Modify usart 2 & 3 pins to allow wake up from low power mode while the
hardware flow control is activated. UART RTS pin need to stay configure
in idle mode to receive characters in order to wake up.
Fixes: 842ed898a7 ("ARM: dts: stm32: add usart2, usart3 and uart7 pins in stm32mp15-pinctrl")
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
According to the datasheet PA7 can be set to either function A, B or
C (see table 6-2 of DS60001579D). The previous value would permit just
configuring with function C.
Signed-off-by: Federico Pellegrin <fede@evolware.org>
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Cc: <stable@vger.kernel.org> # 5.6+
Cc: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fix the phy address to 7 for Ethernet PHY on SAMA5D27 SOM1. No
connection established if phy address 0 is used.
The board uses the 24 pins version of the KSZ8081RNA part, KSZ8081RNA
pin 16 REFCLK as PHYAD bit [2] has weak internal pull-down. But at
reset, connected to PD09 of the MPU it's connected with an internal
pull-up forming PHYAD[2:0] = 7.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Fixes: 2f61929eb1 ("ARM: dts: at91: at91-sama5d27_som1: fix PHY ID")
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # 4.14+
We can now probe devices with ti-sysc interconnect driver and dts data.
Let's drop the related platform data and custom ti,hwmods dts property.
As we're just dropping data, and the early platform data init is based on
the custom ti,hwmods property, we want to drop both the platform data and
ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts data.
Let's drop the related platform data and custom ti,hwmods dts property.
As we're just dropping data, and the early platform data init is based on
the custom ti,hwmods property, we want to drop both the platform data and
ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation for probing l3 with simple-pm-bus and genpd, we must move
l3 noc to a separate node. This is to prevent omap_l3_noc.c driver from
claiming the whole l3 instance before simple-pm-bus has a chance to probe.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need mmio-sram early for omap4_sram_init() for IO barrier init, and
will be moving l3 interconnect to probe with simple-pm-bus that probes
at module_init() time. So let's move mmio-sram out of l3 to prepare for
that.
Otherwise we will get the following after probing the interconnects with
simple-pm-bus:
omap4_sram_init:Unable to get sram pool needed to handle errata I688
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Note that the old sysc register offset is wrong, the real offset is at
0x1100 as listed in TRM for SATA_SYSCONFIG register. Looks like we've been
happily using sata on the bootloader configured sysconfig register and
nobody noticed. Also the old register range for SATAMAC_wrapper registers
is wrong at 7 while it should be 8. But that too seems harmless.
There is also an L3 parent interconnect range that we don't seem to be
using. That can be added as needed later on.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" property to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" property to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" property to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe interconnects with simple-pm-bus and genpd.
Let's drop the legacy data along with the ti,hwmods property and flip
over to using simple-pm-bus instead of simple-bus.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts data.
Let's drop the related platform data and custom ti,hwmods dts property.
As we're just dropping data, and the early platform data init is based on
the custom ti,hwmods property, we want to drop both the platform data and
ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts data.
Let's drop the related platform data and custom ti,hwmods dts property.
As we're just dropping data, and the early platform data init is based on
the custom ti,hwmods property, we want to drop both the platform data and
ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts data.
Let's drop the related platform data and custom ti,hwmods dts property.
As we're just dropping data, and the early platform data init is based on
the custom ti,hwmods property, we want to drop both the platform data and
ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's configure omap4 l3 for power-domain and clocks in preparation for
starting to use simple-pm-bus. We will flip over to using simple-pm-bus
later on after dropping the legacy data for all the devices on l3
interconnect.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
Signed-off-by: Tony Lindgren <tony@atomide.com>
In preparation for probing l3 with simple-pm-bus and genpd, we must move
l3 noc to a separate node. This is to prevent omap_l3_noc.c driver from
claiming the whole l3 instance before simple-pm-bus has a chance to probe.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need mmio-sram early for omap4_sram_init() for IO barrier init, and
will be moving l3 interconnect to probe with simple-pm-bus that probes
at module_init() time. So let's move mmio-sram out of l3 to prepare for
that.
Otherwise we will get the following after probing the interconnects with
simple-pm-bus:
omap4_sram_init:Unable to get sram pool needed to handle errata I688
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" property to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" property to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" property to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Let's also use GIC_SPI and IRQ_TYPE_LEVEL_HIGH defines while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure power-domain for omap4 dts iss in preparation to
probing devices with simple-pm-bus and genpd.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Configure power-domain for omap4 dts gfx in preparation to
probing devices with simple-pm-bus and genpd.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe interconnects with device tree only configuration using
simple-pm-bus and genpd.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts data.
Let's drop the related platform data and custom ti,hwmods dts property.
As we're just dropping data, and the early platform data init is based on
the custom ti,hwmods property, we want to drop both the platform data and
ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Note that the old sysc register offset is wrong, the real offset is at
0x1100 as listed in TRM for SATA_SYSCONFIG register. Looks like we've been
happily using sata on the bootloader configured sysconfig register and
nobody noticed. Also the old register range for SATAMAC_wrapper registers
is wrong at 7 while it should be 8. But that too seems harmless.
There is also an L3 parent interconnect range that we don't seem to be
using. That can be added as needed later on.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts data.
Let's drop the related platform data and custom ti,hwmods dts property.
As we're just dropping data, and the early platform data init is based on
the custom ti,hwmods property, we want to drop both the platform data and
ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
