[Why]
comparing pwm bl values (coverted) with user brightness(converted)
levels in commit_tail leads to continuous setting of backlight via dmub
as they don't to match.
This leads overdrive in queuing of commands to DMCU that sometimes lead
to depending on load on DMCU fw:
"[drm:dc_dmub_srv_wait_idle] *ERROR* Error waiting for DMUB idle: status=3"
[How]
Store last successfully set backlight value and compare with it instead
of pwm reads which is not what we should compare with.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
On resume we do link detection for all non-MST connectors.
MST is handled separately. However the condition for telling
if connector is on mst branch is not enough for mst hub case.
Link detection for mst branch link leads to mst topology reset.
That causes assert in dc_link_allocate_mst_payload()
[How]
Use link type as indicator for mst link.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When waking from low-power states, a DP sink may remain unresponsive to
AUX transactions.
[How]
Try to toggle DPCD SET_POWER register repeatedly (up to a maximum
timeout value) until DP sink becomes responsive.
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In init_hw() we call init_pipes() before enabling power gating.
init_pipes() tries to power gate dsc but it may fail because
required force-ons are not released yet.
As a result with dsc config the following errors observed on resume:
"REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control"
[How]
Move enable_power_gating_plane() before init_pipes() in init_hw()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC Power down code has been moved from dcn31_init_hw into init_pipes()
Need to remove it from dcn10_init_hw() as well to avoid duplicated action
on dcn1.x/2.x
[How]
Remove DSC power down code from dcn10_init_hw()
Fixes: 8fa6f4c571 ("drm/amd/display: fixed the DSC power off sequence during Driver PnP")
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Once DSC slice cannot fit pixel clock, we incorrectly
reset min slices to 0 and allow max slice to operate,
even when max slice itself cannot fit the pixel clock
properly.
[How]
Change the sequence such that we correctly determine
DSC is not possible when both min slices and max
slices cannot fit pixel clock per slice.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some video card has more than one vcn instance, passing 0 to
vcn_v3_0_pause_dpg_mode is incorrect.
Error msg:
Register(1) [mmUVD_POWER_STATUS] failed to reach value
0x00000001 != 0x00000002
Reviewed-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: tiancyin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
For VCN FW to detect ASIC type, in order to use different mailbox registers.
V2: simplify codes and fix format issue.
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Acked-by Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMU takes clock limits in Mhz units. socclk and fclk were
using 10 khz units in some cases. Switch to Mhz units.
Fixes higher than required SoC clocks.
Fixes: 97cf32996c ("drm/amd/pm: Removed fixed clock in auto mode DPM")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Make dcn315 base its clock table off dcfclk rather than fclk.
This change also adds some sanity checking to make sure an
empty pmfw table does not result in invalid dal clocks.
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Variable igp_lane_info always is 0. 0 & any value = 0 and false.
In this way, all сonditional statements will false.
The code was leftover from when the code was ported from radeon
where igp_lane_info was derived from the vbios on supported
platforms.
[update commit message - Alex]
Signed-off-by: Grigory Vasilyev <h0tc0d3@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- [FW Promotion] Release 0.0.111.0
- Check for invalid input params when building scaling params
- Move link_trace for edp to dp_trace
- Fix missing-prototypes warning
- Enable 3 plane for DCN 3.0 and 3.02
- Extract set stream attribute into link_hwss
- Revert Power down hardware if timer not trigger
- Add support for handling 128b/132b link training test request
- Add configuration options for AUX wake work around
- Remove underflow IRQ type
- Add flip interval workaround for low FPS in some game
- Remove assert for odm transition case
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP2.x added new enum values for UHBR link rates in link training test
request for test automation. We need to add UHBR link rates test request
support in preparation for compliance test automation.
[how]
added a function that translate test link rate to dc link rate. Call
the translation function to decide the requested test link rate.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Work around to try to wake unresponsive DP sinks may need to be adjusted
for certain sinks.
[How]
Add options to disable work around or adjust time spent trying to wake
unresponsive DPRX.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some games experience low FPS issues when FreeSync is on and VSync is
toggled to half refresh rate.
[HOW]
First create a function to determine workaround conditions, which is
when we detect 2 or more VSync interrupts between flips and a very short
VSync to flip interval. We do the workaround during VSync interrupts and
set the v_total_max and min to nominal. We also cleanup after we exit
the game.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Angus Wang <Angus.Wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For VG20 + XGMI bridge, all mappings PTEs cache in TC, this may have
stall invalid PTEs in TC because one cache line has 8 pages. Need always
flush_tlb after updating mapping.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the kernel test robot warning below:
drivers/gpu/drm/amd/amdgpu/../display/dmub/inc/dmub_cmd.h:2893:12:
warning: variable 'temp' set but not used [-Wunused-but-set-variable]
Replaced the assignment to the unused temp variable with READ_ONCE()
macro to flush the writes. READ_ONCE() helps avoid the use of
volatile and makes it obvious from the code that the read here is
intentional. Also verified on x86 that the generated code is exactly the
same as before.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Aashish Sharma <shraash@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMI clock measure API is failing on NAVI12, because
sysfs node for pp_dpm_vclk is not existing. Enable
sysfs node for pp_dpm_vclk for NAVI12.
v2: Also enable sysfs node for pp_dpm_dclk.
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Marko Zekovic <Marko.Zekovic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Testing the valid bit is not enough to figure out if we
need to invalidate the TLB or not.
During eviction it is quite likely that we move a BO from VRAM to GTT and
update the page tables immediately to the new GTT address.
Rework the whole function to get all the necessary parameters directly as
value.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since unique_id is only supported in PMFW 0x3A5300 and higher, we will
only be able to use it inside Smu_Metrics_V3_t, which requires PMFW
0x3A4900 and higher. Remove the unique_id/serial_number references from
the v1 and v2 tables to avoid any confusion, and return 0 if metrics_v1
or metrics_v2 are used to try to get the unique_id/serial_number.
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FPU documentation states that developers must not use DC_FP_START/END
inside dml files, but use this macro to wrap calls to FPU functions in
dc folder (outside dml folder). Therefore, this patch removes DC_FP_*
wrappers from dml folder and wraps calls for these FPU operations
outside dml, as required.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn10_validate_bandwidth is only used on dcn10 files, but is declared in
dcn_calcs files. Rename dcn10_* to dcn_* in calcs, remove DC_FP_* wrapper
inside DML folder and create an specific dcn10_validate_bandwidth in
dcn10_resources that calls dcn_validate_bandwidth and properly wraps that
FPU function with DC_FP_* macro.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is being added to SMU Metrics, so add the required tie-ins in the
kernel. Also create the corresponding unique_id sysfs file.
v2: Add FW version check, remove SMU mutex
v3: Fix style warning
v4: Add MP1 IP_VERSION check to FW version check
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To ease readability, use switch to set unique_id as supported for the
supported IP_VERSIONs, and set it to unsupported by default for all
other ASICs.
This makes it easier to add IP_VERSIONs later on, and makes it obvious
that it is not supported by default, instead of the current logic that
assumes that it is supported unless it is not one of the specified
IP_VERSIONs.
v2: Rebase onto previous IP_VERSION change
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Kevin Wang <KevinYang.Wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
