It turned out DMIC interface wasn't enabled/disabled runtime for active
DMIC route in the rt5640 codec driver anymore after commit
71d97a7943 ("ASoC: rt5640: Use the platform data for DMIC settings").
Since DMIC interface must be enabled explicitly either by passing platform
data to rt5640 codec driver or by calling new rt5640_dmic_enable() this
patch adds a DMI quirk flag that is used to conditionally enable DMIC
interface during sound card init time.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asus T100 internal microphone is not digital but analogue connected to IN1P
pin of the RT564x codec with shared bias between internal and headset
microphones. Because of this there is need to have machine specific DAPM
routes in byt-rt5640.
Add handling for them with the help of DMI quirk that is used to add custom
routes in addition to common. Because "Internal Mic" connected to DMIC1 is
not common to all move it as a default custom route when there is no match
in quirk table.
Custom "Internal Mic" -> "IN1P" with MICBIAS1 route is added for Asus T100.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I tested couple byt-rt5640 based platforms and they have single-ended
headset microphone connection to IN2P only. I guess IN2N was either defined
by accident or some early platform had floating ground for headset. It's
better to remove IN2N and add a custom route for such a platform if needed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All byt-max98090 audio connections are known and described in DAPM routing
table. Set the fully_routed flag in order to disable unused codec pins.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we have PCM (FE/BE) opened or DAPM widgets triggered we need power
up/down DSP accordingly. The DSP will do ref count of these requests
i.e. link these runtime_get/put calls of DSP
Also fix some preexisting spacing error.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add support for various modules like eq etc for mrfld DSP.
All these modules will be exposed to usermode as bytes controls.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For internal stream i.e. BE we have don't need trigger ops as that
would be handled by DAPM for us in subsequent patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The sst-haswell-pcm driver registers both a snd_soc_component and a
snd_soc_platform and expects that the DAPM widgets for the DAIs registered by
component are added to the DAPM context of the platform. This requires us to
have a hack in the ASoC core which does so. Moving the DAPM elements over to
the component allows us to remove this hack.
While we are at it also move the controls over to the component. The controls
don't need the platform for anything other than snd_soc_platform_get_drvdata(),
this can easily be replaced by snd_soc_component_get_drvdata(). As the long
term goal is to register only a single component this is a step in the right
direction.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Resource allocations should happen in driver probe callback rather than in
snd_soc_platform probe functions. Especially if the resource is device
managed. The snd_soc_* probe/remove functions are mainly intended to be used
for things that require the component to be already bound to a card.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also pass sst device as an argument to function pointer prototypes of
compr_ops. This will be used to derive sst driver context.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We define the DSP commands,structures here which will be used to send the IPCs
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
sst_ops need to use the sst driver context. So pass sst device as argument,
which can be used to retrieve sst context.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using a byte control interface instead of generic_params ioctl.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Only update the stream when the IPC message type matches stream type.
Signed-off-by: Paweł Piskorski <pawel.piskorski@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make sure we dont issue IPC when we are processing a response.
Signed-off-by: Paweł Piskorski <pawel.piskorski@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes a bug where we dont delete the current message when an
IPC message timeout occurs.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dependency to DW_DMAC for broadwell machine, which
have built in DW dma engines.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Platform data may be null during platform_device_add. Allocate platform
data before using.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Check ops pointer members before we can derefference them.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add some debugging info to help with Dx state debug.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add trace notification of IPC stream reset.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add some register definitions for other shim register bits.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
HMDC is the correct naming for this register.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for Broadwell based machines with SST DSP audio.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Jie Yang <yang.jie@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update FW version readback. IPC_GLB_GET_FW_VERSION reads back
the ABI version whilst the release version is in the mailbox.
Update to use mailbox version for info logging.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The sst-haswell-dsp.c is an ACPI independent file, this patch removes
ACPI header files for it.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This interface will be used by subsequent patches to set/get parameters from DSP
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DSP returns error codes for IPC return so add them in driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
the shim registers start and end can be useful while parsing the shim addresses,
so add these
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge D-SRAM0 D-SRAM1 D-SRAM2 to D-SRAM, for wild cat point ADSP mem regions.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dummy read after each block enable, to workaround
SRAM write missing bytes issue.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This change removes unsupported formats from System,
Capture and Loopback FE DAIs.
Also it fixes S24_LE support on all DAIs.
While at this fix 24 bit flag for BYT as well.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Kernel should not enable/disable speakers and digital microphone whenever
jack is inserted/removed. This is more use-case than kernel specific
decision. For instance one may want to play VoIP ring tones using both
speakers and headphone but play music only from one of them.
Because of above reason remove "Ext Spk" and "Int Mic" update when jack
state is changed. Also this update was illogical anyway: "Ext Spk" was
enabled when jack was inserted and disabled when jack was removed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It turned out there is no need to enable microphone detection in MAX98090
codec. Headset microphone is anyway detected by a GPIO signal from another
chip and headset button presses cannot be detected either because a signal
needed for it is not connected.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pass actual jack type bitmask to snd_soc_jack_new() in order to report
also microphone detections and not only headphone. While at it change also
jack name and pass also SND_JACK_LINEOUT type.
Reported-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Headset jack has only mono microphone input.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mic detect GPIO is active low when headset microphone is detected. Found
both by debugging and checking the schematics.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move "MICBIAS" as a supply widget to "Headset Mic" instead of keeping it
between input pin "IN34" and "Headset Mic".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As added in previosu patch along with stream to piep conversion si required for
compressed audio too
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merrifield DSP used various pipelines to identify the streams and processing
modules. Add these defination in the pcm driver and also add a table for device
entries to firmware pipeline id conversion
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Tis will be used to add table based support for pcm front ends in subsequent
patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This will be used to update current driver as well as in support for the mrfld
patches
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now the DSP is capable of reporting the delay, report it to upper layers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
