There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is an error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable support for SDM845 based Titan 170 ISPs.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For Titan ISPs clocks fail to re-enable during vfe_get()
after any vfe has been halted and its corresponding power
domain power has been detached.
Since all of the clocks depend on all of the PDs, per
VFE PD detaching is no option for Gen2 HW.
In order to not have regressions on for Gen1 HW, refactor
the power domain management into hardware version specific
code paths.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add register definitions for version 170 of the Titan architecture
and implement support for the CSIPHY subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add register definitions for version 170 of the Titan architecture
and implement support for the CSID subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to support Qualcomm ISP hardware architectures that diverge
from older architectures, the CSID subdevice drivers needs to be refactored
to better abstract the different ISP hardware architectures.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSI-2 spec defines format identifier for Data Type (DT),
and how the Decode Format (DF) & Encode Format (EF) are implemented.
The spec does however not define the DF, EF or Plain Format (PF)
identifiers, as those are vendor specific.
Plain formats describe the size of the pixels written by the RDI
units to memory. PLAIN8 for example has the size 8 bits, and
PLAIN32 32 bits. The appropriate Plain Format is determined by
the Decode Format used. The smallest Plain Format that is able
to contain a pixel of the used Decode Format is the appropriate
one to use.
As the vendor specific identifiers differ between hardware
generations, split them out into separate headers.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add register definitions for version 170 of the Titan architecture
and implement support for the RDI output mode.
The RDI mode as opposed to the PIX output mode for the VFE unit does
not support any ISP functionality. This means essentially only
supporting dumping the output of the whatever the CSI decoder receives
from the sensor.
For example will a sensor outputting YUV pixel format frames, only
allow the VFE to dump those frames as they are received by the ISP
to memory through the RDI interface.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In order to support Qualcomm ISP hardware architectures that diverge
from older architectures, the VFE subdevice driver needs to be refactored
to better abstract the different ISP architectures.
Gen1 represents the CAMSS ISP architecture. The ISP architecture developed
after CAMSS, Titan, will be referred to as Gen2.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver supports multiple architecture versions of the Qualcomm ISP.
The CAMSS architecure which this driver is name after, and with the
introduction of this series, the Titan architecture.
The ISPIF is an IP-block that is only present in the CAMSS generation of
the architecture. In order to support the Titan generation, make the
ISPIF an optional subdevice.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add enum representing the SDM845 SOC, which incorporates version
170 of the Titan architecture ISP.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
trace_printk() should not be used in production code,
since extra memory is used for special buffers whenever
trace_puts() is used.
Replace it with dev_dbg() which provides all of the desired
debugging functionality.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Comment refers to ISPIF, but this is incorrect. Only
the VFE interrupts are handled by this function.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Function name in comment is wrong, and was changed to be
the same as the actual function name.
The comment was changed to kerneldoc format.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because of u32 type being used to store pixel clock rate, expression used
to calculate pipeline clocks (pixel_clock * bpp) produces wrong value due
to integer overflow. This patch changes data type used to store, pass and
retrieve pixel_clock from u32 to u64 to make this mistake less likely to
be repeated in the future.
Signed-off-by: Vladimir Lypak <junak.pub@gmail.com>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are places in the camss driver where camss_get_pixel_clock() is
called to get the pixel rate (using V4L2_CID_PIXEL_RATE control) and to
calculate the link frequency from it. There is a case when this would
not work: when V4L2_CID_PIXEL_RATE gets the rate at which the pixels are
read (sampled) from the sensor's pixel array, and this rate is different
from the pixel transmission rate over the CSI link, the link frequency
value can't be calculated from the pixel rate. One needs to use
V4L2_CID_LINK_FREQ to get the link frequency in this case.
Replace such calls to camss_get_pixel_clock() with calls to a wrapper
around v4l2_get_link_freq(). v4l2_get_link_freq() tries V4L2_CID_LINK_FREQ
first, and if it is not implemented by the camera sensor driver, falls
back to V4L2_CID_PIXEL_RATE to calculate the link frequency value from.
Calls to camss_get_pixel_clock() from vfe_[check,set]_clock_rates()
are left intact as it looks like this VFE clock does depend on the
rate the pixel samples comes out of the camera sensor, not on the
frequency at which the link between the sensor and the CSI receiver
operates.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The functions that add an async subdev to an async subdev notifier take
as an argument the size of the container structure they need to
allocate. This is error prone, as passing an invalid size will not be
caught by the compiler. Wrap those functions in macros that take a
container type instead of a size, and cast the returned pointer to the
desired type. The compiler will catch mistakes if the incorrect type is
passed to the macro, as the assignment types won't match.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> (core+ti-cal)
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This error path returns success but it should return -EINVAL.
Fixes: cba3819d1e ("media: camss: Format configuration per hardware version")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This test has a problem because we want to know if "k" is -1 or a
positive value less than "f->index". But the "f->index" variable is a
u32 so if "k == -1" then -1 gets type promoted to UINT_MAX which is
larger than "f->index". I've added an explicit test to check for -1.
Fixes: a3d412d4b9 ("media: Revert "media: camss: Make use of V4L2_CAP_IO_MC"")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement mbus_code filtering for format enumeration.
Without this patch libcamera errors out with:
"ERROR V4L2 v4l2_videodevice.cpp:982 /dev/video0[cap]: Media bus code
filtering not supported by the device"
This is the second version of this change which handles the case of
several pixel formats corresponding to one media bus format correctly.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This reverts commit c90f1178dc.
The assumption of "Each entry in formats[] table has unique mbus_code"
is valid for the RDI entities, but not for the PIX ones.
Reverting this patch and creating a new one which handles the PIX entities
correctly results in smaller and more straightforward patch than doing the
changes on top of the current version.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The SDM630/660 SoCs (and variants) have another clock source
for the PHY, which must be set to a rate that's equal or
greater than the CSI PHY timer clock: failing to do this
will produce PHY overflows when trying to get a stream from
a very high bandwidth camera sensor and outputting no frame
or a partial one.
Since I haven't found any usecase in which the csiX_phy
clock needs to be higher than the csiXphy_timer, let's just
set the same rate on both, which seems to work just perfect.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CSIPHY on SDM630/660 needs a slightly longer T_HS_CLK_MISS
configuration on lanes CFG4.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the Qualcomm SDM630/636/660 and SDA variants' camera
subsystem. These SoCs are equipped with:
- 3x CSI PHY 3-Phase v1.0 (downstream csiphy-v3.5)
- 4x CSID v5.0
- 2x ISPIF v3.0
- 2x VFE 4.8
As a note, this camera subsystem is very similar to the one that
is found in the MSM8998/APQ8098 SoCs.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the support for VFE 4.8 in the camss-vfe-4-7 driver, as this one
really is a minor revision, requiring the very same management and
basically having the same register layout as VFE 4.7, but needing
a different QoS and DS configuration, using a different register to
enable the wm and habing the same UB size for both instances (instead
of a different size between instance 0 and 1).
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation to add support for VFE 4.8, rename these functions
by adding the vfe version that they are referred to (for example,
vfe_get_ub_size -> vfe47_get_ub_size), as these are the only ones
that will be different for the VFE version 4.8.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Resetting the ISPIF VFE0 context is wrong if we are using the VFE1
for dual-camera or simply because a secondary camera is connected
to it: in this case the reset will always happen on the VFE0 ctx
of the ISPIF, which is .. useless.
Fix this usecase by adding the ISPIF_RST_CMD_1 address and choose
where to do the (or what to) reset based on the VFE line id.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
PM runtime put is not called in error handling paths.
Thus call pm_runtime_put_sync() if pm_runtime_get_sync() fails.
Fixes: 02afa816db ("media: camss: Add basic runtime PM support")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the definitions introduced by commit "media: camss: add support
for vidioc_enum_framesizes ioctl" instead of the hardcoded values.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
VIDIOC_ENUM_FRAMESIZES support in the video capture driver is required by
libcamera. Without this change libcamera errors out with:
"ERROR V4L2 v4l2_videodevice.cpp:1059 /dev/video0[cap]: Unable to enumerate
frame sizes: Inappropriate ioctl for device"
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement mbus_code filtering for format enumeration.
Without this patch libcamera errors out with:
"ERROR V4L2 v4l2_videodevice.cpp:982 /dev/video0[cap]: Media bus code
filtering not supported by the device"
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use vb2_video_unregister_device() to automatically stop streaming
at unregister time.
This avoids the use of vb2_queue_release() which should not be
called by drivers that set vdev->queue.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
camss_probe() does not free camss on error handling paths. The patch
introduces an additional error label for this purpose. Besides, it
removes call of v4l2_async_notifier_cleanup() from
camss_of_parse_ports() since its caller, camss_probe(), cleans up all
its resources itself.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently for msm_csiphy, msm_csid, and msm_ispif subdevices the media
entity function field is set to MEDIA_ENT_F_IO_V4L. This is incorrect
as MEDIA_ENT_F_IO_V4L implies V4L2 video node.
Change it to MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER as this is the best
fit from the functions defined in include/uapi/linux/media.h.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Tested-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently, v4l2_pipeline_pm_use() prototype is:
int v4l2_pipeline_pm_use(struct media_entity *entity, int use)
Where the 'use' argument shall only be set to '1' for enable/power-on,
or to '0' for disable/power-off. The integer return is specified
as only meaningful when 'use' is set to '1'.
Let's enforce this semantic by splitting the function in two:
v4l2_pipeline_pm_get and v4l2_pipeline_pm_put. This is done
for several reasons.
It makes the API easier to use (or harder to misuse).
It removes the constraint on the values the 'use' argument
shall take. Also, it removes the need to constraint
the return value, by making v4l2_pipeline_pm_put void return.
And last, it's more consistent with other kernel APIs, such
as the runtime pm APIs, which makes the code more symmetric.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_async_notifier_add_fwnode_subdev() did not take a reference of
the added fwnode, relying on the caller to handle that instead, in essence
putting the fwnode to be added if there was an error.
As the reference is eventually released during the notifier cleanup, this
is not intuitive nor logical. Improve this by always getting a reference
when the function succeeds, and the caller releasing the reference when it
does not *itself* need it anymore.
Luckily, perhaps, there were just a handful of callers using the function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Support for multiplanar and singleplanar formats is mutually exclusive,
at least in practice. In our attempt to unify support for support for
mplane and !mplane in v4l, let's get rid of the
->vidioc_enum_fmt_{vid,out}_cap_mplane() hooks and call
->vidioc_enum_fmt_{vid,out}_cap() instead.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[hverkuil-cisco@xs4all.nl: fix typos: pirv -> priv and prov -> priv]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When streaming is starting ask the sensor for its skip frames value.
Max supported frame skip is 29 frames, so clip it if it is higher.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Switch all media platform drivers to call v4l2_async_notifier_add_subdev()
to add asd's to a notifier, in place of referencing the notifier->subdevs[]
array. These drivers also must now call v4l2_async_notifier_init() before
adding asd's to their notifiers.
There may still be cases where a platform driver maintains a list of
asd's that is a duplicate of the notifier asd_list, in which case its
possible the platform driver list can be removed, and can reference the
notifier asd_list instead. One example of where a duplicate list has
been removed in this patch is xilinx-vipp.c. If there are such cases
remaining, those drivers should be optimized to remove the duplicate
platform driver asd lists.
None of the changes to the platform drivers in this patch have been
tested. Verify that the async subdevices needed by the platform are
bound at load time, and that the driver unloads and reloads correctly
with no memory leaking of asd objects.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We include device.h twice in camss.h. It's unnecessary.
hence just remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Multiple files in this driver fail to build because of missing
header inclusions:
drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c: In function 'csiphy_hw_version_read':
drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c:31:18: error: implicit declaration of function 'readl_relaxed'; did you mean 'xchg_relaxed'? [-Werror=implicit-function-declaration]
drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c: In function 'csiphy_hw_version_read':
drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c:52:2: error: implicit declaration of function 'writel' [-Werror=implicit-function-declaration]
Add linux/io.h there and in all other files that call
readl/writel and related interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use managed memory allocations for structs which are used until
the driver is removed.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
