VICUT1(Q,P) is the Kverneland UT1(Q,P) IsoBus universal terminal for agricultural
applications on tractors.
Co-Developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a device-tree definition for the CSI0 MCLK pin,
which can be used for feeding MIPI CSI-2 sensors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
There are two KSZ8081 on the imx6ul-14x14-evk: one has the reset line
controlled by the Q1 output of the 74LV595PW expander, and the other
by the Q2 output.
The KSZ8081 datasheet states that the tsr parameter (Stable supply
voltage (VDDIO, VDDA_3.3) to reset high) to be 10ms minimum and
"After the de-assertion of reset, wait a minimum of 100 µs before
starting programming on the MIIM (MDC/MDIO) interface."
Describe these parameters in the devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently the 74LV595PW GPIO expander is not functional because its OE
pin is not driven low.
Make it funcional by passing the 'enable-gpios' property inside the
GPIO expander node.
After putting the OE pin in low state, the outputs of the 74LV595PW all
go low.
The two KSZ8081 Ethernet PHYs reset lines are driven from the
the GPIO expander and as they remain low, this causes the Ethernet
PHYs not to be detected.
There is one solution to this problem as suggested by Andrew Lunn:
"Some devices will respond to MDIO while held in reset, some don't.
If your PHYs don't you need to add a compatible of the form
ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$ with the PHY ID. The PHY
will then be probed, independent of if it can be found on the bus or
not, and that probing will enable the GPIO."
So pass the "ethernet-phy-id0022.1560" for the KSZ8081 PHYs so that they
both can be functional after 74LV595PW is activated.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO expander SPI chipselect is active low. Mark it as such to avoid
the following warning:
[ 6.839213] gpio@0 enforce active low on chipselect handle
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Ux500 platforms have some memory carveouts set aside for
communicating with the modem and for the initial secure software
(ISSW). These areas are protected by the memory controller
and will result in an external abort if accessed like common
read/write memory.
On the legacy boot loaders, these were set aside by using
cmdline arguments such as this:
mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M
mem_modem=16M@112M mali.mali_mem=32M@128M mem=96M@160M
hwmem=127M@256M mem_issw=1M@383M mem_ram_console=1M@384M
mem=638M@385M
Reserve the relevant areas in the device tree instead. The
"mali", "hwmem", "mem_ram_console" and the trailing 1MB at the
end of the memory reservations in the list are not relevant for
the upstream kernel as these are nowadays replaced with
upstream technologies such as CMA. The modem and ISSW
reservations are necessary.
This was manifested in a bug that surfaced in response to
commit 7fef431be9 ("mm/page_alloc: place pages to tail in __free_pages_core()")
which changes the behaviour of memory allocations
in such a way that the platform will sooner run into these
dangerous areas, with "Unhandled fault: imprecise external
abort (0xc06) at 0xb6fd83dc" or similar: the real reason
turns out to be that the PTE is pointing right into one of
the reserved memory areas. We were just lucky until now.
We need to augment the DB8500 and DB8520 SoCs similarly
and also create a new include for the DB9500 used in the
Snowball since this does not have a modem and thus does
not need the modem memory reservation, albeit it needs
the ISSW reservation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Cc: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/20201213225517.3838501-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX fixes for 5.11:
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
* tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
ARM: imx: fix imx8m dependencies
ARM: dts: tbs2910: rename MMC node aliases
arm64: dts: ls1028a: fix the offset of the reset register
arm64: dts: imx8mn: Fix duplicate node name
ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight
Link: https://lore.kernel.org/r/20210112131224.GI28365@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I didn't touch this code since it served as a platform to introduce
ARMv7-M support to Linux. The only known machine that runs Linux has only
4 MiB of RAM (that originally only exists to hold the display's framebuffer).
There are no known users and no further use foreseeable, so drop the
code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210115155130.185010-2-u.kleine-koenig@pengutronix.de'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The node names for devices using the pwm-leds driver follow a certain
naming scheme (now). Parent node name is not enforced, but recommended
by DT project.
DTC arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
CHECK arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml
/home/alex/build/linux/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml: led-rgb: 'led-blue', 'led-green', 'led-red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+'
From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml
Signed-off-by: Alexander Dahl <post@lespocky.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$',
make it so and fix the following two make dtbs_check warnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
Fixes: ac68793f49 ("ARM: dts: stm32: Add DHCOM based PicoITX board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The AB8505 mixed signal ASIC variant has a die temperature
channel that is missing in the AB8500 variant. Add it to
the DTSI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The setting of VMMCI differs so much between different
boards that we need to handle it on a per-board basis
rather that complicating things by overriding stuff from
the included DTSI:s. Push it down into top-level tree
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the two temperature-monitoring thermistors to the
HREF reference design, defines a thermal zone for the
chassis and sets some reasonable thermal limits.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The different charger nodes in the AB8500 and AB8505
includes was missing the interrupt assignments for the
interrupts necessary to drive the AB8500/AB8505 charging
state machine.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AB8500/AB8505 is providing ADC channels and do so
using the standard property "io-channel-names" not the
mistakenly singular form "io-channel-name".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation for the conversion of the DWC HDMI TX device tree
bindings to YAML, move the HDMI encoder's 'port' nodes under a 'ports'
node. The 'ports' node is optional in the OF graph implementation, but
YAML bindings require it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
to be consistent with kernel versions up to v5.9 (mmc aliases not used here).
usdhc1 is not wired up on this board and therefore cannot be used.
Start mmc aliases with usdhc2.
Signed-off-by: Soeren Moch <smoch@web.de>
Cc: stable@vger.kernel.org # 5.10.x
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wlf,wm8962 driver does not use the clock-names property.
Drop it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the conversion of syscon.yaml minItems for compatibles
was set to 2. Current Rockchip dtsi files only use "syscon" for
QoS registers. Add Rockchip QoS compatibles for rk3288
to reduce notifications produced with:
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201206103711.7465-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the conversion of syscon.yaml minItems for compatibles
was set to 2. Current Rockchip dtsi files only use "syscon" for
QoS registers. Add Rockchip QoS compatibles for rk3066/rk3188
to reduce notifications produced with:
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201206103711.7465-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull ARM SoC fixes from Arnd Bergmann:
"These are a small number of bug fixes that all came in before or
during the merge window, most for the omap platform:
- One boot regression fix for Nokia N9 (OMAP3).
- Two small defconfig changes for omap2, to reflect changes in
drivers
- Warning fixes for DT issues on omap2, picoxcell and bitmap SoCs.
The picoxcell platform will be removed in v5.12, but fixing it
first makes it easier to backport to the fix to stable kernels and
get a clean build with new dtc versions"
* tag 'arm-fixes-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: picoxcell: fix missing interrupt-parent properties
ARM: dts: ux500/golden: Set display max brightness
arm64: dts: bitmain: Use generic "ngpios" rather than "snps,nr-gpios"
ARM: omap2: pmic-cpcap: fix maximum voltage to be consistent with defaults on xt875
ARM: omap2plus_defconfig: enable SPI GPIO
ARM: OMAP2+: omap_device: fix idling of devices during probe
ARM: dts: OMAP3: disable AES on N950/N9
ARM: omap2plus_defconfig: drop unused POWER_AVS option
v5.11-berlin-dts
* tag 'v5.11-berlin-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
ARM: dts: berlin: Use generic "ngpios" rather than "snps,nr-gpios"
ARM: dts: berlin: Fix schema warnings for pwm-leds
Link: https://lore.kernel.org/r/20201211100521.2e6f4faa@xhacker.debian
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
drm-misc-next for v5.12:
UAPI Changes:
- Not necessarily one, but we document that userspace needs to force probe connectors.
Cross-subsystem Changes:
- Require FB_ATY_CT for aty on sparc64.
- video: Fix documentation, and a few compiler warnings.
- Add devicetree bindings for DP connectors.
- dma-buf: Update kernel-doc, and add might_lock for resv objects in begin/end_cpu_access.
Core Changes:
- ttm: Warn when releasing a pinned bo.
- ttm: Cleanup bo size handling.
- cma-helper: Remove prime infix, and implement mmap as GEM CMA functions.
- Split drm_prime_sg_to_page_addr_arrays into 2 functions.
- Add a new api to install irq using devm.
- Update panel kerneldoc to inline style.
- Add DP support to drm/bridge.
- Assorted small fixes to ttm, fb-helper, scheduler.
- Add atomic_commit_setup function callback.
- Automatically use the atomic gamma_set, instead of forcing drivers to declare the default atomic version.
- Allow using degamma for legacy gamma if gamma is not available.
- Clarify that primary/cursor planes are not tied to 1 crtc (depending on possible_crtcs).
- ttm: Cleanup the lru handler.
Driver Changes:
- Add pm support to ingenic.
- Assorted small fixes in radeon, via, rockchip, omap2fb, kmb, gma500, nouveau, virtio, hisilicon, ingenic, s6e63m0 panel, ast, udlfb.
- Add BOE NV110WTM-N61, ys57pss36bh5gq, Khadas TS050 panels.
- Stop using pages with drm_prime_sg_to_page_addr_arrays, and switch all callers to use ttm_sg_tt_init.
- Cleanup compiler and docbook warnings in a lot of fbdev devices.
- Use the drmm_vram_helper in hisilicon.
- Add support for BCM2711 DSI1 in vc4.
- Add support for 8-bit delta RGB panels to ingenic.
- Add documentation on how to test vkms.
- Convert vc4 to atomic helpers.
- Use degamma instead of gamma table in omap, to add support for CTM and color encoding/range properties.
- Rework omap DSI code, and merge all omapdrm modules now that the last omap panel is now a drm panel.
- More refactoring of omap dsi code.
- Enable 10/12 bpc outputs in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/78381a4f-45fd-aed4-174a-94ba051edd37@linux.intel.com
R40 contains deinterlace core compatible to that in H3. One peculiarity
is that RAM gate is shared with CSI1. User manual states it's separate
but that's not true. Shared gate was verified with BSP Linux code check
and with runtime tests (CPU crashed if CSI1 gate was not ungated).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210106181901.1324075-3-jernej.skrabec@siol.net
