In commit 482812d566 ("drm/amd/display: Set max TTU on
DPG enable"), "hubp.h" was added which caused the duplicate include.
To be on the safe side, remove the later duplicate include.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our driver supports overlay planes, and as expected, some userspace
compositor takes advantage of these features. If the userspace is not
enabling the cursor, they can use multiple planes as they please.
Nevertheless, we start to have constraints when userspace tries to
enable hardware cursor with various planes. Basically, we cannot draw
the cursor at the same size and position on two separated pipes since it
uses extra bandwidth and DML only run with one cursor.
For those reasons, when we enable hardware cursor and multiple planes,
our driver should accept variations like the ones described below:
+-------------+ +--------------+
| +---------+ | | |
| |Primary | | | Primary |
| | | | | Overlay |
| +---------+ | | |
|Overlay | | |
+-------------+ +--------------+
In this scenario, we can have the desktop UI in the overlay and some
other framebuffer attached to the primary plane (e.g., video). However,
userspace needs to obey some rules and avoid scenarios like the ones
described below (when enabling hw cursor):
+--------+
|Overlay |
+-------------+ +-----+-------+ +-| |--+
| +--------+ | +--------+ | | +--------+ |
| |Overlay | | |Overlay | | | |
| | | | | | | | |
| +--------+ | +--------+ | | |
| Primary | | Primary | | Primary |
+-------------+ +-------------+ +-------------+
+-------------+ +-------------+
| +--------+ | Primary |
| |Overlay | | |
| | | | |
| +--------+ | +--------+ |
| Primary | | |Overlay | |
+-------------+ +-| |--+
+--------+
If the userspace violates some of the above scenarios, our driver needs
to reject the commit; otherwise, we can have unexpected behavior. Since
we don't have a proper driver validation for the above case, we can see
some problems like a duplicate cursor in applications that use multiple
planes. This commit fixes the cursor issue and others by adding adequate
verification for multiple planes.
Change since V1 (Harry and Sean):
- Remove cursor verification from the equation.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following build warnings.
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:
In function ‘dm_update_mst_vcpi_slots_for_dsc’:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:6242:46:
warning: variable ‘old_con_state’ set but not used
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:
In function ‘amdgpu_dm_commit_cursors’:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:7709:44:
warning: variable ‘new_plane_state’ set but not used
The variables were introduced to be used in iterators, but not used.
Use other iterators which don't require the unused variables.
Fixes: 8ad278062d ("drm/amd/display: Disable cursors before disabling planes")
Fixes: 29b9ba74f6 ("drm/amd/display: Recalculate VCPI slots for new DSC connectors")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Was missing when this structure was updated.
Fixes: 46a83eba27 ("drm/amd/display: Add debugfs to control DMUB trace buffer events")
Reviewed-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-fixes-5.13-2021-05-05:
amdgpu:
- MPO hang workaround
- Fix for concurrent VM flushes on vega/navi
- dcefclk is not adjustable on navi1x and newer
- MST HPD debugfs fix
- Suspend/resumes fixes
- Register VGA clients late in case driver fails to load
- Fix GEM leak in user framebuffer create
- Add support for polaris12 with 32 bit memory interface
- Fix duplicate cursor issue when using overlay
- Fix corruption with tiled surfaces on VCN3
- Add BO size and stride check to fix BO size verification
radeon:
- Fix off-by-one in power state parsing
- Fix possible memory leak in power state parsing
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210506033929.3875-1-alexander.deucher@amd.com
Our driver supports overlay planes, and as expected, some userspace
compositor takes advantage of these features. If the userspace is not
enabling the cursor, they can use multiple planes as they please.
Nevertheless, we start to have constraints when userspace tries to
enable hardware cursor with various planes. Basically, we cannot draw
the cursor at the same size and position on two separated pipes since it
uses extra bandwidth and DML only run with one cursor.
For those reasons, when we enable hardware cursor and multiple planes,
our driver should accept variations like the ones described below:
+-------------+ +--------------+
| +---------+ | | |
| |Primary | | | Primary |
| | | | | Overlay |
| +---------+ | | |
|Overlay | | |
+-------------+ +--------------+
In this scenario, we can have the desktop UI in the overlay and some
other framebuffer attached to the primary plane (e.g., video). However,
userspace needs to obey some rules and avoid scenarios like the ones
described below (when enabling hw cursor):
+--------+
|Overlay |
+-------------+ +-----+-------+ +-| |--+
| +--------+ | +--------+ | | +--------+ |
| |Overlay | | |Overlay | | | |
| | | | | | | | |
| +--------+ | +--------+ | | |
| Primary | | Primary | | Primary |
+-------------+ +-------------+ +-------------+
+-------------+ +-------------+
| +--------+ | Primary |
| |Overlay | | |
| | | | |
| +--------+ | +--------+ |
| Primary | | |Overlay | |
+-------------+ +-| |--+
+--------+
If the userspace violates some of the above scenarios, our driver needs
to reject the commit; otherwise, we can have unexpected behavior. Since
we don't have a proper driver validation for the above case, we can see
some problems like a duplicate cursor in applications that use multiple
planes. This commit fixes the cursor issue and others by adding adequate
verification for multiple planes.
Change since V1 (Harry and Sean):
- Remove cursor verification from the equation.
Cc: Louis Li <Ching-shih.Li@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DP 1.4a spec mandates that if DP_EXTENDED_RECEIVER_CAP_FIELD_PRESENT is
set, Extended Base Receiver Capability DPCD space must be used. Without
doing that, the three DPCD values that differ will be wrong, leading to
incorrect or limited functionality. MST link rate, for example, could
have a lower value. Also, Synaptics quirk wouldn't work out well when
Extended DPCD was not read, resulting in no DSC for such hubs.
[how]
Modify MST topology manager to use the values from Extended DPCD where
applicable.
To prevent regression on the sources that have a lower maximum link rate
capability than MAX_LINK_RATE from Extended DPCD, have the drivers
supply maximum lane count and rate at initialization time.
This also reverts commit 2dcab875e7 ("Revert drm/dp_mst: Retrieve
extended DPCD caps for topology manager"), brining the change back to the
original commit ad44c03208 ("drm/dp_mst: Retrieve extended DPCD caps for
topology manager").
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210429221151.22020-2-nikola.cornij@amd.com
[why]
Previous statement would always evaluate to true
making it meaningless
[how]
Just check if a connector is MST by checking if its port exists.
Fixes: 41efcd3879 ("drm/amd/display: Add MST capability to trigger_hotplug interface")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As hardware team suggested that we need to add a max dsc bw overhead
into existing stream bandwidth when DSC is used.
The formula as below:
max_dsc_bw_overhead =
v_addressable * slice_count * 256 bit * pixel clock / v_total / h_total
effective stream bandwidth = pixel clock * bpp
stream bandwidth = effective stream bandwidth + dsc stream overhead
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add a per-connector debugfs entry to expose internal display flag,
which is indication that the display is "internally connected"
and not hotpluggable.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver program dpp clock calculate by pipe split config but hw config is single pipe.
[How]
Skip programming clock when allow seamless boot.
After porgramming pipe config, seamless boot flag will be clear.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change only fix dpp clock switch to lower case.
New solution later can fix both case, which is "dc: skip
program clock when allow seamless boot"
[How]
This reverts commit "dc: wait vblank when stream enabled
and update dpp clock"
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is something that we've wanted for a while now: the ability to
actually look up the respective drm_device for a given drm_dp_aux struct.
This will also allow us to transition over to using the drm_dbg_*() helpers
for debug message printing, as we'll finally have a drm_device to reference
for doing so.
Note that there is one limitation with this - because some DP AUX adapters
exist as platform devices which are initialized independently of their
respective DRM devices, one cannot rely on drm_dp_aux->drm_dev to always be
non-NULL until drm_dp_aux_register() has been called. We make sure to point
this out in the documentation for struct drm_dp_aux.
v3:
* Add WARN_ON_ONCE() to drm_dp_aux_register() if drm_dev isn't filled out
Signed-off-by: Lyude Paul <lyude@redhat.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210423184309.207645-4-lyude@redhat.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
In dm_dp_mst_detect(), We should check whether or not @connector
has been unregistered from userspace. If the connector is unregistered,
we should return disconnected status.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: Yingjie Wang <wangyingjie55@126.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some MST devices uses different method to enable mst
specific stream features.
[How]
Add dm_helpers_mst_enable_stream features. This can be
modified later when we are ready to implement those features.
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why?]
When a monitor does not set both QS and QY bits, DC does not
set Q0, Q1, QY0 and QY1 bits in AVI infoframe. Setting RGB bits
should be separate from setting YCC bits.
[How?]
Separate logic for setting RGB and YCC quantization range bits
in the AVI infoframe.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Requirement from the spec - we shouldn't be potentially exiting out
early based on encryption status.
[How]
Drop the calls from HDCP1 and HDCP2 execution that exit out early
based on link encryption status.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
While Link Training is being performed,
and the LTTPRs are in Non-LTTPR or LTTPR Transparent mode,
any DPCD registers besides those used for Link Training are not to be
accessed.
The spec defines the link training registers as DP_TRAINING_PATTERN_SET
(102h) to DP_TRAINING_LANE3_SET (106h), and DP_LANE0_1_STATUS (202h)
to DP_ADJUST_REQUEST_LANE2_3 (207h).
[HOW]
Move the current write to DPCD Address DP_LINK_TRAINING_PATTERN_SET out
of its conditional block.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We should skip programming manual trigger on non-primary planes when MPO is
enabled.
[HOW]
Implement an explicit mechanism for skipping manual trigger programming
for planes that shouldn't cause the frame to end.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previous change had been reverted since it caused hang.
Remake change to avoid defect.
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating.
Add additional delay time for single rank dimm.
Fixes: b8720ed0b8 ("drm/amd/display: System black screen hangs on driver load")
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
the current implementation of hdcp2 rx id list validation does not
have handler/checker for invalid message status, e.g. HMAC, the V
parameter calculated from PSP not matching the V prime from Rx.
[how]
return a generic FAILURE for any message status not SUCCESS or
REVOKED.
Signed-off-by: Dingchen (David) Zhang <dingchen.zhang@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
currently we enforce to update hdcp display using TYPE0, but there
is case that connector CP type prop be TYPE1 instead of type0.
[how]
using the drm prop of CP type of the connector as input argument.
Signed-off-by: Dingchen (David) Zhang <dingchen.zhang@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
We want to immediately fail seamless boot validation if DSC is active,
as VBIOS currently does not support DSC timings. Add a check for
the relevant flag in dc_validate_seamless_boot_timing.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch checks the return value of the function
dc_link_add_remote_sink before using it. This was causing
a crash during consecutive hotplugs of DP MST displays.
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 55fa622fe6.
The regression caused by the original patch has been
cleared, thus introduce back the change.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
