A test with the command below gives this error:
/arch/arm/boot/dts/rk3036-evb.dt.yaml:
pwm@20050030: clock-names: ['pwm'] is too short
Devices with only one PWM clock use it to both to derive the functional
clock for the device and as the bus clock. The driver does not need
"clock-names" to get a handle, so remove them all.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/pwm/pwm-rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The "amba" bus nodes wrapping all the DMA-330 nodes serve no useful
purpose, and certainly bear no relation at all to the actual underlying
interconnect topology. They appear to be cargo-cult copying from a
design misstep in the very early days of FDT adoption on ARM, which was
righted with the "arm,primecell" compatible, and the last trace of the
idea finally purged by commit 2ef7d5f342 ("ARM, ARM64: dts: drop
"arm,amba-bus" in favor of "simple-bus"").
As such, they can simply be removed and the DMA-330 nodes fitted into
the normal sort order.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/e682edd25133bde2ed8198138febc90071530a51.1611186142.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
/arch/arm/boot/dts/rk3288-tinker.dt.yaml:
thermal-zones: 'cpu_thermal', 'gpu_thermal', 'reserve_thermal'
do not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Rename Rockchip rk3288 thermal subnodes
so that it ends with "-thermal"
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
thermal/thermal-zones.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210117150953.16475-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the conversion of syscon.yaml minItems for compatibles
was set to 2. Current Rockchip dtsi files only use "syscon" for
QoS registers. Add Rockchip QoS compatibles for rk3288
to reduce notifications produced with:
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201206103711.7465-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3288-tinker.dt.yaml: tsadc: otp-gpio:
{'phandle': [[54]], 'rockchip,pins': [[0, 10, 0, 118]]}
is not of type 'array'
'gpio' is a sort of reserved nodename and should not be used
for pinctrl in combination with 'rockchip,pins', so change
nodes that end with 'gpio' to end with 'pin' or 'pins'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/
dtschema/schemas/gpio/gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200524160636.16547-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
An experimental test with the command below gives
for example this error:
arch/arm/boot/dts/rk3036-evb.dt.yaml: i2s@10220000:
'#address-cells', '#size-cells'
do not match any of the regexes: 'pinctrl-[0-9]+'
'#address-cells' and '#size-cells' are not a valid property
for i2s nodes, so remove them.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-i2s.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200311162524.19748-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current dts files with 'i2s' nodes are manually verified.
In order to automate this process rockchip-i2s.txt
has to be converted to yaml. In the new setup dtbs_check with
rockchip-i2s.yaml expect clocks and clock-names values
in the same order. Fix this for some older Rockchip models.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-i2s.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200311162524.19748-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rv1108-evb.dt.yaml: usb@30140000:
'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
'clock-names' is not a valid property name for usb_host nodes with
compatible string 'generic-ehci', so remove them.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/usb/generic-ehci.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312171441.21144-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current dts files with 'spdif' nodes are manually verified.
In order to automate this process rockchip-spdif.txt
has to be converted to yaml. In the new setup dtbs_check with
rockchip-spdif.yaml expect clocks and clock-names values
in the same order. Fix this for some older Rockchip models.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sound/rockchip-spdif.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200312172240.21362-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: amba: $nodename:0:
'amba' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
AMBA is a open standard for the connection and
management of functional blocks in a SoC.
It's compatible with 'simple-bus', so fix this error
by adding 'bus' to all Rockchip 'amba' nodes.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/
schemas/simple-bus.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200302153047.17101-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example these errors:
arch/arm/boot/dts/rk3288-evb-act8846.dt.yaml:
bus_intmem@ff700000: $nodename:0: 'bus_intmem@ff700000'
does not match '^sram(@.*)?'
arch/arm/boot/dts/rk3288-evb-rk808.dt.yaml:
bus_intmem@ff700000: $nodename:0: 'bus_intmem@ff700000'
does not match '^sram(@.*)?'
'rockchip-pmu-sram.txt' inherit properties from 'sram.yaml'.
Fix this error by adding 'sram' to the bus_intmem nodename
in 'rk3288.dtsi'. But 'sram' is also a node name already in use.
To prevent confusion rename it to 'pmu_sram'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/sram/sram.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200228155354.27206-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Current dts files with 'dwmmc' nodes are manually verified.
In order to automate this process rockchip-dw-mshc.txt
has to be converted to yaml. In the new setup
rockchip-dw-mshc.yaml will inherit properties from
mmc-controller.yaml and synopsys-dw-mshc-common.yaml.
'dwmmc' will no longer be a valid name for a node,
so change them all to 'mmc'
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200115185244.18149-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This just adds in another field of what's stored in the e-fuse on
rk3288. Though I can't personally promise that every rk3288 out there
has the CPU ID stored in the eFuse at this location, there is some
evidence that it is correct:
- This matches what was in the Chrome OS 3.14 branch (see
EFUSE_CHIP_UID_OFFSET and EFUSE_CHIP_UID_LEN) for rk3288.
- The upstream rk3399 dts file has this same data at the same offset
and with the same length, indiciating that this is likely common for
several modern Rockchip SoCs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20190919142611.1.I309434f00a2a9be71e4437991fe08abc12f06e2e@changeid
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the "unwedge" pinctrl entries introduced by a recent dw_hdmi
change that can unwedge the dw_hdmi i2c bus in some cases. It's
expected that any boards using this would add:
pinctrl-names = "default", "unwedge";
pinctrl-0 = <&hdmi_ddc>;
pinctrl-1 = <&hdmi_ddc_unwedge>;
Note that this isn't added by default because some boards may choose
to mux i2c5 for their DDC bus (if that is more tested for them).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is the same as the other PWMs on this SoC and uses 3 cells.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NPLL is the only safe way to generate 500 MHz for the GPU. The
downstream Chrome OS 3.14 kernel ('official' kernel for veyron
devices) re-purposes NPLL to HDMI and hence disables the OPP for
the GPU (see https://crrev.com/c/1574579). Disable it here as well
to keep in sync and avoid problems in case someone decides to
re-purpose NPLL.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[moved from veyron to general rk3288, as tying up the NPLL for a
not-that-helpful opp (not really fast but will still generate
quite a bit of heat) doesn't make so much sense when it will
keep us from supporting other display modes in the future]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently the CPUs are used as cooling devices of the rk3288 GPU
thermal zone. The CPUs are also configured as cooling devices in the
CPU thermal zone, which indirectly helps with cooling the GPU thermal
zone, since the CPU and GPU temperatures are correlated on the rk3288.
Configure the ARM Mali Midgard GPU as cooling device for the GPU
thermal zone instead of the CPUs.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Mali GPU of the rk3288 can be used as cooling device, add
a #cooling-cells entry for it.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is similar to commit e6186820a7 ("arm64: dts: rockchip: Arch
counter doesn't tick in system suspend"). Specifically on the rk3288
it can be seen that the timer stops ticking in suspend if we end up
running through the "osc_disable" path in rk3288_slp_mode_set(). In
that path the 24 MHz clock will turn off and the timer stops.
To test this, I ran this on a Chrome OS filesystem:
before=$(date); \
suspend_stress_test -c1 --suspend_min=30 --suspend_max=31; \
echo ${before}; date
...and I found that unless I plug in a device that requests USB wakeup
to be active that the two calls to "date" would show that fewer than
30 seconds passed.
NOTE: deep suspend (where the 24 MHz clock gets disabled) isn't
supported yet on upstream Linux so this was tested on a downstream
kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The "host" USB port on rk3288 has a hardware errata where we've got to
assert a PHY reset whenever we see a remote wakeup. Add that quirk
property to the device tree.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Let's hook up the resets to the three USB PHYs on rk3288 as per the
bindings. This is in preparation for a future patch that will set the
"snps,reset-phy-on-wake" on the host port.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The value was determined with the following method:
- take CPUs 1-3 offline
- for each OPP
- set cpufreq min and max freq to OPP freq
- start dhrystone benchmark
- measure CPU power consumption during 10s
- calculate Cx for OPPx
- Cx = (Px - P1) / (Vx²fx - V1²f1) [1]
using the following units: mW / Ghz / V [2]
- C = avg(C2, ..., Cn)
[1] see commit 4daa001a17 ("arm64: dts: juno: Add cpu
dynamic-power-coefficient information")
[2] https://patchwork.kernel.org/patch/10493615/#22158551
FTR, these are the values for the different OPPs:
freq (kHz) mV Px (mW) Cx
126000 900 39
216000 900 66 370
312000 900 95 372
408000 900 122 363
600000 900 177 359
696000 950 230 363
816000 1000 297 361
1008000 1050 404 362
1200000 1100 528 362
1416000 1200 770 377
1512000 1300 984 385
1608000 1350 1156 394
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
They are pointless. As dtc points out:
Warning (avoid_unnecessary_addr_size):
/mipi@ff960000:
unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Let's remove them.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The device tree compiler yells like this:
Warning (unit_address_vs_reg):
/gpu-opp-table/opp@100000000:
node has a unit name, but no reg property
Let's match the cpu opp node names and use a dash.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
It can be seen that 0xffb40000 < 0xffc01000, thus efuse comes first.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The following message can be seen during boot:
rockchip-thermal ff280000.tsadc: Missing rockchip,grf property
Fix this by adding rockchip,grf property to tsadc node.
The warning itself is not relevant on rk3288 right now, as the
tsadc doesn't need to set GRF-values at this point and only newer
variants do.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The following error can be seen during boot:
of: /cpus/cpu@501: Couldn't find opp node
Change cpu nodes to use operating-points-v2 in order to fix this.
Fixes: ce76de9846 ("ARM: dts: rockchip: convert rk3288 to operating-points-v2")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the Video Processing Unit node for RK3288 SoC.
Fix the VPU IOMMU node, which was disabled and lacking
its power domain property.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, OPP, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[follow conversion to operating-points-v2]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Operating points need to be present in each cpu core using it, not only
the first one. With operating-points-v1 this would require duplicating
this table into each cpu node.
With opp-v2 we can share the same table on all nodes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Update all 32bit rockchip devicetree files to use SPDX-License-Identifiers.
All files except rk3288-veyron-analog-audio.dtsi (which is GPL 2.0 only)
claim to be GPL and X11 while the actual license text is MIT. Use the
MIT SPDX tag for them.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add clocks in iommu nodes, since we are going to control clocks in
rockchip iommu driver.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
dtc now gives the following warning:
arch/arm/boot/dts/rk3288-tinker.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /hdmi@ff980000 or bad phandle (referred from sound-dai[0])
Add the missing #sound-dai-cells property.
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The interrupts property in the iep-IOMMU node for the rk3288 dts file has a
spurious extra cell causing a dtc warning:
Warning (interrupts_property): interrupts size is (16), expected multiple of 12 in /iommu@ff900800
Remove the extra cell.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The CEC line can be routed to two possible pins. Define those pins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The dw-hdmi block needs the cec clk for the rk3288. Add it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull "second round of Rockchip dts32 changes for 4.14" from Heiko Stübner:
A lot of attention for the rv1108 soc targetted at media-processing
(usb, operating points, spi, pwm, adc, watchdog, i2c and devices for
its evb).
RK3228/3229 gets iommu and spi nodes. Similar to the rk3288 which
also gets some more iommu nodes as well as getting converted to 64
bit addresses due to wanting to address more than 4GB of memory
via LPAE.
* tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: rockchip: add cpu power supply for rv1108 evb
ARM: dts: rockchip: add cpu opp table for rv1108
ARM: dts: rockchip: add rk322x iommu nodes
ARM: dts: rockchip: add accelerometer bma250e dt node for rv1108 evb
ARM: dts: rockchip: add pmic rk805 dt node for rv1108 evb
ARM: dts: rockchip: add pwm backlight for rv1108 evb
ARM: dts: rockchip: add pwm dt nodes for rv1108
ARM: dts: rockchip: add spi dt node for rv1108
ARM: dts: rockchip: add saradc support for rv1108
ARM: dts: rockchip: add watchdog dt node for rv1108
ARM: dts: rockchip: add i2c dt nodes for rv1108
clk: rockchip: fix up indentation of some RV1108 clock-ids
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
clk: rockchip: add more clk ids for rv1108
ARM: dts: rockchip: add more iommu nodes on rk3288
ARM: dts: rockchip: convert rk3288 device tree files to 64 bits
ARM: dts: rockchip: add spi node and spi pinctrl on rk3228/rk3229
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
