Calls to tasklet_hi_enable are replaced by calls to
tasklet_enable since the 2 functions are redundant.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is present on older revisions of the DE2 development kit.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is present on the Nios2 Development Kit 2C35.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware 1.12.25.0 added support for QSA module, adding the driver code for it.
Also fixes some ethtool get settings for other module types.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programs the firmware of the maximum outgoing iscsi pdu length per connection.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building the bcmgenet driver as module, I get:
ERROR: "fixed_phy_register" [drivers/net/ethernet/broadcom/genet/genet.ko] undefined!
commit b0ba512e225d72 ("net: bcmgenet: enable driver to work without device
tree") which added a call to fixed_phy_register. But fixed_phy_register
needs to be exported if used from a module.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both sunvdc and sunvnet implemented distinct functionality for incrementing
and decrementing dring indexes. Create common functions for use by both
from the sunvnet versions, which were chosen since they will still work
correctly in case a non power of two ring size is used.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ephy parameter to rtl8168g.
Also change the common function of rtl8168g from "rtl_hw_start_8168g_1" to
"rtl_hw_start_8168g". And function "rtl_hw_start_8168g_1" is used for
setting rtl8168g hardware parameters.
Following is the explanation of what hardware parameter change for.
rtl8168g may erroneous judge the PCIe signal quality and show the error bit
on PCI configuration space when in PCIe low power mode.
The following ephy parameters are for above issue.
{ 0x00, 0x0000, 0x0008 }
{ 0x0c, 0x37d0, 0x0820 }
{ 0x1e, 0x0000, 0x0001 }
rtl8168g may return to PCIe L0 from PCIe L0s low power mode too slow.
The following ephy parameter is for above issue.
{ 0x19, 0x8000, 0x0000 }
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ports of the switch that we define as "fixed PHYs" such as MoCA, we
would have our Port 7 special handling that would allow us to assert the
link status indication.
For other ports, such as e.g: RGMII_1 connected to a cable modem, we
would rely on whatever the bootloader has left configured, which is a
bad assumption to make, we really need to force the link status
indication here.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that dma_rmb is used when reading the Rx
descriptor. The advantage of dma_rmb is that it allows for a much
lower cost barrier on x86, powerpc, arm, and arm64 architectures than a
traditional memory barrier when dealing with reads that only have to
synchronize to coherent memory.
In addition I have updated the code so that it just checks to see if any
bits have been set instead of just the DD bit since the DD bit will always
be set as a part of a descriptor write-back so we just need to check for a
non-zero value being present at that memory location rather than just
checking for any specific bit. This allows the code itself to appear much
cleaner and allows the compiler more room to optimize.
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8169 use a pair of wmb() calls when setting up the descriptor rings.
The first is to synchronize the descriptor data with the descriptor status,
and the second is to synchronize the descriptor status with the use of the
MMIO doorbell to notify the device that descriptors are ready. This can
come at a heavy price on some systems, and is not really necessary on
systems such as x86 as a simple barrier() would suffice to order store/store
accesses. As such we can replace the first memory barrier with
dma_wmb() to reduce the cost for these accesses.
In addition the r8169 uses a rmb() to prevent compiler optimization in the
cleanup paths, however by moving the barrier down a few lines and replacing
it with a dma_rmb() we should be able to use it to guarantee
descriptor accesses do not occur until the device has updated the DescOwn
bit from its end.
One last change I made is to move the update of cur_tx in the xmit path to
after the wmb. This way we can guarantee the device and all CPUs should
see the DescOwn update before they see the cur_tx value update.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
"This is an unusually large pull request for MIPS - in parts because
lots of patches missed the 3.18 deadline but primarily because some
folks opened the flood gates.
- Retire the MIPS-specific phys_t with the generic phys_addr_t.
- Improvments for the backtrace code used by oprofile.
- Better backtraces on SMP systems.
- Cleanups for the Octeon platform code.
- Cleanups and fixes for the Loongson platform code.
- Cleanups and fixes to the firmware library.
- Switch ATH79 platform to use the firmware library.
- Grand overhault to the SEAD3 and Malta interrupt code.
- Move the GIC interrupt code to drivers/irqchip
- Lots of GIC cleanups and updates to the GIC code to use modern IRQ
infrastructures and features of the kernel.
- OF documentation updates for the GIC bindings
- Move GIC clocksource driver to drivers/clocksource
- Merge GIC clocksource driver with clockevent driver.
- Further updates to bring the GIC clocksource driver up to date.
- R3000 TLB code cleanups
- Improvments to the Loongson 3 platform code.
- Convert pr_warning to pr_warn.
- Merge a bunch of small lantiq and ralink fixes that have been
staged/lingering inside the openwrt tree for a while.
- Update archhelp for IP22/IP32
- Fix a number of issues for Loongson 1B.
- New clocksource and clockevent driver for Loongson 1B.
- Further work on clk handling for Loongson 1B.
- Platform work for Broadcom BMIPS.
- Error handling cleanups for TurboChannel.
- Fixes and optimization to the microMIPS support.
- Option to disable the FTLB.
- Dump more relevant information on machine check exception
- Change binfmt to allow arch to examine PT_*PROC headers
- Support for new style FPU register model in O32
- VDSO randomization.
- BCM47xx cleanups
- BCM47xx reimplement the way the kernel accesses NVRAM information.
- Random cleanups
- Add support for ATH25 platforms
- Remove pointless locking code in some PCI platforms.
- Some improvments to EVA support
- Minor Alchemy cleanup"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (185 commits)
MIPS: Add MFHC0 and MTHC0 instructions to uasm.
MIPS: Cosmetic cleanups of page table headers.
MIPS: Add CP0 macros for extended EntryLo registers
MIPS: Remove now unused definition of phys_t.
MIPS: Replace use of phys_t with phys_addr_t.
MIPS: Replace MIPS-specific 64BIT_PHYS_ADDR with generic PHYS_ADDR_T_64BIT
PCMCIA: Alchemy Don't select 64BIT_PHYS_ADDR in Kconfig.
MIPS: lib: memset: Clean up some MIPS{EL,EB} ifdefery
MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO
MIPS: <asm/types.h> fix indentation.
MAINTAINERS: Add entry for BMIPS multiplatform kernel
MIPS: Enable VDSO randomization
MIPS: Remove a temporary hack for debugging cache flushes in SMTC configuration
MIPS: Remove declaration of obsolete arch_init_clk_ops()
MIPS: atomic.h: Reformat to fit in 79 columns
MIPS: Apply `.insn' to fixup labels throughout
MIPS: Fix microMIPS LL/SC immediate offsets
MIPS: Kconfig: Only allow 32-bit microMIPS builds
MIPS: signal.c: Fix an invalid cast in ISA mode bit handling
MIPS: mm: Only build one microassembler that is suitable
...
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
This adds a lot of infrastructure for virtio 1.0 support.
Notable missing pieces: virtio pci, virtio balloon (needs spec extension),
vhost scsi.
Plus, there are some minor fixes in a couple of places.
Cc: David Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUh1CVAAoJECgfDbjSjVRpWZcH/2+EGPyng7Lca820UHA0cU1U
u4D8CAAwOGaVdnUUo8ox1eon3LNB2UgRtgsl3rBDR3YTgFfNPrfuYdnHO0dYIDc1
lS26NuPrVrTX0lA+OBPe2nlKrsrOkn8aw1kxG9Y0gKtNg/+HAGNW5e2eE7R/LrA5
94XbWZ8g9Yf4GPG1iFmih9vQvvN0E68zcUlojfCnllySgaIEYr8nTiGQBWpRgJat
fCqFAp1HMDZzGJQO+m1/Vw0OftTRVybyfai59e6uUTa8x1djvzPb/1MvREqQjegM
ylSuofIVyj7JPu++FbAjd9mikkb53GSc8ql3YmWNZLdr69rnkzP0GdzQvrdheAo=
=RtrR
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio: virtio 1.0 support, misc patches
This adds a lot of infrastructure for virtio 1.0 support. Notable
missing pieces: virtio pci, virtio balloon (needs spec extension),
vhost scsi.
Plus, there are some minor fixes in a couple of places.
Note: some net drivers are affected by these patches. David said he's
fine with merging these patches through my tree.
Rusty's on vacation, he acked using my tree for these, too"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (70 commits)
virtio_ccw: finalize_features error handling
virtio_ccw: future-proof finalize_features
virtio_pci: rename virtio_pci -> virtio_pci_common
virtio_pci: update file descriptions and copyright
virtio_pci: split out legacy device support
virtio_pci: setup config vector indirectly
virtio_pci: setup vqs indirectly
virtio_pci: delete vqs indirectly
virtio_pci: use priv for vq notification
virtio_pci: free up vq->priv
virtio_pci: fix coding style for structs
virtio_pci: add isr field
virtio: drop legacy_only driver flag
virtio_balloon: drop legacy_only driver flag
virtio_ccw: rev 1 devices set VIRTIO_F_VERSION_1
virtio: allow finalize_features to fail
virtio_ccw: legacy: don't negotiate rev 1/features
virtio: add API to detect legacy devices
virtio_console: fix sparse warnings
vhost: remove unnecessary forward declarations in vhost.h
...
Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.
But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):
CPU 1 CPU 2
deferred work vxlan_sock_add
... ...
spin_lock(&vn->sock_lock)
vs = vxlan_find_sock();
vxlan_sock_release
dec vs->refcnt, reaches 0
spin_lock(&vn->sock_lock)
vxlan_sock_hold(vs), refcnt=1
spin_unlock(&vn->sock_lock)
hlist_del_rcu(&vs->hlist);
vxlan_notify_del_rx_port(vs)
spin_unlock(&vn->sock_lock)
So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 7c47cedf43 ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the required firmware commands for A0 steering and a way to enable
that. The firmware support focuses on INIT_HCA, QUERY_HCA, QUERY_PORT,
QUERY_DEV_CAP and QUERY_FUNC_CAP commands. Those commands are used
to configure and query the device.
The different A0 DMFS (steering) modes are:
Static - optimized performance, but flow steering rules are
limited. This mode should be choosed explicitly by the user
in order to be used.
Dynamic - this mode should be explicitly choosed by the user.
In this mode, the FW works in optimized steering mode as long as
it can and afterwards automatically drops to classic (full) DMFS.
Disable - this mode should be explicitly choosed by the user.
The user instructs the system not to use optimized steering, even if
the FW supports Dynamic A0 DMFS (and thus will be able to use optimized
steering in Default A0 DMFS mode).
Default - this mode is implicitly choosed. In this mode, if the FW
supports Dynamic A0 DMFS, it'll work in this mode. Otherwise, it'll
work at Disable A0 DMFS mode.
Under SRIOV configuration, when the A0 steering mode is enabled,
older guest VF drivers who aren't using the RX QP allocation flag
(MLX4_RESERVE_A0_QP) will get a QP from the general range and
fail when attempting to register a steering rule. To avoid that,
the PF context behaviour is changed once on A0 static mode, to
require support for the allocation flag in VF drivers too.
In order to enable A0 steering, we use log_num_mgm_entry_size param.
If the value of the parameter is not positive, we treat the absolute
value of log_num_mgm_entry_size as a bit field. Setting bit 2 of this
bit field enables static A0 steering.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently QUERY_PORT is done as a part of QUERY_DEV_CAP firmware command.
Since we would like to use it without querying all device capabilities,
extract this part to be a function of its own.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a given flow steering rule is invalid in respect to the current
steering configuration, print the correct error message to the system log.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zone allocator is a mechanism which manages a few mlx4_bitmaps.
When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of reserved QPs is affected both from the firmware and
from the driver's requirements. This patch adds a check that
validates that this number is indeed feasable.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs (guests in this context) issue the QUERY_DEV_CAP command, they
need not be told that host side virtualization features such as VST, FSM
(MAC anti-spoofing) and running > 80 VFs are supported by the device.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was dropped by mistake for the napi_gro_frags flow, fix that.
Fixes: dd65beac48 ('net/mlx4_en: Extend usage of napi_gro_frags')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The encapsulated offload flags shouldn't be unconditionally exported
to the stack. The stack expects offloading to work across all tunnel
types when those flags are set. This would break other tunnels (like
GRE) since be2net currently supports tunnel offload for VxLAN only.
Also, with VxLANs Skyhawk-R can offload only 1 UDP dport. If more
than 1 UDP port is added, we should disable offloads in that case too.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use dma_mapping_error() to check the dma address returned
by dma_map_single/page(). Otherwise we would get warning like this:
WARNING: at lib/dma-debug.c:1140
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-rc2-next-20141029 #196
task: c0834300 ti: effe6000 task.ti: c0874000
NIP: c02b2c98 LR: c02b2c98 CTR: c030abc4
REGS: effe7d70 TRAP: 0700 Not tainted (3.18.0-rc2-next-20141029)
MSR: 00021000 <CE,ME> CR: 22044022 XER: 20000000
GPR00: c02b2c98 effe7e20 c0834300 00000098 00021000 00000000 c030b898 00000003
GPR08: 00000001 00000000 00000001 749eec9d 22044022 1001abe0 00000020 ef278678
GPR16: ef278670 ef278668 ef278660 070a8040 c087f99c c08cdc60 00029000 c0840d44
GPR24: c08be6e8 c0840000 effe7e78 ef041340 00000600 ef114e10 00000000 c08be6e0
NIP [c02b2c98] check_unmap+0x51c/0x9e4
LR [c02b2c98] check_unmap+0x51c/0x9e4
Call Trace:
[effe7e20] [c02b2c98] check_unmap+0x51c/0x9e4 (unreliable)
[effe7e70] [c02b31d8] debug_dma_unmap_page+0x78/0x8c
[effe7ed0] [c03d1640] gfar_clean_rx_ring+0x208/0x488
[effe7f40] [c03d1a9c] gfar_poll_rx_sq+0x3c/0xa8
[effe7f60] [c04f8714] net_rx_action+0xc0/0x178
[effe7f90] [c00435a0] __do_softirq+0x100/0x1fc
[effe7fe0] [c0043958] irq_exit+0xa4/0xc8
[effe7ff0] [c000d14c] call_do_irq+0x24/0x3c
[c0875e90] [c00048a0] do_IRQ+0x8c/0xf8
[c0875eb0] [c000ed10] ret_from_except+0x0/0x18
For TX, we need to unmap the pages which has already been mapped and
free the skb before return.
For RX, move the dma mapping and error check to gfar_new_skb(). We
would reuse the original skb in the rx ring when either allocating
skb failure or dma mapping error.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove use of calls into t4_fw_hello() with MASTER_MUST, which results in
FW_HELLO_CMD_MASTERFORCE being set. The firmware doesn't support this and of
course any existing PF Drivers will totally go for a toss.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Before phy device link up, we only enable FEC mdio interrupt, which
is more reasonable.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For i.MX6SX FEC controller, there have interrupt mask and event
field extension. To support all SOCs FEC, we clear all interrupt
events during MAVC initial process.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some i.MX6 serial boards, phy power and refrence clock are supplied
or controlled by SOC. When do suspend/resume test, the power and clock
are disabled, so phy device link down.
For current driver, fep->link is still up status, which cause extra operation
like below code. To avoid the dumy operation, we set fep->link to down when
phy device is real down.
...
if (fep->link) {
napi_disable(&fep->napi);
netif_tx_lock_bh(ndev);
fec_stop(ndev);
netif_tx_unlock_bh(ndev);
napi_enable(&fep->napi);
fep->link = phy_dev->link;
status_change = 1;
}
...
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull VFS changes from Al Viro:
"First pile out of several (there _definitely_ will be more). Stuff in
this one:
- unification of d_splice_alias()/d_materialize_unique()
- iov_iter rewrite
- killing a bunch of ->f_path.dentry users (and f_dentry macro).
Getting that completed will make life much simpler for
unionmount/overlayfs, since then we'll be able to limit the places
sensitive to file _dentry_ to reasonably few. Which allows to have
file_inode(file) pointing to inode in a covered layer, with dentry
pointing to (negative) dentry in union one.
Still not complete, but much closer now.
- crapectomy in lustre (dead code removal, mostly)
- "let's make seq_printf return nothing" preparations
- assorted cleanups and fixes
There _definitely_ will be more piles"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
copy_from_iter_nocache()
new helper: iov_iter_kvec()
csum_and_copy_..._iter()
iov_iter.c: handle ITER_KVEC directly
iov_iter.c: convert copy_to_iter() to iterate_and_advance
iov_iter.c: convert copy_from_iter() to iterate_and_advance
iov_iter.c: get rid of bvec_copy_page_{to,from}_iter()
iov_iter.c: convert iov_iter_zero() to iterate_and_advance
iov_iter.c: convert iov_iter_get_pages_alloc() to iterate_all_kinds
iov_iter.c: convert iov_iter_get_pages() to iterate_all_kinds
iov_iter.c: convert iov_iter_npages() to iterate_all_kinds
iov_iter.c: iterate_and_advance
iov_iter.c: macros for iterating over iov_iter
kill f_dentry macro
dcache: fix kmemcheck warning in switch_names
new helper: audit_file()
nfsd_vfs_write(): use file_inode()
ncpfs: use file_inode()
kill f_dentry uses
lockd: get rid of ->f_path.dentry->d_sb
...
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting/getting rss hash key using ethtool.
v2:
respin patch to support RSS hash function changes.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the calls to netdev_alloc_skb_ip_align in the
copybreak paths.
Cc: Gary Zambrano <zambrano@broadcom.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces most of the calls to netdev_alloc_skb_ip_align in the Realtek
drivers. The one instance I didn't replace in 8139cp.c is because it was
called as a part of init and as such is not always accessed from the
softirq context.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use napi_alloc_skb I needed to pass a pointer to struct adapter
instead of struct pci_dev. This allowed me to access &adapter->napi.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change replaces calls to netdev_alloc_skb_ip_align with
napi_alloc_skb. The advantage of napi_alloc_skb is currently the fact that
the page allocation doesn't make use of any irq disable calls.
There are few spots where I couldn't replace the calls as the buffer
allocation routine is called as a part of init which is outside of the
softirq context.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use MODULE_VERSION() now that dummy driver has a version.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The disable_irq_nosync function, not the disable_irq function, must be
used to disable the DMA channel interrupt from within the interrupt
service routine. Change the disable_irq call to disable_irq_nosync.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 97a6d1bb2b (xen-netfront: Fix
handling packets on compound pages with skb_linearize) attempted to
fix a problem where an skb that would have required too many slots
would be dropped causing TCP connections to stall.
However, it filled in the first slot using the original buffer and not
the new one and would use the wrong offset and grant access to the
wrong page.
Netback would notice the malformed request and stop all traffic on the
VIF, reporting:
vif vif-3-0 vif3.0: txreq.offset: 85e, size: 4002, end: 6144
vif vif-3-0 vif3.0: fatal error; disabling device
Reported-by: Anthony Wright <anthony@overnetdata.com>
Tested-by: Anthony Wright <anthony@overnetdata.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When xenvif_alloc() fails, it returns a non-NULL error indicator. To
avoid eventual races, we shouldn't store that into struct backend_info
as readers of it only check for NULL.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook a ndo_set_mac_address callback, update the internal Ethernet MAC in
the netdevice structure, and finally write that address down to the
UniMAC registers. If the interface is down, and most likely clock gated,
we do not update the registers but just the local copy, such that next
ndo_open() call will effectively write down the address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove use of 'swdev' mode in rocker. rocker dev offloads
can use the BRIDGE_FLAGS_SELF to indicate offload to hardware.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-12-08
Please pull this last batch of pending wireless updates for the 3.19 tree...
For the wireless bits, Johannes says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
For the Bluetooth bits, Johan says:
"Here's one more bluetooth-next pull request for 3.19:
- Minor cleanups for ieee802154 & mac802154
- Fix for the kernel warning with !TASK_RUNNING reported by Kirill A.
Shutemov
- Support for another ath3k device
- Fix for tracking link key based security level
- Device tree bindings for btmrvl + a state update fix
- Fix for wrong ACL flags on LE links"
And...
"In addition to the previous one this contains two more cleanups to
mac802154 as well as support for some new HCI features from the
Bluetooth 4.2 specification.
From the original request:
'Here's what should be the last bluetooth-next pull request for 3.19.
It's rather large but the majority of it is the Low Energy Secure
Connections feature that's part of the Bluetooth 4.2 specification. The
specification went public only this week so we couldn't publish the
corresponding code before that. The code itself can nevertheless be
considered fairly mature as it's been in development for over 6 months
and gone through several interoperability test events.
Besides LE SC the pull request contains an important fix for command
complete events for mgmt sockets which also fixes some leaks of hci_conn
objects when powering off or unplugging Bluetooth adapters.
A smaller feature that's part of the pull request is service discovery
support. This is like normal device discovery except that devices not
matching specific UUIDs or strong enough RSSI are filtered out.
Other changes that the pull request contains are firmware dump support
to the btmrvl driver, firmware download support for Broadcom BCM20702A0
variants, as well as some coding style cleanups in 6lowpan &
ieee802154/mac802154 code.'"
For the NFC bits, Samuel says:
"With this one we get:
- NFC digital improvements for DEP support: Chaining, NACK and ATN
support added.
- NCI improvements: Support for p2p target, SE IO operand addition,
SE operands extensions to support proprietary implementations, and
a few fixes.
- NFC HCI improvements: OPEN_PIPE and NOTIFY_ALL_CLEARED support,
and SE IO operand addition.
- A bunch of minor improvements and fixes for STMicro st21nfcb and
st21nfca"
For the iwlwifi bits, Emmanuel says:
"Major works are CSA and TDLS. On top of that I have a new
firmware API for scan and a few rate control improvements.
Johannes find a few tricks to improve our CPU utilization
and adds support for a new spin of 7265 called 7265D.
Along with this a few random things that don't stand out."
And...
"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
a infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
For the Atheros bits, Kalle says:
"Only ath10k changes this time and no major changes. Most visible are:
o new debugfs interface for runtime firmware debugging (Yanbo)
o fix shared WEP (Sujith)
o don't rebuild whenever kernel version changes (Johannes)
o lots of refactoring to make it easier to add new hw support (Michal)
There's also smaller fixes and improvements with no point of listing
here."
In addition, there are a few last minute updates to ath5k,
ath9k, brcmfmac, brcmsmac, mwifiex, rt2x00, rtlwifi, and wil6210.
Also included is a pull of the wireless tree to pick-up the fixes
originally included in "pull request: wireless 2014-12-03"...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PTR_ALIGN macro after skb_reserve is redundant, because skb_reserve
function adjusts the alignment of skb->data.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of 'boguscnt' and 'quota' have nearly meaning as the condition of
the reception loop.
In order to cut down redundant processing, this patch changes excess
judgement.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-12-09
This series contains updates to i40e and i40evf.
Jeff (me) provides a single patch to convert a macro to a static inline
function based on feedback from Joe Perches on a previous patch.
Shannon provides the remaining twelve patches against i40e. Almost all
of Shannon's patches cleanup/fix NVM issues varying in range from
adding more detail to debug messages, to removing dead code, to fixing
NVM state transitions after an error. Change the handy decoder interface
for admin queue return code to help catch and properly report the condition
as a useful errno rather than returning a misleading '0'. Added a range
check to avoid any possible array index-out-of-bound issues.
v2:
- fixed up patch 05 in the series to use the ARRAY_SIZE() macro as suggested
by Sergei Shtylyov
- fix up patch 13 to remove unnecessary parens in the return statement
as suggested by Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=icE1
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.19-20141207' of git://gitorious.org/linux-can/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2014-12-07
this is a pull request of 8 patches for net-next/master.
Andri Yngvason contributes 4 patches in which the CAN state change
handling is consolidated and unified among the sja1000, mscan and
flexcan driver. The three patches by Jeremiah Mahler fix spelling
mistakes and eliminate the banner[] variable in various parts. And a
patch by me that switches on sparse endianess checking by default.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4HML
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.18-20141207' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-12-07
this is a pull request of three patches by Stephane Grosjean which fix several
bugs in the peak_usb CAN drivers.
Please queue, if possible for 3.18, if it's too late these patches takes the
slow lane via net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that the code _using_ ->msg_iter at that point will be very
unhappy with anything other than unshifted iovec-backed iov_iter.
We still need to convert users to proper primitives.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a misspelled function name by %s and then __func__.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function name contains cleanup, not clean.
This was done using Coccinelle, including the use of Levenshtein distance,
as proposed by Rasmus Villemoes.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device is already used as an ipvlan port then refuse to
use it as a macvlan port at early stage of port creation.
thost1:~# ip link add link eth0 ipvl0 type ipvlan
thost1:~# echo $?
0
thost1:~# ip link add link eth0 mvl0 type macvlan
RTNETLINK answers: Device or resource busy
thost1:~# echo $?
2
thost1:~#
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the port check [ipvlan_dev_master()] and device check
[ipvlan_dev_slave()] functions to netdevice.h and rename them
netif_is_ipvlan_port() and netif_is_ipvlan() resp. to be
consistent with macvlan api naming.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device is already a macvlan port then refuse to use it as
an ipvlan port in the early stage of port creation.
thost1:~# ip link add link eth0 mvl0 type macvlan
thost1:~# echo $?
0
thost1:~# ip link add link eth0 ipvl0 type ipvlan
RTNETLINK answers: Device or resource busy
thost1:~# echo $?
2
thost1:~#
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The command 'ethtool -i' is useful to find details
about the interface like the device driver being used.
This was missing for dummy driver.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit fbe168ba91 ("net: generic dev_disable_lro() stacked
device handling"), dev_disable_lro() zeroes NETIF_F_LRO feature flag
first for a macvlan device and then for its lower device. As an attempt
to set NETIF_F_LRO to zero is ignored, dev_disable_lro() issues a
warning and taints kernel.
Allowing NETIF_F_LRO to be set independently of the lower device
consists of three parts:
- add the flag to hw_features to allow toggling it
- allow setting it to 0 even if lower device has the flag set
- add the flag to MACVLAN_FEATURES to restore copying from lower
device on macvlan creation
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline functions are preferred over macros when they can be used
interchangeably.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a little more state context to an NVM update debug message.
Change-ID: I512160259052bcdbe5bdf1adf403ab2bf7984970
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Decoding the AQ return code is great except when the AQ send timed out
and there's no return code set. This changes the handy decoder
interface to help catch and properly report the condition as a useful
errno rather than returning a misleading '0'.
Change-ID: I07a1f94f921606da49ffac7837bcdc37cd8222eb
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Only poll on the NVM semaphore if there's time left on a previous
reservation. Also, add a little more info to debug messages.
Change-ID: I2439bf870b95a28b810dcb5cca1c06440463cf8a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The state transitions after an error were not managed well, so
these changes get us back to the INIT state or don't transition
out of the INIT state after most errors.
Change-ID: I90aa0e4e348dc4f58cbcdce9c5d4b7fd35981c6c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't bother trying to set a smaller timeout on the polling,
just simplify the code and always use the max limit. Also,
rename a variable for clarity and fix a comment.
Change-ID: I0300c3562ccc4fd5fa3088f8ae52db0c1eb33af5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The nvm_semaphore_wait field is set but never used, so let's
just get rid of it.
Change-ID: I2107bd29b69f99b1a61d7591d087429527c9d8fa
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The adminq init is run after the EMPR that is triggered by the
NVM update. The final write command will cause the reset and
will want to wait for the ARQ event that signals the end of the
update, but the reset precludes the event being sent. The state
is probably already at INIT, but we set it so here anyway, and
clear the release_on_done flag as well.
Change-ID: Ie9d724a39e71f988741abc3d51b4cb198c7e0272
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Acked-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just to be sure, add a range check to avoid any possible
array index-out-of-bound issues.
CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Change-ID: I9323bee6732c2a47599816e1d6c6b3a1f8dcbf54
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Michal Kosiarz <michal.kosiarz@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rework the debug messages in the NVM update state machine so that we can
turn them on and off dynamically rather than forcing a recompile/reload.
These can now be turned on with something like:
ethtool -s eth1 msglvl 0xf000008f
and off with:
ethtool -s eth1 msglvl 0xf000000f
The high 0xf0000000 gets the driver's attention that we want to change the
internal debug flags, and the 0x80 bit is the NVM debug.
Change-ID: I5efb9039400304b29a0fd6ddea3f47bb362e6661
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM update operations take time finish asynchronously, and follow-on
update requests need to wait for the current one to finish. Early
firmware didn't handle this well, so the code had to track the busy state.
The released firmware handles the busy state correctly, returning
I40E_AQ_RC_EBUSY if an update is still in progress, so the code no longer
needs to track this.
Change-ID: I6e6b4adc26d6dcc5fd7adfee5763423858a7d921
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add more detail to the NVM update error messages so folks
have a better chance at diagnosing issues without having to
resort to heroic measures to reproduce an issue.
Change-ID: I270d1a9c903baceaef0bebcc55d29108ac08b0bd
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Once in a great while the NVMUpdate tools and the driver get out
of phase with each other. This gives us a way to reset things
without having to unload the driver.
Change-ID: I353f688236249a666a90ba3e7233e0ed8c1a04e9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Kconfig file says that Gigabit mode is not supported, but it has been
supported since commit 140b7552fd ("net/macb:
Add support for Gigabit Ethernet mode").
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a configuration with CONFIG_BRIDGE set to 'm' and CONFIG_ROCKER
set to 'y', undefined references occur at link time:
> drivers/built-in.o: In function `rocker_port_fdb_learn_work':
> /home/jim/linux/drivers/net/ethernet/rocker/rocker.c:3014: undefined
> reference to `br_fdb_external_learn_del'
> /home/jim/linux/drivers/net/ethernet/rocker/rocker.c:3016: undefined
> reference to `br_fdb_external_learn_add'
This patch fixes these by declaring CONFIG_ROCKER as being dependent
on CONFIG_BRIDGE.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing Tx cleanup, the dirty index counter is compared to the
current index counter as one of the tests used to determine when to stop
cleanup. The "less than" test will fail when the current index counter
rolls over to zero causing cleanup to never occur again. Update the test
to a "not equal" to avoid this situation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our FW can support several fastpath HSI [for backward compatibility] but up
until now VFs were always configured to use latest fastpath HSI [although VF
driver might be older and use an older fastpath HSI].
For linux drivers, the differences are insignificant since driver never
utilized features that were overridden by the HSI change. But for VMs running
other operating systems this might be a problem.
In addition, eventually FW might change fastpath HSI in such a manner that
backward compatibility WILL break unless configured with proper version.
This patch fixes the issue for other operating system VMs, as well as lays
the ground work for forward compatibility in regard to the fastpath HSI.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment says that the built-in strncmp didn't work. That is not
surprising, as apparently "str" semantics are not really what is
wanted (hint: de4x5_strncmp only stops when two different bytes are
encountered or the end is reached; not if either byte happens to be
0). de4x5_strncmp is actually a memcmp (except for the signature and
that bytes are not necessarily treated as unsigned char); since only
the boolean value of the result is used we can just replace
de4x5_strncmp with memcmp.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW is present in AM33xx, AM43xx, DRA7xx.
Updating the Kconfig to depend on ARCH_OMAP2PLUS instead of listing
all SoC's.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefine REALTEK_USB_DEVICE for the desired USB interface for probe().
There are three USB interfaces for the device. USB_CLASS_COMM and
USB_CLASS_CDC_DATA are for ECM mode (config #2). USB_CLASS_VENDOR_SPEC
is for the vendor mode (config #1). However, we are not interesting
in USB_CLASS_CDC_DATA for probe(), so redefine REALTEK_USB_DEVICE
to ignore the USB interface class of USB_CLASS_CDC_DATA.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-12-03
One last(?) batch of fixes hoping to make 3.18...
In this episode, we have another trio of rtlwifi fixes
repairing a little more damage from the major update of the
rtlwifi-family of drivers. These editing mistakes caused some
memory corruption and missed a flag critical to proper interrupt
handling. Together, these fix the kernel regression reported at
https://bugzilla.kernel.org/show_bug.cgi?id=88951 by Catalin Iacob.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After successfully loading new firmware, reload the new firmware's version
number information so "ethtool -i", etc. will report the right value
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BAR2 Going To Sleep (GTS) for T5 and later. Use new BAR2 User Doorbells for
T5 for both cxgb4 and cxgb4vf driver.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new Common Code facilities for calculating T5 BAR2 Offsets for SGE Queue
Registers. This new code can handle situations where
Queues Per Page * SGE BAR2 Queue Register Area Size > Page Size
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sge_vf_eq_qpp and sge_vf_iq_qpp to (struct sge_params), initialize
sge_queues_per_page and sge_vf_qpp in t4vf_get_sge_params(), add new
t4vf_prep_adapter() which initializes basic adapter parameters.
Grab both SGE_EGRESS_QUEUES_PER_PAGE_VF and SGE_INGRESS_QUEUES_PER_PAGE_VF
for VF Drivers since we need both to calculate the User Doorbell area
offsets for Egress and Ingress Queues.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This kills the sparse warnings.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 1G-SFP module detection by verifying not only that it's not
compliant with 10G-Ethernet, but also that it's 1G-ethernet compliant.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the max coalesce timer setting that can be provided
by ethtool.
The default value (STMMAC_COAL_TX_TIMER) was used in the set_coalesce helper
instead of the max one (STMMAC_MAX_COAL_TX_TICK, so defined but not used).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't let T4 firmware flash on a T5 adapter and vice-versa
using ethtool
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SKB for a Tx packet is associated with an xgbe_ring_data structure
in the xgbe_map_tx_skb function. However, it is being saved in the
structure after the last structure used when the SKB is mapped. Use
the last used structure to save the SKB value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt value within the xgbe_ring_data structure is used as an
indicator of which Rx descriptor should have the INTE bit set to
generate an interrupt when that Rx descriptor is used. This bit was
mistakenly cleared in the xgbe_unmap_rdata function, effectively
nullifying the ethtool rx-frames support.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requesting an irq, the name passed in must be (part of) allocated
memory. The irq name was a local variable and resulted in random
characters when listing /proc/interrupts. Add a character field to the
xgbe_channel structure to hold the irq name and use that.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pretty straight-forward: convert all fields to/from
virtio endian-ness.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
TUN_ flags are internal and never exposed
to userspace. Any application using it is almost
certainly buggy.
Move them out to tun.c.
Note: we remove these completely in follow-up patches,
this code movement is split out for ease of review.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The spec states that mac in config space is only driver-writable in the
legacy case. Fence writing it in virtnet_set_mac_address() in the
virtio 1.0 case.
Suggested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
With VERSION_1 virtio_net uses same header size
whether mergeable buffers are enabled or not.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Our buffer length check is not strict enough for mergeable
buffers: buffer can still be shorter that header + address
by 2 bytes.
Fix that up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
virtio 1.0 doesn't use virtio_net_hdr anymore, and in fact, it's not
really useful since virtio_net_hdr_mrg_rxbuf includes that as the first
field anyway.
Let's drop it, precalculate header len and store within vi instead.
This way we can also remove struct skb_vnet_hdr.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Too many places poke at [rs]q->vq->vdev->priv just to get
the vi structure. Let's just pass the pointer around: seems
cleaner, and might even be faster.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Based on patches by Rusty Russell, Cornelia Huck.
Note: more code changes are needed for 1.0 support
(due to different header size).
So we don't advertize support for 1.0 yet.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch removes an extra rcu_read_unlock() on an allocation failure
in vnet_skb_shape(). The needed rcu_read_unlock() is already done in
the out_dropped label.
Reported-by: Rashmi Narasimhan <rashmi.narasimhan@oracle.com>
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPHY revision G0 has its version rolled over to 0x10, introduce an
explicit check for that revision and invoke the proper workaround
function for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with GPHY revision G0, the GENET register layout has changed to
use the same numbering scheme as the Starfighter 2 switch. This means
that GPHY major revision is in bits 15:12, minor in bits 11:8 and patch
level is in bits 7:4.
Introduce a small heuristic which checks for the old scheme first, tests
for the new scheme and finally attempts to catch reserved values and
aborts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TSO support for the sunvnet driver.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GSO support to the sunvnet driver.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for sender-side checksum offloading.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds scatter/gather support to the sunvnet driver.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for VIO v1.7 (extended descriptor format)
and v1.8 (receive-side checksumming) to the sunvnet driver.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the name of vnet_port_alloc_tx_bufs to
vnet_port_alloc_tx_ring, since there are no buffer allocations after
transmit zero copy support was added. This patch also moves the ring
allocation to after VIO version negotiation to allow for
different-sized descriptors in later VIO versions.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX HW is capable of using one of the following hash functions:
Toeplitz and an XOR hash function. This patch extends the implementation
of the mlx4_en driver set/get_rxfh callbacks to support getting and
setting the RSS hash function used by the device.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.
Fixes: 71f6d1b31f ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-12-06
This series contains updates to i40e and i40evf.
Shannon provides several patches to cleanup and fix i40e. First removes
an unneeded break statement in i40e_vsi_link_event(). Then removes
some debug messages that really do not give any useful information and
ends up getting printed every service_task loop, which fills the logfile
with noise when AQ tracing is enabled. Updates the aq_cmd arguments to
use %i which is much more forgiving and user friendly than the more
restrictive %x, or %d. Fixes the netdev_stat macro, where the old
xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated.
Getting the pf_id from the function number had an issue when
when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal. This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures. The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number.
Carolyn adds additional text description for the base pf0 and flow
director generated interrupts, since these interrupts are difficult
to distinguish per port on a multi-function device.
Jacob resolves an issue related to images with multiple PFs per
physical port. We cannot fully support 1588 PTP features, since only
one port should control (i.e. write) the registers at a time. Doing
so can cause interference of functionality.
Anjali provides several updates to i40e, first adds the Virtual Channel
OP event opcode for CONFIG_RSS, so that the Virtual Channel state
machine can properly decipher status change events. Then updates the
driver to add (and use) i40e_is_vf macro for future expansion when new
VF MAC types get added. Adds new update VSI flow to accommodate a
firmware dix with VSI loopback mode. All VSIs on a VEB should either
have loopback enabled or disabled, a mixed mode is not supported for a
VEB. Since our driver supports multiple VSIs per PF that need to talk to
each other make sure to enable Loopback for the PF and FDIR VSI as well.
Mitch provides a couple of i40e and i40evf patches. First updates
i40evf init code more adept at handling when multiple VFs attempt
to initialize simultaneously.
Joe Perches provides a i40e patch which resolves a compile warning
about about frame size being larger than 2048 bytes by reducing the
stack use by using kmemdup and not using a very large struct on the
stack.
v2:
- Dropped patch 13 & 14 while Mitch reworks the patches based on
feedback from Ben Hutchings, probably the tryptophan in the turkey
is to blame for the delay...
- Added Joe Perches patch which resolves a compile warning about frame
size
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace rtl_skb_pad with eth_skb_pad since they do the same thing.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update myri10ge to use eth_skb_pad helper. This also corrects a minor
issue as the driver was updating length without updating the tail pointer.
Cc: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the standard layout for padding an ethernet frame with the
eth_skb_pad call.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.
Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ConnectX-4LX to the list of supported devices as well as their virtual
functions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The outbox should be cleared before executing the command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command queue descriptor page size is 4KB and not the page size used by the
kernel.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 requires at least one interrupt vector for completions so fix the minvec
argument to pci_enable_msix_range() accordingly.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call request module on mlx5_ib so it will be available for applications
requiring it, such as installers that require boot over IB.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cmac engine is the bridge between driver and dash firmware.
Other os may not disable cmac when leave. And r8169 did not allocate any
resources for cmac engine. Disable it to prevent abnormal system behavior.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8168G/GU/H/EP and RTL8411B remove enable tx/rx from its own hw_start
function. This will prevent enable tx/rx before complete hardware tx/rx
setting.
Tx/Rx will be enabled in the end of function rtl_hw_start_8168.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify bcmgenet driver so that it can be used on Broadcom 7xxx
MIPS-based STB platforms without a device tree.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper handling of the vNIC hot removal event, which includes
a rescind-channel-offer message from the host side that triggers vNIC close and
removal. In this case, the notices to the host during close and removal is not
necessary because the channel is rescinded. This patch blocks these unnecessary
messages, and lets vNIC removal process complete normally.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing error state change handling with the new mechanism.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replacing error state change handling with the new mechanism.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replacing error state change handling with the new mechanism.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The handling of can error states is different between platforms.
This is an attempt to correct that problem.
I've moved this handling into a generic function for changing the
error state. This ensures that error state changes are handled
the same way everywhere (where this function is used).
This new mechanism also adds reverse state transitioning in error
frames, i.e. the user will be notified through the socket interface
when the state goes down.
Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix various spelling errors in the comments of the CAN modules.
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Several can modules in drivers/net/can use a banner[] variable at the
top which defines a string that is used once during init. This string
is also embedded with KERN_INFO which makes it printk() specific.
Improve the code by eliminating the banner[] variable and moving the
string to where it is printed. Then switch from printk(KERN_INFO to
pr_info() for the lines that were changed.
This patch is similar to [1] which was applied to net/can.
[1]: https://lkml.org/lkml/2014/11/22/10
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the endianess definition as well as the usage of the
multi-byte fields in the data structures exchanged with the PEAK-System USB
adapters.
By fixing the endianess, this patch also fixes the wrong usage of a 32-bits
local variable for handling the error status 16-bits field, in function
pcan_usb_pro_handle_error().
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch sets the correct reverse sequence order to the instructions
set to run, when any failure occurs during the initialization steps.
It also adds the missing unregistration call of the can device if the
failure appears after having been registered.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patchs fixes a misplaced call to memset() that fills the request
buffer with 0. The problem was with sending PCAN_USBPRO_REQ_FCT
requests, the content set by the caller was thus lost.
With this patch, the memory area is zeroed only when requesting info
from the device.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This reverts commit d32394fae9.
It has been reported to cause problems, Jeremiah writes:
On an Acer C720 laptop if a suspend is performed the screen
freezes, the machine locks up, and according to the indicator
lights it does not enter suspend. A hard reset is required to
get it running again.
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce stack use by using kmemdup and not using a very
large struct on stack.
In function ‘i40e_dbg_dump_desc’:
warning: the frame size of 8192 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Getting the pf_id from the function number was a good place to start,
but when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal. This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures. The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number. This works in NPAR mode as well.
Change-ID: I65e3dd6c97594890c2bad566b83cc670b1dae534
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ARQ needs to have at least as many entries as VFs, or the VFs will
get errors from the FW when they send messages to the PF. Since we don't
know how many VFs we'll end up with, just set up 128 descriptors.
Change-ID: I04ae3d1c7faf09110eb782214e9c05aeb62a6c59
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is an order in which this should happen. It turns out that FW will
not let you change the Loopback setting of the VSI with update VSI prior
to the VEB creation.
Change-ID: I7614ddff8b4c37702930c02f16f8c346aaa64bd1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All VSIs on a VEB should either have loopback enabled or disabled, a
mixed mode is not supported for a VEB. Since our driver supports multiple
VSIs per PF that need to talk to each other make sure to enable Loopback
for the PF and FDIR VSI as well.
Also, we now have to explicitly enable Loopback mode otherwise we fail
VSI creation for VMDq and VF VSIs.
Change-ID: Ib68c3ea4aeb730ac9468f930610de456efbe5b20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increase reset delay to ensure all internal caches are properly flushed
in worst case scenario.
Change-ID: I6f059a9e024fbf9ef1debd32497eed21369957fc
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When multiple VFs attempt to initialize simultaneously, the firmware may
delay or drop messages. Make the init code more adept at handling these
situations by a) reinitializing the admin queue if the firmware fails to
process a request, and b) resending a request if the PF doesn't answer.
Once the request has been sent again, the PF might end up getting both
requests and send the configuration information to the driver twice.
This will cause the VF to complain about receiving an unexpected message
from the PF. Since this is not fatal, reduce the warning level of the
log messages that are generated in response to this event.
Change-ID: I9370a1a2fde2ad3934fa25ccfd0545edfbbb4805
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The old xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated. Since we're
using rtnl_link_stats64 in other parts of the driver, we should use it
here as well. We've just been lucky that the field definitions are the
same sizes.
Change-ID: I19fc71619905700235dcdf0d3c8153aec81d36de
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is useful for future expansion when new VF MAC types get
added. It helps with cleaning up VF driver flow.
Change-ID: Ibe1eeb71262a3a40f24a1c5409436bdc3411da7f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Virtual Channel OP event opcode for CONFIG_RSS, so that the
Virtual Channel state machine can properly decipher status change events.
Change-ID: I09939c7aa380147f60c49fd01ef2e27d0dc1c299
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve an issue related to images with multiple PFs per physical
port. We cannot fully support 1588 PTP features, since only one port
should control (ie: write) the registers at a time. Doing so can cause
interference of functionality.
It may be possible to partially implement the API for only those
features without side effects. However, this at minimum means non
controlling PFs lose Tx timestamps, frequency atunement, and possibly
SYSTIME adjustment. There may be further impact I did not discover.
Since the API in the kernel expects these features to work, it is
simpler and less dangerous to just disable PTP features on all PFs not
identified as the controlling PF in PRTTSYN_CTL0.PF_ID.
This change also removes the warning printed when hwtstaml IOCTL is
called on the wrong PF. This is actually meaningless now, since only one
PF per port will support it. In addition, the ethtool get_ts_info IOCTL
was updated so that only the controlling port will even indicate support
(so as not to confuse users).
The overall downside is complete loss of functionality on non
controlling PF, vs the possible gain of partial support. The biggest
factor for choosing this approach is simplicity and ensuring that the
main PF will work. There could easily be other portions of the 1588
logic with side effects I am not aware, and the reduced functionality
that might be made available is significantly less useful. In addition,
the API does not allow for proper indication of why particular features
are not supported. These reasons are enough to decide for the simpler
approach to resolving this issue.
Change-ID: If4696bae686fc18aef6552b67dd417213d987c16
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds additional text description for base pf0 and flow director
generated interrupts. Without this patch, these interrupts are difficult
to distinguish per port on a multi-function device.
Change-ID: I4662e1b38840757765a3fe63d90219d28e76bfab
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the 'i' rather than the more restrictive 'x' or 'd' in the aq_cmd
arguments. This makes the user interface much more forgiving and user
friendly.
Change-ID: I5dcd57b9befc047e06b74cf1152a25a3fa9e1309
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This message really doesn't give any useful information and ends up
getting printed every service_task loop in the Linux driver, filling the
logfile with noise when AQ tracing is enabled. This patch simply removes
the noise.
Change-ID: I30ad51e6b03c7ad12a7d9c102def0087db622df3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This case statement is empty and the fall through just breaks out
so remove the break and let it fall through to break out.
Change-ID: I1b5ba9870d5245ca80bfca6e7f5f089e2eb8ccb0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To be more friendly with drop monitor, we should only call kfree_skb() when
the packets were dropped and use consume_skb() in other cases.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sky2_change_mtu setting B0_IMSK to 0 may be delayed due to PCI write posting
which could result in irqs being still active when synchronize_irq is called.
Since we are not prepared to handle any further irqs after synchronize_irq
(our resources are freed after that) force the write by a consecutive read from
the same register.
Similar situation in sky2_all_down: Here we disabled irqs by a write to B0_IMSK
but did not ensure that this write took place before synchronize_irq. Fix that
too.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a spurious interrupt dont forget to reenable the interrupts that
have been masked by reading the interrupt source register.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In pxa168_eth_open() the irqs are enabled before napi. This opens a tiny time
window in which the irq handler is processed, disables irqs but then is not able
to schedule the not yet activated napi, leaving irqs disabled forever (since
irqs are reenabled in napi poll function).
Fix this race by activating napi before irqs are activated.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pci_dev_put() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The free_percpu() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using global variables we are going to use dynamically allocated
memory. It allows to append a support of more than one ethernet adapter which
might have different settings simultaniously.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally broadcast mac address deauth is followed by stop_ap or start_ap.
In both cases, FW already has provision to send deauth; so there is no
need to handle broadcast mac deauthentication.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Station node entries should be guarded for whole of their reference
instead of just while getting node entry from station list.
It may happen that station node is retrieved may be deleted by
deauthentication event while it is still in use.
Reported by: Tim Shepard <shep@xplot.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to delete peer station's RA lists
upon station deautheticate event on AP interface. Patch also
decrements TX pending count upon removing packets from RA list.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A crash was observed while cfg80211 del_station handler is
called while stopping AP. This was happening because we were
deleting station list and Rx reorder table entries in del_sta
handler. While station entry is being deleted here, it may happen
that station deauth event from FW would also try to delete station
entry.
This patch fixes this crash by not deleting station entries in del_station
handler. Entry would be deleted while processing station deauth event; which
is triggered by del_station command to FW.
Reported by: Tim Shepard <shep@xplot.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch resolves couple of issues in ixgbevf_probe/remove():
1. Fix a case where adapter->state is tested after free_netdev() this is
same as the patch for ixgbe from Daniel Borkmann <dborkman@redhat.com>:
commit b5b2ffc057 ("ixgbe: fix use after free adapter->state test in ixgbe_remove/ixgbe_probe")
2. Move pci_set_drvdata() after all the error checks in ixgbevf_probe() and
then add a check in ixgbevf_probe() to avoid running the cleanup functions
twice in cases where probe failed.
CC: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds initial support for VFs on a new mac - X550.
The patch adds the basic structures and device IDs for the X550 VFs
that would allow the driver to load and pass traffic.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver has logic to free up used data in case any of the checks in
ixgbe_probe() fail, however there is a similar set of cleanups that can
occur on driver unload in ixgbe_remove() which can cause the rmmod command
to crash.
This patch aims to fix the logic by moving pci_set_drvdata() after all error
checks and then adds a check in ixgbe_remove() to skip it altogether if
adapter comes up empty.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we now support X550 mac's bump the version number to reflect this.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch extends the function pointer structure to include the new
X550 class MAC types. This creates a new file ixgbe_x550.c that contains
all of the new methods. Because of similarities to the X540 part in
some cases we just use it's methods where they can be used without any
modification. These exported functions are now defined in the new
ixgbe_x540.h file.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the shared code checksum calculation function only
returns a u16 and cannot return an error code. Unfortunately
a variety of errors can happen that completely prevent the
calculation of a checksum. So, change the function return value
from a u16 to an s32 and return a negative value on error, or the
positive checksum value when there is no error.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some X550 procedures will be using CS4227 PHY and need to
perform combined read and write operations. This patch
adds those methods.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550 hardware will use more bits in the mask, so change
the prototypes to match. This larger mask will require changes
in callers which use the higher bits. Likewise since X550 will
use different semaphore mask values and will use the lan_id
value. So save these values in the ixgbe_phy_info struct.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since on X550 we use host interface commands to read,write and erase
some commands require more time to complete. So this adds a timeout
parameter to ixgbe_host_interface_command as wells as a return_data
parameter allowing us to return with any data.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new X550 family of MAC's will have a larger RSS hash (16 -> 64).
It will also support individual VF to have their own independent RSS
hash key. This patch will enable this functionality
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accessing the CIAA/D register can block access to the PCI config space.
This patch removes the read/write operations to the CIAA/D registers
and makes use of standard kernel functions for accessing the PCI config
space.
In addition it moves ixgbevf_check_for_bad_vf() into the watchdog subtask
which reduces the frequency of the checks.
CC: Alex Williamson <alex.williamson@redhat.com>
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Attempt to look up the MAC address in Open Firmware on systems that
support it. On SPARC resort to using the IDPROM if no OF address is
found.
Signed-off-by: Martin K Petersen <martin.petersen@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the tail writes for the ixgbe descriptor queues. The
current implementation had me confused as I wasn't sure if it was still
making use of the surprise remove logic or not.
It also adds the mmiowb which is needed on ia64, mips, and a couple other
architectures in order to synchronize the MMIO writes with the Tx queue
_xmit_lock spinlock.
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the page reuse code getting it into a state where all
the workarounds needed are in place as well as cleaning up a few minor
oversights such as using __free_pages instead of put_page to drop a locally
allocated page.
It also cleans up how we clear the descriptor status bits. Previously they
were zeroed as a part of clearing the hdr_addr. However the hdr_addr is a
64 bit field and 64 bit writes can be a bit more expensive on on 32 bit
systems. Since we are no longer using the header split feature the upper
32 bits of the address no longer need to be cleared. As a result we can
just clear the status bits and leave the length and VLAN fields as-is which
should provide more information in debugging.
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME within #ifdef blocks depending on
CONFIG_PM may be dropped now.
Do that in the e1000e and igb network drivers.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for multiple BSS interfaces (AP). In
total three AP configurations can be created. In order to use
multiple BSS firmware needs to support it.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor specific commands was always using main interface,
change this to use the by caller supplied interface.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use single message MSI to replace legacy interrupt.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some 43602 devices are band specific and identify themselves
with different PCIE device ID. This patch adds support for the
43602 2.4G and 5.0G devices used in for example R8000 router.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ifidx provided by FW needs to be offsetted when receiving data
packets.
Cc: stable@vger.kernel.org # v3.17, v3.18
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wake On Lan was not working on laptop DELL Vostro 1500.
If WOL was turned on, BCM4401 was powered up in suspend mode. LEDs blinked.
But the laptop could not be woken up with the Magic Packet. The reason for
that was that PCIE was not enabled as a system wakeup source and
therefore the host PCI bridge was not powered up in suspend mode.
PCIE was not enabled in suspend by PM because no child devices were
registered as wakeup source during suspend process.
On laptop BCM4401 is connected through the SSB bus, that is connected to the
PCI-Express bus. SSB and B44 did not use standard PM wakeup functions
and did not forward wakeup settings to their parents.
To fix that B44 driver enables PM wakeup and registers new wakeup source
using device_set_wakeup_enable(). Wakeup is automatically reported to the parent SSB
bus via power.wakeup_path. SSB bus enables wakeup for the parent PCI bridge, if there is any
child devices with enabled wakeup functionality. All other steps are
done by PM core code.
Signed-off-by: Andrey Skvortsov <Andrej.Skvortzov@gmail.com>
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg <johannes@sipsolutions.net> says:
"This time I have Felix's no-status rate control work, which will allow
drivers to work better with rate control even if they don't have perfect
status reporting. In addition to this, a small hwsim fix from Patrik,
one of the regulatory patches from Arik, and a number of cleanups and
fixes I did myself.
Of note is a patch where I disable CFG80211_WEXT so that compatibility
is no longer selectable - this is intended as a wake-up call for anyone
who's still using it, and is still easily worked around (it's a one-line
patch) before we fully remove the code as well in the future."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we write the GSO meta-data in tun_get_user we end up advancing
the IO vector twice, thus exhausting the user buffer before we can
finish writing the packet.
Fixes: f5ff53b4d9 ("{macvtap,tun}_get_user(): switch to iov_iter")
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silences various sparse warnings
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rocker ports will use new "swdev" hwmode for bridge port offload policy.
Current supported policy settings are BR_LEARNING and BR_LEARNING_SYNC.
User can turn on/off device port FDB learning and syncing to bridge.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add L2 bridge offloading support to rocker driver. Here, the Linux bridge
driver is used to collect swdev ports into a tagged (or untagged) VLAN
bridge. The switchdev will offload from the bridge driver the following L2
bridging functions:
- Learning of neighbor MAC addresses on VLAN X Learned mac/vlan is
installed in bridge FDB. (And removed when device unlearns mac/vlan).
Learning must be turned off on each bridge port to disable the feature in
the bridge driver.
- Flooding of multicast/broadcast and unknown unicast pkts to (STP)
active ports in bridge. The bridge driver is unaware of the flooding happening
at the device level. Flooding must be turned off on each bridge port to
disable the feature on the bridge driver.
- STP port state is pushed down to driver/device. The bridge still processes
STP BDPUs and maintains port STP state (for all VLANs in bridge), but
the driver/device must be notified of port STP state change to program
the device.
Multiple (VLAN) bridges are supported. The device (implemented per
the OF-DPA spec) must use a portion of the VLAN namespace for
internal VLANs. Right now, the upper 255 VLANs (0xf00 to 0xffe) are
used as internal VLAN IDs for untagged traffic and are not available
as port VLANs.
The driver uses the following interfaces:
1. To track VLAN add/del on ports in bridge:
.ndo_vlan_rx_add_vid
.ndo_vlan_rx_kill_vid
2. To track port add/del membership in bridge:
NETDEV_CHANGEUPPER netdevice notifier
3. To catch static FDB entries installed on bridge/vlan by user using netlink:
.ndo_fdb_add
.ndo_fdb_del
4. To be notified on port STP state change:
.ndo_switch_port_stp_update
5. To notify bridge driver on learned/forgotten mac/vlans on bridge port:
br_fdb_external_learn_add
br_fdb_external_learn_del
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rocker driver maintains 4 hash tables: flows, groups, FDB, and VLANs.
Flow and group tables track the entries installed to OF-DPA tables,
per the OF-DPA spec. See OF-DPA spec for full description of fields
in each flow and group table. New table entries are pushed to the
device with ADD cmd. Updated entries are pushed to the device with
MOD cmd. For flow table entries, a crc32 key is made from fields of
the particular field. For group table entries, the group_id is used
as the key.
The FDB table tracks fdb entries learned by the device or manually
pushed to the bridge by the user. A crc32 key is made from the
port/mac/vlan tuple for the fdb entry.
The VLAN table tracks the ifindex-to-internal-vlan mapping for
untagged pkts. On ingress, an untagged pkt is inserted with an
internal VLAN ID based on the input port's current internal VLAN ID.
The input port's internal VLAN will either be referenced by the port's
ifindex, if not bridged, or the containing bridge's ifindex, if
bridged. Since the ifindex space isn't within a fixed range, uses a
hash table (with ifindex as key) to track internal VLAN ID for a given
ifindex. The internal VLAN ID range is fixed and currently uses the
upper 255 VLAN IDs, starting at 0xf00.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the first driver to benefit from the switchdev
infrastructure and to implement newly introduced switch ndos. This is a
driver for emulated switch chip implemented in qemu:
https://github.com/sfeldma/qemu-rocker/
This patch is a result of joint work with Scott Feldman.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow brport device to return current brport flags set on port. Add
returned flags to nested IFLA_PROTINFO netlink msg built in dflt getlink.
With this change, netlink msg returned for bridge_getlink contains the port's
offloaded flag settings (the port's SELF settings).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.
Fixes: f36c374782 ("xen/netfront: handle compound page fragments on transmit")
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Along with that I have a new activity, we have now better
infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rVs8
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-john-2014-12-02' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
"Grumbach, Emmanuel" <emmanuel.grumbach@intel.com> says:
"I deprecate here -8.ucode since -9 has been published long ago.
Along with that I have a new activity, we have now better
infrastructure for firmware debugging. This will allow to
have configurable probes insides the firmware.
Luca continues his work on NetDetect, this feature is now
complete. All the rest is minor fixes here and there."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new ucode package format holds also the usniffer images
(in addition to the operational images and the TLVs).
The driver can load the usniffer image if debug
configuration tells it to.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Until this patch, dumping the monitor data could be done only
for PCIe external (DRAM) mode in 7000 HW family. This patch
allows to pull the monitor data also on other families, and
also to pull the monitor data if an internal buffer is used.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Sometimes there is a need to configure some registers for
setting some FW properties, such as the FW monitor mode
(internal/external). This patch supports setting this for
PCIe mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Send all debug-configuration HCMDs that are set in the TLVs
to the FW. This may include HCMDs to configure the FW
monitor and FW log level, for example.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Debug information can be appended to the firmware file. This
information will be used by the driver to enable / disable
debugging features in the firmware.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since the commit below, iwldvm sends the FLUSH command to
the firmware. All the devices that use iwldvm have a
firmware that expects the _v3 version of this command,
besides 5150.
5150's latest available firmware still expects a _v2 version
of the FLUSH command.
This means that since the commit below, we had a mismatch for
this specific device only.
This mismatch led to the NMI below:
Loaded firmware version: 8.24.2.2
Start IWL Error Log Dump:
Status: 0x0000004C, count: 5
0x00000004 | NMI_INTERRUPT_WDG
0x000006F4 | uPc
0x000005BA | branchlink1
0x000006F8 | branchlink2
0x000008C2 | interruptlink1
0x00005B02 | interruptlink2
0x00000002 | data1
0x07030000 | data2
0x00000068 | line
0x3E80510C | beacon time
0x728A0EF4 | tsf low
0x0000002A | tsf hi
0x00000000 | time gp1
0x01BDC977 | time gp2
0x00000000 | time gp3
0x00010818 | uCode version
0x00000000 | hw version
0x00484704 | board version
0x00000002 | hcmd
0x2FF23080 | isr0
0x0103E000 | isr1
0x0000001A | isr2
0x1443FCC3 | isr3
0x11800112 | isr4
0x00000068 | isr_pref
0x000000D4 | wait_event
0x00000000 | l2p_control
0x00000007 | l2p_duration
0x00103040 | l2p_mhvalid
0x00000007 | l2p_addr_match
0x00000000 | lmpm_pmg_sel
0x00000000 | timestamp
0x00000200 | flow_handler
This was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=88961
Cc: <stable@vger.kernel.org>
Fixes: a0855054e5 ("iwlwifi: dvm: drop non VO frames when flushing")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In 8000 B-step the FW file has changed, but by the time we
know the HW step, the FW file is already requested.
This patch defaults 8000 family to B-step if no HW step is
detected in time. When it can it checks what HW step it
really is (in 8000 family) and if it isn't B-step, the FW
file is released and the A-step file is requested.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix the 4165 series name that was called 4265 by mistake.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Hardware doesn't place any restrictions on the buffer alignment,
consider this TODO resolved.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If card reset with firmware download executed, followed by reset
with use of firmware from build in flash, firmware download indication
remains in the hardware register.
When running firmware download flow,
the SW download indication is written by the driver to bit 0 in usage_6:
wil_fw_load(), "S(RGF_USER_USAGE_6, 1);"
This register, like all USER RGF, wasn't reset in SW reset flow.
Therefore the driver must clear it on SW reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_tx_ring, error message printed when tx attempted
while vring has no space to accommodate all fragments of frame.
Normally, such situation handled by stopping tx queue.
But, if tx queue is by-passed (like pktgen does), this error
will be triggered at high rate and dmesg will be flooded with
this message. Whole system may become unstable and hang with
no possible recover except power cycle.
Rate-limit it to prevent dmesg flooding.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some compilation environments, result of pointer arithmetic interpreted as int
while in others it is long int. Force conversion to long.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to configure VRING size for both Rx and Tx via module parameters:
rx_ring_order and tx_ring_order. Parameters are ring size orders, i.e.
ring size calculated as 1 << order.
Defaults for both Tx and Rx are order 9, i.e. size 512
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to obtain physical device through
wil->pdev->dev path, as it is done by this macro.
The same device already stored as wiphy's device, thus
wil_to_dev() returns the same device as wil_to_pcie_dev()
Remove unnecessary macros, this allows to drop dependency
by pci.h in the firmware download code.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scan timeout treated as indication for firmware error;
and should be handled in the same way.
Recovery state machine does not perform as designed because
its state is not updated in case of scan timeout.
Fix is to set recovery state machine into the proper state.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_HTRSH interrupt is handled in exactly the same manner
as RX_DONE interrupt - fetching accumulated packets from RX
ring. In addition there's a rate limitted warning message.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Propagate reason for the disconnect through the relevant call chains:
- report to cfg80211 reason as reported by the firmware
- provide to the firmware reason as requested by cfg80211
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of killing interrupts during reset when the first one happens,
kill them before issuing the reset.
This fixes an easy to reproduce crash with multiple cards sharing the
same IRQ.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IRQs are suppressed if ah == NULL and ATH_OP_INVALID being set in
common->op_flags. Close a short time window between those two.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.
Cc: stable@vger.kernel.org
Reported-by: Hubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
