffer size validation needs to take the size of the internal buffer into
account.
Therefore move the related code from SPAN to spectrum_buffers. Move over
the callbacks that determine the minimum buffer size as a function of
maximum speed and MTU. Add a field describing the internal buffer to struct
mlxsw_sp_hdroom. Extend mlxsw_sp_hdroom_bufs_reset_sizes() to take care of
sizing the internal buffer as well. Change the SPAN module to invoke that
function and mlxsw_sp_hdroom_configure() like all the other hdroom clients.
Drop the now-unnecessary mlxsw_sp_span_port_buffer_disable().
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SBIB register configures the size of an internal buffer that the
Spectrum ASICs use when mirroring traffic on egress. This size should be
taken into account when validating that the port headroom buffers are not
larger than the chip can handle. Up until now this was not done, which is
incidentally not a problem, because the priority group buffers that mlxsw
auto-configures are small enough that the boundary condition could not be
violated.
However when dcbnl_setbuffer is implemented, the user has control over
sizes of PG buffers, and they might overshoot the headroom capacity.
However the size of the SBIB buffer depends on port speed, and that cannot
be vetoed. Therefore SBIB size should be deduced from maximum port speed.
Additionally, once the buffers are configured by hand, the user could get
into an uncomfortable situation where their MTU change requests get vetoed,
because the SBIB does not fit anymore. Therefore derive SBIB size from
maximum permissible MTU as well.
Remove all the code that adjusted the SBIB size whenever speed or MTU
changed.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unsetting policer base, the SPAN code currently uses refcount_dec().
However that function splats when the counter reaches zero, because
reaching zero without actually testing is in general indicative of a
missing cleanup. There is no cleanup to be done here, but nonetheless, use
refcount_dec_and_test() as required.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mirroring packets to the CPU port the mirrored packets are trapped
to the CPU. However, unlike other traps, it is not possible to set a
policer on the associated trap group. Instead, the policer needs to be
set on the SPAN agent.
Moreover, the policer ID must be within a specified range: From a
configurable (even) base ID to this base plus the maximum number of SPAN
agents.
While the immediate use case is to set the policer on a SPAN agent that
mirrors to the CPU port, a policer can be set on any SPAN agent.
Therefore, the operation is implemented for all SPAN agent types.
Extend the SPAN agent request API to allow passing the desired policer
ID that should be bound to the SPAN agent. Return an error for
Spectrum-1, as it does not support policer setting on a SPAN agent.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the only parameter of a SPAN agent is the netdev which
the SPAN agent should mirror to.
The next patch will add the ability to request a SPAN agent that mirrors
to a specific netdev and has a specific policer ID bound to it. This is
required when mirroring packets to the CPU port.
Therefore, encapsulate the sole parameter to mlxsw_sp_span_agent_get()
in a structure, so that it could later be extended with policer
information.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum-2 and Spectrum-3 ASICs are able to mirror packets towards
the CPU. These packets are then trapped like any other packet, but with
a special packet trap and additional metadata such as why the packet was
mirrored.
The ability to mirror packets towards the CPU will be utilized by a
subsequent patch set that will mirror packets that were dropped by the
ASIC for various buffer-related reasons, such as tail-drop and
early-drop.
Add mirroring towards the CPU as a new SPAN agent type and re-use the
functions that mirror to a physical port where possible.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the destination netdev to which we mirror must be a valid
netdev. However, this is going to change with the introduction of
mirroring towards the CPU port, as the CPU port does not have a backing
netdev.
Avoid dereferencing the destination netdev when it is not clear if it is
valid or not.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parms_set() callback is supposed to fill in the parameters for the
SPAN agent, such as the destination port and encapsulation info, if any.
When mirroring to the CPU port we cannot resolve the destination port
(the CPU port) without access to the driver private info.
Pass the driver private info to parms_set() callback so that it could be
used later on to resolve the CPU port.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The various SPAN agent types differ in their mirror targets (i.e.,
physical port netdev vs. VLAN netdev) and the encapsulation headers that
they need to encapsulate the mirrored packets with.
The Spectrum-2 and Spectrum-3 ASICs support a SPAN agent type that is
able to mirror towards the CPU, whereas the Spectrum-1 ASIC does not.
Prepare for the addition of this new SPAN agent type by splitting the
SPAN agent operations to be per-ASIC.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the binding of global mirroring triggers to a SPAN agent is
global, packets are only mirrored if they belong to a port and TC on
which the trigger was enabled. This allows, for example, to mirror
packets that were tail-dropped on a specific netdev.
Implement the operations that allow to enable / disable a global
mirroring trigger on a specific port and TC.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global mirroring triggers are triggers that are only keyed by their
trigger, as opposed to per-port triggers, which are keyed by their
trigger and port.
Such triggers allow mirroring packets that were tail/early dropped or
ECN marked to a SPAN agent.
Implement the previously added trigger operations for these global
triggers. Since such triggers are only supported from Spectrum-2
onwards, have the Spectrum-1 operations return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a SPAN agent can only be bound to a per-port trigger where
the trigger is either an incoming packet (INGRESS) or an outgoing packet
(EGRESS) to / from the port.
The subsequent patch will introduce the concept of global mirroring
triggers. The binding / unbinding of global triggers is different than
that of per-port triggers. Such triggers also need to be enabled /
disabled on a per-{port, TC} basis and are only supported from
Spectrum-2 onwards.
Add trigger operations that allow us to abstract these differences. Only
implement the operations for per-port triggers. Next patch will
implement the operations for global triggers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-ASIC SPAN operations are relevant to the SPAN module and
therefore should be implemented there and not in the main driver file.
Move them.
These operations will be extended later on.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second commit cited below performed a cast of 'u32 buffsize' to
'(u16 *)' when calling mlxsw_sp_port_headroom_8x_adjust():
mlxsw_sp_port_headroom_8x_adjust(mlxsw_sp_port, (u16 *) &buffsize);
Colin noted that this will behave differently on big endian
architectures compared to little endian architectures.
Fix this by following Colin's suggestion and have the function accept
and return 'u32' instead of passing the current size by reference.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Fixes: 60833d54d5 ("mlxsw: spectrum: Adjust headroom buffers for 8x ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Suggested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port's headroom buffers are used to store packets while they
traverse the device's pipeline and also to store packets that are egress
mirrored.
On Spectrum-3, ports with eight lanes use two headroom buffers between
which the configured headroom size is split.
In order to prevent packet loss, multiply the calculated headroom size
by two for 8x ports.
Fixes: da382875c6 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the old SPAN API now that matchall-based and flower-based
mirroring were converted to use the new API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, each port whose outgoing traffic is analyzed
needs to have an egress mirror buffer.
The size of the egress mirror buffer is calculated based on various
parameters, two of which are the speed and the MTU of the port.
Therefore, when the MTU or the speed of a port change, the SPAN code is
called to see if the egress mirror buffer of the port needs to be
adjusted.
Currently, this is done by traversing all the SPAN agents and for each
SPAN agent the list of bound ports is traversed.
Instead of the above, traverse the recently added list of analyzed
ports.
This will later allow us to remove the old SPAN API.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a SPAN agent can only be bound to a per-port trigger where
the trigger is either an incoming packet (INGRESS) or an outgoing packet
(EGRESS) to / from the port.
A follow-up patch set will introduce the concept of global triggers and
per-{port, TC} enablement. With global triggers, the trigger entry is
only keyed by a trigger and not by a port and a trigger. The trigger can
be, for example, a packet that was early dropped.
While the binding between the SPAN agent and the trigger is performed
only once, the trigger entry needs to be reference counted, as the
trigger can be enabled on multiple ports.
Add APIs to bind / unbind a SPAN agent to a trigger and reference count
the trigger entry in preparation for global triggers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that adjusts the egress buffer size is not symmetric at the
moment. The update is done via a call to
mlxsw_sp_span_port_buffer_update(), but the disablement is done inline
by invoking the write to SBIB register directly.
Wrap the disablement code in mlxsw_sp_span_port_buffer_disable().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch will introduce mlxsw_sp_span_port_buffer_disable() function
that disables the egress buffer on an analyzed port. Rename the opposite
function that updates the buffer on an analyzed port accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An analyzed port is a port whose incoming / outgoing traffic is mirrored
to a SPAN agent and analyzed on a remote server.
A port can be analyzed by multiple tc filters and therefore the
corresponding analyzed port entry needs to be reference counted. This is
significant because ports whose outgoing traffic is analyzed need to
have an egress mirror buffer.
Add APIs to get / put an analyzed port. Allocate an egress mirror buffer
on a port when it is first inspected at egress and free the buffer when
it is no longer inspected at egress.
Protect the list of analyzed ports with a mutex, as a later patch will
traverse it from a context in which RTNL lock is not held.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given a netdev that packets should be mirrored to, create a SPAN agent
and return its identifier to the caller.
The SPAN agent is reference counted, as multiple tc-mirred actions can
point to the same destination netdev.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to commit e99f8e7f88 ("mlxsw: Replace zero-length
array with flexible-array member"), use a flexible-array member to get a
compiler warning in case the flexible array does not occur last in the
structure.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'refcount_t' is very useful for catching over/under flows. Convert the
SPAN agent objects to use it instead of 'int' for their reference count.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To the best of my knowledge, these debug prints were never used. Remove
them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order not to needlessly schedule the work item that updates the
mirroring agents, only schedule it if there are any mirroring agents
present.
This is done by adding an atomic counter that counts the active
mirroring agents.
It is incremented / decremented whenever a mirroring agent is created /
destroyed. It is read before scheduling the work item and in the
devlink-resource occupancy callback.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch added a work item in the mirroring code that will take
care of updating the active mirroring agents in response to different
events.
Change the mirroring agents update function - mlxsw_sp_span_respin() -
to invoke this work item when called.
Therefore there is no need for callers to schedule a work item
themselves.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver updates its mirroring agents whenever it receives a
notification about an event that can affect these. For example, the
addition of a route might require the driver to change the egress port
of an ERSPAN session.
Currently, RTNL needs to be held when these agents are updates, so the
driver either:
1. Calls directly into the mirroring code, in case RTNL is held
2. Schedules a work item that will take RTNL and call into the mirroring
code
Simplify this by having the mirroring code schedule the work item for
the update instead of requiring callers to schedule a work item
themselves.
The conversion of the callers will be done in the next patch to make
review easier.
This will later allow us to remove RTNL from different parts of the
driver. It will also allow us to only schedule the work item in case
there are active mirroring agents, which is information private to the
mirroring code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate the main mirroring struct and the individual structs for the
different mirroring agents in a single allocation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct holding the different mirroring agents is currently allocated
as part of the main driver struct. This is unlike other driver modules.
Allocate the memory required to store the different mirroring agents as
part of the initialization of the mirroring module.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PUDE event is handled and the link is up, update the port SPAN
buffer size according to the current speed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SPAN egress mirroring buffer size, it is needed to use a different
formula for Spectrum and Spectrum-2. Move the buffer size computation to
ops and implement new formula for Spectrum-2.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid duplication of code that is doing buffsize update and put it into
a separate helper function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports an enhanced switched port analyzer that enables
selecting network traffic for analysis by a network analyzer.
SPAN agents are configured and consumed whenever a tc filter is added
with a mirror action to a new destination. The destination can either be
a physical port (e.g., swp1), a VLAN device or a gretap.
Expose the maximum number of SPAN agents and their current usage to the
user.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an IPv6 gateway to rtable. Since a gateway is either
IPv4 or IPv6, make it a union with rt_gw4 where rt_gw_family decides
which address is in use.
When dumping the route data, encode an ipv6 nexthop using RTA_VIA.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow the gateway to be either an IPv4 or IPv6 address, remove
rt_uses_gateway from rtable and replace with rt_gw_family. If
rt_gw_family is set it implies rt_uses_gateway. Rename rt_gateway
to rt_gw4 to represent the IPv4 version.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current fib_multipath_hash_policy can make hash based on the L3 or
L4. But it only work on the outer IP. So a specific tunnel always
has the same hash value. But a specific tunnel may contain so many
inner connections.
This patch provide a generic multipath_hash in floi_common. It can
make a user-define hash which can mix with L3 or L4 hash.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed the is_gretap_dev and is_ip6gretap_dev logic from structure
comparison to string comparison of the rtnl_link_ops kind field.
This approach aligns with the current identification methods and function
names of vxlan and geneve network devices.
Convert mlxsw to use these helpers and use them in downstream mlx5 patch.
Signed-off-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When offloading mirror-to-gretap, mlxsw needs to preroute the path that
the encapsulated packet will take. That path may include a LAG device
above a front panel port. So far, mlxsw resolved the path to the first
up front panel slave of the LAG interface, but that only reflects
administrative state of the port. It neglects to consider whether the
port actually has a carrier, and what the LACP state is.
So instead of checking upness of the device, check carrier state and
txability.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When offloading mirroring to gretap or ip6gretap netdevices, an 802.1q
bridge is one of the soft devices permissible in the underlay when
resolving the packet path. After the packet path is resolved to a
particular bridge egress device, flags on packet VLAN determine whether
the egressed packet should be tagged.
The current logic however only ever sets the VLAN tag, never suppresses
it. Thus if there's a VLAN netdevice above the bridge that determines
the packet VLAN, that VLAN is never unset, and mirroring is configured
with VLAN tagging.
Fix by setting the packet VLAN on both branches: set to zero (for unset)
when BRIDGE_VLAN_INFO_UNTAGGED, copy the resolved VLAN (e.g. from bridge
PVID) otherwise.
Fixes: 946a11e740 ("mlxsw: spectrum_span: Allow bridge for gretap mirror")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resolving a path that the packet will take after being encapsulated
in mirror-to-gretap scenarios, one of the devices en route could be a
LAG. In that case, mirror to first up slave that corresponds to a front
panel port.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENOENT is suitable when an item is looked for in a collection and can't
be found. The failure here is actually a depletion of a resource, where
ENOBUFS is the more fitting error code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
