This is exactly the same as the arm64 version, which I recently copied
into lib/ for use by the RISC-V port.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Now that ARM started following the example of arm64 and RISC-V, and
no longer imposes any restrictions on the placement of the FDT in
memory at boot, we no longer need per-arch implementations of
efi_get_max_fdt_addr() to factor out the differences. So get rid of
it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Link: https://lore.kernel.org/r/20201029134901.9773-1-ardb@kernel.org
Now that we reduced the minimum relative alignment between PHYS_OFFSET
and PAGE_OFFSET to 2 MiB, we can take this into account when allocating
memory for the decompressed kernel when booting via EFI. This minimizes
the amount of unusable memory we may end up with due to the base of DRAM
being occupied by firmware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Scatter-gather lists passed to UpdateCapsule() should be cleaned
from the D-cache to ensure that they are visible to the CPU after a
warm reboot before the MMU is enabled. On ARM and arm64 systems, this
implies a D-cache clean by virtual address to the point of coherency.
However, due to the fact that the firmware itself is not able to map
physical addresses back to virtual addresses when running under the OS,
this must be done by the caller.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The ARM version of __div64_32() encapsulates a call to __do_div64 with
non-standard argument passing. In particular, __n is a 64-bit input
argument assigned to r0-r1 and __rem is an output argument sharing half
of that r0-r1 register pair.
With __n being an input argument, the compiler is in its right to
presume that r0-r1 would still hold the value of __n past the inline
assembly statement. Normally, the compiler would have assigned non
overlapping registers to __n and __rem if the value for __n is needed
again.
However, here we enforce our own register assignment and gcc fails to
notice the conflict. In practice this doesn't cause any problem as __n
is considered dead after the asm statement and *n is overwritten.
However this is not always guaranteed and clang rightfully complains.
Let's fix it properly by making __n into an input-output variable. This
makes it clear that those registers representing __n have been modified.
Then we can extract __rem as the high part of __n with plain C code.
This asm constraint "abuse" was likely relied upon back when gcc didn't
handle 64-bit values optimally. Turns out that gcc is now able to
optimize things and produces the same code with this patch applied.
Reported-by: Antony Yu <swpenim@gmail.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The reference to cache_is_vivt() was moved into a header file,
which now causes a build failure in rare randconfig builds:
arch/arm/include/asm/highmem.h:52:43: error: implicit declaration of function 'cache_is_vivt' [-Werror,-Wimplicit-function-declaration]
Add an explicit include to make it build reliably.
Fixes: 2a15ba82fa ("ARM: highmem: Switch to generic kmap atomic")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20201204165930.3877571-1-arnd@kernel.org
This is a single bugfix for a bug that Stefan Agner found on 32-bit
Arm, but that exists on several other architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=xgYa
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fix from Arnd Bergmann:
"Add correct MAX_POSSIBLE_PHYSMEM_BITS setting to asm-generic.
This is a single bugfix for a bug that Stefan Agner found on 32-bit
Arm, but that exists on several other architectures"
* tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: pgtable: define MAX_POSSIBLE_PHYSMEM_BITS where needed
Previously we were not clearing non-uapi flag bits in
sigaction.sa_flags when storing the userspace-provided sa_flags or
when returning them via oldact. Start doing so.
This allows userspace to detect missing support for flag bits and
allows the kernel to use non-uapi bits internally, as we are already
doing in arch/x86 for two flag bits. Now that this change is in
place, we no longer need the code in arch/x86 that was hiding these
bits from userspace, so remove it.
This is technically a userspace-visible behavior change for sigaction, as
the unknown bits returned via oldact.sa_flags are no longer set. However,
we are free to define the behavior for unknown bits exactly because
their behavior is currently undefined, so for now we can define the
meaning of each of them to be "clear the bit in oldact.sa_flags unless
the bit becomes known in the future". Furthermore, this behavior is
consistent with OpenBSD [1], illumos [2] and XNU [3] (FreeBSD [4] and
NetBSD [5] fail the syscall if unknown bits are set). So there is some
precedent for this behavior in other kernels, and in particular in XNU,
which is probably the most popular kernel among those that I looked at,
which means that this change is less likely to be a compatibility issue.
Link: [1] f634a6a4b5/sys/kern/kern_sig.c (L278)
Link: [2] 76f19f5fdc/usr/src/uts/common/syscall/sigaction.c (L86)
Link: [3] a449c6a3b8/bsd/kern/kern_sig.c (L480)
Link: [4] eded70c370/sys/kern/kern_sig.c (L699)
Link: [5] 3365779bec/sys/kern/sys_sig.c (L473)
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Link: https://linux-review.googlesource.com/id/I35aab6f5be932505d90f3b3450c083b4db1eca86
Link: https://lkml.kernel.org/r/878dbcb5f47bc9b11881c81f745c0bef5c23f97f.1605235762.git.pcc@google.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Most architectures with the exception of alpha, mips, parisc and
sparc use the same values for these flags. Move their definitions into
asm-generic/signal-defs.h and allow the architectures with non-standard
values to override them. Also, document the non-standard flag values
in order to make it easier to add new generic flags in the future.
A consequence of this change is that on powerpc and x86, the constants'
values aside from SA_RESETHAND change signedness from unsigned
to signed. This is not expected to impact realistic use of these
constants. In particular the typical use of the constants where they
are or'ed together and assigned to sa_flags (or another int variable)
would not be affected.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Link: https://linux-review.googlesource.com/id/Ia3849f18b8009bf41faca374e701cdca36974528
Link: https://lkml.kernel.org/r/b6d0d1ec34f9ee93e1105f14f288fba5f89d1f24.1605235762.git.pcc@google.com
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
irq_cpustat_t is exactly the same as the asm-generic one. Define
ack_bad_irq so the generic header does not emit the generic version of it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20201113141733.276505871@linutronix.de
To enable seccomp constant action bitmaps, we need to have a static
mapping to the audit architecture and system call table size. Add these
for arm.
Signed-off-by: Kees Cook <keescook@chromium.org>
Stefan Agner reported a bug when using zsram on 32-bit Arm machines
with RAM above the 4GB address boundary:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = a27bd01c
[00000000] *pgd=236a0003, *pmd=1ffa64003
Internal error: Oops: 207 [#1] SMP ARM
Modules linked in: mdio_bcm_unimac(+) brcmfmac cfg80211 brcmutil raspberrypi_hwmon hci_uart crc32_arm_ce bcm2711_thermal phy_generic genet
CPU: 0 PID: 123 Comm: mkfs.ext4 Not tainted 5.9.6 #1
Hardware name: BCM2711
PC is at zs_map_object+0x94/0x338
LR is at zram_bvec_rw.constprop.0+0x330/0xa64
pc : [<c0602b38>] lr : [<c0bda6a0>] psr: 60000013
sp : e376bbe0 ip : 00000000 fp : c1e2921c
r10: 00000002 r9 : c1dda730 r8 : 00000000
r7 : e8ff7a00 r6 : 00000000 r5 : 02f9ffa0 r4 : e3710000
r3 : 000fdffe r2 : c1e0ce80 r1 : ebf979a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5383d Table: 235c2a80 DAC: fffffffd
Process mkfs.ext4 (pid: 123, stack limit = 0x495a22e6)
Stack: (0xe376bbe0 to 0xe376c000)
As it turns out, zsram needs to know the maximum memory size, which
is defined in MAX_PHYSMEM_BITS when CONFIG_SPARSEMEM is set, or in
MAX_POSSIBLE_PHYSMEM_BITS on the x86 architecture.
The same problem will be hit on all 32-bit architectures that have a
physical address space larger than 4GB and happen to not enable sparsemem
and include asm/sparsemem.h from asm/pgtable.h.
After the initial discussion, I suggested just always defining
MAX_POSSIBLE_PHYSMEM_BITS whenever CONFIG_PHYS_ADDR_T_64BIT is
set, or provoking a build error otherwise. This addresses all
configurations that can currently have this runtime bug, but
leaves all other configurations unchanged.
I looked up the possible number of bits in source code and
datasheets, here is what I found:
- on ARC, CONFIG_ARC_HAS_PAE40 controls whether 32 or 40 bits are used
- on ARM, CONFIG_LPAE enables 40 bit addressing, without it we never
support more than 32 bits, even though supersections in theory allow
up to 40 bits as well.
- on MIPS, some MIPS32r1 or later chips support 36 bits, and MIPS32r5
XPA supports up to 60 bits in theory, but 40 bits are more than
anyone will ever ship
- On PowerPC, there are three different implementations of 36 bit
addressing, but 32-bit is used without CONFIG_PTE_64BIT
- On RISC-V, the normal page table format can support 34 bit
addressing. There is no highmem support on RISC-V, so anything
above 2GB is unused, but it might be useful to eventually support
CONFIG_ZRAM for high pages.
Fixes: 61989a80fb ("staging: zsmalloc: zsmalloc memory allocation library")
Fixes: 02390b87a9 ("mm/zsmalloc: Prepare to variable MAX_PHYSMEM_BITS")
Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Link: https://lore.kernel.org/linux-mm/bdfa44bf1c570b05d6c70898e2bbb0acf234ecdf.1604762181.git.stefan@agner.ch/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Wire up TIF_NOTIFY_SIGNAL handling for arm.
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
rpc is the only user of the timer_tick() function now, and can
just call the newly added generic version instead.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, the .alt.smp.init section contains the virtual addresses
of the patch sites. Since patching may occur both before and after
switching into virtual mode, this requires some manual handling of
the address when applying the UP alternative.
Let's simplify this by using relative offsets in the table entries:
this allows us to simply add each entry's address to its contents,
regardless of whether we are running in virtual mode or not.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The ARM kernel's linear map starts at PAGE_OFFSET, which maps to a
physical address (PHYS_OFFSET) that is platform specific, and is
discovered at boot. Since we don't want to slow down translations
between physical and virtual addresses by keeping the offset in a
variable in memory, we implement this by patching the code performing
the translation, and putting the offset between PAGE_OFFSET and the
start of physical RAM directly into the instruction opcodes.
As we only patch up to 8 bits of offset, yielding 4 GiB >> 8 == 16 MiB
of granularity, we have to round up PHYS_OFFSET to the next multiple if
the start of physical RAM is not a multiple of 16 MiB. This wastes some
physical RAM, since the memory that was skipped will now live below
PAGE_OFFSET, making it inaccessible to the kernel.
We can improve this by changing the patchable sequences and the patching
logic to carry more bits of offset: 11 bits gives us 4 GiB >> 11 == 2 MiB
of granularity, and so we will never waste more than that amount by
rounding up the physical start of DRAM to the next multiple of 2 MiB.
(Note that 2 MiB granularity guarantees that the linear mapping can be
created efficiently, whereas less than 2 MiB may result in the linear
mapping needing another level of page tables)
This helps Zhen Lei's scenario, where the start of DRAM is known to be
occupied. It also helps EFI boot, which relies on the firmware's page
allocator to allocate space for the decompressed kernel as low as
possible. And if the KASLR patches ever land for 32-bit, it will give
us 3 more bits of randomization of the placement of the kernel inside
the linear region.
For the ARM code path, it simply comes down to using two add/sub
instructions instead of one for the carryless version, and patching
each of them with the correct immediate depending on the rotation
field. For the LPAE calculation, which has to deal with a carry, it
patches the MOVW instruction with up to 12 bits of offset (but we only
need 11 bits anyway)
For the Thumb2 code path, patching more than 11 bits of displacement
would be somewhat cumbersome, but the 11 bits we need fit nicely into
the second word of the u16[2] opcode, so we simply update the immediate
assignment and the left shift to create an addend of the right magnitude.
Suggested-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
In preparation for reducing the phys-to-virt minimum relative alignment
from 16 MiB to 2 MiB, switch to patchable sequences involving MOVW
instructions that can more easily be manipulated to carry a 12-bit
immediate. Note that the non-LPAE ARM sequence is not updated: MOVW
may not be supported on non-LPAE platforms, and the sequence itself
can be updated more easily to apply the 12 bits of displacement.
For Thumb2, which has many more versions of opcodes, switch to a sequence
that can be patched by the same patching code for both versions. Note
that the Thumb2 opcodes for MOVW and MVN are unambiguous, and have no
rotation bits in their immediate fields, so there is no need to use
placeholder constants in the asm blocks.
While at it, drop the 'volatile' qualifiers from the asm blocks: the
code does not have any side effects that are invisible to the compiler,
so it is free to omit these sequences if the outputs are not used.
Suggested-by: Russell King <linux@armlinux.org.uk>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Free up a register in the p2v patching code by switching to relative
references, which don't require keeping the phys-to-virt displacement
live in a register.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
We always pass the same value for 'type' so pull it into the __pv_stub
macro itself.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
When using the new adr_l/ldr_l/str_l macros to refer to external symbols
from modules, the linker may emit place relative ELF relocations that
need to be fixed up by the module loader. So add support for these.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Like arm64, ARM supports position independent code sequences that
produce symbol references with a greater reach than the ordinary
adr/ldr instructions. Since on ARM, the adrl pseudo-instruction is
only supported in ARM mode (and not at all when using Clang), having
a adr_l macro like we do on arm64 is useful, and increases symmetry
as well.
Currently, we use open coded instruction sequences involving literals
and arithmetic operations. Instead, we can use movw/movt pairs on v7
CPUs, circumventing the D-cache entirely.
E.g., on v7+ CPUs, we can emit a PC-relative reference as follows:
movw <reg>, #:lower16:<sym> - (1f + 8)
movt <reg>, #:upper16:<sym> - (1f + 8)
1: add <reg>, <reg>, pc
For older CPUs, we can emit the literal into a subsection, allowing it
to be emitted out of line while retaining the ability to perform
arithmetic on label offsets.
E.g., on pre-v7 CPUs, we can emit a PC-relative reference as follows:
ldr <reg>, 2f
1: add <reg>, <reg>, pc
.subsection 1
2: .long <sym> - (1b + 8)
.previous
This is allowed by the assembler because, unlike ordinary sections,
subsections are combined into a single section in the object file, and
so the label references are not true cross-section references that are
visible as relocations. (Subsections have been available in binutils
since 2004 at least, so they should not cause any issues with older
toolchains.)
So use the above to implement the macros mov_l, adr_l, ldr_l and str_l,
all of which will use movw/movt pairs on v7 and later CPUs, and use
PC-relative literals otherwise.
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Commit
149a3ffe62b9dbc3 ("9012/1: move device tree mapping out of linear region")
created a permanent, read-only section mapping of the device tree blob
provided by the firmware, and added a set of macros to get the base and
size of the virtually mapped FDT based on the physical address. However,
while the mapping code uses the SECTION_SIZE macro correctly, the macros
use PMD_SIZE instead, which means something entirely different on ARM when
using short descriptors, and is therefore not the right quantity to use
here. So replace PMD_SIZE with SECTION_SIZE. While at it, change the names
of the macro and its parameter to clarify that it returns the virtual
address of the start of the FDT, based on the physical address in memory.
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch initializes KASan shadow region's page table and memory.
There are two stage for KASan initializing:
1. At early boot stage the whole shadow region is mapped to just
one physical page (kasan_zero_page). It is finished by the function
kasan_early_init which is called by __mmap_switched(arch/arm/kernel/
head-common.S)
2. After the calling of paging_init, we use kasan_zero_page as zero
shadow for some memory that KASan does not need to track, and we
allocate a new shadow space for the other memory that KASan need to
track. These issues are finished by the function kasan_init which is
call by setup_arch.
When using KASan we also need to increase the THREAD_SIZE_ORDER
from 1 to 2 as the extra calls for shadow memory uses quite a bit
of stack.
As we need to make a temporary copy of the PGD when setting up
shadow memory we create a helpful PGD_SIZE definition for both
LPAE and non-LPAE setups.
The KASan core code unconditionally calls pud_populate() so this
needs to be changed from BUG() to do {} while (0) when building
with KASan enabled.
After the initial development by Andre Ryabinin several modifications
have been made to this code:
Abbott Liu <liuwenliang@huawei.com>
- Add support ARM LPAE: If LPAE is enabled, KASan shadow region's
mapping table need be copied in the pgd_alloc() function.
- Change kasan_pte_populate,kasan_pmd_populate,kasan_pud_populate,
kasan_pgd_populate from .meminit.text section to .init.text section.
Reported by Florian Fainelli <f.fainelli@gmail.com>
Linus Walleij <linus.walleij@linaro.org>:
- Drop the custom mainpulation of TTBR0 and just use
cpu_switch_mm() to switch the pgd table.
- Adopt to handle 4th level page tabel folding.
- Rewrite the entire page directory and page entry initialization
sequence to be recursive based on ARM64:s kasan_init.c.
Ard Biesheuvel <ardb@kernel.org>:
- Necessary underlying fixes.
- Crucial bug fixes to the memory set-up code.
Co-developed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Co-developed-by: Abbott Liu <liuwenliang@huawei.com>
Co-developed-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: kasan-dev@googlegroups.com
Cc: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org> # QEMU/KVM/mach-virt/LPAE/8G
Tested-by: Florian Fainelli <f.fainelli@gmail.com> # Brahma SoCs
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # i.MX6Q
Reported-by: Russell King - ARM Linux <rmk+kernel@armlinux.org.uk>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Abbott Liu <liuwenliang@huawei.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Define KASAN_SHADOW_OFFSET,KASAN_SHADOW_START and KASAN_SHADOW_END for
the Arm kernel address sanitizer. We are "stealing" lowmem (the 4GB
addressable by a 32bit architecture) out of the virtual address
space to use as shadow memory for KASan as follows:
+----+ 0xffffffff
| |
| | |-> Static kernel image (vmlinux) BSS and page table
| |/
+----+ PAGE_OFFSET
| |
| | |-> Loadable kernel modules virtual address space area
| |/
+----+ MODULES_VADDR = KASAN_SHADOW_END
| |
| | |-> The shadow area of kernel virtual address.
| |/
+----+-> TASK_SIZE (start of kernel space) = KASAN_SHADOW_START the
| | shadow address of MODULES_VADDR
| | |
| | |
| | |-> The user space area in lowmem. The kernel address
| | | sanitizer do not use this space, nor does it map it.
| | |
| | |
| | |
| | |
| |/
------ 0
0 .. TASK_SIZE is the memory that can be used by shared
userspace/kernelspace. It us used for userspace processes and for
passing parameters and memory buffers in system calls etc. We do not
need to shadow this area.
KASAN_SHADOW_START:
This value begins with the MODULE_VADDR's shadow address. It is the
start of kernel virtual space. Since we have modules to load, we need
to cover also that area with shadow memory so we can find memory
bugs in modules.
KASAN_SHADOW_END
This value is the 0x100000000's shadow address: the mapping that would
be after the end of the kernel memory at 0xffffffff. It is the end of
kernel address sanitizer shadow area. It is also the start of the
module area.
KASAN_SHADOW_OFFSET:
This value is used to map an address to the corresponding shadow
address by the following formula:
shadow_addr = (address >> 3) + KASAN_SHADOW_OFFSET;
As you would expect, >> 3 is equal to dividing by 8, meaning each
byte in the shadow memory covers 8 bytes of kernel memory, so one
bit shadow memory per byte of kernel memory is used.
The KASAN_SHADOW_OFFSET is provided in a Kconfig option depending
on the VMSPLIT layout of the system: the kernel and userspace can
split up lowmem in different ways according to needs, so we calculate
the shadow offset depending on this.
When kasan is enabled, the definition of TASK_SIZE is not an 8-bit
rotated constant, so we need to modify the TASK_SIZE access code in the
*.s file.
The kernel and modules may use different amounts of memory,
according to the VMSPLIT configuration, which in turn
determines the PAGE_OFFSET.
We use the following KASAN_SHADOW_OFFSETs depending on how the
virtual memory is split up:
- 0x1f000000 if we have 1G userspace / 3G kernelspace split:
- The kernel address space is 3G (0xc0000000)
- PAGE_OFFSET is then set to 0x40000000 so the kernel static
image (vmlinux) uses addresses 0x40000000 .. 0xffffffff
- On top of that we have the MODULES_VADDR which under
the worst case (using ARM instructions) is
PAGE_OFFSET - 16M (0x01000000) = 0x3f000000
so the modules use addresses 0x3f000000 .. 0x3fffffff
- So the addresses 0x3f000000 .. 0xffffffff need to be
covered with shadow memory. That is 0xc1000000 bytes
of memory.
- 1/8 of that is needed for its shadow memory, so
0x18200000 bytes of shadow memory is needed. We
"steal" that from the remaining lowmem.
- The KASAN_SHADOW_START becomes 0x26e00000, to
KASAN_SHADOW_END at 0x3effffff.
- Now we can calculate the KASAN_SHADOW_OFFSET for any
kernel address as 0x3f000000 needs to map to the first
byte of shadow memory and 0xffffffff needs to map to
the last byte of shadow memory. Since:
SHADOW_ADDR = (address >> 3) + KASAN_SHADOW_OFFSET
0x26e00000 = (0x3f000000 >> 3) + KASAN_SHADOW_OFFSET
KASAN_SHADOW_OFFSET = 0x26e00000 - (0x3f000000 >> 3)
KASAN_SHADOW_OFFSET = 0x26e00000 - 0x07e00000
KASAN_SHADOW_OFFSET = 0x1f000000
- 0x5f000000 if we have 2G userspace / 2G kernelspace split:
- The kernel space is 2G (0x80000000)
- PAGE_OFFSET is set to 0x80000000 so the kernel static
image uses 0x80000000 .. 0xffffffff.
- On top of that we have the MODULES_VADDR which under
the worst case (using ARM instructions) is
PAGE_OFFSET - 16M (0x01000000) = 0x7f000000
so the modules use addresses 0x7f000000 .. 0x7fffffff
- So the addresses 0x7f000000 .. 0xffffffff need to be
covered with shadow memory. That is 0x81000000 bytes
of memory.
- 1/8 of that is needed for its shadow memory, so
0x10200000 bytes of shadow memory is needed. We
"steal" that from the remaining lowmem.
- The KASAN_SHADOW_START becomes 0x6ee00000, to
KASAN_SHADOW_END at 0x7effffff.
- Now we can calculate the KASAN_SHADOW_OFFSET for any
kernel address as 0x7f000000 needs to map to the first
byte of shadow memory and 0xffffffff needs to map to
the last byte of shadow memory. Since:
SHADOW_ADDR = (address >> 3) + KASAN_SHADOW_OFFSET
0x6ee00000 = (0x7f000000 >> 3) + KASAN_SHADOW_OFFSET
KASAN_SHADOW_OFFSET = 0x6ee00000 - (0x7f000000 >> 3)
KASAN_SHADOW_OFFSET = 0x6ee00000 - 0x0fe00000
KASAN_SHADOW_OFFSET = 0x5f000000
- 0x9f000000 if we have 3G userspace / 1G kernelspace split,
and this is the default split for ARM:
- The kernel address space is 1GB (0x40000000)
- PAGE_OFFSET is set to 0xc0000000 so the kernel static
image uses 0xc0000000 .. 0xffffffff.
- On top of that we have the MODULES_VADDR which under
the worst case (using ARM instructions) is
PAGE_OFFSET - 16M (0x01000000) = 0xbf000000
so the modules use addresses 0xbf000000 .. 0xbfffffff
- So the addresses 0xbf000000 .. 0xffffffff need to be
covered with shadow memory. That is 0x41000000 bytes
of memory.
- 1/8 of that is needed for its shadow memory, so
0x08200000 bytes of shadow memory is needed. We
"steal" that from the remaining lowmem.
- The KASAN_SHADOW_START becomes 0xb6e00000, to
KASAN_SHADOW_END at 0xbfffffff.
- Now we can calculate the KASAN_SHADOW_OFFSET for any
kernel address as 0xbf000000 needs to map to the first
byte of shadow memory and 0xffffffff needs to map to
the last byte of shadow memory. Since:
SHADOW_ADDR = (address >> 3) + KASAN_SHADOW_OFFSET
0xb6e00000 = (0xbf000000 >> 3) + KASAN_SHADOW_OFFSET
KASAN_SHADOW_OFFSET = 0xb6e00000 - (0xbf000000 >> 3)
KASAN_SHADOW_OFFSET = 0xb6e00000 - 0x17e00000
KASAN_SHADOW_OFFSET = 0x9f000000
- 0x8f000000 if we have 3G userspace / 1G kernelspace with
full 1 GB low memory (VMSPLIT_3G_OPT):
- The kernel address space is 1GB (0x40000000)
- PAGE_OFFSET is set to 0xb0000000 so the kernel static
image uses 0xb0000000 .. 0xffffffff.
- On top of that we have the MODULES_VADDR which under
the worst case (using ARM instructions) is
PAGE_OFFSET - 16M (0x01000000) = 0xaf000000
so the modules use addresses 0xaf000000 .. 0xaffffff
- So the addresses 0xaf000000 .. 0xffffffff need to be
covered with shadow memory. That is 0x51000000 bytes
of memory.
- 1/8 of that is needed for its shadow memory, so
0x0a200000 bytes of shadow memory is needed. We
"steal" that from the remaining lowmem.
- The KASAN_SHADOW_START becomes 0xa4e00000, to
KASAN_SHADOW_END at 0xaeffffff.
- Now we can calculate the KASAN_SHADOW_OFFSET for any
kernel address as 0xaf000000 needs to map to the first
byte of shadow memory and 0xffffffff needs to map to
the last byte of shadow memory. Since:
SHADOW_ADDR = (address >> 3) + KASAN_SHADOW_OFFSET
0xa4e00000 = (0xaf000000 >> 3) + KASAN_SHADOW_OFFSET
KASAN_SHADOW_OFFSET = 0xa4e00000 - (0xaf000000 >> 3)
KASAN_SHADOW_OFFSET = 0xa4e00000 - 0x15e00000
KASAN_SHADOW_OFFSET = 0x8f000000
- The default value of 0xffffffff for KASAN_SHADOW_OFFSET
is an error value. We should always match one of the
above shadow offsets.
When we do this, TASK_SIZE will sometimes get a bit odd values
that will not fit into immediate mov assembly instructions.
To account for this, we need to rewrite some assembly using
TASK_SIZE like this:
- mov r1, #TASK_SIZE
+ ldr r1, =TASK_SIZE
or
- cmp r4, #TASK_SIZE
+ ldr r0, =TASK_SIZE
+ cmp r4, r0
this is done to avoid the immediate #TASK_SIZE that need to
fit into a limited number of bits.
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: kasan-dev@googlegroups.com
Cc: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org> # QEMU/KVM/mach-virt/LPAE/8G
Tested-by: Florian Fainelli <f.fainelli@gmail.com> # Brahma SoCs
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # i.MX6Q
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Abbott Liu <liuwenliang@huawei.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Functions like memset()/memmove()/memcpy() do a lot of memory
accesses.
If a bad pointer is passed to one of these functions it is important
to catch this. Compiler instrumentation cannot do this since these
functions are written in assembly.
KASan replaces these memory functions with instrumented variants.
The original functions are declared as weak symbols so that
the strong definitions in mm/kasan/kasan.c can replace them.
The original functions have aliases with a '__' prefix in their
name, so we can call the non-instrumented variant if needed.
We must use __memcpy()/__memset() in place of memcpy()/memset()
when we copy .data to RAM and when we clear .bss, because
kasan_early_init cannot be called before the initialization of
.data and .bss.
For the kernel compression and EFI libstub's custom string
libraries we need a special quirk: even if these are built
without KASan enabled, they rely on the global headers for their
custom string libraries, which means that e.g. memcpy()
will be defined to __memcpy() and we get link failures.
Since these implementations are written i C rather than
assembly we use e.g. __alias(memcpy) to redirected any
users back to the local implementation.
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: kasan-dev@googlegroups.com
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org> # QEMU/KVM/mach-virt/LPAE/8G
Tested-by: Florian Fainelli <f.fainelli@gmail.com> # Brahma SoCs
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # i.MX6Q
Reported-by: Russell King - ARM Linux <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abbott Liu <liuwenliang@huawei.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
On ARM, setting up the linear region is tricky, given the constraints
around placement and alignment of the memblocks, and how the kernel
itself as well as the DT are placed in physical memory.
Let's simplify matters a bit, by moving the device tree mapping to the
top of the address space, right between the end of the vmalloc region
and the start of the the fixmap region, and create a read-only mapping
for it that is independent of the size of the linear region, and how it
is organized.
Since this region was formerly used as a guard region, which will now be
populated fully on LPAE builds by this read-only mapping (which will
still be able to function as a guard region for stray writes), bump the
start of the [underutilized] fixmap region by 512 KB as well, to ensure
that there is always a proper guard region here. Doing so still leaves
ample room for the fixmap space, even with NR_CPUS set to its maximum
value of 32.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Before moving the DT mapping out of the linear region, let's prepare
for this change by removing all the phys-to-virt translations of the
__atags_pointer variable, and perform this translation only once at
setup time.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
- Support 'make compile_commands.json' to generate the compilation
database more easily, avoiding stale entries
- Support 'make clang-analyzer' and 'make clang-tidy' for static checks
using clang-tidy
- Preprocess scripts/modules.lds.S to allow CONFIG options in the module
linker script
- Drop cc-option tests from compiler flags supported by our minimal
GCC/Clang versions
- Use always 12-digits commit hash for CONFIG_LOCALVERSION_AUTO=y
- Use sha1 build id for both BFD linker and LLD
- Improve deb-pkg for reproducible builds and rootless builds
- Remove stale, useless scripts/namespace.pl
- Turn -Wreturn-type warning into error
- Fix build error of deb-pkg when CONFIG_MODULES=n
- Replace 'hostname' command with more portable 'uname -n'
- Various Makefile cleanups
-----BEGIN PGP SIGNATURE-----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=tZRN
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Support 'make compile_commands.json' to generate the compilation
database more easily, avoiding stale entries
- Support 'make clang-analyzer' and 'make clang-tidy' for static checks
using clang-tidy
- Preprocess scripts/modules.lds.S to allow CONFIG options in the
module linker script
- Drop cc-option tests from compiler flags supported by our minimal
GCC/Clang versions
- Use always 12-digits commit hash for CONFIG_LOCALVERSION_AUTO=y
- Use sha1 build id for both BFD linker and LLD
- Improve deb-pkg for reproducible builds and rootless builds
- Remove stale, useless scripts/namespace.pl
- Turn -Wreturn-type warning into error
- Fix build error of deb-pkg when CONFIG_MODULES=n
- Replace 'hostname' command with more portable 'uname -n'
- Various Makefile cleanups
* tag 'kbuild-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
kbuild: Use uname for LINUX_COMPILE_HOST detection
kbuild: Only add -fno-var-tracking-assignments for old GCC versions
kbuild: remove leftover comment for filechk utility
treewide: remove DISABLE_LTO
kbuild: deb-pkg: clean up package name variables
kbuild: deb-pkg: do not build linux-headers package if CONFIG_MODULES=n
kbuild: enforce -Werror=return-type
scripts: remove namespace.pl
builddeb: Add support for all required debian/rules targets
builddeb: Enable rootless builds
builddeb: Pass -n to gzip for reproducible packages
kbuild: split the build log of kallsyms
kbuild: explicitly specify the build id style
scripts/setlocalversion: make git describe output more reliable
kbuild: remove cc-option test of -Werror=date-time
kbuild: remove cc-option test of -fno-stack-check
kbuild: remove cc-option test of -fno-strict-overflow
kbuild: move CFLAGS_{KASAN,UBSAN,KCSAN} exports to relevant Makefiles
kbuild: remove redundant CONFIG_KASAN check from scripts/Makefile.kasan
kbuild: do not create built-in objects for external module builds
...
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----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=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
- Rework cpufreq statistics collection to allow it to take place
when fast frequency switching is enabled in the governor (Viresh
Kumar).
- Make the cpufreq core set the frequency scale on behalf of the
driver and update several cpufreq drivers accordingly (Ionela
Voinescu, Valentin Schneider).
- Add new hardware support to the STI and qcom cpufreq drivers and
improve them (Alain Volmat, Manivannan Sadhasivam).
- Fix multiple assorted issues in cpufreq drivers (Jon Hunter,
Krzysztof Kozlowski, Matthias Kaehlcke, Pali Rohár, Stephan
Gerhold, Viresh Kumar).
- Fix several assorted issues in the operating performance points
(OPP) framework (Stephan Gerhold, Viresh Kumar).
- Allow devfreq drivers to fetch devfreq instances by DT enumeration
instead of using explicit phandles and modify the devfreq core
code to support driver-specific devfreq DT bindings (Leonard
Crestez, Chanwoo Choi).
- Improve initial hardware resetting in the tegra30 devfreq driver
and clean up the tegra cpuidle driver (Dmitry Osipenko).
- Update the cpuidle core to collect state entry rejection
statistics and expose them via sysfs (Lina Iyer).
- Improve the ACPI _CST code handling diagnostics (Chen Yu).
- Update the PSCI cpuidle driver to allow the PM domain
initialization to occur in the OSI mode as well as in the PC
mode (Ulf Hansson).
- Rework the generic power domains (genpd) core code to allow
domain power off transition to be aborted in the absence of the
"power off" domain callback (Ulf Hansson).
- Fix two suspend-to-idle issues in the ACPI EC driver (Rafael
Wysocki).
- Fix the handling of timer_expires in the PM-runtime framework on
32-bit systems and the handling of device links in it (Grygorii
Strashko, Xiang Chen).
- Add IO requests batching support to the hibernate image saving and
reading code and drop a bogus get_gendisk() from there (Xiaoyi
Chen, Christoph Hellwig).
- Allow PCIe ports to be put into the D3cold power state if they
are power-manageable via ACPI (Lukas Wunner).
- Add missing header file include to a power capping driver (Pujin
Shi).
- Clean up the qcom-cpr AVS driver a bit (Liu Shixin).
- Kevin Hilman steps down as designated reviwer of adaptive voltage
scaling (AVS) driverrs (Kevin Hilman).
-----BEGIN PGP SIGNATURE-----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=rGhy
-----END PGP SIGNATURE-----
Merge tag 'pm-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These rework the collection of cpufreq statistics to allow it to take
place if fast frequency switching is enabled in the governor, rework
the frequency invariance handling in the cpufreq core and drivers, add
new hardware support to a couple of cpufreq drivers, fix a number of
assorted issues and clean up the code all over.
Specifics:
- Rework cpufreq statistics collection to allow it to take place when
fast frequency switching is enabled in the governor (Viresh Kumar).
- Make the cpufreq core set the frequency scale on behalf of the
driver and update several cpufreq drivers accordingly (Ionela
Voinescu, Valentin Schneider).
- Add new hardware support to the STI and qcom cpufreq drivers and
improve them (Alain Volmat, Manivannan Sadhasivam).
- Fix multiple assorted issues in cpufreq drivers (Jon Hunter,
Krzysztof Kozlowski, Matthias Kaehlcke, Pali Rohár, Stephan
Gerhold, Viresh Kumar).
- Fix several assorted issues in the operating performance points
(OPP) framework (Stephan Gerhold, Viresh Kumar).
- Allow devfreq drivers to fetch devfreq instances by DT enumeration
instead of using explicit phandles and modify the devfreq core code
to support driver-specific devfreq DT bindings (Leonard Crestez,
Chanwoo Choi).
- Improve initial hardware resetting in the tegra30 devfreq driver
and clean up the tegra cpuidle driver (Dmitry Osipenko).
- Update the cpuidle core to collect state entry rejection statistics
and expose them via sysfs (Lina Iyer).
- Improve the ACPI _CST code handling diagnostics (Chen Yu).
- Update the PSCI cpuidle driver to allow the PM domain
initialization to occur in the OSI mode as well as in the PC mode
(Ulf Hansson).
- Rework the generic power domains (genpd) core code to allow domain
power off transition to be aborted in the absence of the "power
off" domain callback (Ulf Hansson).
- Fix two suspend-to-idle issues in the ACPI EC driver (Rafael
Wysocki).
- Fix the handling of timer_expires in the PM-runtime framework on
32-bit systems and the handling of device links in it (Grygorii
Strashko, Xiang Chen).
- Add IO requests batching support to the hibernate image saving and
reading code and drop a bogus get_gendisk() from there (Xiaoyi
Chen, Christoph Hellwig).
- Allow PCIe ports to be put into the D3cold power state if they are
power-manageable via ACPI (Lukas Wunner).
- Add missing header file include to a power capping driver (Pujin
Shi).
- Clean up the qcom-cpr AVS driver a bit (Liu Shixin).
- Kevin Hilman steps down as designated reviwer of adaptive voltage
scaling (AVS) drivers (Kevin Hilman)"
* tag 'pm-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (65 commits)
cpufreq: stats: Fix string format specifier mismatch
arm: disable frequency invariance for CONFIG_BL_SWITCHER
cpufreq,arm,arm64: restructure definitions of arch_set_freq_scale()
cpufreq: stats: Add memory barrier to store_reset()
cpufreq: schedutil: Simplify sugov_fast_switch()
ACPI: EC: PM: Drop ec_no_wakeup check from acpi_ec_dispatch_gpe()
ACPI: EC: PM: Flush EC work unconditionally after wakeup
PCI/ACPI: Whitelist hotplug ports for D3 if power managed by ACPI
PM: hibernate: remove the bogus call to get_gendisk() in software_resume()
cpufreq: Move traces and update to policy->cur to cpufreq core
cpufreq: stats: Enable stats for fast-switch as well
cpufreq: stats: Mark few conditionals with unlikely()
cpufreq: stats: Remove locking
cpufreq: stats: Defer stats update to cpufreq_stats_record_transition()
PM: domains: Allow to abort power off when no ->power_off() callback
PM: domains: Rename power state enums for genpd
PM / devfreq: tegra30: Improve initial hardware resetting
PM / devfreq: event: Change prototype of devfreq_event_get_edev_by_phandle function
PM / devfreq: Change prototype of devfreq_get_devfreq_by_phandle function
PM / devfreq: Add devfreq_get_devfreq_by_node function
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCX4aNVgAKCRCAXGG7T9hj
vlrDAQDQ2qelTKKMEV9atKr0RTkHAKrhUidzlTINjFx7BIrTfQEA7TmDr3j0weQU
521+bxE803OEWElp2Qta30boXgGGXQo=
=jKt7
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.10b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- two small cleanup patches
- avoid error messages when initializing MCA banks in a Xen dom0
- a small series for converting the Xen gntdev driver to use
pin_user_pages*() instead of get_user_pages*()
- intermediate fix for running as a Xen guest on Arm with KPTI enabled
(the final solution will need new Xen functionality)
* tag 'for-linus-5.10b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: Fix typo in xen_pagetable_p2m_free()
x86/xen: disable Firmware First mode for correctable memory errors
xen/arm: do not setup the runstate info page if kpti is enabled
xen: remove redundant initialization of variable ret
xen/gntdev.c: Convert get_user_pages*() to pin_user_pages*()
xen/gntdev.c: Mark pages as dirty
We account the PTE level of the page tables to the process in order to
make smarter OOM decisions and help diagnose why memory is fragmented.
For these same reasons, we should account pages allocated for PMDs. With
larger process address spaces and ASLR, the number of PMDs in use is
higher than it used to be so the inaccuracy is starting to matter.
[rppt@linux.ibm.com: arm: __pmd_free_tlb(): call page table destructor]
Link: https://lkml.kernel.org/r/20200825111303.GB69694@linux.ibm.com
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Anders Roxell <anders.roxell@linaro.org>
Link: http://lkml.kernel.org/r/20200627184642.GF25039@casper.infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull copy_and_csum cleanups from Al Viro:
"Saner calling conventions for csum_and_copy_..._user() and friends"
[ Removing 800+ lines of code and cleaning stuff up is good - Linus ]
* 'work.csum_and_copy' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ppc: propagate the calling conventions change down to csum_partial_copy_generic()
amd64: switch csum_partial_copy_generic() to new calling conventions
sparc64: propagate the calling convention changes down to __csum_partial_copy_...()
xtensa: propagate the calling conventions change down into csum_partial_copy_generic()
mips: propagate the calling convention change down into __csum_partial_copy_..._user()
mips: __csum_partial_copy_kernel() has no users left
mips: csum_and_copy_{to,from}_user() are never called under KERNEL_DS
sparc32: propagate the calling conventions change down to __csum_partial_copy_sparc_generic()
i386: propagate the calling conventions change down to csum_partial_copy_generic()
sh: propage the calling conventions change down to csum_partial_copy_generic()
m68k: get rid of zeroing destination on error in csum_and_copy_from_user()
arm: propagate the calling convention changes down to csum_partial_copy_from_user()
alpha: propagate the calling convention changes down to csum_partial_copy.c helpers
saner calling conventions for csum_and_copy_..._user()
csum_and_copy_..._user(): pass 0xffffffff instead of 0 as initial sum
csum_partial_copy_nocheck(): drop the last argument
unify generic instances of csum_partial_copy_nocheck()
icmp_push_reply(): reorder adding the checksum up
skb_copy_and_csum_bits(): don't bother with the last argument
because the heuristics that various linkers & compilers use to handle them
(include these bits into the output image vs discarding them silently)
are both highly idiosyncratic and also version dependent.
Instead of this historically problematic mess, this tree by Kees Cook (et al)
adds build time asserts and build time warnings if there's any orphan section
in the kernel or if a section is not sized as expected.
And because we relied on so many silent assumptions in this area, fix a metric
ton of dependencies and some outright bugs related to this, before we can
finally enable the checks on the x86, ARM and ARM64 platforms.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=fXAw
-----END PGP SIGNATURE-----
Merge tag 'core-build-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull orphan section checking from Ingo Molnar:
"Orphan link sections were a long-standing source of obscure bugs,
because the heuristics that various linkers & compilers use to handle
them (include these bits into the output image vs discarding them
silently) are both highly idiosyncratic and also version dependent.
Instead of this historically problematic mess, this tree by Kees Cook
(et al) adds build time asserts and build time warnings if there's any
orphan section in the kernel or if a section is not sized as expected.
And because we relied on so many silent assumptions in this area, fix
a metric ton of dependencies and some outright bugs related to this,
before we can finally enable the checks on the x86, ARM and ARM64
platforms"
* tag 'core-build-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/boot/compressed: Warn on orphan section placement
x86/build: Warn on orphan section placement
arm/boot: Warn on orphan section placement
arm/build: Warn on orphan section placement
arm64/build: Warn on orphan section placement
x86/boot/compressed: Add missing debugging sections to output
x86/boot/compressed: Remove, discard, or assert for unwanted sections
x86/boot/compressed: Reorganize zero-size section asserts
x86/build: Add asserts for unwanted sections
x86/build: Enforce an empty .got.plt section
x86/asm: Avoid generating unused kprobe sections
arm/boot: Handle all sections explicitly
arm/build: Assert for unwanted sections
arm/build: Add missing sections
arm/build: Explicitly keep .ARM.attributes sections
arm/build: Refactor linker script headers
arm64/build: Assert for unwanted sections
arm64/build: Add missing DWARF sections
arm64/build: Use common DISCARDS in linker script
arm64/build: Remove .eh_frame* sections due to unwind tables
...
- Preliminary RISC-V enablement - the bulk of it will arrive via the RISCV tree.
- Relax decompressed image placement rules for 32-bit ARM
- Add support for passing MOK certificate table contents via a config table
rather than a EFI variable.
- Add support for 18 bit DIMM row IDs in the CPER records.
- Work around broken Dell firmware that passes the entire Boot#### variable
contents as the command line
- Add definition of the EFI_MEMORY_CPU_CRYPTO memory attribute so we can
identify it in the memory map listings.
- Don't abort the boot on arm64 if the EFI RNG protocol is available but
returns with an error
- Replace slashes with exclamation marks in efivarfs file names
- Split efi-pstore from the deprecated efivars sysfs code, so we can
disable the latter on !x86.
- Misc fixes, cleanups and updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ZNI8
-----END PGP SIGNATURE-----
Merge tag 'efi-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI changes from Ingo Molnar:
- Preliminary RISC-V enablement - the bulk of it will arrive via the
RISCV tree.
- Relax decompressed image placement rules for 32-bit ARM
- Add support for passing MOK certificate table contents via a config
table rather than a EFI variable.
- Add support for 18 bit DIMM row IDs in the CPER records.
- Work around broken Dell firmware that passes the entire Boot####
variable contents as the command line
- Add definition of the EFI_MEMORY_CPU_CRYPTO memory attribute so we
can identify it in the memory map listings.
- Don't abort the boot on arm64 if the EFI RNG protocol is available
but returns with an error
- Replace slashes with exclamation marks in efivarfs file names
- Split efi-pstore from the deprecated efivars sysfs code, so we can
disable the latter on !x86.
- Misc fixes, cleanups and updates.
* tag 'efi-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
efi: mokvar: add missing include of asm/early_ioremap.h
efi: efivars: limit availability to X86 builds
efi: remove some false dependencies on CONFIG_EFI_VARS
efi: gsmi: fix false dependency on CONFIG_EFI_VARS
efi: efivars: un-export efivars_sysfs_init()
efi: pstore: move workqueue handling out of efivars
efi: pstore: disentangle from deprecated efivars module
efi: mokvar-table: fix some issues in new code
efi/arm64: libstub: Deal gracefully with EFI_RNG_PROTOCOL failure
efivarfs: Replace invalid slashes with exclamation marks in dentries.
efi: Delete deprecated parameter comments
efi/libstub: Fix missing-prototypes in string.c
efi: Add definition of EFI_MEMORY_CPU_CRYPTO and ability to report it
cper,edac,efi: Memory Error Record: bank group/address and chip id
edac,ghes,cper: Add Row Extension to Memory Error Record
efi/x86: Add a quirk to support command line arguments on Dell EFI firmware
efi/libstub: Add efi_warn and *_once logging helpers
integrity: Load certs from the EFI MOK config table
integrity: Move import of MokListRT certs to a separate routine
efi: Support for MOK variable config table
...
big.LITTLE switching complicates the setting of a correct cpufreq-based
frequency invariance scale factor due to (as observed in
drivers/cpufreq/vexpress-spc-cpufreq.c):
- Incorrect current and maximum frequencies as a result of the
exposure of a virtual frequency table to the cpufreq core,
- Missed updates as a result of asynchronous frequency adjustments
caused by frequency changes in other CPU pairs.
Given that its functionality is atypical in regards to frequency
invariance and this is an old technology, disable frequency
invariance for when big.LITTLE switching is configured in to prevent
incorrect scale setting.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Suggested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Compared to other arch_* functions, arch_set_freq_scale() has an atypical
weak definition that can be replaced by a strong architecture specific
implementation.
The more typical support for architectural functions involves defining
an empty stub in a header file if the symbol is not already defined in
architecture code. Some examples involve:
- #define arch_scale_freq_capacity topology_get_freq_scale
- #define arch_scale_freq_invariant topology_scale_freq_invariant
- #define arch_scale_cpu_capacity topology_get_cpu_scale
- #define arch_update_cpu_topology topology_update_cpu_topology
- #define arch_scale_thermal_pressure topology_get_thermal_pressure
- #define arch_set_thermal_pressure topology_set_thermal_pressure
Bring arch_set_freq_scale() in line with these functions by renaming it to
topology_set_freq_scale() in the arch topology driver, and by defining the
arch_set_freq_scale symbol to point to the new function for arm and arm64.
While there are other users of the arch_topology driver, this patch defines
arch_set_freq_scale for arm and arm64 only, due to their existing
definitions of arch_scale_freq_capacity. This is the getter function of the
frequency invariance scale factor and without a getter function, the
setter function - arch_set_freq_scale() has not purpose.
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com> (BL_SWITCHER and topology parts)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of dma-debug.h is not required by anything outside of kernel/dma.
Move the four declarations needed by dma-mappin.h or dma-ops providers
into dma-mapping.h and dma-map-ops.h, and move the remainder of the
file to kernel/dma/debug.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
The VCPUOP_register_runstate_memory_area hypercall takes a virtual
address of a buffer as a parameter. The semantics of the hypercall are
such that the virtual address should always be valid.
When KPTI is enabled and we are running userspace code, the virtual
address is not valid, thus, Linux is violating the semantics of
VCPUOP_register_runstate_memory_area.
Do not call VCPUOP_register_runstate_memory_area when KPTI is enabled.
Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com>
CC: Bertrand Marquis <Bertrand.Marquis@arm.com>
CC: boris.ostrovsky@oracle.com
CC: jgross@suse.com
Link: https://lore.kernel.org/r/20200924234955.15455-1-sstabellini@kernel.org
Reviewed-by: Bertrand Marquis <bertrand.marquis@arm.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Switch the omap1510 platform ohci device to use dma_direct_set_offset
to set the DMA offset instead of using direct hooks into the DMA
mapping code and remove the now unused hooks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
There was a request to preprocess the module linker script like we
do for the vmlinux one. (https://lkml.org/lkml/2020/8/21/512)
The difference between vmlinux.lds and module.lds is that the latter
is needed for external module builds, thus must be cleaned up by
'make mrproper' instead of 'make clean'. Also, it must be created
by 'make modules_prepare'.
You cannot put it in arch/$(SRCARCH)/kernel/, which is cleaned up by
'make clean'. I moved arch/$(SRCARCH)/kernel/module.lds to
arch/$(SRCARCH)/include/asm/module.lds.h, which is included from
scripts/module.lds.S.
scripts/module.lds is fine because 'make clean' keeps all the
build artifacts under scripts/.
You can add arch-specific sections in <asm/module.lds.h>.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
The msi_ctrl, io_optional and align_resource fields in struct hw_pci are
currently unused by arm/mach PCI host controller drivers and we won't
be adding any new users.
Remove them and related code.
Link: https://lore.kernel.org/r/20200904141607.4066-1-lorenzo.pieralisi@arm.com
Link: https://lore.kernel.org/r/20200916103045.28651-1-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
arch_scale_freq_invariant() is used by schedutil to determine whether
the scheduler's load-tracking signals are frequency invariant. Its
definition is overridable, though by default it is hardcoded to 'true'
if arch_scale_freq_capacity() is defined ('false' otherwise).
This behaviour is not overridden on arm, arm64 and other users of the
generic arch topology driver, which is somewhat precarious:
arch_scale_freq_capacity() will always be defined, yet not all cpufreq
drivers are guaranteed to drive the frequency invariance scale factor
setting. In other words, the load-tracking signals may very well *not*
be frequency invariant.
Now that cpufreq can be queried on whether the current driver is driving
the Frequency Invariance (FI) scale setting, the current situation can
be improved. This combines the query of whether cpufreq supports the
setting of the frequency scale factor, with whether all online CPUs are
counter-based FI enabled.
While cpufreq FI enablement applies at system level, for all CPUs,
counter-based FI support could also be used for only a subset of CPUs to
set the invariance scale factor. Therefore, if cpufreq-based FI support
is present, we consider the system to be invariant. If missing, we
require all online CPUs to be counter-based FI enabled in order for the
full system to be considered invariant.
If the system ends up not being invariant, a new condition is needed in
the counter initialization code that disables all scale factor setting
based on counters.
Precedence of counters over cpufreq use is not important here. The
invariant status is only given to the system if all CPUs have at least
one method of setting the frequency scale factor.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Ionela Voinescu <ionela.voinescu@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The new field 'dma_range_map' in struct device is used to facilitate the
use of single or multiple offsets between mapping regions of cpu addrs and
dma addrs. It subsumes the role of "dev->dma_pfn_offset" which was only
capable of holding a single uniform offset and had no region bounds
checking.
The function of_dma_get_range() has been modified so that it takes a single
argument -- the device node -- and returns a map, NULL, or an error code.
The map is an array that holds the information regarding the DMA regions.
Each range entry contains the address offset, the cpu_start address, the
dma_start address, and the size of the region.
of_dma_configure() is the typical manner to set range offsets but there are
a number of ad hoc assignments to "dev->dma_pfn_offset" in the kernel
driver code. These cases now invoke the function
dma_direct_set_offset(dev, cpu_addr, dma_addr, size).
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
[hch: various interface cleanups]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Move the helpers to translate to and from direct mapping DMA addresses
to dma-direct.h. This not only is the most logical place, but the new
placement also avoids dependency loops with pending commits.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Let's switch the arm code to the core accounting, which already
does everything we need.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The old IPI registration interface is now unused on arm, so let's
get rid of it.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The way we use the base of DRAM in the EFI stub is problematic as it
is ill defined what the base of DRAM actually means. There are some
restrictions on the placement of FDT and initrd which are defined in
terms of dram_base, but given that the placement of the kernel in
memory is what defines these boundaries (as on ARM, this is where the
linear region starts), it is better to use the image address in these
cases, and disregard dram_base altogether.
Reviewed-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Tested-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Instead of a flow control selection mechanism specifically for
8250, make this available for all debug UARTs. If the debug
UART supports waiting for CTS to be asserted, then this code
can be activated for terminals that need it.
We keep the defaults for EBSA110, Footbridge, Gemini and RPC
so that this still works as expected for these older platforms:
they assume that flow control shall be enabled for debug
prints.
I switch the location of the check for
ifdef CONFIG_DEBUG_UART_FLOW_CONTROL from the actual debug
UART drivers: the code would get compiled-out for 8250 and
Tegra unless their custom config (or passing -DFLOW_CONTROL
in the Tegra case) was not set. Instead this is conditional
at the three places where we print debug messages. The idea
is that debug UARTs can be implemented without this ifdef
boilerplate so they look cleaner, alas the ifdef has to be
somewhere.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch was triggered by a remark from Russell that
introducing a call to the waituart (needed to fix debug prints
on the Qualcomm platforms) was dangerous because in some cases
this will involve waiting for a modem CTS (clear to send)
signal, and debug messages would maybe not work on platforms
with no modem connected to the UART port: they will just
hang waiting for the modem to assert CTS and this might never
happen.
Looking through all UART debug drivers implementing the waituart
macro I discovered that all users except two actually use this
macro to check if the UART is ready for TX, let's call this
TXRDY.
Only two debug UART drivers actually check for CTS:
- arch/arm/include/debug/8250.S
- arch/arm/include/debug/tegra.S
The former is very significant since the 8250 is possibly
the most common UART on the planet.
We have the following problem: the semantics of waituart are
ambiguous making it dangerous to introduce the macro to debug
code fixing debug prints for Qualcomm. To start to pry this
problem apart, this patch does the following:
- Convert all debug UART drivers to define two macros:
- waituartcts with the clear semantic to wait for CTS
to be asserted
- waituarttxrdy with the clear semantic to wait for the TX
capability of the UART to be ready
- When doing this take care to assign the right function to
each drivers macro, so they now do exactly the above.
- Update the three sites in the kernel invoking the waituart
macro to call waituartcts/waituarttxrdy in sequence, so that
the functional impact on the kernel should be zero.
After this we can start to change the code sites using this
code to do the right thing.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
In order to deal with IPIs as normal interrupts, let's add
a new way to register them with the architecture code.
set_smp_ipi_range() takes a range of interrupts, and allows
the arch code to request them as if the were normal interrupts.
A standard handler is then called by the core IRQ code to deal
with the IPI.
This means that we don't need to call irq_enter/irq_exit, and
that we don't need to deal with set_irq_regs either. So let's
move the dispatcher into its own function, and leave handle_IPI()
as a compatibility function.
On the sending side, let's make use of ipi_send_mask, which
already exists for this purpose.
One of the major difference is that we end up, in some cases
(such as when performing IRQ time accounting on the scheduler
IPI), end up with nested irq_enter()/irq_exit() pairs.
Other than the (relatively small) overhead, there should be
no consequences to it (these pairs are designed to nest
correctly, and the accounting shouldn't be off).
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
The __phys_to_dma vs phys_to_dma distinction isn't exactly obvious. Try
to improve the situation by renaming __phys_to_dma to
phys_to_dma_unencryped, and not forcing architectures that want to
override phys_to_dma to actually provide __phys_to_dma.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
There is no harm in just always clearing the SME encryption bit, while
significantly simplifying the interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
72165 has the same memory map as 7278 and the same physical address for
the UART, alias the definition accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In preparation for warning on orphan sections, enforce
expected-to-be-zero-sized sections (since discarding them might hide
problems with them suddenly gaining unexpected entries).
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20200821194310.3089815-19-keescook@chromium.org
Add missing text stub sections .vfp11_veneer and .v4_bx, as well as
missing DWARF sections, when present in the build.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20200821194310.3089815-18-keescook@chromium.org
In preparation for adding --orphan-handling=warn, refactor the linker
script header includes, and extract common macros.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20200821194310.3089815-16-keescook@chromium.org
... and get rid of the "clean the destination on error" crap.
Simplifies the fault handlers and the function itself...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All callers of these primitives will
* discard anything we might've copied in case of error
* ignore the csum value in case of error
* always pass 0xffffffff as the initial sum, so the
resulting csum value (in case of success, that is) will never be 0.
That suggest the following calling conventions:
* don't pass err_ptr - just return 0 on error.
* don't bother with zeroing destination, etc. in case of error
* don't pass the initial sum - just use 0xffffffff.
This commit does the minimal conversion in the instances of csum_and_copy_...();
the changes of actual asm code behind them are done later in the series.
Note that this asm code is often shared with csum_partial_copy_nocheck();
the difference is that csum_partial_copy_nocheck() passes 0 for initial
sum while csum_and_copy_..._user() pass 0xffffffff. Fortunately, we are
free to pass 0xffffffff in all cases and subsequent patches will use that
freedom without any special comments.
A part that could be split off: parisc and uml/i386 claimed to have
csum_and_copy_to_user() instances of their own, but those were identical
to the generic one, so we simply drop them. Not sure if it's worth
a separate commit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It's always 0. Note that we theoretically could use ~0U as well -
result will be the same modulo 0xffff, _if_ the damn thing did the
right thing for any value of initial sum; later we'll make use of
that when convenient.
However, unlike csum_and_copy_..._user(), there are instances that
did not work for arbitrary initial sums; c6x is one such.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
quite a few architectures have the same csum_partial_copy_nocheck() -
simply memcpy() the data and then return the csum of the copy.
hexagon, parisc, ia64, s390, um: explicitly spelled out that way.
arc, arm64, csky, h8300, m68k/nommu, microblaze, mips/GENERIC_CSUM, nds32,
nios2, openrisc, riscv, unicore32: end up picking the same thing spelled
out in lib/checksum.h (with varying amounts of perversions along the way).
everybody else (alpha, arm, c6x, m68k/mmu, mips/!GENERIC_CSUM, powerpc,
sh, sparc, x86, xtensa) have non-generic variants. For all except c6x
the declaration is in their asm/checksum.h. c6x uses the wrapper
from asm-generic/checksum.h that would normally lead to the lib/checksum.h
instance, but in case of c6x we end up using an asm function from arch/c6x
instead.
Screw that mess - have architectures with private instances define
_HAVE_ARCH_CSUM_AND_COPY in their asm/checksum.h and have the default
one right in net/checksum.h conditional on _HAVE_ARCH_CSUM_AND_COPY
*not* defined.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
72164 has the same memory map as 7278 and the same physical address for
the UART, alias the definition accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- Preparatory work to allow S390 to switch over to the generic VDSO
implementation.
S390 requires that the VDSO data pointer is handed in to the counter
read function when time namespace support is enabled. Adding the pointer
is a NOOP for all other architectures because the compiler is supposed
to optimize that out when it is unused in the architecture specific
inline. The change also solved a similar problem for MIPS which
fortunately has time namespaces not yet enabled.
S390 needs to update clock related VDSO data independent of the
timekeeping updates. This was solved so far with yet another sequence
counter in the S390 implementation. A better solution is to utilize the
already existing VDSO sequence count for this. The core code now exposes
helper functions which allow to serialize against the timekeeper code
and against concurrent readers.
S390 needs extra data for their clock readout function. The initial
common VDSO data structure did not provide a way to add that. It now has
an embedded architecture specific struct embedded which defaults to an
empty struct.
Doing this now avoids tree dependencies and conflicts post rc1 and
allows all other architectures which work on generic VDSO support to
work from a common upstream base.
- A trivial comment fix.
-----BEGIN PGP SIGNATURE-----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=y8Z5
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timekeeping updates from Thomas Gleixner:
"A set of timekeeping/VDSO updates:
- Preparatory work to allow S390 to switch over to the generic VDSO
implementation.
S390 requires that the VDSO data pointer is handed in to the
counter read function when time namespace support is enabled.
Adding the pointer is a NOOP for all other architectures because
the compiler is supposed to optimize that out when it is unused in
the architecture specific inline. The change also solved a similar
problem for MIPS which fortunately has time namespaces not yet
enabled.
S390 needs to update clock related VDSO data independent of the
timekeeping updates. This was solved so far with yet another
sequence counter in the S390 implementation. A better solution is
to utilize the already existing VDSO sequence count for this. The
core code now exposes helper functions which allow to serialize
against the timekeeper code and against concurrent readers.
S390 needs extra data for their clock readout function. The initial
common VDSO data structure did not provide a way to add that. It
now has an embedded architecture specific struct embedded which
defaults to an empty struct.
Doing this now avoids tree dependencies and conflicts post rc1 and
allows all other architectures which work on generic VDSO support
to work from a common upstream base.
- A trivial comment fix"
* tag 'timers-urgent-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Delete repeated words in comments
lib/vdso: Allow to add architecture-specific vdso data
timekeeping/vsyscall: Provide vdso_update_begin/end()
vdso/treewide: Add vdso_data pointer argument to __arch_get_hw_counter()
Merge more updates from Andrew Morton:
- most of the rest of MM (memcg, hugetlb, vmscan, proc, compaction,
mempolicy, oom-kill, hugetlbfs, migration, thp, cma, util,
memory-hotplug, cleanups, uaccess, migration, gup, pagemap),
- various other subsystems (alpha, misc, sparse, bitmap, lib, bitops,
checkpatch, autofs, minix, nilfs, ufs, fat, signals, kmod, coredump,
exec, kdump, rapidio, panic, kcov, kgdb, ipc).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
mm/gup: remove task_struct pointer for all gup code
mm: clean up the last pieces of page fault accountings
mm/xtensa: use general page fault accounting
mm/x86: use general page fault accounting
mm/sparc64: use general page fault accounting
mm/sparc32: use general page fault accounting
mm/sh: use general page fault accounting
mm/s390: use general page fault accounting
mm/riscv: use general page fault accounting
mm/powerpc: use general page fault accounting
mm/parisc: use general page fault accounting
mm/openrisc: use general page fault accounting
mm/nios2: use general page fault accounting
mm/nds32: use general page fault accounting
mm/mips: use general page fault accounting
mm/microblaze: use general page fault accounting
mm/m68k: use general page fault accounting
mm/ia64: use general page fault accounting
mm/hexagon: use general page fault accounting
mm/csky: use general page fault accounting
...
segment_eq is only used to implement uaccess_kernel. Just open code
uaccess_kernel in the arch uaccess headers and remove one layer of
indirection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Greentime Hu <green.hu@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Link: http://lkml.kernel.org/r/20200710135706.537715-5-hch@lst.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Including:
- Removal of the dev->archdata.iommu (or similar) pointers from
most architectures. Only Sparc is left, but this is private to
Sparc as their drivers don't use the IOMMU-API.
- ARM-SMMU Updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell
Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d Updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel
drivers into their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test
coverage)
-----BEGIN PGP SIGNATURE-----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=3O2Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Remove of the dev->archdata.iommu (or similar) pointers from most
architectures. Only Sparc is left, but this is private to Sparc as
their drivers don't use the IOMMU-API.
- ARM-SMMU updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel drivers into
their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test coverage)
* tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (77 commits)
iommu/amd: Move Kconfig and Makefile bits down into amd directory
iommu/vt-d: Move Kconfig and Makefile bits down into intel directory
iommu/arm-smmu: Move Arm SMMU drivers into their own subdirectory
iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu
iommu: Add gfp parameter to io_pgtable_ops->map()
iommu: Mark __iommu_map_sg() as static
iommu/vt-d: Rename intel-pasid.h to pasid.h
iommu/vt-d: Add page response ops support
iommu/vt-d: Report page request faults for guest SVA
iommu/vt-d: Add a helper to get svm and sdev for pasid
iommu/vt-d: Refactor device_to_iommu() helper
iommu/vt-d: Disable multiple GPASID-dev bind
iommu/vt-d: Warn on out-of-range invalidation address
iommu/vt-d: Fix devTLB flush for vSVA
iommu/vt-d: Handle non-page aligned address
iommu/vt-d: Fix PASID devTLB invalidation
iommu/vt-d: Remove global page support in devTLB flush
iommu/vt-d: Enforce PASID devTLB field mask
iommu: Make some functions static
iommu/amd: Remove double zero check
...
Most architectures define pgd_free() as a wrapper for free_page().
Provide a generic version in asm-generic/pgalloc.h and enable its use for
most architectures.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Matthew Wilcox <willy@infradead.org>
Link: http://lkml.kernel.org/r/20200627143453.31835-7-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For most architectures that support >2 levels of page tables,
pmd_alloc_one() is a wrapper for __get_free_pages(), sometimes with
__GFP_ZERO and sometimes followed by memset(0) instead.
More elaborate versions on arm64 and x86 account memory for the user page
tables and call to pgtable_pmd_page_ctor() as the part of PMD page
initialization.
Move the arm64 version to include/asm-generic/pgalloc.h and use the
generic version on several architectures.
The pgtable_pmd_page_ctor() is a NOP when ARCH_ENABLE_SPLIT_PMD_PTLOCK is
not enabled, so there is no functional change for most architectures
except of the addition of __GFP_ACCOUNT for allocation of user page
tables.
The pmd_free() is a wrapper for free_page() in all the cases, so no
functional change here.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/20200627143453.31835-5-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "mm: cleanup usage of <asm/pgalloc.h>"
Most architectures have very similar versions of pXd_alloc_one() and
pXd_free_one() for intermediate levels of page table. These patches add
generic versions of these functions in <asm-generic/pgalloc.h> and enable
use of the generic functions where appropriate.
In addition, functions declared and defined in <asm/pgalloc.h> headers are
used mostly by core mm and early mm initialization in arch and there is no
actual reason to have the <asm/pgalloc.h> included all over the place.
The first patch in this series removes unneeded includes of
<asm/pgalloc.h>
In the end it didn't work out as neatly as I hoped and moving
pXd_alloc_track() definitions to <asm-generic/pgalloc.h> would require
unnecessary changes to arches that have custom page table allocations, so
I've decided to move lib/ioremap.c to mm/ and make pgalloc-track.h local
to mm/.
This patch (of 8):
In most cases <asm/pgalloc.h> header is required only for allocations of
page table memory. Most of the .c files that include that header do not
use symbols declared in <asm/pgalloc.h> and do not require that header.
As for the other header files that used to include <asm/pgalloc.h>, it is
possible to move that include into the .c file that actually uses symbols
from <asm/pgalloc.h> and drop the include from the header file.
The process was somewhat automated using
sed -i -E '/[<"]asm\/pgalloc\.h/d' \
$(grep -L -w -f /tmp/xx \
$(git grep -E -l '[<"]asm/pgalloc\.h'))
where /tmp/xx contains all the symbols defined in
arch/*/include/asm/pgalloc.h.
[rppt@linux.ibm.com: fix powerpc warning]
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Matthew Wilcox <willy@infradead.org>
Link: http://lkml.kernel.org/r/20200627143453.31835-1-rppt@kernel.org
Link: http://lkml.kernel.org/r/20200627143453.31835-2-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- add arch/arm/Kbuild from Masahiro Yamada.
- simplify act_mm macro, since it contains an open-coded
get_thread_info.
- VFP updates for Clang from Stefan Agner.
- Fix unwinder for Clang from Nathan Huckleberry.
- Remove unused it8152 PCI host controller, used by the removed cm-x2xx
platforms from Mike Rapoport.
- Further explanation of __range_ok().
- Remove kimage_voffset that isn't used anymore from Marc Zyngier.
- Drop ancient Thumb-2 workaround for old binutils from Ard Biesheuvel.
- Documentation cleanup for mach-* from Pete Zaitcev.
-----BEGIN PGP SIGNATURE-----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=RWzO
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- add arch/arm/Kbuild from Masahiro Yamada.
- simplify act_mm macro, since it contains an open-coded
get_thread_info.
- VFP updates for Clang from Stefan Agner.
- Fix unwinder for Clang from Nathan Huckleberry.
- Remove unused it8152 PCI host controller, used by the removed cm-x2xx
platforms from Mike Rapoport.
- Further explanation of __range_ok().
- Remove kimage_voffset that isn't used anymore from Marc Zyngier.
- Drop ancient Thumb-2 workaround for old binutils from Ard Biesheuvel.
- Documentation cleanup for mach-* from Pete Zaitcev.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8996/1: Documentation/Clean up the description of mach-<class>
ARM: 8995/1: drop Thumb-2 workaround for ancient binutils
ARM: 8994/1: mm: drop kimage_voffset which was only used by KVM
ARM: uaccess: add further explanation of __range_ok()
ARM: 8993/1: remove it8152 PCI controller driver
ARM: 8992/1: Fix unwind_frame for clang-built kernels
ARM: 8991/1: use VFP assembler mnemonics if available
ARM: 8990/1: use VFP assembler mnemonics in register load/store macros
ARM: 8989/1: use .fpu assembler directives instead of assembler arguments
ARM: 8982/1: mm: Simplify act_mm macro
ARM: 8981/1: add arch/arm/Kbuild
MIPS already uses and S390 will need the vdso data pointer in
__arch_get_hw_counter().
This works nicely as long as the architecture does not support time
namespaces in the VDSO. With time namespaces enabled the regular
accessor to the vdso data pointer __arch_get_vdso_data() will return the
namespace specific VDSO data page for tasks which are part of a
non-root time namespace. This would cause the architectures which need
the vdso data pointer in __arch_get_hw_counter() to access the wrong
vdso data page.
Add a vdso_data pointer argument to __arch_get_hw_counter() and hand it in
from the call sites in the core code. For architectures which do not need
the data pointer in their counter accessor function the compiler will just
optimize it out.
Fix up all existing architecture implementations and make MIPS utilize the
pointer instead of invoking the accessor function.
No functional change and no change in the resulting object code (except
MIPS).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/draft-87wo2ekuzn.fsf@nanos.tec.linutronix.de
- Improve uclamp performance by using a static key for the fast path
- Add the "sched_util_clamp_min_rt_default" sysctl, to optimize for
better power efficiency of RT tasks on battery powered devices.
(The default is to maximize performance & reduce RT latencies.)
- Improve utime and stime tracking accuracy, which had a fixed boundary
of error, which created larger and larger relative errors as the values
become larger. This is now replaced with more precise arithmetics,
using the new mul_u64_u64_div_u64() helper in math64.h.
- Improve the deadline scheduler, such as making it capacity aware
- Improve frequency-invariant scheduling
- Misc cleanups in energy/power aware scheduling
- Add sched_update_nr_running tracepoint to track changes to nr_running
- Documentation additions and updates
- Misc cleanups and smaller fixes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=PbO7
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Improve uclamp performance by using a static key for the fast path
- Add the "sched_util_clamp_min_rt_default" sysctl, to optimize for
better power efficiency of RT tasks on battery powered devices.
(The default is to maximize performance & reduce RT latencies.)
- Improve utime and stime tracking accuracy, which had a fixed boundary
of error, which created larger and larger relative errors as the
values become larger. This is now replaced with more precise
arithmetics, using the new mul_u64_u64_div_u64() helper in math64.h.
- Improve the deadline scheduler, such as making it capacity aware
- Improve frequency-invariant scheduling
- Misc cleanups in energy/power aware scheduling
- Add sched_update_nr_running tracepoint to track changes to nr_running
- Documentation additions and updates
- Misc cleanups and smaller fixes
* tag 'sched-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched/doc: Factorize bits between sched-energy.rst & sched-capacity.rst
sched/doc: Document capacity aware scheduling
sched: Document arch_scale_*_capacity()
arm, arm64: Fix selection of CONFIG_SCHED_THERMAL_PRESSURE
Documentation/sysctl: Document uclamp sysctl knobs
sched/uclamp: Add a new sysctl to control RT default boost value
sched/uclamp: Fix a deadlock when enabling uclamp static key
sched: Remove duplicated tick_nohz_full_enabled() check
sched: Fix a typo in a comment
sched/uclamp: Remove unnecessary mutex_init()
arm, arm64: Select CONFIG_SCHED_THERMAL_PRESSURE
sched: Cleanup SCHED_THERMAL_PRESSURE kconfig entry
arch_topology, sched/core: Cleanup thermal pressure definition
trace/events/sched.h: fix duplicated word
linux/sched/mm.h: drop duplicated words in comments
smp: Fix a potential usage of stale nr_cpus
sched/fair: update_pick_idlest() Select group with lowest group_util when idle_cpus are equal
sched: nohz: stop passing around unused "ticks" parameter.
sched: Better document ttwu()
sched: Add a tracepoint to track rq->nr_running
...
- LKMM updates: mostly documentation changes, but also some new litmus tests for atomic ops.
- KCSAN updates: the most important change is that GCC 11 now has all fixes in place
to support KCSAN, so GCC support can be enabled again. Also more annotations.
- futex updates: minor cleanups and simplifications
- seqlock updates: merge preparatory changes/cleanups for the 'associated locks' facilities.
- lockdep updates:
- simplify IRQ trace event handling
- add various new debug checks
- simplify header dependencies, split out <linux/lockdep_types.h>, decouple
lockdep from other low level headers some more
- fix NMI handling
- misc cleanups and smaller fixes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=3MTT
-----END PGP SIGNATURE-----
Merge tag 'locking-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
- LKMM updates: mostly documentation changes, but also some new litmus
tests for atomic ops.
- KCSAN updates: the most important change is that GCC 11 now has all
fixes in place to support KCSAN, so GCC support can be enabled again.
Also more annotations.
- futex updates: minor cleanups and simplifications
- seqlock updates: merge preparatory changes/cleanups for the
'associated locks' facilities.
- lockdep updates:
- simplify IRQ trace event handling
- add various new debug checks
- simplify header dependencies, split out <linux/lockdep_types.h>,
decouple lockdep from other low level headers some more
- fix NMI handling
- misc cleanups and smaller fixes
* tag 'locking-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
kcsan: Improve IRQ state trace reporting
lockdep: Refactor IRQ trace events fields into struct
seqlock: lockdep assert non-preemptibility on seqcount_t write
lockdep: Add preemption enabled/disabled assertion APIs
seqlock: Implement raw_seqcount_begin() in terms of raw_read_seqcount()
seqlock: Add kernel-doc for seqcount_t and seqlock_t APIs
seqlock: Reorder seqcount_t and seqlock_t API definitions
seqlock: seqcount_t latch: End read sections with read_seqcount_retry()
seqlock: Properly format kernel-doc code samples
Documentation: locking: Describe seqlock design and usage
locking/qspinlock: Do not include atomic.h from qspinlock_types.h
locking/atomic: Move ATOMIC_INIT into linux/types.h
lockdep: Move list.h inclusion into lockdep.h
locking/lockdep: Fix TRACE_IRQFLAGS vs. NMIs
futex: Remove unused or redundant includes
futex: Consistently use fshared as boolean
futex: Remove needless goto's
futex: Remove put_futex_key()
rwsem: fix commas in initialisation
docs: locking: Replace HTTP links with HTTPS ones
...
- Removal of the tremendously unpopular read_barrier_depends() barrier,
which is a NOP on all architectures apart from Alpha, in favour of
allowing architectures to override READ_ONCE() and do whatever dance
they need to do to ensure address dependencies provide LOAD ->
LOAD/STORE ordering. This work also offers a potential solution if
compilers are shown to convert LOAD -> LOAD address dependencies into
control dependencies (e.g. under LTO), as weakly ordered architectures
will effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic, augment
the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the device
ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions and
kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words.
-----BEGIN PGP SIGNATURE-----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=mh79
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 and cross-arch updates from Catalin Marinas:
"Here's a slightly wider-spread set of updates for 5.9.
Going outside the usual arch/arm64/ area is the removal of
read_barrier_depends() series from Will and the MSI/IOMMU ID
translation series from Lorenzo.
The notable arm64 updates include ARMv8.4 TLBI range operations and
translation level hint, time namespace support, and perf.
Summary:
- Removal of the tremendously unpopular read_barrier_depends()
barrier, which is a NOP on all architectures apart from Alpha, in
favour of allowing architectures to override READ_ONCE() and do
whatever dance they need to do to ensure address dependencies
provide LOAD -> LOAD/STORE ordering.
This work also offers a potential solution if compilers are shown
to convert LOAD -> LOAD address dependencies into control
dependencies (e.g. under LTO), as weakly ordered architectures will
effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at
LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic,
augment the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the
device ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions
and kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words"
Link: http://lkml.kernel.org/r/20200710165203.31284-1-will@kernel.org
Link: http://lkml.kernel.org/r/20200619082013.13661-1-lorenzo.pieralisi@arm.com
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (82 commits)
arm64: use IRQ_STACK_SIZE instead of THREAD_SIZE for irq stack
arm64/mm: save memory access in check_and_switch_context() fast switch path
arm64: sigcontext.h: delete duplicated word
arm64: ptrace.h: delete duplicated word
arm64: pgtable-hwdef.h: delete duplicated words
bus: fsl-mc: Add ACPI support for fsl-mc
bus/fsl-mc: Refactor the MSI domain creation in the DPRC driver
of/irq: Make of_msi_map_rid() PCI bus agnostic
of/irq: make of_msi_map_get_device_domain() bus agnostic
dt-bindings: arm: fsl: Add msi-map device-tree binding for fsl-mc bus
of/device: Add input id to of_dma_configure()
of/iommu: Make of_map_rid() PCI agnostic
ACPI/IORT: Add an input ID to acpi_dma_configure()
ACPI/IORT: Remove useless PCI bus walk
ACPI/IORT: Make iort_msi_map_rid() PCI agnostic
ACPI/IORT: Make iort_get_device_domain IRQ domain agnostic
ACPI/IORT: Make iort_match_node_callback walk the ACPI namespace for NC
arm64: enable time namespace support
arm64/vdso: Restrict splitting VVAR VMA
arm64/vdso: Handle faults on timens page
...
Fix build error for the case:
defined(CONFIG_SMP) && !defined(CONFIG_CPU_V6)
config: keystone_defconfig
CC arch/arm/kernel/signal.o
In file included from ../include/linux/random.h:14,
from ../arch/arm/kernel/signal.c:8:
../arch/arm/include/asm/percpu.h: In function ‘__my_cpu_offset’:
../arch/arm/include/asm/percpu.h:29:34: error: ‘current_stack_pointer’ undeclared (first use in this function); did you mean ‘user_stack_pointer’?
: "Q" (*(const unsigned long *)current_stack_pointer));
^~~~~~~~~~~~~~~~~~~~~
user_stack_pointer
Fixes: f227e3ec3b ("random32: update the net random state on interrupt and activity")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves ATOMIC_INIT from asm/atomic.h into linux/types.h.
This allows users of atomic_t to use ATOMIC_INIT without having to
include atomic.h as that way may lead to header loops.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Waiman Long <longman@redhat.com>
Link: https://lkml.kernel.org/r/20200729123105.GB7047@gondor.apana.org.au
Detail the success return condition, and that we rely on KERNEL_DS
being zero for this to operate correctly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The following commit:
14533a16c4 ("thermal/cpu-cooling, sched/core: Move the arch_set_thermal_pressure() API to generic scheduler code")
moved the definition of arch_set_thermal_pressure() to sched/core.c, but
kept its declaration in linux/arch_topology.h. When building e.g. an x86
kernel with CONFIG_SCHED_THERMAL_PRESSURE=y, cpufreq_cooling.c ends up
getting the declaration of arch_set_thermal_pressure() from
include/linux/arch_topology.h, which is somewhat awkward.
On top of this, sched/core.c unconditionally defines
o The thermal_pressure percpu variable
o arch_set_thermal_pressure()
while arch_scale_thermal_pressure() does nothing unless redefined by the
architecture.
arch_*() functions are meant to be defined by architectures, so revert the
aforementioned commit and re-implement it in a way that keeps
arch_set_thermal_pressure() architecture-definable, and doesn't define the
thermal pressure percpu variable for kernels that don't need
it (CONFIG_SCHED_THERMAL_PRESSURE=n).
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200712165917.9168-2-valentin.schneider@arm.com
The it8152 PCI host controller was only used by cm-x2xx platforms.
Since these platforms were removed, there is no point to keep it8152
driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The integrated assembler of Clang 10 and earlier do not allow to access
the VFP registers through the coprocessor load/store instructions:
arch/arm/vfp/vfpmodule.c:342:2: error: invalid operand for instruction
fmxr(FPEXC, fpexc & ~(FPEXC_EX|FPEXC_DEX|FPEXC_FP2V|FPEXC_VV|FPEXC_TRAP_MASK));
^
arch/arm/vfp/vfpinstr.h:79:6: note: expanded from macro 'fmxr'
asm("mcr p10, 7, %0, " vfpreg(_vfp_) ", cr0, 0 @ fmxr " #_vfp_ ", %0"
^
<inline asm>:1:6: note: instantiated into assembly here
mcr p10, 7, r0, cr8, cr0, 0 @ fmxr FPEXC, r0
^
This has been addressed with Clang 11 [0]. However, to support earlier
versions of Clang and for better readability use of VFP assembler
mnemonics still is preferred.
Ideally we would replace this code with the unified assembler language
mnemonics vmrs/vmsr on call sites along with .fpu assembler directives.
The GNU assembler supports the .fpu directive at least since 2.17 (when
documentation has been added). Since Linux requires binutils 2.21 it is
safe to use .fpu directive. However, binutils does not allow to use
FPINST or FPINST2 as an argument to vmrs/vmsr instructions up to
binutils 2.24 (see binutils commit 16d02dc907c5):
arch/arm/vfp/vfphw.S: Assembler messages:
arch/arm/vfp/vfphw.S:162: Error: operand 0 must be FPSID or FPSCR pr FPEXC -- `vmsr FPINST,r6'
arch/arm/vfp/vfphw.S:165: Error: operand 0 must be FPSID or FPSCR pr FPEXC -- `vmsr FPINST2,r8'
arch/arm/vfp/vfphw.S:235: Error: operand 1 must be a VFP extension System Register -- `vmrs r3,FPINST'
arch/arm/vfp/vfphw.S:238: Error: operand 1 must be a VFP extension System Register -- `vmrs r12,FPINST2'
Use as-instr in Kconfig to check if FPINST/FPINST2 can be used. If they
can be used make use of .fpu directives and UAL VFP mnemonics for
register access.
This allows to build vfpmodule.c with Clang and its integrated assembler.
[0] https://reviews.llvm.org/D59733
Link: https://github.com/ClangBuiltLinux/linux/issues/905
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The integrated assembler of Clang 10 and earlier do not allow to access
the VFP registers through the coprocessor load/store instructions:
<instantiation>:4:6: error: invalid operand for instruction
LDC p11, cr0, [r10],#32*4 @ FLDMIAD r10!, {d0-d15}
^
This has been addressed with Clang 11 [0]. However, to support earlier
versions of Clang and for better readability use of VFP assembler
mnemonics still is preferred.
Replace the coprocessor load/store instructions with explicit assembler
mnemonics to accessing the floating point coprocessor registers. Use
assembler directives to select the appropriate FPU version.
This allows to build these macros with GNU assembler as well as with
Clang's built-in assembler.
[0] https://reviews.llvm.org/D59733
Link: https://github.com/ClangBuiltLinux/linux/issues/905
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Now that 'smp_read_barrier_depends()' has gone the way of the Norwegian
Blue, drop the inclusion of <asm/barrier.h> in 'asm-generic/rwonce.h'.
This requires fixups to some architecture vdso headers which were
previously relying on 'asm/barrier.h' coming in via 'linux/compiler.h'.
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Will Deacon <will@kernel.org>
In order to use <asm/percpu.h> in irqflags.h, we need to make sure
asm/percpu.h does not itself depend on irqflags.h.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lkml.kernel.org/r/20200623083721.454517573@infradead.org
There are no users left, all drivers have been converted to use the
per-device private pointer offered by IOMMU core.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200625130836.1916-12-joro@8bytes.org
On 32-bit ARM, we may boot at HYP mode, or with the MMU and caches off
(or both), even though the EFI spec does not actually support this.
While booting at HYP mode is something we might tolerate, fiddling
with the caches is a more serious issue, as disabling the caches is
tricky to do safely from C code, and running without the Dcache makes
it impossible to support unaligned memory accesses, which is another
explicit requirement imposed by the EFI spec.
So take note of the CPU mode and MMU state in the EFI stub diagnostic
output so that we can easily diagnose any issues that may arise from
this. E.g.,
EFI stub: Entering in SVC mode with MMU enabled
Also, capture the CPSR and SCTLR system register values at EFI stub
entry, and after ExitBootServices() returns, and check whether the
MMU and Dcache were disabled at any point. If this is the case, a
diagnostic message like the following will be emitted:
efi: [Firmware Bug]: EFI stub was entered with MMU and Dcache disabled, please fix your firmware!
efi: CPSR at EFI stub entry : 0x600001d3
efi: SCTLR at EFI stub entry : 0x00c51838
efi: CPSR after ExitBootServices() : 0x600001d3
efi: SCTLR after ExitBootServices(): 0x00c50838
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Leif Lindholm <leif@nuviainc.com>
All architectures define pte_index() as
(address >> PAGE_SHIFT) & (PTRS_PER_PTE - 1)
and all architectures define pte_offset_kernel() as an entry in the array
of PTEs indexed by the pte_index().
For the most architectures the pte_offset_kernel() implementation relies
on the availability of pmd_page_vaddr() that converts a PMD entry value to
the virtual address of the page containing PTEs array.
Let's move x86 definitions of the PTE accessors to the generic place in
<linux/pgtable.h> and then simply drop the respective definitions from the
other architectures.
The architectures that didn't provide pmd_page_vaddr() are updated to have
that defined.
The generic implementation of pte_offset_kernel() can be overridden by an
architecture and alpha makes use of this because it has special ordering
requirements for its version of pte_offset_kernel().
[rppt@linux.ibm.com: v2]
Link: http://lkml.kernel.org/r/20200514170327.31389-11-rppt@kernel.org
[rppt@linux.ibm.com: update]
Link: http://lkml.kernel.org/r/20200514170327.31389-12-rppt@kernel.org
[rppt@linux.ibm.com: update]
Link: http://lkml.kernel.org/r/20200514170327.31389-13-rppt@kernel.org
[akpm@linux-foundation.org: fix x86 warning]
[sfr@canb.auug.org.au: fix powerpc build]
Link: http://lkml.kernel.org/r/20200607153443.GB738695@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-10-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
