The PHY initialisation parameters are not based on the pixel clock but
the TMDS clock rate which can be the pixel clock in the standard case,
but could be adjusted based on some parameters like the bits per color.
Since the TMDS clock rate is stored in our custom connector state
already, let's reuse it from there instead of computing it again.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-8-maxime@cerno.tech
The pixel rate is for now quite simple to compute, but with more features
(30 and 36 bits output, YUV output, etc.) will depend on a bunch of
connectors properties.
Let's store the rate we have to run the pixel clock at in our custom
connector state, and compute it in atomic_check.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-7-maxime@cerno.tech
When run with a higher bpc than 8, the clock of the HDMI controller needs
to be adjusted. Let's create a connector state that will be used at
atomic_check and atomic_enable to compute and store the clock rate
associated to the state.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-6-maxime@cerno.tech
drm_atomic_helper_connector_reset uses kmalloc which, from an API
standpoint, can fail, and thus setting connector->state to NULL.
However, our reset hook then calls drm_atomic_helper_connector_tv_reset
that will access connector->state without checking if it's a valid
pointer or not.
Make sure we don't end up accessing a NULL pointer.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-5-maxime@cerno.tech
Commit 63495f6b4a ("drm/vc4: hdmi: Make sure our clock rate is within
limits") was intended to compute the pixel rate to make sure we remain
within the boundaries of what the hardware can provide.
However, unlike what mode_valid was checking for, we forgot to take
into account the clock doubling flag that can be set for modes. Let's
honor that flag if it's there.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixes: 63495f6b4a ("drm/vc4: hdmi: Make sure our clock rate is within limits")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-4-maxime@cerno.tech
Since the CRTC setup in vc4 is split between the PixelValves/TXP and the
HVS, only the PV/TXP atomic hooks were updated in the previous commits, but
it makes sense to update the HVS ones too.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-2-maxime@cerno.tech
To support legacy gamma ioctls the drivers need to set
drm_crtc_funcs.gamma_set either to a custom implementation or to
drm_atomic_helper_legacy_gamma_set. Most of the atomic drivers do the
latter.
We can simplify this by making the core handle it automatically.
Move the drm_atomic_helper_legacy_gamma_set() functionality into
drm_color_mgmt.c to make drm_mode_gamma_set_ioctl() use
drm_crtc_funcs.gamma_set if set or GAMMA_LUT property if not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201211114237.213288-2-tomi.valkeinen@ti.com
Now that the semaphore is gone, our atomic_commit implementation is
basically drm_atomic_helper_commit with a somewhat custom commit_tail,
the main difference being that we're using wait_for_flip_done instead of
wait_for_vblanks used in the drm_atomic_helper_commit_tail helper.
Let's switch to using drm_atomic_helper_commit.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151138.1739736-8-maxime@cerno.tech
The HVS state now has both unassigned_channels that reflects the
channels that are not used in the associated state, and the in_use
boolean for each channel that says whether or not a particular channel
is in use.
Both express pretty much the same thing, and we need the in_use variable
to properly track the commits, so let's get rid of unassigned_channels.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151138.1739736-6-maxime@cerno.tech
If we're having two subsequent, non-blocking, commits on two different
CRTCs that share no resources, there's no guarantee on the order of
execution of both commits.
However, the second one will consider the first one as the old state,
and will be in charge of freeing it once that second commit is done.
If the first commit happens after that second commit, it might access
some resources related to its state that has been freed, resulting in a
use-after-free bug.
The standard DRM objects are protected against this, but our HVS private
state isn't so let's make sure we wait for all the previous FIFO users
to finish their commit before going with our own.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151138.1739736-5-maxime@cerno.tech
Required backmerge since we will be based on top of v5.11, and there
has been a request to backmerge already to upstream some features.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
BCM2711 DSI1 doesn't have the issue with the ARM not being
able to write to the registers, therefore remove the DMA
workaround for that compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-8-maxime@cerno.tech
DSI0 was partially supported, but didn't register with the main
driver, and the code was inconsistent as to whether it checked
port == 0 or port == 1.
Add compatible string and other support to make it consistent.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-6-maxime@cerno.tech
Most of the differences between DSI0 and DSI1 are handled through the
ID. However, the BCM2711 DSI is going to introduce one more variable to
the mix and will break some expectations of the earlier, simpler, test.
Let's add a variant structure that will address most of the differences
between those three controllers.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-5-maxime@cerno.tech
The DSI clocks setup function has been using an array to store the clock
name of either the DSI0 or DSI1 blocks, using the port ID to choose the
proper one.
Let's switch to an snprintf call to do the same thing and simplify the
array a bit.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-4-maxime@cerno.tech
The DSI1_PHY_AFEC0_PD_DLANE1 and DSI1_PHY_AFEC0_PD_DLANE3 register
definitions were swapped, so trying to use more than a single data
lane failed as lane 1 would get powered down.
(In theory a 4 lane device would work as all lanes would remain
powered).
Correct the definitions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-3-maxime@cerno.tech
The infoframes are sent at a regular interval as a data island packet,
so we don't need to wait for them to be sent when we're setting them up.
However, we do need to poll when we're enabling since the we can't
update the packet RAM until it has been sent.
Let's add a boolean flag to tell whether we want to poll or not to
support both cases.
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203074624.721559-1-maxime@cerno.tech
The new GEM object function drm_gem_cma_mmap() sets the VMA flags
and offset as in the old implementation and immediately maps in the
buffer's memory pages.
Changing CMA helpers to use the GEM object function allows for the
removal of the special implementations for mmap and gem_prime_mmap
callbacks. The regular functions drm_gem_mmap() and drm_gem_prime_mmap()
are now used.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201123115646.11004-3-tzimmermann@suse.de
The current HVS muxing code will consider the CRTCs in a given state to
setup their muxing in the HVS, and disable the other CRTCs muxes.
However, it's valid to only update a single CRTC with a state, and in this
situation we would mux out a CRTC that was enabled but left untouched by
the new state.
Fix this by setting a flag on the CRTC state when the muxing has been
changed, and only change the muxing configuration when that flag is there.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201120144245.398711-3-maxime@cerno.tech
If a CRTC is enabled but not active, and that we're then doing a page
flip on another CRTC, drm_atomic_get_crtc_state will bring the first
CRTC state into the global state, and will make us wait for its vblank
as well, even though that might never occur.
Instead of creating the list of the free channels each time atomic_check
is called, and calling drm_atomic_get_crtc_state to retrieve the
allocated channels, let's create a private state object in the main
atomic state, and use it to store the available channels.
Since vc4 has a semaphore (with a value of 1, so a lock) in its commit
implementation to serialize all the commits, even the nonblocking ones, we
are free from the use-after-free race if two subsequent commits are not ran
in their submission order.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201120144245.398711-2-maxime@cerno.tech
There's cross-talk on the RPi4 between the 2.4GHz channels used by the WiFi
chip and some resolutions, most notably 1440p at 60Hz.
In such a case, we can either reject entirely the mode, or lower slightly
the pixel frequency to remove the overlap. Let's go for the latter.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029134018.1948636-2-maxime@cerno.tech
We've had a number of muxing corner-cases with specific ways to reproduce
them, so let's document them to make sure they aren't lost and introduce
regressions later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105135656.383350-6-maxime@cerno.tech
The code that assigns HVS channels during atomic_check is starting to grow
a bit big, let's move it into a separate function.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105135656.383350-5-maxime@cerno.tech
The NUM_CHANNELS define has a pretty generic name and was right before the
function using it. Let's move to something that makes the hardware-specific
nature more obvious, and to a more appropriate place.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105135656.383350-4-maxime@cerno.tech
Even though it was pointed in the review by Daniel, and I thought to have
fixed it while applying the patches, but it turns out I forgot to commit
the fixes in the process. Properly fix it this time.
Fixes: dcda7c28bf ("drm/vc4: kms: Add functions to create the state objects")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105135656.383350-2-maxime@cerno.tech
The FIFO between the pixelvalve and the HDMI controller runs at 2 pixels
per clock cycle, and cannot deal with odd timings.
Let's reject any mode with such timings.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029122522.1917579-2-maxime@cerno.tech
The HDMI controller cannot go above a certain pixel rate limit depending on
the generations, but that limit is only enforced in mode_valid at the
moment, which means that we won't advertise modes that exceed that limit,
but the userspace is still free to try to setup a mode that would.
Implement atomic_check to make sure we check it in that scenario too.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029122522.1917579-1-maxime@cerno.tech
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/vc4/vc4_debugfs.c:25: warning: Function parameter or member 'minor' not described in 'vc4_debugfs_init'
drivers/gpu/drm/vc4/vc4_debugfs.c:62: warning: Function parameter or member 'dev' not described in 'vc4_debugfs_add_file'
drivers/gpu/drm/vc4/vc4_debugfs.c:62: warning: Function parameter or member 'name' not described in 'vc4_debugfs_add_file'
drivers/gpu/drm/vc4/vc4_debugfs.c:62: warning: Function parameter or member 'show' not described in 'vc4_debugfs_add_file'
drivers/gpu/drm/vc4/vc4_debugfs.c:62: warning: Function parameter or member 'data' not described in 'vc4_debugfs_add_file'
Cc: Eric Anholt <eric@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-41-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/vc4/vc4_v3d.c:131: warning: Function parameter or member 'vc4' not described in 'vc4_v3d_pm_get'
drivers/gpu/drm/vc4/vc4_v3d.c:231: warning: Function parameter or member 'vc4' not described in 'bin_bo_alloc'
Cc: Eric Anholt <eric@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Rob Clark <robdclark@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-40-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/vc4/vc4_hdmi.c: In function ‘vc4_hdmi_set_audio_infoframe’:
drivers/gpu/drm/vc4/vc4_hdmi.c:334:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Cc: Eric Anholt <eric@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-39-lee.jones@linaro.org
The alternative is to move them into the source file that uses then,
but they are large and intrusive, so that strategy is being avoided.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/vc4/vc4_hdmi_regs.h:282:39: warning: ‘vc5_hdmi_hdmi1_fields’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/vc4/vc4_hdmi_regs.h:206:39: warning: ‘vc5_hdmi_hdmi0_fields’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/vc4/vc4_hdmi_regs.h:145:39: warning: ‘vc4_hdmi_fields’ defined but not used [-Wunused-const-variable=]
Cc: Eric Anholt <eric@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201116174112.1833368-38-lee.jones@linaro.org
We need commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") to be able to merge Jason's cleanup patch.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+oiOgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGKBQIAJw6oad/FA7j9OO2
dMoaXb8UaBehGWgW2rdfWrFPV5v0DBnp/GkdRpLoZIjV3W4mBfnog7bIa4Eswlxo
Y8sZxo5/3JlgJQUkHvzR1TYk5z61lHkUw9Kj/cCyx6YdbjSl19AfFsnhQVVMuyp9
TXL2c7hxkHlw8eBGrymVu0Ip7Zq0x8O2g+8nQpmRcvaR6SBuSHdikDF/iWCtU1YW
wpk5eWEVaAO67keZOz6b+aCFHqjFX+1dUBBuPnslucYLR73Qi16hfaU9pebe97Gb
lX/MJ1bR9BeRp314cF0PYbm4WhKjRLudHOFJH8x3dj/BiYNrFK3SJGLiiTwsrAZ8
kytU0Xs=
=Ke/D
-----END PGP SIGNATURE-----
Merge v5.10-rc3 into drm-next
We need commit f8f6ae5d07 ("mm: always have io_remap_pfn_range() set
pgprot_decrypted()") to be able to merge Jason's cleanup patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch replaces the vmap/vunmap's use of raw pointers in GEM object
functions with instances of struct dma_buf_map. GEM backends are
converted as well. For most of them, this simply changes the returned type.
TTM-based drivers now return information about the location of the memory,
either system or I/O memory. GEM VRAM helpers and qxl now use ttm_bo_vmap()
et al. Amdgpu, nouveau and radeon use drm_gem_ttm_vmap() et al instead of
implementing their own vmap callbacks.
v7:
* init QXL cursor to mapped BO buffer (kernel test robot)
v5:
* update vkms after switch to shmem
v4:
* use ttm_bo_vmap(), drm_gem_ttm_vmap(), et al. (Daniel, Christian)
* fix a trailing { in drm_gem_vmap()
* remove several empty functions instead of converting them (Daniel)
* comment uses of raw pointers with a TODO (Daniel)
* TODO list: convert more helpers to use struct dma_buf_map
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Tested-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201103093015.1063-7-tzimmermann@suse.de
The function drm_gem_cma_prime_vunmap() is empty. Remove it before
changing the interface to use struct drm_buf_map.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201103093015.1063-3-tzimmermann@suse.de
idr_init() uses base 0 which is an invalid identifier for this driver.
The idr_alloc for this driver uses VC4_PERFMONID_MIN as start value for
ID range and it is #defined to 1. The new function idr_init_base allows
IDR to set the ID lookup from base 1. This avoids all lookups that
otherwise starts from 0 since 0 is always unused / available.
References: commit 6ce711f275 ("idr: Make 1-based IDRs more efficient")
Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105202135.GA145111@localhost
Now that atomic_check takes the global atomic state as a parameter, we
don't need to go through the pointer in the CRTC state.
This was done using the following coccinelle script:
@ crtc_atomic_func @
identifier helpers;
identifier func;
@@
static struct drm_crtc_helper_funcs helpers = {
...,
.atomic_check = func,
...,
};
@@
identifier crtc_atomic_func.func;
identifier crtc, state;
@@
func(struct drm_crtc *crtc, struct drm_atomic_state *state) {
...
- struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
... when != crtc_state
- crtc_state->state
+ state
...
}
@@
struct drm_crtc_state *crtc_state;
identifier crtc_atomic_func.func;
identifier crtc, state;
@@
func(struct drm_crtc *crtc, struct drm_atomic_state *state) {
...
- crtc_state->state
+ state
...
}
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102133834.1176740-3-maxime@cerno.tech
The commit dcda7c28bf ("drm/vc4: kms: Add functions to create the state
objects") removed the last users of the vc4 variable, but didn't remove
that variable resulting in a warning.
Fixes: dcda7c28bf ("drm/vc4: kms: Add functions to create the state objects")
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102162908.1436567-1-maxime@cerno.tech
In order to make the vc4_kms_load code and error path a bit easier to
read and extend, add functions to create state objects, and use managed
actions to cleanup if needed.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-6-maxime@cerno.tech
The job queue needs to be cleaned up using vc4_gem_destroy, but it's
not used consistently (vc4_drv's bind calls it in its error path, but
doesn't in unbind), and we can make that automatic through a managed
action. Let's remove the requirement to call vc4_gem_destroy.
Fixes: d5b1a78a77 ("drm/vc4: Add support for drawing 3D frames.")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-3-maxime@cerno.tech
The BO cache needs to be cleaned up using vc4_bo_cache_destroy, but it's
not used consistently (vc4_drv's bind calls it in its error path, but
doesn't in unbind), and we can make that automatic through a managed
action. Let's remove the requirement to call vc4_bo_cache_destroy.
Fixes: c826a6e106 ("drm/vc4: Add a BO cache.")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-1-maxime@cerno.tech
Most of the helpers to retrieve vc4 structures from the DRM base structures
rely on the fact that the first member of the vc4 structure is the DRM one
and just cast the pointers between them.
However, this is pretty fragile especially since there's no check to make
sure that the DRM structure is indeed at the offset 0 in the structure, so
let's use container_of to make it more robust.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028123752.1733242-1-maxime@cerno.tech
Since the components for a given device in ASoC are identified by their
name, it makes sense to add one even though it's not strictly necessary.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708144555.718404-1-maxime@cerno.tech
When running the trigger hook, ALSA by default will take a spinlock, and
thus will run the trigger hook in atomic context.
However, our HDMI driver will send the infoframes as part of the trigger
hook, and part of that process is to wait for a bit to be cleared for up to
100ms. To be nicer to the system, that wait has some usleep_range that
interact poorly with the atomic context.
There's several ways we can fix this, but the more obvious one is to make
ALSA take a mutex instead by setting the nonatomic flag on the DAI link.
That doesn't work though, since now the cyclic callback installed by the
dmaengine helpers in ALSA will take a mutex, while that callback is run by
dmaengine's virt-chan code in a tasklet where sleeping is not allowed
either.
Given the delay we need to poll the bit for, changing the usleep_range for
a udelay and keep running it from a context where interrupts are disabled
is not really a good option either.
However, we can move the infoframe setup code in the hw_params hook, like
is usually done in other HDMI controllers, that isn't protected by a
spinlock and thus where we can sleep. Infoframes will be sent on a regular
basis anyway, and since hw_params is where the audio parameters that end up
in the infoframes are setup, this also makes a bit more sense.
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027101558.427256-1-maxime@cerno.tech
If the DSI driver is the last to probe, component_add will try to run all
the bind callbacks straight away and return the error code.
However, since we depend on a power domain, we're pretty much guaranteed to
be in that case on the BCM2711, and are just lucky on the previous SoCs
since the v3d also depends on that power domain and is further in the probe
order.
In that case, the DSI host will not stick around in the system: the DSI
bind callback will be executed, will not find any DSI device attached and
will return EPROBE_DEFER, and we will then remove the DSI host and ask to
be probed later on.
But since that host doesn't stick around, DSI devices like the RaspberryPi
touchscreen whose probe is not linked to the DSI host (unlike the usual DSI
devices that will be probed through the call to mipi_dsi_host_register)
cannot attach to the DSI host, and we thus end up in a situation where the
DSI host cannot probe because the panel hasn't probed yet, and the panel
cannot probe because the DSI host hasn't yet.
In order to break this cycle, let's wait until there's a DSI device that
attaches to the DSI host to register the component and allow to progress
further.
Acked-by: Eric Anholt <eric@anholt.net>
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200707101912.571531-1-maxime@cerno.tech
New driver:
Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJfh579AAoJEAx081l5xIa+GqoP/0amz+ZN7y/L7+f32CRinJ7/
3e4xjXNDmtWG4Whe/WKjlYmbAcvSdWV/4HYpurW2BFJnOAB/5lIqYcS/PyqErPzA
w4EpRoJ+ZdFgmlDH0vdsDwPLT/HFmhUN9AopNkoZpbSMxrManSj5QgmePXyiKReP
Q+ZAK5UW5AdOVY4bgXUSEkVq2eilCLXf+bSBR/LrVQuNgu7GULX8SIy/Y1CuMtv8
LgzzjLKfIZaIWC+F/RU7BxJ7YnrVq7z7yXnUx8j2416+k/Wwe+BeSUCSZstT7q9G
UkX8jWfR7ZKqhwP+UQeSwDbHkALz7lv88nyjQdxJZ3SrXRe4hy14YjxnR4maeNAj
3TAYSdcAMWyRHqeEZIZ7Hj5sQtTq5OZAoIjxzH3vpVdAnnAkcWoF77pqxV8XPqTC
nw40DihAxQOshGwMkjd5DqkEwnMv43Hs1WTVYu9dPTOfOdqPNt+Vqp7Xl9Z46+kV
k6PDcx60T9ayDW1QZ6MoIXHta9E7ixzu7gYBL3vP4LuporY0uNG3bzF3CMvof1BK
sHYcYTdZkqbTD2d6rHV+TbpPQXgTtlej9qVlQM4SeX37Xtc7LxCYpnpUHKz2S/fK
1vyeGPgdytHblwlxwZOPZ4R2I/HTfnITdr4kMcJHhxAsEewfW1Rd4+stQqVJ2Mph
Vz+CFP2BngivGFz5vuky
=4H8J
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
The HVS FIFOs are currently assigned each time we have an atomic_check
for all the enabled CRTCs.
However, if we are running multiple outputs in parallel and we happen to
disable the first (by index) CRTC, we end up changing the assigned FIFO
of the second CRTC without disabling and reenabling the pixelvalve which
ends up in a stall and eventually a VBLANK timeout.
In order to fix this, we can create a special value for our assigned
channel to mark it as disabled, and if our CRTC already had an assigned
channel in its previous state, we keep on using it.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923084032.218619-2-maxime@cerno.tech
The current CRTC state reset hook in vc4 allocates a vc4_crtc_state
structure as a drm_crtc_state, and relies on the fact that vc4_crtc_state
embeds drm_crtc_state as its first member, and therefore can be safely
cast.
However, this is pretty fragile especially since there's no check for this
in place, and we're going to need to access vc4_crtc_state member at reset
so this looks like a good occasion to make it more robust.
Fixes: 6d6e500391 ("drm/vc4: Allocate the right amount of space for boot-time CRTC state.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923084032.218619-1-maxime@cerno.tech
GEM object functions deprecate several similar callback interfaces in
struct drm_driver. This patch replaces the per-driver callbacks with
per-instance callbacks in vc4. The only exception is gem_prime_mmap,
which is non-trivial to convert.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200923102159.24084-17-tzimmermann@suse.de
The HVS has three FIFOs that can be assigned to a number of PixelValves
through a mux.
However, changing that FIFO requires that we disable and then enable the
pixelvalve, so we want to assign FIFOs to all the enabled CRTCs, and not
just the active ones.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200918145918.101068-1-maxime@cerno.tech
The vc4 display engine has a first controller called the HVS that will
perform the composition of the planes. That HVS has 3 FIFOs and can
therefore compose planes for up to three outputs. The timings part is
generated through a component called the Pixel Valve, and the BCM2711 has 6
of them.
Thus, the HVS has some bits to control which FIFO gets output to which
Pixel Valve. The current code supports that muxing by looking at all the
CRTCs in a new DRM atomic state in atomic_check, and given the set of
constraints that we have, assigns FIFOs to CRTCs or reject the mode
entirely. The actual muxing will occur during atomic_commit.
However, that doesn't work if only a fraction of the CRTCs' state is
updated in that state, since it will ignore the CRTCs that are kept running
unmodified, and will thus unassign its associated FIFO, and later disable
it.
In order to make the code work as expected, let's pull the CRTC state of
all the enabled CRTC in our atomic_check so that we can operate on all the
running CRTCs, no matter whether they are affected by the new state or not.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917121623.42023-1-maxime@cerno.tech
Handing the return value of drm_universal_plane_init to fix the following
W=1 kernel build warning(s):
vc4_plane.c: In function ‘vc4_plane_init’:
vc4_plane.c:1340:6: warning: variable ‘ret’ set but not
used [-Wunused-but-set-variable]
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1599811777-34093-1-git-send-email-tiantao6@hisilicon.com
Clang warns:
drivers/gpu/drm/vc4/vc4_plane.c:901:27: warning: operator '?:' has lower
precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
fb->format->has_alpha ?
~~~~~~~~~~~~~~~~~~~~~ ^
drivers/gpu/drm/vc4/vc4_plane.c:901:27: note: place parentheses around
the '|' expression to silence this warning
fb->format->has_alpha ?
~~~~~~~~~~~~~~~~~~~~~ ^
drivers/gpu/drm/vc4/vc4_plane.c:901:27: note: place parentheses around
the '?:' expression to evaluate it first
fb->format->has_alpha ?
~~~~~~~~~~~~~~~~~~~~~~^
1 warning generated.
Add the parentheses as that was clearly intended, otherwise
SCALER5_CTL2_ALPHA_PREMULT won't be added to the list.
Fixes: c54619b0bf ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1150
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910171831.4112580-1-natechancellor@gmail.com
Clang warns 100+ times in the vc4 driver along the lines of:
drivers/gpu/drm/vc4/vc4_hdmi_phy.c:518:13: warning: implicit conversion
from enumeration type 'enum vc4_hdmi_field' to different enumeration
type 'enum vc4_hdmi_regs' [-Wenum-conversion]
HDMI_WRITE(HDMI_TX_PHY_POWERDOWN_CTL,
~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
The HDMI_READ and HDMI_WRITE macros pass in enumerators of type
vc4_hdmi_field but vc4_hdmi_write and vc4_hdmi_read expect a enumerator
of type vc4_hdmi_regs, causing a warning for every instance of this.
Update the parameter type so there is no more mismatch.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1149
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910170401.3857250-1-natechancellor@gmail.com
The variant->registers[] has ->num_registers elements so the >
comparison needs to be changes to >= to prevent an out of bounds
access.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910100748.GA79916@mwanda
card->owner is a required property and since commit 81033c6b58 ("ALSA:
core: Warn on empty module") a warning is issued if it is empty. Fix lack
of it. This fixes following warning observed on RaspberryPi 3B board
with ARM 32bit kernel and multi_v7_defconfig:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 210 at sound/core/init.c:207 snd_card_new+0x378/0x398 [snd]
Modules linked in: vc4(+) snd_soc_core ac97_bus snd_pcm_dmaengine bluetooth snd_pcm snd_timer crc32_arm_ce raspberrypi_hwmon snd soundcore ecdh_generic ecc bcm2835_thermal phy_generic
CPU: 1 PID: 210 Comm: systemd-udevd Not tainted 5.8.0-rc1-00027-g81033c6b584b #1087
Hardware name: BCM2835
[<c03113c0>] (unwind_backtrace) from [<c030bcb4>] (show_stack+0x10/0x14)
[<c030bcb4>] (show_stack) from [<c071cef8>] (dump_stack+0xd4/0xe8)
[<c071cef8>] (dump_stack) from [<c0345bfc>] (__warn+0xdc/0xf4)
[<c0345bfc>] (__warn) from [<c0345cc4>] (warn_slowpath_fmt+0xb0/0xb8)
[<c0345cc4>] (warn_slowpath_fmt) from [<bf02ff74>] (snd_card_new+0x378/0x398 [snd])
[<bf02ff74>] (snd_card_new [snd]) from [<bf11f0b4>] (snd_soc_bind_card+0x280/0x99c [snd_soc_core])
[<bf11f0b4>] (snd_soc_bind_card [snd_soc_core]) from [<bf12f000>] (devm_snd_soc_register_card+0x34/0x6c [snd_soc_core])
[<bf12f000>] (devm_snd_soc_register_card [snd_soc_core]) from [<bf165654>] (vc4_hdmi_bind+0x43c/0x5f4 [vc4])
[<bf165654>] (vc4_hdmi_bind [vc4]) from [<c09d660c>] (component_bind_all+0xec/0x24c)
[<c09d660c>] (component_bind_all) from [<bf15c44c>] (vc4_drm_bind+0xd4/0x174 [vc4])
[<bf15c44c>] (vc4_drm_bind [vc4]) from [<c09d6ac0>] (try_to_bring_up_master+0x160/0x1b0)
[<c09d6ac0>] (try_to_bring_up_master) from [<c09d6f38>] (component_master_add_with_match+0xd0/0x104)
[<c09d6f38>] (component_master_add_with_match) from [<bf15c588>] (vc4_platform_drm_probe+0x9c/0xbc [vc4])
[<bf15c588>] (vc4_platform_drm_probe [vc4]) from [<c09df740>] (platform_drv_probe+0x6c/0xa4)
[<c09df740>] (platform_drv_probe) from [<c09dd6f0>] (really_probe+0x210/0x350)
[<c09dd6f0>] (really_probe) from [<c09dd940>] (driver_probe_device+0x5c/0xb4)
[<c09dd940>] (driver_probe_device) from [<c09ddb38>] (device_driver_attach+0x58/0x60)
[<c09ddb38>] (device_driver_attach) from [<c09ddbc0>] (__driver_attach+0x80/0xbc)
[<c09ddbc0>] (__driver_attach) from [<c09db820>] (bus_for_each_dev+0x68/0xb4)
[<c09db820>] (bus_for_each_dev) from [<c09dc9f8>] (bus_add_driver+0x130/0x1e8)
[<c09dc9f8>] (bus_add_driver) from [<c09de648>] (driver_register+0x78/0x110)
[<c09de648>] (driver_register) from [<c0302038>] (do_one_initcall+0x50/0x220)
[<c0302038>] (do_one_initcall) from [<c03db544>] (do_init_module+0x60/0x210)
[<c03db544>] (do_init_module) from [<c03da4f8>] (load_module+0x1e34/0x2338)
[<c03da4f8>] (load_module) from [<c03dac00>] (sys_finit_module+0xac/0xbc)
[<c03dac00>] (sys_finit_module) from [<c03000c0>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xeded9fa8 to 0xeded9ff0)
...
---[ end trace 6414689569c2bc08 ]---
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701073949.28941-1-m.szyprowski@samsung.com
The BCM2711 has a reworked display pipeline, and the load tracker needs
some adjustment to operate properly. Let's add a compatible for BCM2711
and disable the load tracker until properly supported.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/beac4f9ef0261bca731a0402c8354e9af740519c.1599120059.git-series.maxime@cerno.tech
In order to avoid pixels getting stuck in an unflushable FIFO, we need when
we disable the HDMI controller to switch away from getting our pixels from
the pixelvalve and instead use blank pixels, and switch back to the
pixelvalve when we enable the HDMI controller.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fde3efb1ad79f4476a73d310cbba3ec07dc6dabe.1599120059.git-series.maxime@cerno.tech
The VID_CTL setup is done in several places in the driver even though it's
not really required. Let's simplify it a bit to do the configuration in one
go.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/08e7ebb605a560fcc149b69b4af52753a7870b2f.1599120059.git-series.maxime@cerno.tech
In order to prevent some pixels getting stuck in an unflushable FIFO on
bcm2711, we need to enable the HVS, the pixelvalve (the CRTC) and the HDMI
controller (the encoder) in an intertwined way, and with tight delays.
However, the atomic callbacks don't really provide a way to work with
either constraints, so we need to roll our own callbacks so that we can
provide those guarantees.
Since those callbacks have been implemented and called in the CRTC code, we
can just implement them in the HDMI driver now.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2e9226d971117065f3b97e597f04f7fe2f0c134c.1599120059.git-series.maxime@cerno.tech
In order to avoid a pixel getting stuck in an unflushable FIFO, we need to
recenter the FIFO every time we're doing a modeset and not only if we're
connected to an HDMI monitor.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b3faaf05ac6c4d3c364d28fa441571eb85903269.1599120059.git-series.maxime@cerno.tech
The current code has some logic, disabled by default, to dump the register
setup in the HDMI controller.
However, since we're going to split those functions in multiple, shorter,
functions that only make sense where they are called in sequence, keeping
the register dump makes little sense.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c8c8d388f2d32fc3536336be36d003a862487eb7.1599120059.git-series.maxime@cerno.tech
The HDMI driver was registering a single ALSA card so far with the name
vc4-hdmi.
Obviously, this is not going to work anymore when we will have multiple
HDMI controllers since we will end up trying to register two files with the
same name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e60a37444e848a384a45707a21d6df8883115f86.1599120059.git-series.maxime@cerno.tech
The audio configuration has changed for the BCM2711, with notably a
different parent clock and a different channel configuration.
Make that modular to be able to support the BCM2711.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/85a8ca721c2d800be758c55870cea98536749680.1599120059.git-series.maxime@cerno.tech
ALSA's iec958 plugin by default sets the block start preamble
to 8, whilst this driver was programming the hardware to expect
0xF.
Amend the hardware config to match ALSA.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d0b126deb228baf1244c91e02ac0a8f7c9c60dc5.1599120059.git-series.maxime@cerno.tech
If the encoder is disabled and re-enabled (eg mode change) all infoframes
are reset, whilst the audio subsystem know nothing about this change.
The driver therefore needs to reinstate the audio infoframe for
itself.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cd579ccc2c9b9d2fce0ebaf32f847cedb0e4a7a2.1599120059.git-series.maxime@cerno.tech
The register range used for audio setup in the previous generations of
SoC were always the second range in the device tree. However, now that
the BCM2711 has way more register ranges, it makes sense to retrieve it
by names for it, while preserving the id-based lookup as a fallback.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a1ba5605fe1006a1ead5262ef3d66ea5d0750381.1599120059.git-series.maxime@cerno.tech
The HSM clock needs to be running at 101% the pixel clock of the HDMI
controller, however it's shared between the two HDMI controllers, which
means that if the resolutions are different between the two HDMI
controllers, and the lowest resolution is on the second (in enable order)
controller, the first HDMI controller will end up with a smaller than
expected clock rate.
Since we don't really need an exact frequency there, we can simply change
the minimum rate we expect instead.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/821992209cc0d7a83254bf26fe2bf507ef0994d2.1599120059.git-series.maxime@cerno.tech
The HSM clock needs to be setup at around 101% of the pixel rate. This
was done previously by setting the clock rate to 163.7MHz at probe time and
only check in mode_valid whether the mode pixel clock was under the pixel
clock +1% or not.
However, with 4k we need to change that frequency to a higher frequency
than 163.7MHz, and yet want to have the lowest clock as possible to have a
decent power saving.
Let's change that logic a bit by setting the clock rate of the HSM clock
to the pixel rate at encoder_enable time. This would work for the
BCM2711 that support 4k resolutions and has a clock that can provide it,
but we still have to take care of a 4k panel plugged on a BCM283x SoCs
that wouldn't be able to use those modes, so let's define the limit in
the variant.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7e692ddc231d33dd671e70ea04dd1dcf56c1ecb3.1599120059.git-series.maxime@cerno.tech
The mode_valid hook on the encoder uses a pointer to a drm_encoder called
crtc, which is pretty confusing. Let's rename it to encoder to make it
clear what it is.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7fbabab03992efe4a3a3640ac5ee2bb49b1c7338.1599120059.git-series.maxime@cerno.tech
Similarly to the audio support, CEC support is not there yet for the
BCM2711, so let's skip entirely the CEC initialization through a variant
flag.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bd0c4afa83b4e121692352cdc2dd1886162c7552.1599120059.git-series.maxime@cerno.tech
The CEC init code was put directly into the bind function, which was quite
inconsistent with how the audio support was done, and would prevent us from
further changes to skip that initialisation entirely.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/21f4717e076291522d0784a7fd3774d8e97eaf01.1599120059.git-series.maxime@cerno.tech
The HDMI driver was registering a single debugfs file so far with the name
hdmi_regs.
Obviously, this is not going to work anymore when will have multiple HDMI
controllers since we will end up trying to register two files with the same
name.
Let's use the variant to avoid that name conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9505c1eb40b3ef3709277bf9e8af77917b249c32.1599120059.git-series.maxime@cerno.tech
The vc4 CRTC will use the encoder type to control its output clock
muxing. However, this will be different from HDMI0 to HDMI1, so let's
store our type in the variant structure so that we can support multiple
controllers later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2736a86b498551ba9dbc5803c5bb910627a2550c.1599120059.git-series.maxime@cerno.tech
Similarly to the previous patches, the timings setup in the HDMI controller
of the BCM2711 is slightly different, mostly because it supports higher
resolutions and thus needed more spaces for the various timings, resulting
in the register layout changing.
Let's add a callback for that as well.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0cfcbb379212f90b4abc76c0ccf3b90d1d7c0268.1599120059.git-series.maxime@cerno.tech
Similarly to the previous patches, the CSC setup is slightly different in
the BCM2711 than in the previous generations. Let's add a callback for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5c19bbf10153cb42ca0fb67e08606c8295c17236.1599120059.git-series.maxime@cerno.tech
The HDMI PHY in the BCM2711 HDMI controller is significantly more
complicated to setup than in the older BCM283x SoCs.
Let's add hooks to enable and disable the PHY.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7216826284dbc60a58bdacd662805d20699e5c80.1599120059.git-series.maxime@cerno.tech
