If a flash chip has more than 16MB capacity but its BFPT reports
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, the spi-nor framework defaults to 3.
The check in spi_nor_set_addr_width() doesn't catch it because addr_width
did get set. This fixes that check.
Fixes: f9acd7fa80 ("mtd: spi-nor: sfdp: default to addr_width of 3 for configurable widths")
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20201006132346.12652-1-bert@biot.com
This reverts commit 03edda0e1e.
This leads to warn dump like [1] on some platforms and reorders MTD
devices which may break user space expectations [2]. So revert the change.
[1]:
[ 1.849801] ------------[ cut here ]------------
[ 1.854271] mscc_felix 0000:00:00.5: device is disabled, skipping
[ 1.858753] WARNING: CPU: 1 PID: 7 at kernel/kmod.c:136 __request_module+0x3a4/0x568
[...]
[2] Bug report: https://lore.kernel.org/linux-mtd/20201003150633.23416-1-michael@walle.cc/
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201005090321.8724-1-vigneshr@ti.com
Add support Winbond w25q{64,128,256}jwm which are identical to existing
w25q32jwm except for their sizes.
This was tested with w25q64jwm, basic erase/write/readback and
lock/unlock both lower/upper blocks were okay.
Signed-off-by: ikjn@chromium.org <ikjn@chromium.org>
Signed-off-by: Xingyu Wu <wuxy@bitland.corp-partner.google.com>
Signed-off-by: ST Lin <stlin2@winbond.com>
Tested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200928060631.2090541-1-ikjn@chromium.org
Intel Alder Lake-S has the same SPI serial flash controller as Cannon
Lake. Add Alder Lake-S PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200925095109.51148-1-mika.westerberg@linux.intel.com
On my system the spi_nor_probe() took ~6 ms at bootup. That's not a
lot, but every little bit adds up to a slow bootup. While we can get
this out of the boot path by making it a module, there are times where
it is convenient (or even required) for this to be builtin the kernel.
Let's set that we prefer async probe so that we don't block other
drivers from probing while we are probing.
This is a tiny little change that is almost guaranteed to be safe for
anything that is able to run as a module, which SPI_NOR is.
Specifically modules are already probed asynchronously. Also: since
other things in the system may have enabled asynchronous probe the
system may already be doing other things during our probe.
There is a small possibility that some other driver that was a client
of SPI_NOR didn't handle -EPROBE_DEFER and was relying on probe
ordering and only worked when the SPI_NOR and the SPI bus were
builtin. In that case the other driver has a bug that's waiting to
hit and the other driver should be fixed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200902160002.1.I658d1c0db9adfeb9a59bc55e96a19e192c959e55@changeid
As the only user has been removed in previous patch, let's revert
this one together.
This reverts commit be192209d5.
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-2-git-send-email-yangyicong@hisilicon.com
Previous patch intends to restore the flash's QE bit when removed/shutdown,
but may have some problems and break the flash:
- for those originally in Quad mode, this patch will clear the QE bit
when unloaded the flash, which is incorrect.
- even with above problem solved, it may still break the flash as some
flash's QE bit is non-volatile and lots of set/reset will wear out
the bit.
- the restore method cannot be proved to be valid as if a hard
reset or accident crash happened, the spi_nor_restore() won't be
performed the the QE bit will not be restored as we expected to.
So let's revert it to fix this. The discussion can be found at [1].
This reverts commit cc59e6bb6c.
[1] https://lore.kernel.org/linux-mtd/CAO8h3eFLVLRmw7u+rurKsg7=Nh2q-HVq-HgVXig8gf5Dffk8MA@mail.gmail.com/
Reported-by: Matthias Weisser <m.weisser.m@gmail.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/1599205640-26690-1-git-send-email-yangyicong@hisilicon.com
Both w25q64 and s25fl064k nor flash support QUAD and DUAL read
command, hence update the same in flash_info table.
This is tested on Broadcom Stingray SoC (bcm958742t).
s25fl064k and w25q64 share the same JEDEC ID. The search alg will
return the first hit, so s25fl064k even for the winbond parts. We
should differentiate between these flashes, but it's not in the
scope of this patch. Related discussion at:
Link: https://lore.kernel.org/patchwork/patch/628090/
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200529071655.739-1-rayagonda.kokatanur@broadcom.com
[tudor.ambarus@microchip.com: Update commit message and indicate that
s25fl064k and w25q64 share the same JEDEC ID]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Micron mt25qu02g supports both x2 and x4 transactions. Add the
SPI_NOR_DUAL_READ flag to its spi_nor_ids[] table entry.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-3-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Macronix mx66u2g45g is a 1.8V, 2Gbit (256MB) device that
supports x1, x2, or x4 operation.
Tested on Pensando SoC hardware with a cadence quadspi controller
via drivers/spi/spi-cadence-quadspi.c, in x2 mode at 50MHz.
- random data write, erase, read - verified erase operations
- random data write, read/compare - verified write/read operations
Signed-off-by: David Clear <dac2@pensando.io>
Acked-by: Shannon Nelson <snelson@pensando.io>
Link: https://lore.kernel.org/r/20200720163656.38006-2-dac2@pensando.io
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
After spi_nor_write_disable() return code checks were introduced in the
spi-nor front end intel-spi backend stopped to work because WRDI was never
supported and always failed.
Just pretend it was sucessful and ignore the command itself. HW sequencer
shall do the right thing automatically, while with SW sequencer we cannot
do it anyway, because the only tool we had was preopcode and it makes no
sense for WRDI.
Fixes: bce679e5ae ("mtd: spi-nor: Check for errors after each Register Operation")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/282e1305-fd08-e446-1a22-eb4dff78cfb4@nokia.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
If the flash's quad mode is enabled, it'll remain in the quad mode when
it's removed. If we drive the flash next time in Standard/Dual SPI mode,
the QE bit is not cleared and the function of flash's WP# and RESET#/HOLD#
have been switched to IO2 and IO3 and are not restored.
Disable the Quad mode in spi_nor_restore(), then the flash's QE bit will
be cleared when removed. This will make sure the flash always enter the
Standard/Dual SPI mode when loaded.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-3-git-send-email-yangyicong@hisilicon.com
Previous we didn't provide a way to disable the flash's quad mode.
Which means we cannot do some cleanup works when to remove or
poweroff the flash, like what set 4-byte address mode does in
spi_nor_restore().
Add the capability to disable the flash quad mode, by introducing
an enable flag in the flash parameters quad_enable() hooks and
related functions.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1594027356-19088-2-git-send-email-yangyicong@hisilicon.com
The s70fl01gs is a dual die stack of two s25fl512s die with dedicated chip
select pins to each. Tested with the device and confirmed that is working
as two s25fl512s devices. The current device ID in the flash_info table
matches with s70fs01gs which does not work with current MTD (s70fs01gs
does not support RDSR(05h) which is critical for erase/write).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200626051650.495-1-Takahiro.Kuwano@cypress.com
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing and let flashes set it in
their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200623183030.26591-12-p.yadav@ti.com
This chip is (nearly) identical to the Winbond w25q64 which is
already supported by Linux. Compared to the w25q64, the 'jvm'
has a different JEDEC ID.
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
[tudor.ambarus@microchip.com: Order entry alphabetically, update
subject, update Sven's email address]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200629195306.1030-1-TheSven73@gmail.com
The MX25R1635F is the smaller sibling of the MX25R3235F that is
already supported. It's only half the size (16Mb).
It was tested on the Kontron Electronics i.MX8MM SoM (N8010)
using raw read and write from and to the mtd device and
the 'flash_erase' command.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[tudor.ambarus@microchip.com: update subject]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200702140523.6811-1-frieder.schrempf@kontron.de
Intel Tiger Lake-H has the same SPI serial flash controller as Cannon
Lake. Add Tiger Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200624192103.78770-1-mika.westerberg@linux.intel.com
Intel Emmitsburg has the same SPI serial flash controller as Lewisburg.
Add Emmitsburg PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200615155748.920-1-mika.westerberg@linux.intel.com
Now that cadence-quadspi has been converted to use spi-mem framework,
move it under drivers/spi/
Update license header to match SPI subsystem style
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-9-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move cadence-quadspi driver to use spi-mem framework. This is required
to make the driver support for SPI NAND flashes in future.
Driver is feature compliant with existing SPI NOR version.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-8-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop redundant WREN command in cqspi_erase() as SPI NOR core takes care
of sending WREN command before sending erase command.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-7-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_chan_by_mask() can throw EPROBE_DEFER if DMA provider
is not yet probed. Currently driver just falls back to using PIO mode
(which is less efficient) in this case. Instead return probe deferral
error as is so that driver will be re probed once DMA provider is
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-6-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to undo the prior changes done by the driver when exiting due
to failure to acquire reset lines.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-5-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If driver fails to acquire DMA channel then don't initialize
rx_dma_complete struct as it won't be used.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-4-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently direct access mode is used on platforms that have AHB window
(memory mapped window) larger than flash size. This feature is limited
to TI platforms as non TI platforms have < 1MB of AHB window.
Therefore introduce a driver quirk to disable DAC mode and set it for
non TI compatibles. This is in preparation to move to spi-mem framework
where flash geometry cannot be known.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop configuration of Flash size, erase size and page size
configuration. Flash size is needed only if using AHB decoder (BIT 23 of
CONFIG_REG) which is not used by the driver.
Erase size and page size are needed if IP is configured to send WREN
automatically. But since SPI NOR layer takes care of sending WREN, there
is no need to configure these fields either.
Therefore drop these in preparation to move the driver to spi-mem
framework where flash geometry is not visible to controller driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are 2 different chips (w25q256fv and w25q256jv) that share
the same JEDEC ID. Only w25q256jv fully supports 4-byte opcodes.
Use SFDP header version to differentiate between them.
Fixes: 10050a02f7 ("mtd: spi-nor: Add 4B_OPCODES flag to w25q256")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Despite of how spi_nor_parse_bfpt() abuses the structure fields during
their calculation, gcc manages to make some decent code out of that. :-)
Yet adding a local variable to store the BFPT DWORDs during calculations
still saves 12 bytes of the object code (AArch64 gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
JESD216 rev D makes BFPT 20 DWORDs. Update the BFPT size define to
reflect that.
The check for rev A or later compared the BFPT header length with the
maximum BFPT length, BFPT_DWORD_MAX. Since BFPT_DWORD_MAX was 16, and so
was the BFPT length for both rev A and B, this check worked fine. But
now, since BFPT_DWORD_MAX is 20, it means this check will also stop BFPT
parsing for rev A or B, since their length is 16.
So, instead check for BFPT_DWORD_MAX_JESD216 to stop BFPT parsing for
the first JESD216 version, and check for BFPT_DWORD_MAX_JESD216B for the
next two versions.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
JESD216D.01 says that when the address width can be 3 or 4, it defaults
to 3 and enters 4-byte mode when given the appropriate command. So, when
we see a configurable width, default to 3 and let flash that default to
4 change it in a post-bfpt fixup.
This fixes SMPT parsing for flashes with configurable address width. If
the SMPT descriptor advertises variable address width, we use
nor->addr_width as the address width. But since it was not set to any
value from the SFDP table, the read command uses an address width of 0,
resulting in an incorrect read being issued.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Cypress cy15b104q and cy15v104q are 4Mbit serial SPI F-RAM devices.
Add support for them to the spi-nor driver.
The actual Device ID of this chip is 7f 7f 7f 7f 7f 7f c2 2c 04. That is
six times the continuation code 7f followed by c2 for Ramtron.
Unfortunately the chip sends the Device ID in reversed order, so the
continuation code is not at the beginning, but instead at the end. Even
more unfortunate is that when reading further the chip sends more 7f
codes which means we are not even able to count the continuation codes.
We can only hope that this reversed Device ID will never match any other
devices ID.
Collisions are improbable as of now, the solution from above is good
enough. In case of future collisions one can introduce an INFO9 macro,
with the downsize that struct flash_info would grow and we have lots of
flashes. A more elegant solution would be to introduce dedicated
flash ID tables for each bank in JESP106BA.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[tudor.ambarus@microchip.com: amend commit description with possible
future solutions in case collisions occur.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The correct terminology is serial NOR flash or SPI NOR.
s/SPI-NOR/SPI NOR and s/spi-nor/SPI NOR across the subsystem.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
s25fs256s was identified as s25fl256s. Differentiate between them by
the Family ID using the INFO6 macro.
Fixes: b199489d37 ("mtd: spi-nor: add the framework for SPI NOR")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Add support for Cypress s25fs128s1 flash. Previously the flash is
decoded as s25fl129p1 by mistake.
Add it in the flash info list to correctly decode. The flash also
needs a fixup for s25fs-s family. Further capability of the flash will
be parsed from bfpt.
The flash has been tested under SPI/DUAL/QUAD mode on hisi-sfc-v3xx
controller, all the write/read/erase works well.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Spansion S25FS-S family has an issue in the Basic Flash Parameter Table
(BFPT): Dword-11 bits 7:4 specify a page size of 512 bytes. Actually
this is configurable in the vendor unique register (CR3V) and even the
factory default setting is to "wrap at 256 bytes", so blindly relying
on BFPT breaks the page writes on these chips. Add the post-BFPT fixup
which restores the default page size of 256 bytes -- to properly read
CR3V this early is quite intrusive and should better be done as a new
feature; Alexander Sverdlin had the patch doing that:
https://patchwork.ozlabs.org/project/linux-mtd/patch/20200227123657.26030-1-alexander.sverdlin@nokia.com/
Fixes: dfd2b74530 ("mtd: spi-nor: add Spansion S25FS512S ID")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The functions return 1 if ready, 0 if not ready, -errno on errors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_ready() returns 1 if ready, 0 if not ready and -errno on errors.
Do the same in all the spi_nor_*_ready() children.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
n25q00 uses the 4 bit Block Protection scheme and supports Top/Bottom
protection via the BP and TB bits of the Status Register.
Enable locking for n25q00. Tested with cirrus controller.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mx25u51245g is a mass production for new design and
replace mx66u51235f(phase out).
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mx25l51245g is a mass production for new design and
replace mx66l51235l(phase out).
Validated by read, erase, read back, write and read back
on Xilinx Zynq PicoZed FPGA board which included
Macronix SPI Host (driver/spi/spi-mxic.c).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When spi_nor_info_init_params(), spi_nor_sfdp_init_params(), and
spi_nor_init_params() were added, the kernel-doc for them contained
a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix them.
Fixes: 1c1d8d98e1 ("mtd: spi-nor: Split spi_nor_init_params()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When spi_nor_manufacturer_init_params() was added, the kernel-doc for it
contained a typo: 'struct spi-nor' instead of 'struct spi_nor' -- fix it.
Fixes: ce0b6f3f3c ("mtd: spi-nor: Add default_init() hook to tweak flash parameters")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
As 4bit block protection patchset for some micron models are merged,
n25q128a11 also uses 4 bit Block Protection scheme, so enable locking
for it. Tested it on n25q128a11, the locking functions work well.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Jungseung Lee <js07.lee@samsung.com>
Tested-by: Shreyas Joshi <shreyasjoshi15@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry. Tested with the device and
confirmed that is working.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@cypress.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Commit a0900d0195 ("mtd: spi-nor: Prepare core / manufacturer code
split") moved various files into a new directory, but did not add the new
directory to its parent directory Makefile. The moved files no longer
build, and affected flash chips no longer instantiate.
Adding the new directory to the parent directory Makefile fixes the
problem.
Fixes: a0900d0195 ("mtd: spi-nor: Prepare core / manufacturer code split")
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Use Joe Perches cvt_fallthrough.pl script to convert
/* fallthrough */
comments (and its derivatives) into a
fallthrough;
statement. This automatically drops useless ones.
Do it MTD-wide.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20200325212115.14170-1-miquel.raynal@bootlin.com
n25q512ax3 and n25q512a use the 4 bit Block Protection scheme.
Enable locking for both. Tested on n25q512ax3. The other is modified
following the datasheet.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Currently we are supporting block protection only for flash chips with
3 block protection bits (BP0-2) in the SR register.
Enable block protection support for flashes with 4 block protection bits
(BP0-3).
Add a flash_info flag for flashes that describe 4 block protection bits.
Add another flash_info flag for flashes in which BP3 bit is not adjacent
to the BP0-2 bits.
Tested with a n25q512ax3 (BP0-3) and w25q128 (BP0-2).
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The current mainline locking was restricted and could only be applied
to flashes that have 3 block protection bits and fixed locking ratio.
A new method of normalization was reached at the end of the discussion [1].
(1) - if bp slot is insufficient.
(2) - if bp slot is sufficient.
if (bp_slots_needed > bp_slots) // (1)
min_prot_length = sector_size << (bp_slots_needed - bp_slots);
else // (2)
min_prot_length = sector_size;
This patch changes logic to handle block protection based on min_prot_length.
It is suitable for the overall flashes with exception of some corner cases
(see EON and catalyst) and easy to extend and apply for the case of 2bit or
4bit block protection.
[1] http://lists.infradead.org/pipermail/linux-mtd/2020-February/093934.html
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When there are more BP settings than needed for defining the protected
areas of the flash memory, most flashes will define the remaining
settings as "protect all", i.e. the equivalent of having all the BP bits
set to one. But there are flashes where the in-between BP values
are undefined (not mentioned), and only the "all bits set" is protecting
the entire memory. One such example is w25q80, where BP[2:0]=0b101 and
0b110 are not defined.
Set all the BP bits to one when lock_len == mtd->size, to treat this
special case.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When an Erase or Program error occurs on a spansion/cypress or a
micron flash, the WEL bit remains set to one and should be cleared
with a WRDI command in order to protect against inadvertent writes
that can possible corrupt the contents of the memory.
Winbond, macronix, gd, etc., do not support the E_ERR and P_ERR bits in the
Status Register and always clear the WEL bit regardless of the outcome
of the erase or page program operation (ex w25q40bw, MX25L25635E).
Issue a WRDI command when erase or page program errors occur.
Reported-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
The SPI NOR controllers drivers must not be able to use structures that
are meant just for the SPI NOR core.
struct spi_nor_flash_parameter is filled at run-time with info gathered
from flash_info, manufacturer and sfdp data. struct spi_nor_flash_parameter
should be opaque to the SPI NOR controller drivers, make sure it is.
spi_nor_option_flags, spi_nor_read_command, spi_nor_pp_command,
spi_nor_read_command_index and spi_nor_pp_command_index are defined for the
core use, make sure they are opaque to the SPI NOR controller drivers.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Cross manufacturer code is unlikely and discouraged, get rid of the
MFR definitions.
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
All entries have been moved to manufacturer drivers. Get rid of this
empty table.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Create a SPI NOR manufacturer driver for XMC chips, and move the
XMC definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Xilinx chips, and move the
Xilinx definitions outside of core.c.
While at it, remove the SPI_S3AN flag which is now useless.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Catalyst chips, and move the
Catalyst definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Winbond chips, and move the
Winbond definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for SST chips, and move the
SST definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Spansion chips, and move the
Spansion definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Micron/ST chips, and move the
Micron/ST definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Macronix chips, and move the
Macronix definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Xiang Chen <chenxiang66@hisilicon.com>
Create a SPI NOR manufacturer driver for ISSI chips, and move the
ISSI definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Intel chips, and move the
Intel definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Create a SPI NOR manufacturer driver for GigaDevice chips, and move the
GigaDevice definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Fujitsu chips, and move the
Fujitsu definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Everspin chips, and move the
Everspin definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for ESMT chips, and move the
ESMT definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Eon chips, and move the
Eon definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Create a SPI NOR manufacturer driver for Atmel chips, and move the
Atmel definitions outside of core.c.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Declare a spi_nor_manufacturer struct and add basic building blocks to
move manufacturer specific code outside of the core.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Expose the flash_info struct and some function prototypes that
will be used by manufacturers.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
It makes the core file a bit smaller and provides better separation
between the SFDP parsing and core logic.
Keep the core.h and sfdp.h definitions private in drivers/mtd/spi-nor/.
Both expose just the definitions that are required by the core and
manufacturer drivers. None of the SPI NOR controller drivers should
include them.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Move all SPI NOR controller drivers to a controllers/ sub-directory
so that we only have SPI NOR related source files under
drivers/mtd/spi-nor/.
Rename spi-nor.c into core.c, we are about to split this file in multiple
source files (one per manufacturer, plus one for the SFDP parsing logic).
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Rename (*set_4byte)() to (*set_4byte_addr_mode)() for a better
differentiation between the 4 byte address mode and opcodes.
Rename macronix_set_4byte() to spi_nor_set_4byte_addr_mode(), it will be
the only 4 byte address mode method exposed to the manufacturer drivers.
Here's how the manufacturers enter and exit the 4 byte address mode:
- eon, gidadevice, issi, macronix, xmc use EN4B/EX4B
- micron-st needs WEN. st_micron_set_4byte_addr_mode() will become
a private method, as they are the only ones that need WEN before the
EN4B/EX4B commands.
- newer spansion have a 4BAM opcode (this translates to a new, public
command). Older spansion flashes use the BRWR command (legacy in
core.c -> spansion_set_4byte_addr_mode())
- winbond's method is hackish and may be reason for just a flash
fixup hook -> private method
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Replace the manufacturer prefix by something describing more precisely
what those functions do.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
[tudor.ambarus@microchip.com: prepend spi_nor_ to all modified methods.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5pQmYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D9sB/9PBy5hYIWLJOqP3Tegy+si7eEjgYQe
32DvHZRYYL+Oc8OQMGnJYUY5grfriS300TjxeB4MNx8ajVyuaH7e2aIhgTz3oJ6a
YrygFcxEi0LmRT82HyLVxptyblMSo3A8QWOTOqe1aFvJRZjDDKvEIcGCW2RPmtxT
r/EoVVkSv4X+k3GUtYnRBrq12hL+vr1YIjZM05MVu2sDtFXLO2+wotFIODDv15zi
ByBtwhKumKawUOETzGDw4EDV5MJx9nZtswRC4x3hDrLS6au39F/MyP78gpHm8vw+
YfiS5/39rkB6j1QltcP3B9n7joxrgaFAYsLBTZUoE3IjeVTggcKCOSVX
=q5ml
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl5rqKYACgkQS1VPR6WN
FOltQggAvmX8EZO9DvpKr6rVhrapDgkJUT5QmwTwZfmBgp5vlRqd8AvY2IYx6/a8
yVr8TwvbJuvPKaC3PI6I9/feDYx2P5NA9fAoqy6bMACeAwuXcDwjnv/aJo74bf6d
cY2zm/heVXJ9qecPmf0msgxBpnKBaxO/u9JmyX197pHdz3vAqNq2t4w4npSqnUlJ
M/dtUxL8bIjkPeQfbV3F+2y6Ttu5hsGauy5y+spnMnMga4+tTxtokauyPBxvkllv
tqbXP5Q1C0ogByJ0rg1M7XqLb1IuCNzYo5aH20T98aCxmcUyTVnanAMX9J/rmbH8
7ykpSUYMP5WvbpRUqdIWvhmJtkPbSA==
=mMmy
-----END PGP SIGNATURE-----
Merge tag 'mtk-mtd-spi-move' into spi-nor/next
spi: Rewrite mtk-quadspi spi-nor driver with spi-mem
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
The mtk-quadspi driver is replaced by the new spi-mtk-nor driver.
Merge it in spi-nor/next to avoid conflicts during the release cycle.
This driver is superseded by the new spi-mtk-nor driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200306085052.28258-5-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Don't use `tmp` for two purposes (return value, loop counter).
Instead, use `i` for the loop counter, and `ret` for the return value.
- Don't use tabs between type and name in variable declarations,
for consistency with other functions in spi-nor.c.
- Rewrite nested `if`s as `if (a && b)`.
- Remove `info` variable, and use spi_nor_ids[i] directly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
[tudor.ambarus@microchip.com: change i's type from int to unsigned int,
reorder local variables]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Based on the original patch by Boris Brezillon
<boris.brezillon@bootlin.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_spimem_xfer_data() being a helper function for the data reads/
writes contains 3 fragments that depend on the data direction; and I'm
going to add another one to call the SPI dirmap API...
I think this function should be split so that the common fragments are
put into 2 functions, spi_nor_spimem_bounce() and spi_nor_spimem_exec_op()
called from spi_nor_spimem_{read|write}_data(), and the data direction
dependent bits moved back into those read/write functions -- that way we
would be able to avoid *goto*s otherwise needed in the next patch adding
the SPI dirmap support...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The shift variable of SR_BP is conclusive because the first bit of SR_BP
is fixed on all known flashes. Replace ffs operation with SR_BP_SHIFT.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The driver calls le32_to_cpu() to convert the little-endian tables
to a CPU endianness, where le32_to_cpus() should have been called.
Was going to use that one... and then discovered a whole array
converter, le32_to_cpu_array()! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
* block2mtd: page index should use pgoff_t
* maps: physmap: minimal Runtime PM support
* maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
* concat: Fix a comment referring to an unknown symbol
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Cadence: add unspecified HAS_IOMEM dependency
* Various cleanup.
Onenand
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl4zMfgACgkQJWrqGEe9
VoS0xwf+KdaihRno4SkDovcHoF7K54N6CqBhwuV9uabfy4phEr38cyvaivYu0rG7
k/n3CUNRDghTh7DAUT7pBsjUeZn9XxvKyQaZz34TBgoQYwGz57ssp8lMRmJkYoA6
t9z95N9bRJ+IzZJlYELCbhNq+aOGyWYgWL+aaO0CE8OyOeWzdZumdd4k7cF7rSAu
9gWV/6iX/qP081NexfjPEVmMtNQ+0p4T7zQ01nQA7rIZiVoIgMKwBu41aRYycEEs
LeuV5gNEDn2vGBl+u85w5oF6o1TIzDeTmh0G7Jm3NQGGco2kOOZ1O39a0hrDONrA
hEoEIG/rAMKOtaLr6rCGnV/5/i/Tlw==
=WC+m
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core
- block2mtd: page index should use pgoff_t
- maps: physmap: minimal Runtime PM support
- maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
- concat: Fix a comment referring to an unknown symbol
Raw NAND:
- Macronix: Use match_string() helper
- Atmel: switch to using devm_fwnode_gpiod_get()
- Denali: rework the SKIP_BYTES feature and add reset controlling
- Brcmnand: set appropriate DMA mask
- Cadence: add unspecified HAS_IOMEM dependency
- Various cleanup.
Onenand:
- Rename Samsung and Omap2 drivers to avoid possible build warnings
- Enable compile testing
- Various build issues
- Kconfig cleanup
SPI-NAND:
- Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes"
* tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: concat: Fix a comment referring to an unknown symbol
mtd: rawnand: add unspecified HAS_IOMEM dependency
mtd: block2mtd: page index should use pgoff_t
mtd: maps: physmap: Add minimal Runtime PM support
mtd: maps: pcmciamtd: fix possible sleep-in-atomic-context bugs in pcmciamtd_set_vpp()
mtd: onenand: Rename omap2 driver to avoid a build warning
mtd: onenand: Use a better name for samsung driver
mtd: rawnand: atmel: switch to using devm_fwnode_gpiod_get()
mtd: spinand: add support for Toshiba TC58CVG2S0HRAIJ
mtd: rawnand: macronix: Use match_string() helper to simplify the code
mtd: sharpslpart: Fix unsigned comparison to zero
mtd: onenand: Enable compile testing of OMAP and Samsung drivers
mtd: onenand: samsung: Fix printing format for size_t on 64-bit
mtd: onenand: samsung: Fix pointer cast -Wpointer-to-int-cast warnings on 64 bit
mtd: rawnand: denali: remove hard-coded DENALI_DEFAULT_OOB_SKIP_BYTES
mtd: rawnand: denali_dt: add reset controlling
dt-bindings: mtd: denali_dt: document reset property
mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
mtd: rawnand: denali_dt: error out if platform has no associated data
mtd: rawnand: brcmnand: Set appropriate DMA mask
...
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl4nSy0ACgkQJWrqGEe9
VoSr1gf+KKMtE8GabWYbKsgKRx1cmC/0pvRmp7wqjul4gd/s+llKzEDG/qMYUOua
PgynNJeP7LPIZJWqo8TjXZcNxs1E0JSoAjYK58Hm9MOIwiwmdSE7GOVxv8/1drN/
7mjJvnGznol/2GD3U4NRvW/SZHkj0/Xt9Ys70qdpcWDQWJSIUIhrNuKOMgjTP+kp
XfZ4vWL6T9LHJiIojLTkrfjXH774dWflSj8bySz+9d9kwkbvKEGU6zb6sKfGO4nm
yYqQhpUrbN8c4t+hSuJlf140haVhwCIQeujUNlTn2oDXnJIO/98k0jDSn6dpUSdx
H6NvWMa8e8Bz7HAbB7/VOawtjt/k+w==
=UPI6
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.6' into mtd/next
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
This was tested in single, dual and quad mode on a custom board with the
NXP FlexSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add support for the Winbond W25Q32JW-xM flashes. These have a
programmable QE bit. There is also the W25Q32JW-xQ variant which shares
the ID with the W25Q32DW and W25Q32FW parts. The W25Q32JW-xQ has the QE
bit hard strapped to 1, thus don't support the /HOLD and /WP pins.
This was tested in single, dual and quad mode on a custom board with the
NXP FlexSPI controller. Also the BP bits as well as the TB bit were
tested.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The commit 7b678c69c0 ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0 ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc38 ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ops aren't used in any SPI NOR controller. Therefore, remove them
altogether.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Comet Lake-V has the same SPI serial flash controller as Kaby
Lake. Add Comet Lake-V PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The driver is for the HiSilicon FMC (Flash Memory Controller), which
supports SPI NOR in addition other memory technologies, like SPI NAND.
Indeed, the naming in the driver is a little inappropriate, especially
considering that there is already another HiSilicon SPI NOR flash
controller (which I believe the FMC is derived from).
Since we now want to provide software support for this other HiSilicon
controller, update code comments to at least try to make it clear that
this driver is for the FMC.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Adds support for sst26vf016b, a smaller variant of the sst26vf064b.
Tested on a sama5d3 SOC using the atmel,at91rm9200-spi controller.
The dual read could not be tested.
SPI_NOR_QUAD_READ is not added because it requires that the IOC bit
from the Configuration Register to be set to 1, which is not the case:
its default value at power-up is zero and we don't set it to one in
spi-nor either.
Signed-off-by: Joseph Kust <joseph.kust@rockwellcollins.com>
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
[tudor.ambarus@microchip.com: Drop quad read flag, amend commit description]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Micron flashes do not support 16 bit writes on the Status Register.
According to micron datasheets, when using the Write Status Register
(01h) command, the chip select should be driven LOW and held LOW until
the eighth bit of the last data byte has been latched in, after which
it must be driven HIGH. If CS is not driven HIGH, the command is not
executed, flag status register error bits are not set, and the write enable
latch remains set to 1. This fixes the lock operations on micron flashes.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39d1e3340c ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
The chip has 4MB of total capacity, divided into a total of 64 sectors,
each 64KB sized. The chip also supports 4KB large sectors.
Additionally, it supports dual and quad read modes.
Functionality was verified on an HPE/Aruba AP-303 board.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
