Actions Semi ARM DT changes for v5.12:
Updates to the existing S500 ARM SoC. Support has been added for CMU (Clock
Management Unit), Reset controller, DMA, Pinctrl/GPIO, MMC, I2C and SIRQ
(interrupt controller). Since the CMU support is added, the dummy fixed clock
used for the UART controller has been removed for all S500 based boards and
proper UART clock from CMU is used.
Added uSD support and I2C pinctrl configuration for Roseapplepi board based on
S500 SoC. This will make the board boot mainline with a distro from uSD card.
The I2C pinctrl config is added specifically for the PMIC which is currently
under review.
* tag 'actions-arm-dt-for-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/linux-actions:
arm: dts: owl-s500-roseapplepi: Add I2C pinctrl configuration
arm: dts: owl-s500-roseapplepi: Add uSD support
arm: dts: owl-s500: Add SIRQ controller
arm: dts: owl-s500: Add I2C support
arm: dts: owl-s500: Add MMC support
arm: dts: owl-s500: Add pinctrl & GPIO support
arm: dts: owl-s500: Add DMA controller
arm: dts: owl-s500: Add Reset controller
arm: dts: owl-s500: Set CMU clocks for UARTs
arm: dts: owl-s500: Add Clock Management Unit
Link: https://lore.kernel.org/r/20210205050346.GA7619@thinkpad
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX device tree change for 5.12:
- A series from Oleksij Rempel to add i.MX6 based Plymovent, Protonic
and Kverneland boards.
- A series from Andreas Kemnade to improve UART support for ebook
readers.
- A series from Fabio Estevam to update imx6ul-14x14-evk device tree for
adding GPIO expander and camera support.
- A patch set from Lucas Stach to improve ZII RDU2 support, enabling
WDOG, tuning I2C drive-strength, RMI4 and UCS1002 ALERT.
- Other small and random updates on various boards.
* tag 'imx-dt-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (37 commits)
ARM: dts: imx6: RDU2: adjust audio devices nomenclature
ARM: dts: imx6: RDU2: only trigger IRQ on falling edge ucs1002 ALERT pin
ARM: dts: imx6: RDU2: enable RMI4 reduced reporting
ARM: dts: imx6: RDU2: reduce i2c drive-strength
ARM: dts: imx6: rdu2: enable WDOG1
ARM: dts: imx6-sr-som: increase at8035 PHY gigabit Tw parameter
ARM: dts: imx6: add wakeup support via magic packet
firmware: imx: select SOC_BUS to fix firmware build
arm64: dts: imx8mp: Correct the gpio ranges of gpio3
ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
ARM: dts: imx: e60k02: add second uart
ARM: dts: imx6sl-tolino-shine3: correct console uart pinmux
ARM: dts: imx6sl-tolino-shine2hd: add second uart
ARM: dts: imx6sl-tolino-shine2hd: correct console uart pinmux
ARM: imx: build suspend-imx6.S with arm instruction set
ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset
ARM: dts: add Kverneland TGO board
ARM: dts: add Kverneland UT1, UT1Q and UT1P
ARM: dts: imx6ul-14x14-evk: Add camera support
ARM: dts: imx6ul-14x14-evk: Describe the KSZ8081 reset
...
Link: https://lore.kernel.org/r/20210204120150.26186-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: dts: amlogic updates for v5.12
- add thermal zones with cooling configuration
* tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8b: add the thermal-zones with cooling configuration
ARM: dts: meson8: add the thermal-zones with cooling configuration
ARM: dts: meson: add the ADC thermal sensor to meson.dtsi
ARM: dts: meson: move iio-hwmon for the SoC temperature to meson.dtsi
Link: https://lore.kernel.org/r/7ho8h12bto.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Without DT aliases, the numbering of mmc interfaces is unpredictable.
Adding them makes it possible to refer to devices consistently. The
popular suggestion to use UUIDs obviously doesn't work with a blank
device fresh from the factory.
See commit fa2d0aa969 ("mmc: core: Allow setting slot index via
device tree alias") for more discussion.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The 32-bit Amlogic Meson SoCs embed an ARC processor in the Always-On
power domain which is typically used for managing system suspend. The
memory for this ARC core is taken from the AHB SRAM area. Depending on
the actual SoC a different ARC core is used:
- Meson6 and earlier: some ARCv1 ISA based core (probably an ARC625)
- Meson8 and later: an ARC EM4 (ARCv2 ISA) based core
Add the device-tree node for this remote-processor along with the
required SRAM sections, clocks and reset-lines. Also use the
SoC-specific compatible string to manage any differences (should
they exist).
On Meson8, Meson8b and Meson8m2 the "secbus2" IO region is needed as
some bits need to be programmed there. Add this IO region for those
SoCs as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20210102205904.2691120-6-martin.blumenstingl@googlemail.com
One fix for a phy-mode ethernet issue, and one to fix the display output on
SoCs with the Display Engine 2
* tag 'sunxi-fixes-for-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode
soc: sunxi: mbus: Remove DE2 display engine compatibles
Link: https://lore.kernel.org/r/f8298059-f9ca-43b4-9e29-35bc0e0c9b15.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit c17e9377aa.
The lpc32xx clock driver is not able to actually change the PLL rate as
this would require reparenting ARM_CLK, DDRAM_CLK, PERIPH_CLK to SYSCLK,
then stop the PLL, update the register, restart the PLL and wait for the
PLL to lock and finally reparent ARM_CLK, DDRAM_CLK, PERIPH_CLK to HCLK
PLL.
Currently, the HCLK driver simply updates the registers but this has no
real effect and all the clock rate calculation end up being wrong. This is
especially annoying for the peripheral (e.g. UARTs, I2C, SPI).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20210203090320.GA3760268@piout.net'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BPi Pro needs TX and RX delay for Gbit to work reliable and avoid high
packet loss rates. The realtek phy driver overrides the settings of the
pull ups for the delays, so fix this for BananaPro.
Fix the phy-mode description to correctly reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: 10662a33dc ("ARM: dts: sun7i: Add dts file for Bananapro board")
Signed-off-by: Hermann Lauer <Hermann.Lauer@uni-heidelberg.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210128111842.GA11919@lemon.iwr.uni-heidelberg.de
This adds support for the power button attached to the Embedded Controller
on a Dell Wyse 3020 "Ariel" board.
However, while the EC itself is controlled via I2C, the input capability
for the power button acts as a separate device attached to the SPI, hence
it has a separate device node.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20210121034130.1381872-11-lkundrak@v3.sk'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Drop the linux,usable-memory properties; the schema is unhappy about
them.
They've been cargo-culted from Open Firmware and I don't know what
purpose they serve. Perhaps they are meant to provide the OFW runtime.
In that case it's still okay to drop them from here; OFW is welcome to add
it upon boot.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20210121034130.1381872-6-lkundrak@v3.sk'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Drop the linux,usable-memory properties; the schema is unhappy about
them:
mmp2-olpc-xo-1-75.dt.yaml: /: memory: False schema does not allow
{'linux,usable-memory': [[0, 528482304]],
'available': [[847872, 519245824, 4096, 782336]],
'reg': [[0, 536870912]], 'device_type': ['memory']}
They've been cargo-culted from Open Firmware and I don't know what
purpose they serve. Perhaps they are meant to provide the OFW runtime.
In that case it's still okay to drop them from here; OFW is welcome to add
it upon boot.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20210121034130.1381872-5-lkundrak@v3.sk'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mvebu dt for 5.12 (part 1)
Improve LED and fan support on Helios4 boad (Armada 388 based)
Add ECC configuration for Linksys board (Aramda 385 based)
* tag 'mvebu-dt-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: armada388-helios4: assign pinctrl to each fan
ARM: dts: armada388-helios4: assign pinctrl to LEDs
ARM: dts: armada-385-linksys: fix usage with newer devices
Link: https://lore.kernel.org/r/87sg6fn49o.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.12, please pull the following:
- Dave adds a proper compatile string for the DSI1 panel on 2711
(Raspberry Pi 4) to permit adequate driver differentiation
- Nicolas declares reserved memory regions filed by the Rasbperry Pi
bootloader to indicate the running system configuration
- Maxime declares the BSC (HDMI I2C controller) and CEC interrupt
controllers
- Stanislav fixes a tab vs. space issue in the BCM21664 DTS
* tag 'arm-soc/for-5.12/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2711: Add the CEC interrupt controller
ARM: dts: bcm21664: Replace spaces with a tab
ARM: dts: bcm2711: Add the BSC interrupt controller
ARM: dts: bcm2711: Add reserved memory template to hold firmware configuration
ARM: dts: bcm2711: Use compatible string for BCM2711 DSI1
Link: https://lore.kernel.org/r/20210131221721.685974-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The R_INTC block controls more than just the NMI, and it is a different
hardware block than the NMI INTC found in some other Allwinner SoCs, so
the label "nmi_intc" is inaccurate. Name it "r_intc" to match the
compatible and to match the few references in the vendor documentation.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210118055040.21910-6-samuel@sholland.org
While the USB PHY Device Tree mandates that the name of the ID detect pin
should be usb0_id_det-gpios, a significant number of device tree use
usb0_id_det-gpio instead.
This was functional because the GPIO framework falls back to the gpio
suffix that is legacy, but we should fix this.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-12-maxime@cerno.tech
This adds a "HPA1" prefix to the amplifiers on both audio cards, this is
done in order to get more consistency for userspace running on RDU2 and
RDU3, where we have two amplifiers on a single card device in the "Zest"
configuration.
Also adjust the card names to the new standard expected by userspace.
Signed-off-by: Cory Tusar <cory.tusar@zii.aero>
[adjusted commit message]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ALERT signaling happens on the falling edge of the signal, as rising
edge doesn't really have any notion, as it may happen much later (due to
shared IRQ line) or too early if the chip resolves the fault itself. So
only trigger the IRQ on the edge we are actually interested in.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
