[Why]
When running games or benchmarking with v-sync disabled, disabling
a plane (which is v-sync) can cause underflow. This is caused by
flips pending before pipe locking being applied after locks are
released and pipes could have been re-arranged or disconnected. This
could potentially apply a flip on incorrect pipe. Also, previous logic
of always locking pipes was unnecessary.
[How]
Only lock the pipes when there is a pipe being disabled to increase
efficiency. Before the pipes are locked, check that any pending flips
are cleared to ensure the flips are applied to the correct pipe.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update dc for vangogh support.
v2: fix compilation without DCN 301 set.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When running a game/benchmark with v-sync disabled, disabling a plane
(which is v-sync) can cause an underflow. This is due to flips that are
pending before pipe locking being applied after locks are released and
pipes have been re-arranged or disconnected. This can potentially apply
a flip on the incorrect pipe.
[How]
Check that any pending flips are cleared before locking any pipes to
ensure flips are applied on the correct pipes.
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In DCN10 when a panel with YCbCr420 capability is connected via
USB-C to HDMI active dongle, no YCbCr420 option is listed in
Radeon settings.
[HOW]
Enable DP YCbCr420 mode support for DCN10
Signed-off-by: Gary Li <gary.li@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When disabling DP video, the current REG_WAIT timeout
of 50ms is too low for certain cases with very high
VSYNC intervals.
[HOW]
Increase the timeout to 102ms, so that
refresh rates as low as 10Hz can be handled properly.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
[Why]
We dont's turn off backlight before power off eDP (VDD),
which is a violation of eDP specs.
[How]
Power off eDP backlight before power off eDP
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The ctx field of dc_transfer_func is not always populated and therefore
isn't reliable.
[How]
Remove dc context from dc_transfer_func
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are situations where we go from 2 pipe to 1 pipe in MPO, but this
isn't a pipe split being lost -- it's a plane disappearing in (i.e. video overlay
goes away) so we lose one pipe. In these situations we don't want to
disable the pipe in a separate operation from the rest of the pipe
programming sequence. We only want to disable a pipe in a
separate operation when we're actually disabling pipe split.
[How]
Make sure the pipe being lost has the same stream AND plane
as the old top pipe to ensure.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function set_mst_bandwidth is poorly name since it isn't clear what
it does, and it also does not reflect any part of the allocation sequence
described in the DP spec.
[How]
Rename the function set_mst_bandwidth to set_throttled_vcp_size.
Signed-off-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When pipe locks are being taken we wait for flip pending to clear first.
In some cases the pipe mapping is changed and the pending we're checking
for will never clear.
[How]
Don't check disabled pipes for flip pending.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
update_clocks might not be called on headless adapters. This means
DISPLAY_OFF may not be sent in headless cases.
[HOW]
If hardware is powered down on boot because it is headless (mode set
does not happen on that adapter) also send DISPLAY_OFF notification.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These aren't stable on some platform configurations when driving
multiple displays, especially on higher resolution.
In particular the delay in asserting p-state and validating from
x86 outweights any power or performance benefit from the hardware
composition.
Under some configurations this will manifest itself as extreme stutter
or unresponsiveness especially when combined with cursor movement.
[How]
Disable these for now. Exposing overlays to userspace doesn't guarantee
that they'll be able to use them in any and all configurations and it's
part of the DRM contract to have userspace gracefully handle validation
failures when they occur.
Valdiation occurs as part of DC and this in particular affects RV, so
disable this in dcn10_global_validation.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds ARM64 support into the DCN. This mainly enables support
for Navi graphics cards. The dcn10 changes haven't been tested,
since I don't have the relevant hardware available, but there
is no way to conditionally disable them, so I've done them anyway.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When changing pixel formats for HDR (e.g. ARGB -> FP16)
there are configurations that change from 2 pipes to 1 pipe.
In these cases, it seems that disconnecting MPCC and doing
a surface update at the same time(after unlocking) causes
some registers to be updated slightly faster than others
after unlocking (e.g. if the pixel format is updated to FP16
before the new surface address is programmed, we get
corruption on the screen because the pixel formats aren't
matching). We separate disconnecting MPCC from the rest
of the pipe programming sequence to prevent this.
[How]
Move MPCC disconnect into separate operation than the
rest of the pipe programming.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Using FRAME_UPDATE will result in infopacket to be potentially updated
one frame late.
In commit stream scenarios for previously active stream, some stale
infopacket data from previous config might be erroneously sent out on
initial frame after stream is re-enabled.
[How]
Switch to using IMMEDIATE_UPDATE mode
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The format in MPCC should be 444
[How]
do not modify the mpcc black color according to pixel encoding format
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Struct dcn_dsc_state is used for reading current state
and parameters of DSC on a pipe, the target rate parameter
uses bytes per pixel even though its reading BITS_PER_PIXEL
register.
[How]
Changing it to Bits Per Pixel for consistency.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new calculated dispclk, dppclk are stored in
context->bw_ctx.bw.dcn.clk.dispclk_khz, dppclk_khz. Current dispclk,
dppclk are from dc->clk_mgr->clks.dispclk_khz. dcn_validate_bandwidth
compute new dispclk, dppclk. dispclk will put in use after
optimize_bandwidth when ramp_up_dispclk_with_dpp is called. There are
two places for dppclk be put in use. One location is the same as the
location as dispclk. Another is within update_dchubp_dpp which happens
between pre_bandwidth and optimize_bandwidth. dppclk updated within
update_dchubp_dpp will cause new clock values of dispclk and dppclk not
be in use at the same time. when clocks are decreased, this may cause
dppclk is lower than current configuration and let pipe stuck. for
example, eDP + external dp, change resolution of DP from 1920x1080x144hz
to 1280x960x60hz.
before change: dispclk = 337889 dppclk = 337889
change mode, dcn_validate_bandwidth calculate
dispclk = 143122 dppclk = 143122
update_dchubp_dpp be executed before dispclk be updated,
dispclk = 337889, but dppclk use new value dispclk /2 =
168944. this will cause pipe pstate warning issue.
[How]
between pre_bandwidth and optimize_bandwidth, while dispclk is going to
be decreased, keep dppclk = dispclk
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless systems, if set mode is not called, hardware will not be
powered down on boot, causing HW/SW discrepancies. Powering down
hardware on boot will ensure SW state is accurate.
[HOW]
Set a timer callback on boot for 10 seconds. If set mode is not called
within that time, power down hardware. Otherwise, do not power down.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid s3 faild at the first cycle on renoir platform, it needs to
revert this patch:
drm/amd/display: add mechanism to skip DCN init
Signed-off-by: changfeng <Changfeng.Zhu@amd.com>
Ackedy-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver re-initialize registers already set in FW
[How]
Transfer init to FW
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If optimized init is done in FW. DCN init be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.
[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Check max_tmds_clk_mhz firstly will restrict pixel clock under HDMI
1.4, thus HDMI2.0 port can't correctly support 4K 60Hz.
[HOW]
Fine tune the logic to check max_forum_tmds_clk_mhz firstly.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently DC doesn't check requested pixel clock against an EDID
specified TMDS max clock if it exists, passing modes that should fail
[HOW]
Add max TMDS clk to edid caps and perform check during validation
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc->hwss->edp_backlight_control is null, it would casue it only be off
main-link of eDP. It is not worng behavior for eDP power sequence off.
[how]
Must use hwseq->funcs.edp_backlight_control finction pointer for edp
backlight.
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hw lock manager adds the ability to lock pipe, cursor, and dig in fw.
[How]
Send hw lock command to fw to lock pipe, cursor, and dig.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to guard some new DCN3.0 stuff.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN3 HUBP (Display to data fabric interface
pipe)
HW Blocks:
+--------++------+
| HUBBUB || HUBP |
+--------++------+
|
v
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN3, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unit enter to S4, garbage show on screen when do OPTC blank.
[How]
Wait for vblank then do OPTC blank
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If VUPDATE_END is before VUPDATE_START the delay calculated can become
very large, causing a soft hang.
[How]
Take the absolute value of the difference between START and END.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We dropped the delay after changed the cursor functions locking the
entire pipe to locking just the CURSOR registers to fix page flip
stuttering - this introduced cursor stuttering instead, and an underflow
issue.
The cursor update can be delayed indefinitely if the cursor update
repeatedly happens right around VUPDATE.
The underflow issue can happen if we do a viewport update on a pipe
on the same frame where a cursor update happens around VUPDATE - the
old cursor registers are retained which can be in an invalid position.
This can cause a pipe hang and indefinite underflow.
[How]
The complex, ideal solution to the problem would be a software
triple buffering mechanism from the DM layer to program only one cursor
update per frame just before VUPDATE.
The simple workaround until we have that infrastructure in place is
this change - bring back the delay until VUPDATE before locking, but
with some corrections to the calculations.
This didn't work for all timings before because the calculation for
VUPDATE was wrong - it was using the offset from VSTARTUP instead and
didn't correctly handle the case where VUPDATE could be in the back
porch.
Add a new hardware sequencer function to use the existing helper to
calculate the real VUPDATE start and VUPDATE end - VUPDATE can last
multiple lines after all.
Change the udelay to incorporate the width of VUPDATE as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
One call was forcing stutter on instead of looking at the debug option.
Ensure we always check the debug option unless we want to force stutter
off.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
same with CL#1711022(correcting yuv420 black color in function dcn10_blank_pixel_data,program_scaler),
yuv420 black color also needs to be correct when enabling HDMI stream at the resume procedure.
[How]
correcting the yuv420 black color according to the way how 420 is packed :2 channels carry Y component,
1 channel alternate between Cb and Cr.
Signed-off-by: yanyan kang <Yanyan.Kang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
What a mode change is requested for the same timing a full stream reset
can occur in some cases which causes monitor to blank for a few seconds.
[How]
Do not consider infoframe updates as needing a full stream reset as they
will be handled on the first flip after a modeset when surface
information is available.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
panel_cntl specific register should be access in panel_cntl object.
[How]
Move these register access from abm to panel_cntl.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_stream_encoder.c:1277:11: warning: variable ‘speakers’ set but not used [-Wunused-but-set-variable]
It is introduced by commit 0c41891c81 ("drm/amd/display:
Refactor stream encoder for HW review"), but never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_dpp.c:137:11: warning: variable ‘pixel_width’ set but not used [-Wunused-but-set-variable]
It is introduced by commit 70ccab6040 ("drm/amdgpu/display:
Add core dc support for DCN"), but never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current locking scheme for cursor can result in a flip missing
its vsync, deferring it for one or more vsyncs. Result is a
potential for stuttering when cursor is moved.
[How]
Use cursor update lock so that flips are not blocked while cursor
is being programmed.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
modules/color calculates various colour operations which are translated
to abstracted HW. DCE 5-12 had almost no important changes, but
starting with DCN1, every new generation comes with fairly major
differences in color pipeline.
We would hack it with some DCN checks, but a better approach is to
abstract color pipe capabilities so modules/DM can decide mapping to
HW block based on logical capabilities,
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add set backlight to hw sequencer, dmu communication will
be handled in hw sequencer for new asics.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
it doesn't represent panel specifically, it's more like the control
logic for the panel
[How]
change from panel to panel cntl to make it a bit more clear
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HW rotation was enabled in DAL3 but hubp cursor calculations for HW roation
were only added to dcn20.
[How]
Add hubp cursor position calculation changes to dcn10.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
panel power sequencer is currently just sitting in hwseq but it really
it tied to internal panels
[How]
make a new panel struct to contain power sequencer code
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some cases were incorrectly reporting the wrong visual confirm, even
though they were working as expected.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Optc needs to know if timing is enabled with ODM or DSC before computing
crc. Otherwise value computed will be inaccurate. Before this change,
the CRC computed without ODM is not equal to the CRC computed with ODM
for the same timing. This is unexpected as we are driving the same
timing despite of the underlaying hardware setup to achieve it. This is
caused by missing hardware programming sequence to support it.
[how]
Add the new programming sequence based on hardware guide.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Aconnector is not necessary to be NULL in order to read dpcd
successfully.
Actually if we rely on checking aconnector here, we won't be able
to turn off all displays before doing display detection. That will
cause some MST hubs not able to light up.
[How]
Remove aconnector check when turning off all displays at
hardware initialization stage.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <joseph.gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When display is connected with a native DP port, DP2 mode register value
is a don't care. Driver mistakenly reduce max supported lane count to 2
lane based on the don't care value.
[how]
Add additional check only if USB C DP alt mode is enabled, we will
determine max lane count supported based on current mode.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some usecases, like tiled display, the stream and plane configuration
can be setup in a way where the caller expects DAL to perform the
clipping, eg:
P0:
src_rect(0, 0, w, h)
dst_rect(0, 0, w, h)
P1:
src_rect(w, 0, w, h)
dst_rect(0, 0, w, h)
Cursor is enabled on both streams with the same position.
This can result in double cursor on tiled display, even though this
behavior is technically correct from the DC interface point of view.
We need a mechanism to control this dynamically.
[How]
This is something that should live in the DM layer based on detection
of the specified configuration but it's not something that we really
have enough information to deal with today.
Add a flag to the cursor position state that specifies whether we
want DC to do the translation or not and make it opt-in and let
the DM decide when to do it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New formula + cursor change causing underflow
on certain configs
[How]
Rever to old formula
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Changing policy to dynamic will allow 4k multi display configs
to be supported at DPM0
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor is drawn as part of the framebuffer for a plane on AMD hardware.
The cursor position on the framebuffer does not change even if the
source rect viewport for the cursor does. This causes the cursor to be
clipped.
The following IGT tests fail as a result of this issue:
- kms_plane_cursor@pipe-*-viewport-size-*
[How]
Offset cursor position by plane source rect viewport. If the viewport
is unscaled then the cursor is now correctly positioned on any
plane - primary or overlay.
There is still a hardware limitation for dealing with the cursor size
being incorrectly scaled but that's not something we can address.
Add some documentation explaining some of this in the code while we're
at it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
blank all dp stream would impact edp
[how]
only blank the one which will be powered off
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The power_down() function was only defined for specific asics and will
crash the system if it is called by an asic with eDP connected that does
not have it defined.
[HOW]
Add a check for the function's existence before calling it.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
power off dp receiver directly cause garbage during hw init
[how]
blank dp stream and then power off receiver
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On headless boot a DIG may be turned on by VBIOS on RN. This leads to
display_count being non-zero in hybrid graphics cases leading to SMU
DISPLAY_OFF message not being sent.
[HOW]
Power down hardware on boot
if seamless boot is not occurring
(power_down_display_on_boot == 1)
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CTM was only supported at CRTC level and we need color space conversion
in linear space at plane level.
[How]
- Add plane-level CTM to dc interface
- Program plane-level CTM in DCN
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some monitors extreme flickering can occur while using LFC for if
we're not doing the DRR timing update for V_TOTAL_MIN / V_TOTAL_MAX at
the DP start of frame.
Hardware can default to any time in the frame which isn't the behavior
we want.
[How]
Add a new function for setting the double buffering mode for DRR timing.
Default to DP start of frame double buffering on timing generator init.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
P010 pixel format is not declared as supported in DRM and DM.
[How]
Add P010 format to the support list presented to DRM and checked in DM
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
underflow happened when playing video on 1366x768 + 4K clone mode due to
incorrect handle watermark change flag and lower down clocks to early.
[How]
Check watermark change flag when decide doing optimized, and check
optimized required flag to do clock update.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
this register not exist in some asic, based on request remove this from
dc.
[how]
add guard for sanization.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In headless boot cases, self refresh control registers are not
programmed on boot. In certain hybrid graphics cases this may cause
cstate entering to get blocked causing a hang.
[HOW]
Program self refresh control register on boot.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The default value for disable_dmcu is true, even for asics that require
dmcu.
[How]
Set flag properly per asic.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
on some displays that prefer swapped polarity we were seeing L/R images
swapped because OTG_STEREO_SYNC_OUTPUT_POLARITY would always be mapped
to 0
[how]
fix initial dal3 implementation to properly update the polarity field
according to the crtc_stereo_flags (same as
OTG_STEREO_EYE_FLAG_POLARITY)
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
System isn't able to enter S0i3 due to not send display count 0 to smu.
When dpms off, clk changed flag is cleared alreay, and it is checked
when doing optimized bandwidth, and update clocks is bypassed due to the
flag is unset.
[How]
Remove check flag incide the function since watermark values and clocks
values are checked during update to determine whether to perform it, no
need to check it again outside the function.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup calculation is incorrect due to use 2 number of cursors and
result in an underflow when playing video in full screen mode and
combines graphic plane and video plane.
[How]
Apply new policy for dml calculation.
1 cursor for graphic plane, 0 cursor for video plane.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we have single channel memory, we can not light up 2 4k displays
with a 1080p edp, because we don't have enough bw by a small margin.
this small margin comes from dcc meta being too large. We however don't
have this dcc meta when we create fake planes so, before the flip we
will not filter out the mode for 2 4k displays with a 1080p edp
[how]
Change get_default_swizzle_mode to something more general so we don't
end up with a separate function for every missing field in the fake
plane. Add a reasonable dcc meta to the fake plane when it is filled in,
so we filter out modes that don't have enough bandwidth. To do this, we
take the screen width and align it to 1024(8k 60)
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow sometimes occurs during transition into MPO with stutter
enabled.
[How]
When transitioning into MPO, disable stutter. Re-enable stutter within
one frame.
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some display configuration like 1080P monitor playing a 1080P video,
if user use ALT+F4 to exit Movie and TV, there is a chance clocks are
same only water mark changed. Current clock optimization machanism will
result in water mark keeps high after exit Movie and TV app.
[How]
Return if watermark need to be optimized when doing program watermark,
perform the optimization after.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DalMPVisualConfirm does not support FreeSync 2 ARGB2101010 which causes
black visual confirm bar when playing HDR video on FreeSync 2 display in
full screen mode
[How]
Added pink color for DalMPVisualConfirm on FreeSync 2 ARGB2101010
surface
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently DAL programs negative slope for the last point of output
transfer function curve.
[How]
Applying a check for the last PWL point for RGB values not to be
smaller than previous. If smaller, initialize the last point values
to a sum of previous PWL value and previous PWL delta;
Signed-off-by: Vladimir Stempen <vladimir.stempen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Make panel backlight and power on/off functions into
hardware specific function pointers
[How]
Add function pointers for panel related hw functions
- is_panel_powered_on
- is_panel_backlight_on
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
According to HW team, PG is dropped for NV12, but programming
the registers will still cause power to be consumed, so don't
program for NV12.
[How]
Set function pointer to NULL if NV12
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
core_link_read_dpcd() will invoke dm_helpers_dp_read_dpcd(),
which needs to read dpcd info with the help of aconnector.
If aconnector (dc->links[i]->prev) is NULL, then dpcd status
cannot be read.
As a result, dpcd read fails and a line of error will be
printed out in dmesg.log as:
"*ERROR* Failed to found connector for link!"
[How]
Make sure that aconnector (dc->links[i]->prev) is not NULL,
then read dpcd status.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Joseph Gravenor <Joseph.Gravenor@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:
In function dcn10_post_unlock_program_front_end:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2623:29:
warning: variable stream_status set but not used [-Wunused-but-set-variable]
commit bbf5f6c3f8 ("drm/amd/display: Split program front end part that occur outside lock")
involved this unused variable.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
customer issue: found that for their specific panel, EDID register space
being overwritten during SCDC read write
[how]
customer accepted HDMI 2 features not working - disabled SCDC read/write
as well as HDMI 2 in general based on monitor patch
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
in dcn10_apply_ctx_for_surface(), if we hit !top_pipe_to_program,
pipe_ctx->update_flags could not get cleared.
[How]
Moved clearing pipe_ctx->update_flags logic before if
(!top_pipe_to_program) to gurantee pipe_ctx->update_flags get cleared.
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, gcc spews a warning as:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubbub.c: In function ‘hubbub1_verify_allow_pstate_change_high’:
./include/drm/drm_print.h:316:2: warning: ‘debug_data’ may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because the code checks against a static value although it's
basically a constant and guaranteed to be set.
This patch changes the type prefix from static to const for addressing
the compile warning above and also for letting the compiler optimize
better.
Fixes: 62d591a8e0 ("drm/amd/display: create new files for hubbub functions")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
not turning off the mst hub before detection on reboot
causes us to not be able to light up displays with mst hook
[how]
on hw init, see if any displays are lit up. if so, turn them off
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
new HW engine mapping requirment use in PSP
[how]
report stream_enc_inst
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen flickering when HDR switches between FP16 and ARGB2101010
[How]
Moved pipe_control_lock so stream update and plane update occur atomically
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Eventually want to lock at a higher level in stack.
To do this, we need to be able to isolate the parts that need to be done
after pipe unlock.
[How]
Split out programming that is done post unlock.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In current code we're essentially drawing the cursor on every pipe
that contains it. This only works when the planes have the same
scaling for src to dest rect, otherwise we'll get "double cursor" where
one cursor is incorrectly filtered and offset from the real position.
[How]
Without dedicated cursor planes on DCN we require at least one pipe
that matches the scaling of the current timing.
This is an optimization and workaround for the most common case where
the top-most plane is not scaled but the bottom-most plane is scaled.
Whenever a pipe has a parent pipe in the blending tree whose recout
fully contains the current pipe we can disable the pipe.
This only applies when the pipe is actually visible of course.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently if seamless boot is enabled, we will skip double buffer enable
for OTG_BLANK. However, we need the double buffer enable in order to
block global sync signals when OTG becomes blanked (for PSR). Blocking
global sync signals prevent pipe from requesting data.
[How]
Move tg_init before seamless boot check.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With different refresh rate panels, the PSR entry/exit time is
different since it is dependent on 2 frame entry time today
[How]
Make static screen num frame entry time to be calculated
such that entry time is within 30 ms instead of fixed num
frames.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.
[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:482:6-14: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/display/dc/dcn10/dcn10_hw_sequencer.c:485:2-10: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor disappears for some SLS displays that are rotated 180
and 270 degrees. This occurs when there is no pipe split being
done ( ex. 3 or more displays ). The cursor calculations assume
pipe splitting is done so when it calculates the new cursor
position in hwss.set_cursor_position(), it is out-of-bounds so
it disables the cursor in hubp.set_cursor_position().
[How]
In non pipe split cases, calculate cursor using viewport size
( width or height ) instead of viewport size * 2 ( the two
because pipe splitting divides the rectangle into two ).
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain instances, there was a reliance on pipe indexing being accurate. However, this
assumption fails with harvesting of pipes 1 or 2, which can occur in production B6 parts.
HW hang would occur as a result.
[How]
Use hubp index for mpcc, and do mpc_init for all theoretical pipes (including disabled ones).
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. Set second screen only then unplug external monitor
2. Enter to S4 then plug in external monitor
3. Resume from S4, eDP will not turn off when OS set
second screen only
Sometimes OS will not set eDP power up cause eDP dpms_off
keep true then driver skipp disable stream
[How]
When drvier try to disable stream, add link status condition
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
