The functions are the same as update_mqd().
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It may lose gpuvm invalidate acknowldege state across power-gating off
cycle. To avoid this issue in gmc9/gmc10 invalidation, add semaphore acquire
before invalidation and semaphore release after invalidation.
After adding semaphore acquire before invalidation, the semaphore
register become read-only if another process try to acquire semaphore.
Then it will not be able to release this semaphore. Then it may cause
deadlock problem. If this deadlock problem happens, it needs a semaphore
firmware fix.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SW must acquire/release one of the vm_invalidate_eng*_sem around the
invalidation req/ack. Through this way,it can avoid losing invalidate
acknowledge state across power-gating off cycle.
To use vm_invalidate_eng*_sem, it needs to initialize
vm_invalidate_eng*_sem firstly.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After rlcg fw 2.1, kmd driver starts to load extra fw for
LIST_CNTL,GPM_MEM,SRM_MEM. We needs to skip the three fw
because all rlcg related fw have been loaded by host driver.
Guest driver would load the three fw fail without this change.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Temporarily skip ras,dtm,hdcp initialize and terminate for arcturus VF
Currently the three features haven't been enabled at SRIOV, it would
trigger guest driver load fail with the bare-metal path of the three
features.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch fixes 2nd baco reset failure with gfxoff enabled on navi1x.
clear state buffer (resides in vram) is corrupted after 1st baco reset,
upon gfxoff exit, CPF gets garbage header in CSIB and hangs.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The pointer write_frame is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the standard _PR3 case, the pci core handles the pci state.
The driver only needs to handle it in the legacy ATPX case.
This may fix issues with runtime suspend/resume on certain
hybrid graphics laptops.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the mqd_diq_sdma buffer, there should be only one HIQ mqd. All DIQs
should be allocated somewhere else using the regular way.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is the same as KFD_MQD_TYPE_CP, so delete it. As a result, we will
have one less mqd mananger per device.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Get mmhub error counter by accessing EDC_CNT registers.
v2: Add mmhub_v9_4_ prefix for local static variable and function
Signed-off-by: Dennis Li <dennis.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add codes to print the detail EDC info for the subblock of mmhub
v2: Move the EDC_CNT registers' defintion from mmhub_9_4 header
files to mmhub_1_0 ones. Add mmhub_v1_0_ prefix for the local
static variable and function.
v3: squash in DC fix
Signed-off-by: Dennis Li <dennis.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The struct soc15_ras_field_entry will be reused by
other IPs, such as mmhub and gc
v2: rename ras_subblock_regs to gc_ras_fields_vg20,
because the future asic maybe have a different table.
Signed-off-by: Dennis Li <dennis.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
50us is not enough to wait for cp ready after gpu reset on some navi asics.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Suggested-by: Jack Xiao <Jack.Xiao@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only for the debugger use case.
[why]
Avoid endless translation retries, after an invalid address access has
been issued to the GPU. Instead, the trap handler is forced to enter by
generating a no-retry-fault.
A s_trap instruction is inserted in the debugger case to let the wave to
enter trap handler to save context.
[how]
Intentionally using an invalid flag combination (F and P set at the same
time) to trigger a no-retry-fault, after a retry-fault happens. This is
only valid under compute context.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Flag added to indicate if the amdgpu vm context is used for compute or
graphics.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
Everything is in place now. Not enabled by default yet. You
still have to specify runpm=1.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Originally we only supported runtime pm on PX/HG laptops
so vga_switcheroo and runtime pm are sort of entangled.
Attempt to logically separate them.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
BOCO - Bus Off, Chip Off
We originally only supported runtime pm on PX/HG
laptops so most of the runtime pm code looks for this.
Add a new flag to check for runtime pm enablement and
use this rather than checking for PX/HG.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
This adds the necessary support to the runtime suspend
and resume functions to handle boards that support
baco.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
Will be used for runtime pm. Entry will enter the BACO
state (chip off). Exit will exit the BACO state (chip on).
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
So we can use it for power savings rather than just reset.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
BOCO - Bus Off, Chip Off
We will take slightly different paths for boco and baco.
v2: fold together two consecutive if clauses
Reviewed-by: Evan Quan <evan.quan@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
BOCO - Bus Off, Chip Off
To better match what we are checking for and to align with
amdgpu_device_supports_baco.
BOCO is used on PowerXpress/Hybrid Graphics systems and BACO
is used on desktop dGPU boards.
v2: fix typo in documentation
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
To check if a device supports BACO or not. This will be
used in determining when to enable runtime pm.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
Check the BACO capabilities from the powerplay table.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
Check the BACO capabilities from the powerplay table.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
Check the BACO capabilities from the powerplay table.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
Check the BACO capabilities from the powerplay table.
v2: drop unrelated struct cleanup
Reviewed-by: Evan Quan <evan.quan@amd.com> (v1)
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BACO - Bus Active, Chip Off
Used to check whether the device supports BACO. This will
be used to enable runtime pm on devices which support BACO.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To get the value of gpu_busy_percent, it needs to realize
get_current_activity_percent and get_metrics_table.
The framework of renoir smu is different from old ones like raven. It
needs to realize get_current_activity_percent and get_metrics_table in
renoir_ppt.c like navi10.
v2: remove unused variable (Alex)
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ras_controller_irq and athub_err_event_irq are only registered
when PCIE_BIF ras is marked as supported. as the result, the driver
also just need pull the int status in such case.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop all the IP specific cmd_submit callback function
and use the common helper instead
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Except for ring wptr update, the psp ring cmd submission
function shouldn't be IP specific one. Create a common
helper function to be shared for all the ASICs.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The ring write pointer regsiter update is the only part that
is IP specific ones in psp_cmd_submit function.
Add two callbacks for wptr read/write so that we unify the
psp_cmd_submit function for all the ASICs.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This can fix the compile errors below:
drivers/gpu/drm/amd/amdgpu/../powerplay/smu_v11_0.c: In function ‘smu_v11_0_baco_set_state’:
drivers/gpu/drm/amd/amdgpu/../powerplay/smu_v11_0.c:1674:27: error: implicit declaration of function ‘amdgpu_ras_get_context’ [-Werror=implicit-function-declaration]
struct amdgpu_ras *ras = amdgpu_ras_get_context(adev);
^
drivers/gpu/drm/amd/amdgpu/../powerplay/smu_v11_0.c:1674:27: warning: initialization makes pointer from integer without a cast [-Wint-conversion]
drivers/gpu/drm/amd/amdgpu/../powerplay/smu_v11_0.c:1692:19: error: dereferencing pointer to incomplete type ‘struct amdgpu_ras’
if (!ras || !ras->supported) {
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable baco reset support on Arcturus.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Added bif doorbell interrupt setting and applied different
settings for BACO reset for RAS recovery.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1c42591591.
S/G display is not stable with the IOMMU enabled on some
platforms.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205523
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are still combinations of sbios and firmware that
are not stable.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=204689
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When gfxoff is enabled, accessing gfx registers via MMIO
can lead to a hang.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205497
Acked-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that the setting reflects what the hw supports. This will
be used in a subsequent patch so needs to be correct.
v2: squash in fix from Colin Ian King
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=205497
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
return errno code to caller when error occur, and meanwhile
remove gcc '-Wunused-but-set-variable' warning.
drivers/gpu/drm/amd/amdgpu/../powerplay/smumgr/vegam_smumgr.c: In function vegam_populate_smc_boot_level:
drivers/gpu/drm/amd/amdgpu/../powerplay/smumgr/vegam_smumgr.c:1364:6: warning: variable result set but not used [-Wunused-but-set-variable]
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/amdgpu/amdgpu_ih.c:64:13-31: WARNING: dma_alloc_coherent use in ih -> ring already zeroes out memory, so memset is not needed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The INTERRUPT_CNTL2 register expects a valid DMA address, but is
currently set with a GPU MC address. This can cause problems on
systems that detect the resulting DMA read from an invalid address
(found on a Power8 guest).
Instead, use the DMA address of the dummy page because it will always
be safe.
Fixes: 27ae10641e ("drm/amdgpu: add interupt handler implementation for si v3")
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
For MST connector atomic check we have to check a new CRTC state
instead of an old one, when checking if CRTC is disabled to
release VCPI slots allocated.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
static analysis throws the error below
Out-of-bounds read (OVERRUN)
Overrunning array of 5 bytes at byte offset 7 by dereferencing pointer
(uint64_t *)hdcp->auth.msg.hdcp1.bksv.
var n is going to contain r0p and bcaps. if they are non-zero the count
will be wrong
How]
Use memcpy instead to avoid this.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently we share rxstatus between HDMI and DP, so we use 16bits
The drm defines work with 1bytes at a time. So we need to
split the HDMI rxstatus into 2bytes before we can use drm defines
[How]
-create rxstatus for dp and hdmi. rxstatus for hdmi is split into bytes
using arrays.
-use drm_hdcp defines for the remaining structs
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
drm already has this define
[How]
drm Mask is 0x08 vs 0x0800. The reason is because drm mask
works on a byte. ^^
=======||
||
Since the first byte is always zero we can ignore it and only check the
second byte.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These defines/macros exist already no need to redefine them
[How]
Use the defines/macros from drm_hdcp.h
-we share the rxstatus between HDMI and DP (2 bytes), But upstream
defines/macros for HDMI are for 1 byte. So we need to create a separate
rxstatus for HDMI
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old way was to poll PSP and update the properties. But due to a
limitation in the PSP interface this doesn't work for MST.
[How]
According to PSP if set_encryption return success, the link is encrypted
and the only way it will not be is if we get a link loss(which we handle
already).
So this method should be good enough to report HDCP status.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Before we had a disable_type1 flag, this forced HDCP 2.2 to type0
There was no way to force type1.
[How]
Remove disable_type1 flag and instead add a flag to force type0/1.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to do this to support HDCP over MST
Currently we save a display per link, in a MST case we need to save
multiple displays per link.
[How]
We can create an array per link to cache the displays, but it
complicates the design. Instead we can use the module to cache the
displays.
Now we will always add all the displays to the module, but we use the
adjustment flag to disable hdcp on all of them before they are added.
When we want to enable hdcp we just query the display(cache), remove
it then add it back with different adjustments. Its the similar for
disable.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP 2.2 uses type0 and type1 content type. This is passed to the receiver
to stream the proper content.
For example, in a MST case if the main
device is HDCP2.2 capable but the secondary device is only 1.4 capabale
we can use Type0
Type0 content: use HDCP 1.4 or HDCP2.2 type0
Type1 content: Only use HDCP 2.2 type1
[How]
We use the "hdcp content type" property in drm. We use the
disable_type1 flag in hdcp module to select the type based on the
properties.
For updating the property we use the same logic as 1.4, but now we
consider content_type as well and update the property if the
requirements are met
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP 2.2 was disabled, we need to enable it
[How]
-Update display topology to support 2.2
-Unset hdcp2.disable in update_config
-Change logic of event_update_property, now we set the property to be
ENABLED for any level of encryption (2.2 or 1.4).
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP is a bit finicky so we try it 3 times, this leads to a case where
if we fail the first time and pass the second time the error is still
shown in dmesg for the first failed attempt.
This leads to false positive errors.
[How]
Change the logging from ERROR to WARNING. Warnings are still shown in dmesg
to know what went wrong.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to log the state changes for 2.2
This patch extends the existing logging functions to handle
HDCP2.2.
[How]
We do this by adding if/else in the defines, and output the log
based on the hdcp version
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The module works like a state machine
+-------------+
------> | Execution.c | ------
| +-------------+ |
| V
+----+ +--------+ +--------------+
| DM | -----> | Hdcp.c | <------------ | Transition.c |
+----+ <----- +--------+ +--------------+
This patch adds the execution and transition files for 2.2
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need these to read and write to aux/i2c, during
authentication
[How]
Create read/write functions for all the steps
(Eg, h_prime, paring_info etc)
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All the HDCP transactions should be verified using PSP
[How]
This patch adds the psp calls we need to verify the steps
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need some extra dmub_cmd_type for NV10
[How]
Add command table functions in DMUB firmware.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Xiong Yan <Xiong.Yan@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to be able to enable native 422 for debugging purposes.
[How]
Add new dc_debug_options bool and check it in the get_dsc_enc_caps
function.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When updating DSC config, a new config has to be validated before proceeding
with applying the update. Validation, however, modifies the current state.
This means DSC config validation would affect pipe re-assignment, causing
intermittent screen corruption issues when ODM is required for DSC.
[how]
- Use a copy of the current state for modified DSC config validation
- Set the update type to FULL_UPDATE to correctly validate and set the
actual state used for committing the streams
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN will hang if we access registers before PHY init is done.
So we need to spin or abort.
[How]
On hardware with DMCUB running and working we shouldn't time out
waiting for this to finish and we shouldn't hit the spin cycle.
If there's no hardware support then we should exit out of the function
early assuming that PHY init was already done elsewhere.
If we hit the timeout then there's likely a bug in firmware or software
and we need to debug - add errors and asserts as appropriate.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need validation that we are programming the expected values (rq, ttu, dlg)
from DML. This debug feature will output logs if we are programming
incorrect values and may help differentiate DAL issues from HW issues.
[How]
Dump relevant registers for each pipe with active stream. Compare current
reg values with the converted DML output. Log mismatches when found.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is becoming increasingly hard to figure out which
function is called on the different DCN versions
[How]
1. Make function pointer table init in its own init.c file
2. Remove other scenarios in hwseq.c file that need to
include headers of other DCN versions. (If needed,
it should have been done via the function pointers)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's an interface violation to use infinite loops within DMUB
service functions and we'll lock up the kernel by doing so.
[How]
Revert the function back to its intended functionality.
Move the infinite loops into DC/DM as necessary.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There can be a conflict between OS HDR multiplier and 3dlut HDR
multiplier, which are both sent to DC.
[HOW]
Instead of having dc determine which HDR multiplier to use, make the
decision in dm and send only the intended value in a surface update.
Store the current OS HDR multiplier and determine whether to use it or
the 3dlut's multiplier before sending the surface update to dc. Send
multiplier to dc in fixed31_32 format, dc then converts it to hw format.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
need to send immediate SDP message via debugfs on Navi board.
[how]
hook up the DCN1x encoder function of sending immediate sdp
message to DCN2.
Signed-off-by: David (Dingchen) Zhang <dingchen.zhang@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. Add trace code enum for easy debugging.
2. Add trace during uC boot up, including loading phy FW
and dmcu FW.
3. Change cache memory type back to write back,
since write through has issue when resume from S0i3 100% hang after
3.2ms.
4. Change CW3 base address to hard code value to avoid memory overlap
with cw1.
5. Change polling phy init done to infinite loop to avoid dcn hang when
dmcub uC stalled.
6. Add dmcub FW dis-assembly file to repositatory for debug purpose.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a case where the margin is between 50 and 60, but applying the
workaround causes a hang. By increasing the threshold, we are blocking more
cases from switching p-state during active, but those cases will fall back
to switching during blank, which is fine.
[How]
- increase required margin from 50 to 60
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the TEST_MSIC dpcd register field definition, the test equipment
has the option to choose between YCbCr601 or YCbCr709.
We will apply corresponding YCbCr coefficient based on this test
request.
[how]
Add a new input parameter in dc_link_dp_set_test_pattern to allow the
selection between different color space.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Too many construct functions which makes searching
difficult, especially on some debuggers.
[How]
Append all construct and destruct functions with dcn
number and object type to make each construct function
name unique
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous patch allowed to initialize debugfs entries on both MST
and SST connectors, but MST connectors get registered much later
which exposed an issue of debugfs entries being initialized in the
same folder.
[how]
Return SST debugfs entries' initialization back to where it was.
For MST connectors we should initialize debugfs entries in connector
register function after the connector is registered.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hanging on RV for DTN driver verifier
[How]
Roll back change and investigate further
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In SST mode no idle pattern will be generated after link training if
DIG FE is not connected to DIG BE.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We were missing debugfs files on MST connectors as the files
weren't initialized.
[how]
Move connector debugfs initialization into connoctor's
init helper function so it will be called by both SST and MST
connectors. Also move connector registration so it will be
registered before we create the entries.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
By default we shouldn't be trying to write secure registers during
DMUB hardware init.
[How]
Add a parameter to control whether we put the DMCUB into secure reset
and attempt to load CW0/CW1.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to avoid reprogramming the cache window when possible.
We don't need to worry about it for S3 but we *do* need to worry about
it for S4 resume.
DM can check whether hardware should be reinitialized or store software
state when going to S4 to know whether we need to reprogram hardware.
[How]
Add helpers to the DMUB service to check hardware initialization state.
DM will hook it up later.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes in dc to allow for different cases where full update is
required.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When sending DCC with Stereo, DCC gets enabled but the meta addresses
are 0. This happens momentarily before the meta addresses are populated
with a valid address.
[How]
Add call validate_dcc_with_meta_address() in
copy_surface_update_to_plane() to check for surface address and DCC
change.
When DCC has changed, check if DCC enable is true but meta address is 0.
If so, we turn DCC enable to false. When surface address has changed, we
check if DCC enable is false but meta address is not 0. If so, we turn
DCC enable back to true. This will restore DCC enable to the proper
setting once the meta address is valid.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDMI 2.0 HF-VSDB in EDID defines supported color depths in YCBCR420 modes.
But we did not honor these bit masks when choosing pixel encoding.
HDMI 2.0 compliance tests with deep color and YCBCR420 failed as a result.
[How]
Cap color depth based on y420_dc_modes from EDID.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Background color only takes effect in bottommost mpcc.
[How]
Update background color in bottommost mpcc.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debug purpose, we need to check HUBP_CLOCK_ENABLE in DTN
log debugfs on Navi.
[How]
Add related register read in dcn20_hubp.c.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before we were reading registers specific to luma size, which caused a black line
to appear on the screen from time to time, as although the luma row height
is generally the same as the chroma row height for the video case, it will sometimes
be one more
[how]
Read the register specific for the chroma size
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
we want to increase the pte row plus 1 line if chroma viewport
height is integer multiple of the pte row height
[how]
instead of ceiling viewport height, we floor it. this allows
us to accommodate both cases: those where the chroma viewport
height is integer multiple of the pte row height and those where
it is not
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An old display with no audio may not have an EDID with a CEA block, or
it may simply be too old to support audio. This is not a driver error,
so don't flag it as such.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112140
References: ae2a349597 ("drm/amd: be quiet when no SAD block is found")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/modules/color/color_gamma.c: In function build_freesync_hdr:
drivers/gpu/drm/amd/display/modules/color/color_gamma.c:830:20: warning: variable min_content set but not used [-Wunused-but-set-variable]
It is not used since commit 50575eb5b3 ("drm/amd/display:
Only use EETF when maxCL > max display")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/bios/bios_parser.c: In function bios_get_board_layout_info:
drivers/gpu/drm/amd/display/dc/bios/bios_parser.c:2743:22: warning: variable bp set but not used [-Wunused-but-set-variable]
It is introduced by commit 1eeedbcc20 ("drm/amd/display:
get board layout for edid emulation"), but never used,
so remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c: In function bios_get_board_layout_info:
drivers/gpu/drm/amd/display/dc/bios/bios_parser2.c:1826:22: warning: variable bp set but not used [-Wunused-but-set-variable]
It is introduced by commit 1eeedbcc20 ("drm/amd/display:
get board layout for edid emulation"), but never used,
so remove it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
