There are three types of messages between w1 core and userspace:
1. Events. They are generated each time new master or slave device found
either due to automatic or requested search.
2. Userspace commands. Includes read/write and search/alarm search comamnds.
3. Replies to userspace commands.
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Special file in each w1 slave device's directory called "rw" is created
each time new slave and no appropriate w1 family is registered.
"rw" file supports read and write operations, which allows to perform
almost any kind of operations. Each logical operation is a transaction
in nature, which can contain several (two or one) low-level operations.
Let's see how one can read EEPROM context:
1. one must write control buffer, i.e. buffer containing command byte
and two byte address. At this step bus is reset and appropriate device
is selected using either W1_SKIP_ROM or W1_MATCH_ROM command.
Then provided control buffer is being written to the wire.
2. reading. This will issue reading eeprom response.
It is possible that between 1. and 2. w1 master thread will reset bus for
searching and slave device will be even removed, but in this case 0xff will
be read, since no device was selected.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements support for the National Semiconductor LM70
temperature sensor.
The LM70 temperature sensor chip supports a single temperature sensor.
It communicates with a host processor (or microcontroller) via an
SPI/Microwire Bus interface.
Communication with the LM70 is simple: when the temperature is to be sensed,
the driver accesses the LM70 using SPI communication: 16 SCLK cycles
comprise the MOSI/MISO loop. At the end of the transfer, the 11-bit 2's
complement digital temperature (sent via the SIO line), is available in the
driver for interpretation. This driver makes use of the kernel's in-core
SPI support.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-i801: Remove force_addr parameter
Remove the force_addr module parameter. It doesn't appear to ever
have been needed, and PCI resources shouldn't be arbitrarily
changed anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New hardware monitoring driver for the Abit uGuru
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reword and complete certain parts of the hwmon sysfs-interface
documentation file. Hopefully this will make things clearer for new
driver authors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up hwmon sysfs documentation file, plus introduces
the description of DC/PWM selection for fan speed control.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch adds support for the OpenCores I2C controller IP
core (See http://www.opencores.org/projects.cgi/web/i2c/overview).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Improve the help text for CONFIG_HWMON to let the users know how they
pick the right hardware monitoring driver(s) for their system.
Also fix a couple typos in the related documentation file and improve
some parts a bit.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One more motherboard confirmed to have an LM83 temperature sensor chip.
Thanks to Steven Hardy for reporting.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the w83791d sensor chip. The w83791d hardware is
somewhere between the w83781d and the w83792d and this driver code
is derived from the code that supports those chips.
Signed-off-by: Charles Spirakis <bezaur@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the new nForce4 MCP51 (also known as nForce 410 or
430) and nForce4 MCP55 to the i2c-nforce2 driver. Some code changes
were required because the base I/O address registers have changed in
these versions. Standard BARs are now being used, while the original
nForce2 chips used non-standard ones.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Properly document on which systems the i2c-piix4 SMBus driver will
refuse to load. Hopefully this will make it clearer for users, which
were often wondering why their destop or server systems were detected
as laptops.
Closes bug #6429.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the fix_hstcfg option from the driver and related
SMBus Interrupt Select register magic because now we know what are
valid values for this register. This patch updates the documentation
and adds new IRQ mode check so we are sure not to miss any new
"unusual" value.
The PCI quirk for users of fix_hstcfg was not developed because the
chipset lacks of subsystem ID registers and DMI is stated "To be
filled". Impact to existing systems is minimal because the problem
showed up on motherboards like 10 years back. On the other hand users
of newer Serverworks and HT1000 systems won't be misleaded by the
message suggesting to try the fix_hstcfg any more.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the ATI IXP southbridges support to i2c-piix4,
as it turned out those chips are compatible with it.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extend the sysfs interface of hardware monitoring chips, by adding
individual alarm and beep files. Contrary to the old aggregated "alarms"
and "beeps" files, individual files constitute a standard way to access
the status information, making it finally possible to implement a
chip-independant hardware monitoring chip access library (once all
drivers have been added this new interface, that is.)
If future drivers need more individual files, the interface will be
extended as needed at the same time these drivers are merged into the
kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New driver (smsc47m192) which supports voltage and temperature
measurement features of SMSC LPC47M192 and LPC47M997 chips.
Signed-off-by: Hartmut Rick <linux@rick.claranet.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add LM82 temperature sensor support (similar to the LM83,
but less featureful).
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the documentation. Apparently, I left unedited copy-paste results
in examples. Also, Alan helped me to improve the most confusing parts.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The swsusp.txt documentation harshes confusingly on USB, and this patch
addresses the issue. It's harsh because it blames USB for some issues
that are generic to all drivers -- especially those supporting removable
media -- and it's confusing since it says that USB has the issue with
"suspend" not just swsusp ... while in reality, USB doesn't have the
issue when real system suspend states are used.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using the class device pointer returned by tty_register_device() with
part 1 of the patch, attach the Gigaset drivers' "cidmode" sysfs entry
to its tty class device, where it can be found more easily by users
who do not know nor care which USB port the device is attached to.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Thu, Jun 01, 2006 at 02:46:11AM -0700, Rajesh Shah wrote:
> This patch assumes that pci_request_region() will always be called
> after pci_enable_device() and pci_release_region() will always
> be called before pci_disable_device(). We cannot make this
> assumption,since it's perfectly legal to disable a device
> first and then release it's regions. So, I think that patch
> needs to change.
Patch below clarifies comments in Documentation/pci.txt.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bcollins/linux1394-2.6: (28 commits)
eth1394: replace __constant_htons by htons
ieee1394: adjust code formatting in highlevel.c
ieee1394: hl_irqs_lock is taken in hardware interrupt context
ieee1394_core: switch to kthread API
ieee1394: sbp2: Kconfig fix
ieee1394: add preprocessor constant for invalid csr address
sbp2: fix deregistration of status fifo address space
[PATCH] eth1394: endian fixes
Fix broken suspend/resume in ohci1394
sbp2: use __attribute__((packed)) for on-the-wire structures
sbp2: provide helptext for CONFIG_IEEE1394_SBP2_PHYS_DMA and mark it experimental
Update feature removal of obsolete raw1394 ISO requests.
sbp2: fix S800 transfers if phys_dma is off
sbp2: remove ohci1394 specific constant
ohci1394: make phys_dma parameter read-only
ohci1394: set address range properties
ieee1394: extend lowlevel API for address range properties
sbp2: log number of supported concurrent logins
sbp2: remove manipulation of inquiry response
ieee1394: save RAM by using a single tlabel for broadcast transactions
...
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
[ARM] 3559/1: S3C2442: core and serial port
[ARM] 3557/1: S3C24XX: centralise and cleanup uart registration
[ARM] 3558/1: SMDK24XX: LED platform devices
[ARM] 3534/1: add spi support to lubbock platform
[ARM] 3554/1: ARM: Fix dyntick locking
[ARM] 3553/1: S3C24XX: earlier print of cpu idcode info
[ARM] 3552/1: S3C24XX: Move VA of GPIO for low-level debug
[ARM] 3551/1: S3C24XX: PM code failes to compile with CONFIG_DCACHE_WRITETHROUGH
[ARM] 3550/1: OSIRIS: fix serial port map for 1:1
[ARM] 3548/1: Fix the ARMv6 CPU id in compressed/head.S
[ARM] 3335/1: Old-abi Thumb sys_syscall broken
[ARM] 3467/1: [3/3] Support for Philips PNX4008 platform: defconfig
[ARM] 3466/1: [2/3] Support for Philips PNX4008 platform: chip support
[ARM] 3465/1: [1/3] Support for Philips PNX4008 platform: headers
[ARM] 3407/1: lpd7x: documetation update
[ARM] 3406/1: lpd7x: compilation fix for smc91x
[ARM] 3405/1: lpd7a40x: CPLD ssp driver
[ARM] 3404/1: lpd7a40x: AMBA CLCD support
[ARM] 3403/1: lpd7a40x: updated default configurations
[ARM] 3402/1: lpd7a40x: serial driver bug fix
...
Update kernel documentation to include a description of the inotify
kernel API.
Signed-off-by: Amy Griffis <amy.griffis@hp.com>
Acked-by: Robert Love <rml@novell.com>
Acked-by: John McCutchan <john@johnmccutchan.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (51 commits)
[MIPS] Make timer interrupt frequency configurable from kconfig.
[MIPS] Correct HAL2 Kconfig description
[MIPS] Fix R4K cache macro names
[MIPS] Add Missing R4K Cache Macros to IP27 & IP32
[MIPS] Support for the RM9000-based Basler eXcite smart camera platform.
[MIPS] Support for the R5500-based NEC EMMA2RH Mark-eins board
[MIPS] Support SNI RM200C SNI in big endian mode and R5000 processors.
[MIPS] SN: include asm/sn/types.h for nasid_t.
[MIPS] Random fixes for sb1250
[MIPS] Fix bcm1480 compile
[MIPS] Remove support for NEC DDB5476.
[MIPS] Remove support for NEC DDB5074.
[MIPS] Cleanup memory managment initialization.
[MIPS] SN: Declare bridge_pci_ops.
[MIPS] Remove unused function alloc_pci_controller.
[MIPS] IP27: Extract pci_ops into separate file.
[MIPS] IP27: Use symbolic constants instead of magic numbers.
[MIPS] vr41xx: remove unnecessay items from vr41xx/Kconfig.
[MIPS] IP27: Cleanup N/M mode configuration.
[MIPS] IP27: Throw away old unused hacks.
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (109 commits)
[ETHTOOL]: Fix UFO typo
[SCTP]: Fix persistent slowdown in sctp when a gap ack consumes rx buffer.
[SCTP]: Send only 1 window update SACK per message.
[SCTP]: Don't do CRC32C checksum over loopback.
[SCTP] Reset rtt_in_progress for the chunk when processing its sack.
[SCTP]: Reject sctp packets with broadcast addresses.
[SCTP]: Limit association max_retrans setting in setsockopt.
[PFKEYV2]: Fix inconsistent typing in struct sadb_x_kmprivate.
[IPV6]: Sum real space for RTAs.
[IRDA]: Use put_unaligned() in irlmp_do_discovery().
[BRIDGE]: Add support for NETIF_F_HW_CSUM devices
[NET]: Add NETIF_F_GEN_CSUM and NETIF_F_ALL_CSUM
[TG3]: Convert to non-LLTX
[TG3]: Remove unnecessary tx_lock
[TCP]: Add tcp_slow_start_after_idle sysctl.
[BNX2]: Update version and reldate
[BNX2]: Use CPU native page size
[BNX2]: Use compressed firmware
[BNX2]: Add firmware decompression
[BNX2]: Allow WoL settings on new 5708 chips
...
Manual fixup for conflict in drivers/net/tulip/winbond-840.c
Received From Mark Salyzyn
Some of the cards product names changed.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Marc Singer
New documentation for the touchscreen controllers and LCD panels.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A lot of people have asked for a way to disable tcp_cwnd_restart(),
and it seems reasonable to add a sysctl to do that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Various drivers use xmit_lock internally to synchronise with their
transmission routines. They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.
With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set. This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.
While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire. So
delaying or dropping the message is to be avoided as much as possible.
So the only alternative is to always set xmit_lock_owner. The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.
I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly. I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.
This is pretty much a straight text substitution except for a small
bug fix in winbond. It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission. This is
unsafe as an IRQ can potentially wake up the queue. So it is safer to
use netif_tx_disable.
The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new per-packet access controls to SELinux, replacing the old
packet controls.
Packets are labeled with the iptables SECMARK and CONNSECMARK targets,
then security policy for the packets is enforced with these controls.
To allow for a smooth transition to the new controls, the old code is
still present, but not active by default. To restore previous
behavior, the old controls may be activated at runtime by writing a
'1' to /selinux/compat_net, and also via the kernel boot parameter
selinux_compat_net. Switching between the network control models
requires the security load_policy permission. The old controls will
probably eventually be removed and any continued use is discouraged.
With this patch, the new secmark controls for SElinux are disabled by
default, so existing behavior is entirely preserved, and the user is
not affected at all.
It also provides a config option to enable the secmark controls by
default (which can always be overridden at boot and runtime). It is
also noted in the kconfig help that the user will need updated
userspace if enabling secmark controls for SELinux and that they'll
probably need the SECMARK and CONNMARK targets, and conntrack protocol
helpers, although such decisions are beyond the scope of kernel
configuration.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: David Howells <dhowells@redhat.com>
Apply some alterations to the memory barrier document that I worked out
with Paul McKenney of IBM, plus some of the alterations suggested by Alan
Stern.
The following changes were made:
(*) One of the examples given for what can happen with overlapping memory
barriers was wrong.
(*) The description of general memory barriers said that a general barrier is
a combination of a read barrier and a write barrier. This isn't entirely
true: it implies both, but is more than a combination of both.
(*) The first example in the "SMP Barrier Pairing" section was wrong: the
loads around the read barrier need to touch the memory locations in the
opposite order to the stores around the write barrier.
(*) Added a note to make explicit that the loads should be in reverse order to
the stores.
(*) Adjusted the diagrams in the "Examples Of Memory Barrier Sequences"
section to make them clearer. Added a couple of diagrams to make it more
clear as to how it could go wrong without the barrier.
(*) Added a section on memory speculation.
(*) Dropped any references to memory allocation routines doing memory
barriers. They may do sometimes, but it can't be relied on. This may be
worthy of further documentation later.
(*) Made the fact that a LOCK followed by an UNLOCK should not be considered a
full memory barrier more explicit and gave an example.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpqfc driver flushed out with: [SCSI] remove broken driver cpqfc (commit
ca61f10ab2) but somehow
Documentation/scsi/cpqfc.txt managed to survive the blast.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
HighPoint RocketRAID 3220/3320 series 8 channel PCI-X SATA RAID Host
Adapters.
Fixes from original submission:
Merge Andrew Morton's patches:
- Provide locking for global list
- Fix debug printks
- uninline function with multiple callsites
- coding style fixups
- remove unneeded casts of void*
- kfree(NULL) is legal
- Don't "succeed" if register_chrdev() failed - otherwise we'll later
unregister a not-registered chrdev.
- Don't return from hptiop_do_ioctl() with the spinlock held.
- uninline __hpt_do_ioctl()
Update for Arjan van de Ven's comments:
- put all asm/ includes after the linux/ ones
- replace mdelay with msleep
- add pci posting flush
- do not set pci command reqister in map_pci_bar
- do not try merging sg elements in hptiop_buildsgl()
- remove unused outstandingcommands member from hba structure
- remove unimplemented hptiop_abort() handler
- remove typedef u32 hpt_id_t
Other updates:
- fix endianess
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bonding documentation needed an update to include sysfs specific
information. This patch adds information on how to change bonding
parameters at runtime using the sysfs interface.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This patch( originally submitted by Christoph Hellwig) removes
instance_lock and changes fw_outstanding variable data type to
atomic_t.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update documentation to match reality. INPCK controls whether input
parity checking is enabled.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove the following global function that is both unused and
unimplemented:
- register_firmware()
- make the following needlessly global function static:
- firmware_class_uevent()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Grand unification of the three types of workarounds we have so far.
The "skip mode page 8" workaround is now limited to devices which
pretend to be of TYPE_DISK instead of TYPE_RBC. This workaround is no
longer enabled for Initio bridges.
Patch update in anticipation of more workarounds:
- Add module parameter "workarounds".
- Deprecate parameter "force_inquiry_hack".
- Compose the blacklist of a compound type for better readability and
extensibility.
- Remove a now unused #define.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to be able to have a "SPI bus 0" matching chip numbering; but
that number was wrongly used to flag dynamic allocation of a bus number.
This patch resolves that issue; now negative numbers trigger dynamic alloc.
It also updates the how-to-write-a-controller-driver overview to mention
this stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary). The driver has the following
features:
- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the simple watchdog daemon program in Doc/watchdog/watchdog-api.txt
to build cleanly.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Changing the driver to use dynamic device numbers was one of the many
changes that were made in order to have the driver accepted into the
mainline kernel. Therefore I would say that the entry in devices.txt is
obsolete. This patch removes it.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Cc: Torben Mathiasen <device@lanana.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
BBTI has updated their driver, and removed the old one from their website.
This patch updates the get_dvb_firmware script to download the firmware
from the new driver location.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
[IPV6]: skb leakage in inet6_csk_xmit
[BRIDGE]: Do sysfs registration inside rtnl.
[NET]: Do sysfs registration as part of register_netdevice.
[TG3]: Fix possible NULL deref in tg3_run_loopback().
[NET] linkwatch: Handle jiffies wrap-around
[IRDA]: Switching to a workqueue for the SIR work
[IRDA]: smsc-ircc: Minimal hotplug support.
[IRDA]: Removing unused EXPORT_SYMBOLs
[IRDA]: New maintainer.
[NET]: Make netdev_chain a raw notifier.
[IPV4]: ip_options_fragment() has no effect on fragmentation
[NET]: Add missing operstates documentation.
This closes a couple holes in our attribute aliasing avoidance scheme:
- The current kernel fails mmaps of some /dev/mem MMIO regions because
they don't appear in the EFI memory map. This keeps X from working
on the Intel Tiger box.
- The current kernel allows UC mmap of the 0-1MB region of
/sys/.../legacy_mem even when the chipset doesn't support UC
access. This causes an MCA when starting X on HP rx7620 and rx8620
boxes in the default configuration.
There's more detail in the Documentation/ia64/aliasing.txt file this
adds, but the general idea is that if a region might be covered by
a granule-sized kernel identity mapping, any access via /dev/mem or
mmap must use the same attribute as the identity mapping.
Otherwise, we fall back to using an attribute that is supported
according to the EFI memory map, or to using UC if the EFI memory
map doesn't mention the region.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsa: (22 commits)
[ALSA] via82xx - Use DXS_SRC as default for VIA8235/8237/8251 chips
[ALSA] hda-codec - Add model entry for ASUS Z62F
[ALSA] PCMCIA sound devices shouldn't depend on ISA
[ALSA] hda-codec - Fix capture from line-in on VAIO SZ/FE laptops
[ALSA] Fix Oops at rmmod with CONFIG_SND_VERBOSE_PROCFS=n
[ALSA] PCM core - introduce CONFIG_SND_PCM_XRUN_DEBUG
[ALSA] adding __devinitdata to pci_device_id
[ALSA] add __devinitdata to all pci_device_id
[ALSA] hda-codec - Add codec id for AD1988B codec chip
[ALSA] hda-codec - Add model entry for ASUS M9 laptop
[ALSA] pcxhr - Fix a compiler warning on 64bit architectures
[ALSA] via82xx: tweak VT8251 workaround
[ALSA] intel8x0 - Disable ALI5455 SPDIF-input
[ALSA] via82xx: add support for VIA VT8251 (AC'97)
[ALSA] Fix typos and add information about Jack support to Audiophile-Usb.txt
[ALSA] Fix double free in error path of miro driver
[ALSA] hda-codec - Add entry for Epox EP-5LDA+ GLi
[ALSA] sound/pci/: remove duplicate #include's
[ALSA] hda-codec - Use model 'hp' for all HP laptops with AD1981HD
[ALSA] continue on IS_ERR from platform device registration
...
As reported in Bugzilla Bug 6406, resume from S3 results in a blank screen.
For the IBM Thinkpad X30 using vesafb as the console driver, successful resume
from S3 requires option acpi_sleep=s3_bios,s3_mode. Update documentation.
I would presume that, in any hardware, using vesafb as the console driver will
require as a minimum s3_mode.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: <igor47@uchicago.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] PCI quirk: VIA IRQ fixup should only run for VIA southbridges
[PATCH] PCI: fix potential resource leak in drivers/pci/msi.c
[PATCH] PCI: Documentation: no more device ids
[PATCH] PCI: fix via irq SATA patch
Document that we don't like to add more PCI device ids
but are happy to accept PCI vendor ids for linux/include/pci_ids.h
Original text from Jeff Garzik.
Signed-off-by: Ingo Oeser <netdev@axxeo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refering to <kernelsource>/Documentation/pci.txt
the struct pci_device_id can be released after loading the module.
Signed-off-by: Kenrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When abort failed, the driver gets reset handleer called. In the reset
handler, driver calls 'scsi_done()' callback for same SCSI command packet
(struct scsi_cmnd) multiple times if there are multiple SCSI command packet
in the pend_list. More over, if there are entry in the pend_lsit with
IOCTL packet associated, the driver returns it to wrong free_list so that,
in turn, the driver could end up with 'NULL pointer dereference..' during
I/O command building with incorrect resource.
Also, the patch contains several minor/cosmetic changes besides this.
Signed-off-by: Seokmann Ju <seokmann.ju@lsil.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Update the schedule for the removal of drivers depending on
OBSOLETE_OSS_DRIVER as follows:
- adjust OBSOLETE_OSS_DRIVER dependencie
- from the release of 2.6.16 till the release of 2.6.17:
approx. two months for users to report problems with the ALSA
drivers for the same hardware
- after the release of 2.6.17 (and before 2.6.18):
remove the subset of drivers marked at OBSOLETE_OSS_DRIVER without
known regressions in the ALSA drivers for the same hardware
Additionally, correct some OBSOLETE_OSS_DRIVER dependencies.
A rationale of the changes is in
http://lkml.org/lkml/2006/1/28/135
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We added the ability to change a block device's IO elevator scheduler both
at kernel boot and on-the-fly, but we only documented the elevator= boot
parameter. Add a quick how-to on doing it on the fly.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jens Axboe <axboe@suse.de>
Add new line of /proc/meminfo output.
Explain the HugePage_ lines in /proc/meminfo (from Bill Irwin).
Change KB to kB since the latter is what is used in the kernel.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improve serial driver documentation:
- Remove CVS id.
- Update pointer to reference driver documentation.
- Add comments about new uart_write_console function.
- Add TIOCM_LOOP modem control bit description.
- Add commentry about enable_ms method being called multiple times.
- Add commentry about startup/shutdown method calling.
- Mention that dereferencing port->info after shutdown is invalid.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (170 commits)
commit 3d9dd7564d
Author: Zach Brown <zach.brown@oracle.com>
Date: Fri Apr 14 16:04:18 2006 -0700
[PATCH] ip_output: account for fraggap when checking to add trailer_len
During other work I noticed that ip_append_data() seemed to be forgetting to
include the frag gap in its calculation of a fragment that consumes the rest of
the payload. Herbert confirmed that this was a bug that snuck in during a
previous rework.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 08d099974a
Author: Linus Walleij <triad@df.lth.se>
Date: Fri Apr 14 16:03:33 2006 -0700
[IRDA]: smsc-ircc2, smcinit support for ALi ISA bridges
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6: (78 commits)
commit e97b81ddbb
Author: Mark M. Hoffman <mhoffman@lightlink.com>
Date: Thu Mar 23 16:50:25 2006 +0100
[PATCH] i2c-parport: Make type parameter mandatory
This patch forces the user to specify what type of adapter is present when
loading i2c-parport or i2c-parport-light. If none is specified, the driver
init simply fails - instead of assuming adapter type 0.
This alleviates the sometimes lengthy boot time delays which can be caused
by accidentally building one of these into a kernel along with several i2c
slave drivers that have lengthy probe routines (e.g. hwmon drivers).
Kconfig and documentation updated accordingly.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
...
Documentation to describe asynchronous xfrm events to help people
writting HA code in user space.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This updates the DMA API documentation to address a few issues:
- The dma_map_sg() call results are used like pci_map_sg() results:
using sg_dma_address() and sg_dma_len(). That's not wholly obvious
to folk reading _only_ the "new" DMA-API.txt writeup.
- Buffers allocated by dma_alloc_coherent() may not be completely
free of coherency concerns ... some CPUs also have write buffers
that may need to be flushed.
- Cacheline coherence issues are now mentioned as being among issues
which affect dma buffers, and complicate/prevent using of static and
(especially) stack based buffers with the DMA calls.
I don't think many drivers currently need to worry about flushing write
buffers, but I did hit it with one SOC using external SDRAM for DMA
descriptors: without explicit writebuffer flushing, the on-chip DMA
controller accessed descriptors before the CPU completed the writes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch forces the user to specify what type of adapter is present when
loading i2c-parport or i2c-parport-light. If none is specified, the driver
init simply fails - instead of assuming adapter type 0.
This alleviates the sometimes lengthy boot time delays which can be caused
by accidentally building one of these into a kernel along with several i2c
slave drivers that have lengthy probe routines (e.g. hwmon drivers).
Kconfig and documentation updated accordingly.
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: fix typo in change count initialization
kconfig: recenter menuconfig
kconfig: revert conf behaviour change
kconfig: fix default value for choice input
kbuild: fix NULL dereference in scripts/mod/modpost.c
kbuild: fix mode of checkstack.pl and other files.
kbuild: rebuild initramfs if content of initramfs changes
kbuild: properly pass options to hostcc when doing make O=..
kbuild: modules_install for external modules must not remove existing modules
kbuild: fix make dir/
ver_linux: don't print reiser4progs version if none found
kbuild: mips: fix sed regexp to generate asm-offset.h
kbuild: fix building single targets with make O=.. single-target
kbuild: use relative path to -I
kbuild: fix unneeded rebuilds in drivers/net/chelsio after moving source tree
kbuild: fix unneeded rebuilds in drivers/media/video after moving source tree
kbuild: fix garbled text in modules.txt
* 'splice' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] vfs: add splice_write and splice_read to documentation
[PATCH] Remove sys_ prefix of new syscalls from __NR_sys_*
[PATCH] splice: warning fix
[PATCH] another round of fs/pipe.c cleanups
[PATCH] splice: comment styles
[PATCH] splice: add Ingo as addition copyright holder
[PATCH] splice: unlikely() optimizations
[PATCH] splice: speedups and optimizations
[PATCH] pipe.c/fifo.c code cleanups
[PATCH] get rid of the PIPE_*() macros
[PATCH] splice: speedup __generic_file_splice_read
[PATCH] splice: add direct fd <-> fd splicing support
[PATCH] splice: add optional input and output offsets
[PATCH] introduce a "kernel-internal pipe object" abstraction
[PATCH] splice: be smarter about calling do_page_cache_readahead()
[PATCH] splice: optimize the splice buffer mapping
[PATCH] splice: cleanup __generic_file_splice_read()
[PATCH] splice: only call wake_up_interruptible() when we really have to
[PATCH] splice: potential !page dereference
[PATCH] splice: mark the io page as accessed
