The STM32H750 is a Cortex-M7 MCU running at 480MHz
and containing 128KBytes internal flash, 1MiB SRAM.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add pin groups for usart3/uart4/spi1/sdmmc2
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add stm32h750-art-pi.dts to support art-pi board
art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm
the detail board information can be found at:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Some instances are missing in current support of stm32h743 MCU. This commit
adds usart3/uart4 and sdmmc2 support.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
This patch is intend to add support stm32h750 value line,
just add stm32h7-pinctrl.dtsi for extending, with following changes:
- rename stm32h743-pinctrl.dtsi to stm32h7-pinctrl.dtsi
- move 'pin-controller' from stm32h7-pinctrl.dtsi to stm32h743.dtsi, to
fix make dtbs_check warrnings
arch/arm/boot/dts/stm32h750i-art-pi.dt.yaml: soc: 'i2c@40005C00',
'i2c@58001C00' do not match any of the regexes:
'@(0|[1-9a-f][0-9a-f]*)$', '^[^@]+$', 'pinctrl-[0-9]+'
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
On the N2100, instead of just marking the r8169 chips as having
broken_parity_status, disable parity error reporting for them entirely.
This was the only relevant place that set broken_parity_status, so we no
longer need to check for it in the r8169 error interrupt handler.
[bhelgaas: squash into one patch, commit log]
Link: https://lore.kernel.org/r/20210330174318.1289680-4-helgaas@kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Although the SMCCC specification provides some limited functionality for
describing the presence of hypervisor and firmware services, this is
generally applicable only to functions designated as "Arm Architecture
Service Functions" and no portable discovery mechanism is provided for
standard hypervisor services, despite having a designated range of
function identifiers reserved by the specification.
In an attempt to avoid the need for additional firmware changes every
time a new function is added, introduce a UID to identify the service
provider as being compatible with KVM. Once this has been established,
additional services can be discovered via a feature bitmap.
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Jianyong Wu <jianyong.wu@arm.com>
[maz: move code to its own file, plug it into PSCI]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201209060932.212364-2-jianyong.wu@arm.com
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for arch/arm/mach-omap1/timer.c follows this syntax, but the
content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: expecting prototype for OMAP1 Dual(). Prototype was for OMAP1610_GPTIMER1_BASE() instead"
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for arch/arm/mach-omap2/omap_twl.c follows this syntax, but the
content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc:
"warning: wrong kernel-doc identifier on line:
* OMAP and TWL PMIC specific initializations."
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Lifu Chen <chenlifu@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on linux-gpio discussion [1], it is best practice to make the
gpio-line-names unique. Generic names like "[ethernet]" are replaced
with the name of the unique signal on the AM3358 SoC ball corresponding
to the gpio line. "[NC]" is also renamed to the standard "NC" name to
represent "not connected".
[1] https://lore.kernel.org/linux-gpio/20201216195357.GA2583366@x1/
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The voltage default on the AB8500 VAUX1 regulator is way
too low and does not correspond to the setting in the
vendor tree. This should be 2.8-3.3 V not 2.5-2.9 V or
things like the HREFP520 touchscreen will not work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting the vmmc supplies is crucial since otherwise the supplying
regulators get disabled and the SD interfaces are no longer powered
which leads to system failures if the system is booted from that SD
interface.
Fixes: 1e44d3f880 ("ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module")
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Due to a hardware bug preventing the correct detection if the ID pin
the USB OTG port cannot be used in otg mode. It can either be set to
host or peripheral. Set it to peripheral so vbus is disabled by default.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinmuxing for the enable pin of the usbh1 node is wrong. It needs to
be muxed as GPIO. While at it, move the pinctrl to the vbus regulator
since it is actually the regulator enable pin.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set Linux default trigger to default on, just like it's normally done
for power LEDs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Partitions are basically fixed indeed but firmware ones don't have
hardcoded function ("firmware" vs "failsafe"). Actual function depends
on bootloader configuration. Use a proper binding for that.
While at it fix numbers formatting to avoid:
arch/arm/boot/dts/bcm47094-linksys-panamera.dt.yaml: partitions: 'partition@1F00000' does not match any of the regexes: '^partition@[0-9a-f]+$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/mtd/partitions/linksys,ns-partitions.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
UBI_GLUEBI is not so common and UBI_FASTMAP is used for several years.
Make them part of a modernization of UBI defconfig options.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Add this board as a module as it's useful for testing audio on multiple
AT91 boards.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
[nicolas.ferre@microchip.com: adap to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Include this driver as the USB-Ethernet chip is present on SAMA5D2-ICP
board.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
[nicolas.ferre@microchip.com: update commit subject and message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Include as built-in as it's used by multiple boards.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
[nicolas.ferre@microchip.com: adap to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
This regulator is needed by several SoC or external peripherals on
different boards, providing required power rails. Make it built-in
to match usual use-cases.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
The reMarkable2 (https://remarkable.com) is an e-ink tablet based on
the imx7d SoC.
This commit is based on the DTS provide by reMarkable but ported to the
latest kernel (instead of 4.14). I have removed references to
non-upstream devices and have changed the UART so that the console can
be accessed without having to open up the device via the OTG pogo pins.
Currently the kernel boots, but there is no support for the display.
WiFi is untested (no display or UART RX makes it hard to test), but
should work with the current upstream driver. As it's untested it's not
included in this commit.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no point in sharing any definitions between
the R2 and R3 versions of the TVK1281618 UIB. The
proximity sensor collides with the touchscreen etc,
it is less confusing to get rid of the overarching
TVK1281618 UIB file and just use one for each.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TC35893 is connected to different GPIOs in different
UIBs so just bite the bullet and push this info down
into respective UIB so we can avoid confusion when
reading the DTS files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull ARM SoC fixes from Arnd Bergmann:
"Too many fixes have accumulated in the soc tree, so this is a fairly
large set. As usual, most of the fixes are for devicetree files, but
there are also notable code changes for imx and omap regressions as
well as some maintainer file updates.
imx:
- Fix an Ethernet issue on imx6ul-14x14-evk board that is caused by
independent PHY reset.
- Add missing `dma-coherent` property for LayerScape device trees to
fix a kernel BUG report.
- Use IRQCHIP_DECLARE for AVIC driver to fix a boot issue on i.MX25
with fw_devlink=on.
- Add missing I2C pinctrl entry for imx8mp-phyboard-pollux-rdk board
to fix the broken I2C GPIO recovery support.
- Add `fsl,use-minimum-ecc` property for imx6ull-myir-mys-6ulx-eval
device tree to fix UBI filesystem mount failure.
at91:
- wrong phy address that blocks Ethernet use on boards with sama5d27
SoM1
- restrictive pin possibilities for sam9x60
omap:
- Fix ocp interconnect bus access error reporting for omap_l3_noc by
setting IRQF_NO_THREAD
- Fix changed mmc slot order regression by adding mmc aliases for
am335x
- Fix dra7 reboot regression caused by invalid pcie reset map
- Fix smartreflex init regression caused by dropped legacy data
- Fix ti-sysc driver warning on unbind if reset is not deasserted
- Fix flakey reset deassert for dra7 iva
stm32:
- MAINTAINER file updates
broadcom:
- brcmstb SoC ID build fix
- MAINTAINER file updates"
* tag 'soc-fixes-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: Add Alain Volmat as STM32 I2C/SMBUS maintainer
MAINTAINERS: Remove Vincent Abriou for STM/STI DRM drivers.
MAINTAINERS: Update some st.com email addresses to foss.st.com
ARM: dts: imx6ull: fix ubi filesystem mount failed
ARM: imx6ul-14x14-evk: Do not reset the Ethernet PHYs independently
arm64: dts: imx8mp-phyboard-pollux-rdk: Add missing pinctrl entry
arm64: dts: ls1012a: mark crypto engine dma coherent
arm64: dts: ls1043a: mark crypto engine dma coherent
arm64: dts: ls1046a: mark crypto engine dma coherent
ARM: imx: avic: Convert to using IRQCHIP_DECLARE
ARM: dts: at91: sam9x60: fix mux-mask to match product's datasheet
ARM: dts: at91: sam9x60: fix mux-mask for PA7 so it can be set to A, B and C
ARM: dts: at91-sama5d27_som1: fix phy address to 7
soc: ti: omap-prm: Fix occasional abort on reset deassert for dra7 iva
bus: ti-sysc: Fix warning on unbind if reset is not deasserted
ARM: OMAP2+: Fix smartreflex init regression after dropping legacy data
soc: ti: omap-prm: Fix reboot issue with invalid pcie reset map for dra7
MAINTAINERS: rectify BROADCOM PMB (POWER MANAGEMENT BUS) DRIVER
ARM: dts: am33xx: add aliases for mmc interfaces
bus: omap_l3_noc: mark l3 irqs as IRQF_NO_THREAD
Acer A500 uses Atmel Maxtouch 1386 touchscreen controller. This controller
has WAKE line which could be connected to I2C clock lane, dedicated GPIO
or fixed to HIGH level. Controller wakes up from a deep sleep when WAKE
line is asserted low. Acer A500 has WAKE line connected to I2C clock and
Linux device driver doesn't work property without knowing what wakeup
method is used by h/w.
Add atmel,wakeup-method property to the touchscreen node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[treding@nvidia.com: use literal to avoid dependency on header file]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The TVK1281618 R3 sensors are different from the R2 board,
some incorrectness is fixed and some new sensors added, we
also rename the nodes appropriately with accelerometer@
etc.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These sensors are particular to the TVK UIB R2 board and
will conflict with the R3 board, so push them down to
the actual UIB include DTSI.
Rename the nodes appropriately to accelerometer@ etc
in the process.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Synaptics RMI4 touchscreen is a property of the
TVK1281618 R2 UIB, so move it into that file instead
of the main TVK1281618 main include so we can define
another touchscreen for the R3 UIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The touchscreen is mounted with flipped x/y on the R2
version of TVK1281618. Push this setting to that DTS file
only.
The function nodes were named wrong so the OF properties
didn not "take". Fix the node names from "rmi-fnn" to
"rmi4-nn" so this also work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO215 has a rail named WLAN_RST_N but it is actually connected
to the pin WLAN_REG_ON on the BCM4330 chip, so this should be
the WLAN regulator GPIO rather than GPIO222. The misunderstanding
comes from the erroneous naming of the rail on the schematic.
GPIO222 is indeed connected to the rail BT_VREG_EN and the pin
BT_REG_ON, and can be handled by the driver as usual.
This corrects misunderstandings and makes Janice's WLAN and BT
setup look like that of Golden and Skomer.
Add explicit BCM4330 compatible to the WLAN chip.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
This fixes warnings/errors like:
arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dt.yaml: /: memory@0:reg:0: [0, 134217728, 2281701376, 402653184] is too long
From schema: /lib/python3.6/site-packages/dtschema/schemas/reg.yaml
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Many architectures duplicate similar shell scripts.
This commit converts ARM to use scripts/syscallhdr.sh, and also
collects OABI/OEBI syscalls into unistd-eabi.h/unistd-oabi.h,
removing unistd-common.h.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
