Qualcomm DTS fixe for 5.19
The pinctrl state was lost in the recent refactoring of the MSM8974
Devicetree, this contains a fix for this.
* tag 'qcom-dts-fixes-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974: re-add missing pinctrl
Link: https://lore.kernel.org/r/20220713030627.1371156-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX fixes for 5.19, round 3:
- Fix GPIO property for imx6qdl-ts7970 board.
- Fix touchscreen pinctrl for imx6ull-colibri board by moving iomuxc-snvs
pin to the correct controller device.
- Fix SFP node of fsl-ls1028a to have a required clock property.
* tag 'imx-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: colibri-imx6ull: fix snvs pinmux group
ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
arm64: dts: ls1028a: Update SFP node to include clock
Link: https://lore.kernel.org/r/20220709032716.GA9868@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix SPI NOR compatible on Orange Pi Zero
* tag 'sunxi-fixes-for-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
Link: https://lore.kernel.org/r/Ysh44qUmdmF6TWS6@kista.localdomain
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AT91 fixes for 5.19 #2
It contains 2 DT fixes:
- one for SAMA5D2 to fix the i2s1 assigned-clock-parents property
- one for kswitch-d10 (LAN966 based) enforcing proper settings
on GPIO pins
* tag 'at91-fixes-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2: Fix typo in i2s1 node
ARM: dts: kswitch-d10: use open drain mode for coma-mode pins
Link: https://lore.kernel.org/r/20220708151621.860339-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A pin controlled by the iomuxc-snvs pin controller must be
specified under the dtb's iomuxc-snvs node.
Move the one and only pin of that category from the iomuxc node
and set the pinctrl-0 using it accordingly.
Fixes: 2aa9d62019 ("ARM: dts: imx6ull-colibri: add touchscreen device nodes")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
STM32 DT fixes for v5.19, round 2
Highlights:
-----------
-Fixes STM32MP15:
- Add missing usbh clock and fix clk order for usbh to avoid PLL
issue.
- Fix SCMI version: use scmi regulator and update missing SCMI
clocks to be able to correcly boot.
* tag 'stm32-dt-for-v5.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add missing usbh clock and fix clk order on stm32mp15
ARM: dts: stm32: delete fixed clock node on STM32MP15-SCMI
ARM: dts: stm32: DSI should use LSE SCMI clock on DK1/ED1 STM32 board
ARM: dts: stm32: use the correct clock source for CEC on stm32mp151
ARM: dts: stm32: fix pwr regulators references to use scmi
Link: https://lore.kernel.org/r/1259e082-a3a4-96a5-ec9c-05dbb893a746@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The USBH composed of EHCI and OHCI controllers needs the PHY clock to be
initialized first, before enabling (gating) them. The reverse is also
required when going to suspend.
So, add USBPHY clock as 1st entry in both controllers, so the USBPHY PLL
gets enabled 1st upon controller init. Upon suspend/resume, this also makes
the clock to be disabled/re-enabled in the correct order.
This fixes some IRQ storm conditions seen when going to low-power, due to
PHY PLL being disabled before all clocks are cleanly gated.
Fixes: 949a0c0dec ("ARM: dts: stm32: add USB Host (USBH) support to stm32mp157c")
Fixes: db7be2cb87 ("ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
i.MX fixes for 5.19, round 2:
- Fix the SDIO description for imx7d-smegw01 board to ensure there is
no communication made at 1.8V.
- Fix pgc_ispdwp power-domain clock, which should be
IMX8MP_CLK_MEDIA_ISP_ROOT.
- Re-enable framebuffer support in mxs_defconfig to fix a Kconfig
regression.
- A series from Peng Fan (and Sherry Sun) fixing various pads on i.MX8MP
based boards to leave reserved bits untouched.
* tag 'imx-fixes-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mp-icore-mx8mp-edim2.2: correct pad settings
arm64: dts: imx8mp-phyboard-pollux-rdk: correct i2c2 & mmc settings
arm64: dts: imx8mp-phyboard-pollux-rdk: correct eqos pad settings
arm64: dts: imx8mp-phyboard-pollux-rdk: correct uart pad settings
arm64: dts: imx8mp-venice-gw74xx: correct pad settings
arm64: dts: imx8mp-evk: correct I2C3 pad settings
arm64: dts: imx8mp-evk: correct I2C1 pad settings
arm64: dts: imx8mp-evk: correct I2C5 pad settings
arm64: dts: imx8mp-evk: correct vbus pad settings
arm64: dts: imx8mp-evk: correct eqos pad settings
arm64: dts: imx8mp-evk: correct vbus pad settings
arm64: dts: imx8mp-evk: correct gpio-led pad settings
arm64: dts: imx8mp-evk: correct the uart2 pinctl value
arm64: dts: imx8mp-evk: correct mmc pad settings
ARM: mxs_defconfig: Enable the framebuffer
arm64: dts: imx8mp: correct clock of pgc_ispdwp
ARM: dts: imx7d-smegw01: Fix the SDIO description
Link: https://lore.kernel.org/r/20220629021244.GL819983@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
AT91 fixes for 5.19
It contains 3 SoC fixes and 2 DT fixes:
SoC:
- fix the wakeup from RTC and RTT for ULP1 mode
- fix section mismatch warning
- fix SAM9X60 SiP detection
DT:
- fixes the EEPROMs compatibles for sama5d2_icp and sam9x60ek and EEPROM
size for sam9x60ek
* tag 'at91-fixes-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: at91: pm: Mark at91_pm_secure_init as __init
ARM: at91: fix soc detection for SAM9X60 SiPs
ARM: dts: at91: sama5d2_icp: fix eeprom compatibles
ARM: dts: at91: sam9x60ek: fix eeprom compatible and size
ARM: at91: pm: use proper compatibles for sama7g5's rtc and rtt
ARM: at91: pm: use proper compatibles for sam9x60's rtc and rtt
ARM: at91: pm: use proper compatible for sama5d2's rtc
Link: https://lore.kernel.org/r/20220628135130.3114878-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull ARM SoC fixes from Arnd Bergmann:
"A number of fixes have accumulated, but they are largely for harmless
issues:
- Several OF node leak fixes
- A fix to the Exynos7885 UART clock description
- DTS fixes to prevent boot failures on TI AM64 and J721s2
- Bus probe error handling fixes for Baikal-T1
- A fixup to the way STM32 SoCs use separate dts files for different
firmware stacks
- Multiple code fixes for Arm SCMI firmware, all dealing with
robustness of the implementation
- Multiple NXP i.MX devicetree fixes, addressing incorrect data in DT
nodes
- Three updates to the MAINTAINERS file, including Florian Fainelli
taking over BCM283x/BCM2711 (Raspberry Pi) from Nicolas Saenz
Julienne"
* tag 'soc-fixes-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
ARM: dts: aspeed: nuvia: rename vendor nuvia to qcom
arm: mach-spear: Add missing of_node_put() in time.c
ARM: cns3xxx: Fix refcount leak in cns3xxx_init
MAINTAINERS: Update email address
arm64: dts: ti: k3-am64-main: Remove support for HS400 speed mode
arm64: dts: ti: k3-j721s2: Fix overlapping GICD memory region
ARM: dts: bcm2711-rpi-400: Fix GPIO line names
bus: bt1-axi: Don't print error on -EPROBE_DEFER
bus: bt1-apb: Don't print error on -EPROBE_DEFER
ARM: Fix refcount leak in axxia_boot_secondary
ARM: dts: stm32: move SCMI related nodes in a dedicated file for stm32mp15
soc: imx: imx8m-blk-ctrl: fix display clock for LCDIF2 power domain
ARM: dts: imx6qdl-colibri: Fix capacitive touch reset polarity
ARM: dts: imx6qdl: correct PU regulator ramp delay
firmware: arm_scmi: Fix incorrect error propagation in scmi_voltage_descriptors_get
firmware: arm_scmi: Avoid using extended string-buffers sizes if not necessary
firmware: arm_scmi: Fix SENSOR_AXIS_NAME_GET behaviour when unsupported
ARM: dts: imx7: Move hsic_phy power domain to HSIC PHY node
soc: bcm: brcmstb: pm: pm-arm: Fix refcount leak in brcmstb_pm_probe
MAINTAINERS: Update BCM2711/BCM2835 maintainer
...
usdhc2 is connected to a Wifi chip that is powered by a 3.3V supply.
Pass the "no-1-8-v" property to guarantee that no communication is
made at 1.8V.
While at it, also remove the unnecessary properties: "cap-sd-highspeed",
"sd-uhs-ddr50", and "mmc-ddr-1_8v".
Fixes: 9ac0ae97e3 ("ARM: dts: imx7d-smegw01: Add support for i.MX7D SMEGW01 board")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO expander line names has been fixed in the vendor tree last year,
so upstream these changes.
Fixes: 1c701accec ("ARM: dts: Add Raspberry Pi 400 support")
Reported-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Adding a "secure" version of STM32 boards (DK1/DK2/ED1/EV1), SCMI (clock/
reset) protocol and OP-TEE node have been added in SoC dtsi file
(stm32mp151.dtsi). They have been added with a status disabled in order to
keep our legacy unchanged. It is actually not enough to keep our legacy
unchanged.
First, just a reminder about our use case: TF-A (BL2) loads and starts
OP-TEE, then loads and runs U-Boot. U-Boot code checks if an OP-TEE is
running, if yes it searches in Kernel device tree if an OP-TEE node is
present:
-If the OP-TEE node is not present then U-Boot copies OP-TEE node and its
reserved memory region from U-Boot device tree to the kernel device tree.
-If the OP-TEE node is present then it does nothing (this OP-TEE node will
be used by Linux). So U-Boot lets the kernel device tree unchanged thinking
it is correct for an OP-TEE usage. It is the case for our legacy boards,
the OP-TEE node is present (although disabled) but the reserved memory
region is not declared. As no memory region has been reserved for OP-TEE,
the end of DDR is seen by the kernel as free and then used for CMA. But as
OP-TEE is running, this end of DDR is already used by OP-TEE. So as soon as
kernel tries to access to the CMA region OP-TEE raises an error.
To fix it, all OP-TEE node and SCMI is moved in a dedicated file.
Fixes: 40b4157dbd ("ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15")
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: https://lore.kernel.org/r/20220613071920.5463-1-alexandre.torgue@foss.st.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The commit feedaacdad ("Input: atmel_mxt_ts - fix up inverted RESET
handler") requires the reset GPIO to have GPIO_ACTIVE_LOW.
Fixes: 1524b27c94 ("ARM: dts: imx6dl-colibri: Move common nodes to SoM dtsi")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 40130d327f ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the power domain to its actual user. This keeps the power domain
enabled even when the USB host is runtime suspended. This is necessary
to detect any downstream events, like device attach.
Fixes: 02f8eb40ef ("ARM: dts: imx7s: Add power domain for imx7d HSIC")
Suggested-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Pull more ARM SoC updates from Arnd Bergmann:
"This is the second part of the general SoC updates, containing
everything that did not make it in the initial pull request, or that
came in as a bugfix later.
- Devicetree updates for SoCFPGA, ASPEED, AT91 and Rockchip,
including a new machine using an ASPEED BMC.
- More DT fixes from Krzysztof Kozlowski across platforms
- A new SoC platform for the GXP baseboard management controller,
used in current server products from HPE"
* tag 'arm-late-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (56 commits)
ARM: configs: Enable more audio support for i.MX
tee: optee: Pass a pointer to virt_addr_valid()
arm64: dts: rockchip: rename Quartz64-A bluetooth gpios
arm64: dts: rockchip: add clocks property to cru node rk3368
arm64: dts: rockchip: add clocks property to cru node rk3308
arm64: dts: rockchip: add clocks to rk356x cru
ARM: dts: rockchip: add clocks property to cru node rk3228
ARM: dts: rockchip: add clocks property to cru node rk3036
ARM: dts: rockchip: add clocks property to cru node rk3066a/rk3188
ARM: dts: rockchip: add clocks property to cru node rk3288
ARM: dts: rockchip: Remove "amba" bus nodes from rv1108
ARM: dts: rockchip: add clocks property to cru node rv1108
arm64: dts: sprd: use new 'dma-channels' property
ARM: dts: da850: use new 'dma-channels' property
ARM: dts: pxa: use new 'dma-channels/requests' properties
soc: ixp4xx/qmgr: Fix unused match warning
ARM: ep93xx: Make ts72xx_register_flash() static
ARM: configs: enable support for Kontron KSwitch D10
ep93xx: clock: Do not return the address of the freed memory
arm64: dts: intel: add device tree for n6000
...
SoCFPGA dts updates for v5.19
- dtschema fix SPI NOR node
- correct dt-bindings doc for Altera gpio driver
- add support for n6000 Agilex platform and dt-bindings documentation
* tag 'socfpga_dts_updates_for_v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: intel: add device tree for n6000
dt-bindings: intel: add binding for Intel n6000
dt-bindings: soc: add bindings for Intel HPS Copy Engine
dt-bindings: gpio: altera: correct interrupt-cells
ARM: dts: socfpga: align SPI NOR node name with dtschema
Link: https://lore.kernel.org/r/20220519232317.16079-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The "amba" bus nodes wrapping all the DMA-330 nodes serve no useful
purpose, and certainly bear no relation at all to the actual underlying
interconnect topology. They appear to be cargo-cult copying from a
design misstep in the very early days of FDT adoption on ARM, which was
righted with the "arm,primecell" compatible, and the last trace of the
idea finally purged by commit 2ef7d5f342 ("ARM, ARM64: dts: drop
"arm,amba-bus" in favor of "simple-bus"").
As such, they can simply be removed and the DMA-330 nodes fitted into
the normal sort order.
The node names should be generic, so rename it to "dma-controller".
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20220330131608.30040-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
AT91 DT #2 for 5.19:
- at91: more DT compliance updates for RTC and RTT nodes
- at91: sama7g5: add microphone support
* tag 'at91-dt-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama7g5ek: add node for PDMC0
ARM: dts: at91: sama7g5: add nodes for PDMC
ARM: dts: at91: Use the generic "rtc" node name for the rtt IPs
ARM: dts: at91: Add the required 'atmel, rtt-rtc-time-reg' property
Link: https://lore.kernel.org/r/20220517153252.92393-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Patch series from Nick Hawkins:
"The GXP is the HPE BMC SoC that is used in the majority of HPE current
generation servers. Traditionally the asic will last multiple
generations of server before being replaced.
Info about SoC:
HPE GXP is the name of the HPE Soc. This SoC is used to implement many
BMC features at HPE. It supports ARMv7 architecture based on the Cortex
A9 core. It is capable of using an AXI bus to which a memory controller
is attached. It has multiple SPI interfaces to connect boot flash and
BIOS flash. It uses a 10/100/1000 MAC for network connectivity. It has
multiple i2c engines to drive connectivity with a host infrastructure.
The initial patches enable the watchdog and timer enabling the host to
be able to boot."
* hpe/gxp-soc:
MAINTAINERS: Introduce HPE GXP Architecture
ARM: dts: Introduce HPE GXP Device tree
dt-bindings: arm: hpe: add GXP Support
dt-bindings: timer: hpe,gxp-timer: Add HPE GXP Timer and Watchdog
clocksource/drivers/timer-gxp: Add HPE GXP Timer
watchdog: hpe-wdt: Introduce HPE GXP Watchdog
ARM: configs: multi_v7_defconfig: Add HPE GXP ARCH
ARM: hpe: Introduce the HPE GXP architecture
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull Kbuild updates from Masahiro Yamada:
- Add HOSTPKG_CONFIG env variable to allow users to override pkg-config
- Support W=e as a shorthand for KCFLAGS=-Werror
- Fix CONFIG_IKHEADERS build to support toybox cpio
- Add scripts/dummy-tools/pahole to ease distro packagers' life
- Suppress false-positive warnings from checksyscalls.sh for W=2 build
- Factor out the common code of arch/*/boot/install.sh into
scripts/install.sh
- Support 'kernel-install' tool in scripts/prune-kernel
- Refactor module-versioning to link the symbol versions at the final
link of vmlinux and modules
- Remove CONFIG_MODULE_REL_CRCS because module-versioning now works in
an arch-agnostic way
- Refactor modpost, Makefiles
* tag 'kbuild-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (56 commits)
genksyms: adjust the output format to modpost
kbuild: stop merging *.symversions
kbuild: link symbol CRCs at final link, removing CONFIG_MODULE_REL_CRCS
modpost: extract symbol versions from *.cmd files
modpost: add sym_find_with_module() helper
modpost: change the license of EXPORT_SYMBOL to bool type
modpost: remove left-over cross_compile declaration
kbuild: record symbol versions in *.cmd files
kbuild: generate a list of objects in vmlinux
modpost: move *.mod.c generation to write_mod_c_files()
modpost: merge add_{intree_flag,retpoline,staging_flag} to add_header
scripts/prune-kernel: Use kernel-install if available
kbuild: factor out the common installation code into scripts/install.sh
modpost: split new_symbol() to symbol allocation and hash table addition
modpost: make sym_add_exported() always allocate a new symbol
modpost: make multiple export error
modpost: dump Module.symvers in the same order of modules.order
modpost: traverse the namespace_list in order
modpost: use doubly linked list for dump_lists
modpost: traverse unresolved symbols in order
...
Pull ARMv4T/v5 multiplatform support from Arnd Bergmann:
"This series has been 12 years in the making, it mostly finishes the
work that was started with the founding of Linaro to clean up platform
support in the kernel.
The largest change here is a cleanup of the omap1 platform, which is
the final ARM machine type to get converted to the common-clk
subsystem. All the omap1 specific drivers are now made independent of
the mach/*.h headers to allow the platform to be part of a generic
ARMv4/v5 multiplatform kernel.
The last bit that enables this support is still missing here while we
wait for some last dependencies to make it into the mainline kernel
through other subsystems.
The s3c24xx, ixp4xx, iop32x, ep93xx and dove platforms were all almost
at the point of allowing multiplatform kernels, this work gets
completed here along with a few additional cleanup. At the same time,
the s3c24xx and s3c64xx are now deprecated and expected to get removed
in the future.
The PXA and OMAP1 bits are in a separate branch because of
dependencies. Once both branches are merged, only the three Intel
StrongARM platforms (RiscPC, Footbridge/NetWinder and StrongARM1100)
need separate kernels, and there are no plans to include these"
* tag 'arm-multiplatform-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: ixp4xx: Consolidate Kconfig fixing issue
ARM: versatile: Add missing of_node_put in dcscb_init
ARM: config: Refresh IXP4xx config after multiplatform
ARM: omap1: add back omap_set_dma_priority() stub
ARM: omap: fix missing declaration warnings
ARM: omap: fix address space warnings from sparse
ARM: spear: remove include/mach/ subdirectory
ARM: davinci: remove include/mach/ subdirectory
ARM: omap2: remove include/mach/ subdirectory
integrator: remove empty ap_init_early()
ARM: s3c: fix include path
MAINTAINERS: omap1: Add Janusz as an additional maintainer
ARM: omap1: htc_herald: fix typos in comments
ARM: OMAP1: fix typos in comments
ARM: OMAP1: clock: Remove noop code
ARM: OMAP1: clock: Remove unused code
ARM: OMAP1: clock: Fix UART rate reporting algorithm
ARM: OMAP1: clock: Fix early UART rate issues
ARM: OMAP1: Prepare for conversion of OMAP1 clocks to CCF
ARM: omap1: fix build with no SoC selected
...
Pull ARM DT updates from Arnd Bergmann:
"There are 40 branches this time, adding a lot of new hardware support,
and cleanups. Krzysztof Kozlowski continues his treewide cleanups.
There are a number of new SoCs, all of them as part of existing
families, and typically added along with a reference board:
- Renesas RZ/G2UL (R9A07G043) is the single-core version of the
RZ/G2L general-purpose MPU.
- Renesas RZ/V2M (R9A09G011) is a smart camera SoC
- Renesas R-Car V4H (R8A779G0) is an automotive chip with Cortex-A76
cores and deep learning accerlation.
- Broadcom BCM47622 is a new broadband SoC based on a quad Cortex-A7
and dual Wifi-6.
- Corstone1000 is a generic platform from Arm that is used for
designing custom SoCs, the support for now is for the Fixed Virtual
Platform emulation for it.
- Mediatek MT8195 (Kompanio 1200) is a high-end consumer chip used in
upcoming Chromebooks.
- NXP i.MXRT1050 is a Cortex-M7 based microcontroller, the first
MMU-less SoC to be added in a while
New machines based on already supported SoCs this time are mainly for
32-bit platforms and include:
- Two wireless routers based on Broadcom bcm4708
- 30 new boards based on NXP i.MX6, i.MX7 and i.MX8 families, mostly
for the industrial embedded market, and on NXP LS1021A based IOT
board.
- Two ethernet switches based on Microchip LAN966
- Eight Qualcomm Snapdragon based machines, including a smartwatch, a
Chromebook board and some phones
- Another phone based on the old ST-Ericsson Ux500 platform
- Seven STM32MP1 based boards
- Four single-board computers based on Rockchip RK3566/RK3568"
* tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (791 commits)
ARM: dts: kswitch-d10: enable networking
ARM: dts: lan966x: add switch node
ARM: dts: lan966x: add serdes node
ARM: dts: lan966x: add reset switch reset node
ARM: dts: lan966x: add MIIM nodes
ARM: dts: lan966x: add hwmon node
ARM: dts: lan966x: add basic Kontron KSwitch D10 support
ARM: dts: lan966x: add flexcom I2C nodes
ARM: dts: lan966x: add flexcom SPI nodes
ARM: dts: lan966x: add all flexcom usart nodes
ARM: dts: lan966x: add missing uart DMA channel
ARM: dts: lan966x: add sgpio node
ARM: dts: lan966x: swap dma channels for crypto node
ARM: dts: lan966x: rename pinctrl nodes
ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
ARM: dts: at91: use generic node name for dataflash
ARM: dts: turris-omnia: Add atsha204a node
arm64: dts: mt8192: Follow binding order for SCP registers
arm64: dts: mediatek: add mtk-snfi for mt7622
arm64: dts: mediatek: mt8195-demo: enable uart1
...
