GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d269 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace 802.1Q FIDs and VLAN RIFs with their emulated counterparts.
The emulated 802.1Q FIDs are actually 802.1D FIDs and thus use the same
flood tables, of per-FID type. Therefore, add 4K-1 entries to the
per-FID flood tables for the new FIDs and get rid of the FID-offset
flood tables that were used by the old 802.1Q FIDs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Router interfaces (RIFs) constructed on top of VLAN-aware bridges are of
"VLAN" type, whereas RIFs constructed on top of VLAN-unaware bridges of
"FID" type.
In other words, the RIF type is derived from the underlying FID type.
VLAN RIFs are used on top of 802.1Q FIDs, whereas FID RIFs are used on
top of 802.1D FIDs.
Since the previous patch emulated 802.1Q FIDs using 802.1D FIDs, this
patch emulates VLAN RIFs using FID RIFs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a local route that matches the source IP of an offloaded NVE tunnel
is notified, the driver needs to program it to perform NVE decapsulation
instead of merely trapping packets to the CPU.
This patch complements "mlxsw: spectrum_router: Enable local routes
promotion to perform NVE decap" where existing local routes were
promoted to perform NVE decapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, different VRFs (routing tables) are represented using
different virtual routers (VRs) and thus the kernel's table IDs are
mapped to VR IDs.
Allow internal users of the IP router to query the VR ID based on a
kernel table ID.
This is needed - for example - when configuring the underlay VR where
VxLAN encapsulated packets will undergo an L3 lookup. In this case, the
kernel's table ID is derived from the VxLAN device's configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an NVE tunnel with an IP underlay (e.g., VxLAN) is configured the
local route to the tunnel's source IP needs to be promoted to perform
NVE decapsulation.
Expose an API in the unicast IP router to promote / demote local routes.
The case where a local route is configured after the creation of the NVE
tunnel will be handled in a subsequent patch in the set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl setting controls whether packet priority should be updated
after forwarding. Configure RGCR.usp accordingly so that the device is
in sync with the kernel handling.
Note that RGCR doesn't allow changing arbitrary parameters
mid-operation, however "usp" is exempt and can be reconfigured.
Also react to NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE notifications
that signify change in this configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The boilerplate to schedule NETEVENT_IPV4_MPATH_HASH_UPDATE and
NETEVENT_IPV6_MPATH_HASH_UPDATE handling is almost equivalent to that of
NETEVENT_IPV4_FWD_UPDATE_PRIORITY_UPDATE that's coming in the next
patch. The only difference is which actual worker function should be
called. Extract this boilerplate into a named function in order to allow
reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hosts using a VRRP router send their packets with a destination MAC of
the VRRP router which is of the following form [1]:
IPv4 - 00-00-5E-00-01-{VRID}
IPv6 - 00-00-5E-00-02-{VRID}
Where VRID is the ID of the virtual router. Such packets are directed to
the router block in the ASIC by an FDB entry that was added in the
previous patch.
However, in certain cases it is possible to skip this FDB lookup and
send such packets directly to the router. This is accomplished by adding
these special MAC addresses to the RIF cache. If the cache is hit, the
packet will skip the L2 lookup and ingress the router with the RIF
specified in the cache entry.
1. https://tools.ietf.org/html/rfc5798#section-7.3
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IP packet received on a netdev with a macvlan upper whose MAC matches
the packet's destination MAC will be re-injected to the Rx path as if it
was received by the macvlan, and perform an L3 lookup.
Reflect this functionality to the ASIC by programming FDB entries that
will direct MACs of macvlan uppers to the router.
In a similar fashion to router interfaces (RIFs) that are programmed
upon the addition of the first IP address on an interface and destroyed
upon the removal of the last IP address, the FDB entries for the macvlan
are added and destroyed based on the addition of the first and removal
of the last IP address on the macvlan.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow more unicast MAC addresses (e.g., VRRP virtual MAC) to
be directed to the router we need to enable macvlan uppers on top of
mlxsw netdevs.
Allow macvlan upper devices on top of mlxsw netdevs and sanitize
configurations that can't work. For example, a macvlan can't be enslaved
to a bridge as without ACLs the device doesn't take the destination MAC
into account when classifying a packet to a bridge instance (i.e., a
FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the Spectrum-2 KVD linear manager implementation, entry_count will be
needed even for the free function. So pass it down.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future Spectrum-2 KVD linear manager implementation needs to know type
of the entry to alloc and free. So define the types in an enum and
pass it down to alloc and free functions. Once the entry type
is passed down, KVDL common part knows sizes of each entry types,
so replace size function arg with entry count.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, gcc correctly points out
that the 'vid' variable is uninitialized whenever br_vlan_get_pvid
returns an error:
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c: In function 'mlxsw_sp_rif_vlan_fid_get':
drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:6881:6: error: 'vid' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the condition check to always return -EINVAL here,
which I guess is what the author intended here.
Fixes: e6f1960ae6 ("mlxsw: spectrum_router: Allocate FID according to PVID")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetworkManager likes to manage linklocal prefix routes and does so with
the NLM_F_APPEND flag, breaking attempts to simplify the IPv6 route
code and by extension enable multipath routes with device only nexthops.
Revert f34436a430 and these followup patches:
6eba08c362 ("ipv6: Only emit append events for appended routes").
ce45bded64 ("mlxsw: spectrum_router: Align with new route replace logic")
53b562df8c ("mlxsw: spectrum_router: Allow appending to dev-only routes")
Update the fib_tests cases to reflect the old behavior.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: David Ahern <dsahern@gmail.com>
In order to allow querying of the VID for which a RIF was created, add
a new function that returns a FID for a given RIF.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to guard against removal of a PVID for which a FID was
allocated, spectrum_switchdev needs to first determine whether there is
a RIF associated with a given bridge. To that end, publish a preexisting
function mlxsw_sp_rif_find_by_dev().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For bridge netdevices, instead of assuming that the router traffic is on
VLAN 1, look at the bridge PVID.
This patch assumes that the PVID doesn't change after the router
interface is created (i.e. after the IP address is assigned).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the follow-up patch, mlxsw_sp_rif_vlan_fid_get() will be changed in a
way that could fail. Give that function a possibility to explain the
failure through extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34436a430 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route replace logic so that the
first matching route (i.e., same metric) is replaced.
Have mlxsw replace the first matching route as well.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34436a430 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route append logic so that
dev-only routes can be appended and not only gatewayed routes.
Align mlxsw with the new behaviour.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle append for gateway based routes. Dev-only multipath routes will
be handled by a follow on patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently do not perform accounting in the driver and thus can't
reject routes before resources are exceeded.
However, in order to make users aware of the fact that routes are no
longer offloaded we can return an error for routes configured after the
abort mechanism was triggered.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9776d32537 ("net: Move call_fib_rule_notifiers up in
fib_nl_newrule") it is possible to forbid the installation of
unsupported FIB rules.
Have mlxsw return an error for non-default FIB rules in addition to the
existing extack message.
Example:
# ip rule add from 198.51.100.1 table 10
Error: mlxsw_spectrum: FIB rules not supported.
Note that offload is only aborted when non-default FIB rules are already
installed and merely replayed during module initialization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.
Rename only; not functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all code paths referencing a FIB entry from
rt6_info to fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce fib6_nh structure and move nexthop related data from
rt6_info and rt6_info.dst to fib6_nh. References to dev, gateway or
lwtstate from a FIB lookup perspective are converted to use fib6_nh;
datapath references to dst version are left as is.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Following previous patches driver is ready to handle notifications
arriving from ip6mr - start processing those when they arrive following
the same manner ipmr currently goes through.
This should enable driver to start offloading ipv6 multicast routes.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spectrum_router and spectrum_mr have several APIs that are used to
manipulate configurations originating from ipmr fib notifications.
Following previous patches all the protocol-specifics that are necessary
for the configuration are hidden within spectrum_mr. This allows us to
clean the API and make sure that other than choosing the mr_table based
on the fib notification family, spectrum_router wouldn't care about the
source of the notification when passing it onward to spectrum_mr.
This would later allow us to leverage the same code for fib
notifications originating from ip6mr.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A step toward offloading IPv6 routing, this adds an additional
multicast routing table meant for IPv6 [with its underlying TCAM
region] and populates the default rule for IPv6 multicast packets.
Following this, ingress IPv6 multicast packets would be trapped and
delivered to the host CPU.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ipmr and ip6mr are using the same mr_mfc struct at their core, we
can now refactor the ipmr_cache_{hold,put} logic and apply refcounting
to both ipmr and ip6mr.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like vif notifications, move the notifier struct for MFC as well as its
helpers into a common file; Currently they're only used by ipmr.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update MTU of overlay loopback in accordance with the setting on the
tunnel netdevice.
Fixes: 0063587d35 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the function so that it can be called without forward declaration
from a function that will be added in a follow-up patch.
Fixes: 0063587d35 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to abstract away access to the
ipv6.sysctl.multipath_hash_policy variable, which is not available on
systems compiled without IPv6 support, introduce a wrapper function
ip6_multipath_hash_policy() that falls back to 0 on non-IPv6 systems.
Use this wrapper from mlxsw/spectrum_router instead of a direct
reference.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to 28678f07f1 ("mlxsw: spectrum_router: Update multipath hash
parameters upon netevents") for IPv4, make sure the kernel and asic are
using the same hash algorithm for path selection.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename NETEVENT_MULTIPATH_HASH_UPDATE to
NETEVENT_IPV4_MPATH_HASH_UPDATE to denote it relates to a change
in the IPv4 hash policy.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some netdevices, for which mlxsw offloads mirroring, may have a
complex relationship between the declared intent and low-level
device configuration.
Trying to accurately track which changes might influence offloading
decisions is finicky and error-prone. Instead, this patch introduces a
function mlxsw_sp_span_entry_respin, which re-queries the configuration
anew and, if different, removes the existing offloads and installs new
ones.
Call this function strategically at event handlers that might influence
the mirroring configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mlxsw replaces (or deletes) a route it removes the offload
indication from the replaced route. This is problematic for IPv4 routes,
as the offload indication is stored in the fib_info which is usually
shared between multiple routes.
Instead of unconditionally clearing the offload indication, only clear
it if no other route is using the fib_info.
Fixes: 3984d1a89f ("mlxsw: spectrum_router: Provide offload indication using nexthop flags")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NL_SET_ERR_MSG_MOD helper which adds the module name instead
of specifying the prefix each time.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ip_tunnel_parm, where GRE and several other tunnel types hold
information, is IPv4-specific. The current router / ipip code in mlxsw
however uses it as if it were generic.
Make it clear that it's not. Rename many functions from _params_ to
_params4_. mlxsw_sp_ipip_parms_saddr() and _daddr() take a proto
argument to dispatch on it. Move the dispatch logic to
mlxsw_sp_ipip_netdev_saddr() and _daddr(), and replace with
single-protocol functions.
In struct mlxsw_sp_ipip_entry, move the "parms" field to a (for the time
being, singleton) union. Update users throughout.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mlxsw_sp_fib_create() and mlxsw_sp_mr_table_create()
use ERR_PTR macro to propagate int err through return of a pointer,
the return value is not NULL in case of failure. So if one
of the calls fails, one of vr->fib4, vr->fib6 or vr->mr4_table
is not NULL and mlxsw_sp_vr_is_used wrongly assumes
that vr is in use which leads to crash like following one:
[ 1293.949291] BUG: unable to handle kernel NULL pointer dereference at 00000000000006c9
[ 1293.952729] IP: mlxsw_sp_mr_table_flush+0x15/0x70 [mlxsw_spectrum]
Fix this by using local variables to hold the pointers and set vr->*
only in case everything went fine.
Fixes: 76610ebbde ("mlxsw: spectrum_router: Refactor virtual router handling")
Fixes: a3d9bc506d ("mlxsw: spectrum_router: Extend virtual routers with IPv6 support")
Fixes: d42b0965b1 ("mlxsw: spectrum_router: Add multicast routes notification handling functionality")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.
Simply remove the error message and gracefully accept such events.
Fixes: c723c735fa ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes: 60f040ca11 ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I tried to make sure only used prefix lengths are
present in the LPM tree shared between all virtual routers.
However, this optimization had to be removed in commit a69518cf0b
("mlxsw: spectrum_router: Avoid expensive lookup during route removal"),
since determining the used prefix lengths required us to traverse all
the active virtual routers, which could result in a hung task depending
on the number of VRFs and whether routes were removed due to abort or
not.
Re-introduce the optimization by moving the prefix usage accounting from
the virtual routers to the LPM tree, as this accounting is only used in
order to determine the tree's structure.
To make the sharing of the trees more explicit, the two trees (for IPv4
and IPv6) are stored in the shared router struct and upon the creation
of a virtual router it is immediately bound to both.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
