This patch adds support to gspca for the Winbond W9967CF and W9968CF
camera's. This is mostly a port of the existing v4l1 driver to gspca
(making it v4l2). But this also features fixes to the bitbanging i2c code
(send a nack not an ack after reading the last byte of a transfer), which
gets rid of the weird errors which were being seen there, and of
the smbus_refresh() hack to get around these errors.
Also the vstart settings have been tweaked to work with different
frequency filter settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for TEF6862 Car Radio Enhanced Selectivity Tuner.
It's implemented as a subdev, supporting checking signal strength
and setting and getting frequency.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the I2C device provides an interrupt it is registered and the
standard
is updated via interrupts rather than polling.
Since I2C communication is needed, the interrupt handler fires off a
work which will check the new standard, and store it in the internal
structure.
To handle mutual exclusion a mutex is introduced.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch defines the probe and remove function as __devinit and __devexit.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for settings the input standard of the ADV7180.
When the input standard is set there is no use to ask the
chip for standard, therefore it is cached in the driver.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support to the ADV7180 driver to check the input
status.
Since the status is held in the same register as the input standard
a small restructuring of the code is done to reuse the code for
reading the register
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds the device IDs and driver linking to allow the Asus Europa DVB-T
card to operate with these drivers.
The device has a SAA7134 chipset with a TD1316 Hybrid Tuner.
All inputs work on the card including switching between DVB-T and
Analogue TV, there is also no IR with this card.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Danny Wood <danwood76@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The definition of tvaudio_tuner_ops initializes the s_tuner field twice.
It appears that the second case should initialize the g_tuner field.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the image size (bytesperline*height) is not multiple
of PAGE_SIZE, v4l2 rounded the required buffer size to
be multiple of PAGE_SIZE. This prevented user space
to store images directly into userptr buffers which were
not multiple of PAGE_SIZE. This constraint is removed.
The start address is still assumed to be required
page-aligned, ie., when v4l2 allocates mmap buffers,
the offset between different buffers is page-aligned.
Signed-off-by: Tuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DVBS2API introduced two new ioctls that allows changing/getting details about newer
video standards like DVB-S2 and ISDB-T. There are lots of thing to do in this chapter,
but, for now, just add a session there, in order to allow make to not complain about
undefined symbol.
With this patch, all ioctls at the frontend.h API were somehow documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll need to add the documentation for FE_[GET|SET]_PROPERTY that
is not specific to isdb-t. Instead of doing it at frontend.xml,
it is better to have a separate session for it. Also, isdbt.xml assumes
that those ioctls were already introduced, and documents several exisiting
properties. So, better to just rename it and add the documentation for it,
together with each existing property there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While this ioctl should not be used, and is a good canditate for
Documentation/feature-removal-schedule.txt, while it is on kernel,
it needs to be documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds linux/dvb/frontend.h header file at DocBook, and creates cross-references
for the frontend ioctls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all sessions id's for frontend ioctls to match ioctl name and
add the proper cross-link references for those ioctls.
This also helps to identify what ioctls are missing specs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default streaming control timeout was found by Ondrej Zary to be too low
for some Logitech webcams. With kernel 2.6.22 and newer they would timeout
during initialization unles the audio function was initialized before the
video function.
Add a module parameter to set the streaming control timeout and increase the
default value from 1000ms to 3000ms to fix the above problem.
Thanks to Ondrej Zary for investigating the issue and providing an initial
patch.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At least one 5986:0241 webcam model includes vendor-specific descriptors
at the end of its streaming interface descriptors. Print an information
UVC_TRACE_DESCR message and try to continue parsing the descriptors
rather than bailing out with an error.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch sets stream->urb_size as psize*npackets
before calling uvc_alloc_urb_buffers, which may fix
a possible failure of usb_buffer_free in case usb_buffer_alloc
returns NULL. The patch is based on the ideas below:
1,If usb_buffer_alloc can't allocate a buffer sucessfully,
uvc_free_urb_buffers will be called to free the allocated
buffers, and stream->urb_size is required to be passed to
usb_buffer_free;
2,uvc_free_urb_buffers can reset stream->urb_size.
This patch is against linux-v2.6.31-next-20090926.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The uvcvideo driver has a driver-wide lock and a reference count to protect
against a disconnect/open race. Now that videodev handles the race itself,
reference-counting in the driver can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dismiss privileges on the file handle when calling VIDIOC_REQBUFS with a
buffer count of 0. This allows applications to release the streaming
permissions on the file handle without closing it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_TRY_FMT ioctl doesn't interfere with video streaming and thus
should succeed on an unprivileged file handle.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the trace level for messages related to video URB buffers allocation and
alternate setting selection.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return minimum, maximum and step set to 0 without querying the hardware.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were various "if (sensor == foo)" pieces of code inside ov519.c,
move these bits to the sensor specific init functions, where they
belong.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gscpa_ov519: add support for the ovfx2 bridge
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the OV2610 and OV3610 sensors to the gspca
ov519 subdriver. This is a preparation patch for adding ovfx2 bridge
support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CIF sensor type 1 exposure setting got clamped at 300, as settings below
300 do not work well (and do work for the other sensors). This patch
scales the 0-4095 range to 300-4095 instead of ignoring changes between
300, avoiding have a part of the control range where nothing happens.
This is esp. important for software autogain as done by libv4l.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While checking all gspca sub drivers pkt_scan functions for a bug I found in
1 of them (and after checking also in another), I noticed a bug in the
gspca_sq905c work queue function, once it has decided to start discarding a
frame because the application is not reading fast enough (and thus returning
buffers to fill fast enough), it never stops discarding.
This patch fixes this by simply completely removing the "discarding"
variable, if we need to discard the current frame because there is no buffer
to store it, the "frame" pointer will be NULL, so that is all we need to
check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While checking all gspca sub drivers pkt_scan functions for a bug I found in
1 of them (and after checking also in another), I noticed a bug in the
gspca_jeilinj work queue function, once it has decided to start discard a
frame because the application is not reading fast enough (and thus returning
buffers to fill fast enough), it never stops discarding.
This patch fixes this by simply completely removing the "discarding"
variable, if we need to discard the current frame because there is no buffer
to store it, the "frame" pointer will be NULL, so that is all we need to
check.
I've also moved the gspca_get_i_frame() call and the writing of the jpg
header to the buffer to after the first usb_bulk_msg() call, as we don't
need it before that, and that will give the app slightly more time to
queue a buffer for us to fill.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improve (and also simplify :) gspca_mr97310a: VGA sensor type detection.
As it was still failing on some machines (not with some cams, but on
some machines interesting enough).
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Remove use of unneeded discarding variable
-Cleanup locking to only take usb_lock around access to the control
endpoint, by no longer taking the lock around the bulk transfer
(which takes most of the time) we can remove the msleep(1) which was
needed to give the gspca core a chance to grab the usb_lock to signal
us to stop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds controls for vga cams with sensor type 0, in order to
correctly report the present controls, the probing of the sensor type
has been moved from sd_start to sd_config, since this made the sensor
type probing unreliable the detection method was changed.
Note this requires the camera to enter streaming mode, so sd_config now
briefly makes the camera stream.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as TeVii S460,S420.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch brings infrared remote support for some cx88 based cards.
Such as:
TeVii S460,S420; Omicom SS4; SatTrade ST4200;
TBS 8920,8910; Prof 7300,6200.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds an soc-camera / v4l2-subdev driver for the RJ54N1CB0C CMOS camera
sensor from Sharp. The sensor is very picky about initialisation and
configuration sequences. The driver limits artificially maximum window size by
800x600, although the sensor supports 1600x1200. Sizes above 800x600 don't seem
to work correctly, besides, examples from the system integrator use sizes above
640x480 only for still photography. Unfortunately, I had to use "magic"
register-value pairs for undocumented and "reserved" registers. This version of
the driver also omits some functionality, like cropping, which hasn't been
sufficiently tested yet and will be added later.
create mode 100644 drivers/media/video/rj54n1cb0c.c
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If CEU driver can not receive data from camera,
CETCR has VBP error state.
Then, CEU is stopped and cure operation is needed.
This patch add VBP error cure operation.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add comment about the meaning of the fixed JPEG header bytes used to
create each image.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The length check in reg_w_var() function is because the buffer contents
is copied to gspca_dev->usb_buf which has the size of USB_BUF_SZ bytes as
defined in drivers/media/video/gspca/gspca.h. Replace the number with
symbol for better readability and maintainability.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert tda18271_rf_tracking_filter_cal.rf_[ab][12] from int to s32.
Convert tda18271_priv.tm_rfcal from unsigned int to u8.
Cast subtractions between u32 values as s32.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use temporary variables for signed calulations between unsigned values
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
