We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user sets the usb_request's no_interrupt, then there will be no
completion event for the request. Currently the driver incorrectly uses
the event status of a different request to report the status for a
request with no_interrupt. The dwc3 driver needs to check the TRB status
associated with the request when reporting its status.
Note: this is only applicable to missed_isoc TRB completion status, but
the other status are also listed for completeness/documentation.
Fixes: 6d8a019614 ("usb: dwc3: gadget: check for Missed Isoc from event status")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/db2c80108286cfd108adb05bad52138b78d7c3a7.1650673655.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.
Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.
Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).
Note: the current series only supports hubs connected directly to
a root hub, support for other configurations could be added if
needed.
Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220217104219.v21.2.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a "gadget" bus and uses it for registering gadgets and
their drivers. From now on, bindings will be managed by the driver
core rather than through ad-hoc manipulations in the UDC core.
As part of this change, the driver_pending_list is removed. The UDC
core won't need to keep track of unbound drivers for later binding,
because the driver core handles all of that for us.
However, we do need one new feature: a way to prevent gadget drivers
from being bound to more than one gadget at a time. The existing code
does this automatically, but the driver core doesn't -- it's perfectly
happy to bind a single driver to all the matching devices on the bus.
The patch adds a new bitflag to the usb_gadget_driver structure for
this purpose.
A nice side effect of this change is a reduction in the total lines of
code, since now the driver core will do part of the work that the UDC
used to do.
A possible future patch could add udc devices to the gadget bus, say
as a separate device type.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSpdxaDNeC2BBOf@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding a "gadget" bus, this patch reverses the
order of registration of udc and gadget devices in usb_add_gadget().
The current code adds the gadget device first, probably because that
was more convenient at the time and the order didn't really matter.
But with the upcoming change, adding the gadget will cause driver
probing to occur. Unwinding that on the error pathway will become
much more obtrusive, not to mention the fact that a gadget driver
might not work properly before the udc is registered. It's better to
register the udc device first, particularly since that doesn't involve
a bus or driver binding and therefore is simpler to unwind.
For symmetry, the order of unregistration in usb_del_gadget() is
likewise reversed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSo6fU1FlNq8cOZ@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for adding a "gadget" bus, this patch renames
usb_gadget_probe_driver() to usb_gadget_register_driver(). The new
name will be more accurate, since gadget drivers will be registered on
the gadget bus and the probing will be done by the driver core, not
the UDC core.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YmSc29YZvxgT5fEJ@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ON Semiconductor FSA4480 is a USB Type-C port multimedia switch with
support for analog audio headsets. It allows sharing a common USB Type-C
port to pass USB2.0 signal, analog audio, sideband use wires and analog
microphone signal.
Due to lacking upstream audio support for testing, the audio muxing is
left untouched, but implementation of muxing the SBU lines is provided
as a pair of Type-C mux and switch devices. This provides the necessary
support for enabling the DisplayPort altmode on devices with this
circuit.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422222351.1297276-8-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Qualcomm platforms the USB/DP PHY handles muxing and orientation
switching of the SuperSpeed lines, but the SBU lines needs to be
connected and switched by external (to the SoC) hardware.
It's therefor necessary to be able to have the TypeC controller operate
multiple TypeC muxes and switches. Use the newly introduced indirection
object to handle this, to avoid having to taint the TypeC controllers
with knowledge about the downstream hardware configuration.
The max number of devs per indirection is set to 3, which account for
being able to mux/switch the USB HS, SS and SBU lines, as per defined
defined in the usb-c-connector binding. This number could be grown if
need arrises at a later point in time.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422222351.1297276-6-bjorn.andersson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In error path of ucsi_init(), it will unregister all valid ucsi connectors,
and similar operation also happen in ucsi_unregister(),
add a common function ucsi_unregister_connectors() for two places,
inside this function, if con->wq is NULL, it will break the loop,
if other kind of error happen after con->wq allocated,
ucsi/typec related API is safe to unregister.
Also in ucsi_init(), it allocate number of (ucsi->cap.num_connectors + 1)
connectors, there is one extra as the ending,
ucsi_unregister_connectors() is safe to unregister all ucsi connectors
according ucsi->cap.num_connectors,
remove the extra one connector to save memory.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1650881886-25530-2-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes:
USB-serial fixes for 5.18-rc4
Here's a fix for a potential overflow issue in the whiteheat driver when
using the old ARM ABI.
Included are also some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: whiteheat: fix heap overflow in WHITEHEAT_GET_DTR_RTS
USB: serial: cp210x: add PIDs for Kamstrup USB Meter Reader
USB: serial: option: add support for Cinterion MV32-WA/MV32-WB
USB: serial: option: add Telit 0x1057, 0x1058, 0x1075 compositions
The documentation for the freeze() method says that it "should quiesce
the device so that it doesn't generate IRQs or DMA". The unspoken
consequence of not doing this is that MSIs aimed at non-boot CPUs may
get fully lost if they're sent during the period where the target CPU is
offline.
The current callbacks for USB HCD do not fully quiesce interrupts,
specifically on XHCI. Change to use the full suspend/resume flow for
freeze/thaw to ensure interrupts are fully quiesced. This fixes issues
where USB devices fail to thaw during hibernation because XHCI misses
its interrupt and cannot recover.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20220421103751.v3.2.I8226c7fdae88329ef70957b96a39b346c69a914e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PM_EVENT_FREEZE and PM_EVENT_QUIESCE messages should cause the
device to stop generating interrupts. USB core was previously allowing
devices that were already runtime suspended to keep remote wakeup
enabled if they had gone down that way. This violates the contract with
pm, and can potentially cause MSI interrupts to be lost.
Change that so that if a device is runtime suspended with remote wakeups
enabled, it will be resumed to ensure remote wakeup is always disabled
across a freeze.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20220421103751.v3.1.I2c636c4decc358f5e6c27b810748904cc69beada@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a deadlock in oxu_bus_suspend(), which is shown below:
(Thread 1) | (Thread 2)
| timer_action()
oxu_bus_suspend() | mod_timer()
spin_lock_irq() //(1) | (wait a time)
... | oxu_watchdog()
del_timer_sync() | spin_lock_irq() //(2)
(wait timer to stop) | ...
We hold oxu->lock in position (1) of thread 1, and use
del_timer_sync() to wait timer to stop, but timer handler
also need oxu->lock in position (2) of thread 2. As a result,
oxu_bus_suspend() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irq(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417120305.64577-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list_for_each_entry_safe() macro saves the current item (n) and
the item after (n+1), so that n can be safely removed without
corrupting the list. However, when traversing the list and removing
items using gadget giveback, the DWC3 lock is briefly released,
allowing other routines to execute. There is a situation where, while
items are being removed from the cancelled_list using
dwc3_gadget_ep_cleanup_cancelled_requests(), the pullup disable
routine is running in parallel (due to UDC unbind). As the cleanup
routine removes n, and the pullup disable removes n+1, once the
cleanup retakes the DWC3 lock, it references a request who was already
removed/handled. With list debug enabled, this leads to a panic.
Ensure all instances of the macro are replaced where gadget giveback
is used.
Example call stack:
Thread#1:
__dwc3_gadget_ep_set_halt() - CLEAR HALT
-> dwc3_gadget_ep_cleanup_cancelled_requests()
->list_for_each_entry_safe()
->dwc3_gadget_giveback(n)
->dwc3_gadget_del_and_unmap_request()- n deleted[cancelled_list]
->spin_unlock
->Thread#2 executes
...
->dwc3_gadget_giveback(n+1)
->Already removed!
Thread#2:
dwc3_gadget_pullup()
->waiting for dwc3 spin_lock
...
->Thread#1 released lock
->dwc3_stop_active_transfers()
->dwc3_remove_requests()
->fetches n+1 item from cancelled_list (n removed by Thread#1)
->dwc3_gadget_giveback()
->dwc3_gadget_del_and_unmap_request()- n+1 deleted[cancelled_list]
->spin_unlock
Fixes: d4f1afe5e8 ("usb: dwc3: gadget: move requests to cancelled_list")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414183521.23451-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_ep_clear_halt() API can be called from the function driver, and
translates to dwc3_gadget_ep_set_halt(). This routine is shared with when
the host issues a clear feature ENDPOINT_HALT, and is differentiated by the
protocol argument. If the following sequence occurs, there can be a
situation where the delayed_status flag is improperly cleared for the wrong
SETUP transaction:
1. Vendor specific control transfer returns USB_GADGET_DELAYED_STATUS.
2. DWC3 gadget sets dwc->delayed_status to '1'.
3. Another function driver issues a usb_ep_clear_halt() call.
4. DWC3 gadget issues dwc3_stop_active_transfer() and sets
DWC3_EP_PENDING_CLEAR_STALL.
5. EP command complete interrupt triggers for the end transfer, and
dwc3_ep0_send_delayed_status() is allowed to run, as delayed_status
is '1' due to step#1.
6. STATUS phase is sent, and delayed_status is cleared.
7. Vendor specific control transfer is finished being handled, and issues
usb_composite_setup_continue(). This results in queuing of a data
phase.
Cache the protocol flag so that DWC3 gadget is aware of when the clear halt
is due to a SETUP request from the host versus when it is sourced from a
function driver. This allows for the EP command complete interrupt to know
if it needs to issue a delayed status phase.
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414073902.21960-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any function like UVC is deactivating gadget as part of composition
switch which results in not calling pullup enablement, it is not getting
enabled after switch to new composition due to this deactivation flag
not cleared. This results in USB enumeration not happening after switch
to new USB composition. Hence clear deactivation flag inside gadget
structure in configfs_composite_unbind() before switch to new USB
composition.
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220413211038.72797-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add OTG support for the JZ4775 SoC, the JZ4780 SoC, the X1000 SoC,
the X1600 SoC, the X1700 SoC, the X1830 SoC, and the X2000 SoC
from Ingenic.
Introduce support for disable Ingenic overcurrent detection, once
selected, it enables the GOTGCTL register bits VbvalidOvEn and
VbvalidOvVal to disable the VBUS overcurrent detection.
This patch is derived from Dragan Čečavac (in the kernel 3.18.3
tree of CI20). It is very useful for the MIPS Creator CI20 (r1).
Without this patch, OTG port of CI20 has a great probability to
face overcurrent warning, which breaks the OTG functionality.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Dragan Čečavac <dragancecavac@yahoo.com>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/1649964337-114337-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver, OMAP1 specific, now omits clk_prepare/unprepare() steps, not
supported by OMAP1 custom implementation of clock API. However, non-CCF
stubs of those functions exist for use on such platforms until converted
to CCF.
Update the driver to be compatible with CCF implementation of clock API.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Link: https://lore.kernel.org/r/20220402112658.130191-1-jmkrzyszt@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two kerneldoc comments in gadget.c have excess function parameter description or wrong
prototype name and one kerneldoc comment in core.c has an excess function parameter
description, resulting in these three doc-build warnings:
1. ./drivers/usb/dwc3/gadget.c:675: warning: Excess function parameter
'nfifos' description in 'dwc3_gadget_calc_tx_fifo_size'
2. ./drivers/usb/dwc3/gadget.c:700: warning: expecting prototype for
dwc3_gadget_clear_tx_fifo_size(). Prototype was for dwc3_gadget_clear_tx_fifos()
instead
3. ./drivers/usb/dwc3/core.c:347: warning: Excess function parameter 'ref_clk_per'
description in 'dwc3_ref_clk_period'
Fix the warnings by correcting the prototype name and removing excess parameter descriptions.
Signed-off-by: Kushagra Verma <kushagra765@outlook.com>
Link: https://lore.kernel.org/r/SI2PR01MB392995043CACD80884A13764F81C9@SI2PR01MB3929.apcprd01.prod.exchangelabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
