We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mcasp davinci_mcasp_set_dai_fmt function was overriding ahclkx
input/output status that had already been set by the
davinci_mcasp_set_sysclk function. This commit removes clearing
of the ahclkx input/output status from davinci_mcasp_set_dai_fmt.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CCSR_SSI_SOR is a register that clears the TX and/or the RX fifo
on the i.MX SSI port. The fsl_ssi_trigger writes this register in
order to clear the fifo at trigger time.
However, since the CCSR_SSI_SOR register is not in the volatile list,
the caching mechanism prevented the register write in the trigger
function. This caused the fifo to not be cleared (because the value
was unchanged from the last time the register was written), and thus
causes the channels in both TDM or simple I2S mode to slip and be in
the wrong time slots on SSI restart.
This has gone unnoticed for so long because with simple stereo mode,
the consequence is that left and right are swapped, which isn't that
noticeable. However, it's catestrophic in some systems that
require the channels to be in the right slots.
Signed-off-by: Caleb Crome <caleb@crome.org>
Suggested-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Default channel map is set for 2 channels. Fix the channel map
based on runtime params to support multichannel.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel max is changed to 8 from stereo to support multichannel
capability for HDMI devices.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this patch, chmap controls are created and user space can
set the channel map.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
The patch following the machine driver changes adds the channel
map control in the hdac_hdmi codec driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support multichannel hdac hdmi driver registers with HDA
channel map framework. Channel count and channel slot verbs are
programmed by using the chmap helpers/ops. The channel
allocation is then programmed in the audio infoframe as per CEA
spec.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch parses ELD speaker allocation data block to find
sink's chmap capability.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_mod_call is counting its calling count to avoid unbalanced
function pair calling for error cases (ex init <-> quit).
SSI parent is now controlled as "mod" on current rsnd driver. Because of
this reason, SSI .remove function will be called twice if it was used as
SSI parent when user tried unbind. But probe/remove pair were not
counted. This patch counts probe/remove functions to avoid it.
Special thans Hiep
Reported-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm2835-i2s driver already has support for the S16_LE format but
that format hasn't been made available because dmaengine_pcm didn't
support packed data transfers.
bcm2835-i2s needs 16-bit left+right channel data to be packed into
a 32-bit word, the FIFO register is 32-bit only and doesn't support
16-bit access.
Now that dmaengine_pcm supports packed transfers the format can
be made available by setting the SND_DMAENGINE_PCM_DAI_FLAG_PACK flag.
No further configuration is necessary:
- snd_dmaengine_dai_dma_data.addr_width is already set to
DMA_SLAVE_BUSWIDTH_4_BYTES to force 32-bit DMA transfers
- dmaengine_pcm will pick up the S16_LE format from the DAI
configuration and make it available since it's no longer
masked out due to the PACK flag.
- there are no further corner cases to catch in hw_params,
since the channel count is fixed at 2 we always have two
16-bit stereo samples that can be transferred via 32-bit DMA
Signed-off-by: Matthias Reichl <hias@horus.com>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
dmaengine_pcm currently only supports setups where FIFO reads/writes
correspond to exactly one sample, eg 16-bit sample data is transferred
via 16-bit FIFO accesses, 32-bit data via 32-bit accesses.
This patch adds support for setups with fixed width FIFOs where
multiple samples are packed into a larger word.
For example setups with a 32-bit wide FIFO register that expect
16-bit sample transfers to be done with the left+right sample data
packed into a 32-bit word.
Support for packed transfers is controlled via the
SND_DMAENGINE_PCM_DAI_FLAG_PACK flag in snd_dmaengine_dai_dma_data.flags
If this flag is set dmaengine_pcm doesn't put any restriction on the
supported formats and sets the DMA transfer width to undefined.
This means control over the constraints is now transferred to the DAI
driver and it's responsible to provide proper configuration and
check for possible corner cases that aren't handled by the ALSA core.
Signed-off-by: Matthias Reichl <hias@horus.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If size mismatch of manifest, ABI headers or elements is found, stop
parsing topology info and return the error.
New fields may be append to the tail of ABI objects which will cause
object size to increase. If user space and kernel use different versions
of ABI, size mismatch will be detected here.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stop loading topology info if error happens when creating a widget.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Texas Instruments TAS5720L/M device is a high-efficiency mono
Class-D audio power amplifier optimized for high transient power
capability to use the dynamic power headroom of small loudspeakers.
Its digital time division multiplexed (TDM) interface enables up to
16 devices to share the same bus.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a function to delete and free the contents of the alg_regions list.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure that the wm_adsp driver cleans up when the codec driver
is removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds a wm_adsp2_remove() function to ensure that memory
is freed when the driver is unloaded or shut down.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bits in the ARIZONA_CLOCK_CONTROL register only respond to writes of
a '1', a write of '0' is ignored. So there's no need to use update_bits.
We can do a simple write to set bits.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initialize the dma_slave_config for PCM DMA transfers,
instead of leaving it uninitialized. Keeps previous data on
the stack from giving us invalid values in uninitialized
members of the config structure.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because LRCK of TDM use High to Low as default setting, this patch
changes the TDM setting to inverse LRCK.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT298_CBJ_CTRL1(0x4f) bit 10 is needed for headset capture. It
will be turned off when "VREF" widget is on and be turned on when
bias level is ON. It is odd. And if "VREF" is turned on in bias
level is ON, RT298_CBJ_CTRL1(0x4f) bit 10 will be turned off.
This patch move the bit control from rt298_set_bias_level and
rt298_vref_event to rt298_jack_detect. So it will be turned on
once a jack is plugged in.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt298 need to reset AD filter and the ADC settings will take effort.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to enable the clock if we are a clock master.
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Original work by Zoltan Szenczi.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds 24 bit support to the I2S driver of the BCM2835
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_find_dai() has been exported and so add the kerneldoc comments
for it.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Users have reported seeing this false warning on atom driver
[ 5.647469] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 0 doesn't have DAPM widget!!!
[ 5.661612] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 1 doesn't have DAPM widget!!!
[ 5.661646] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 2 doesn't have DAPM widget!!!
[ 5.661681] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 3 doesn't have DAPM widget!!!
[ 5.661708] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in0_0 doesn't have DAPM widget!!!
[ 5.661738] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in0_1 doesn't have DAPM widget!!!
[ 5.661771] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in1_0 doesn't have DAPM widget!!!
[ 5.661807] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in1_1 doesn't have DAPM widget!!!
This is caused when check for control is not being associated
with a dapm widget, but the check is wrong as the else case
maybe triggered when widget is not powered up, so we should
check if widget is associated before printing this message.
Tested-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA doesn't know about all the different compressed audio formats,
so there is no interface to let userspace enumerate the formats that
are supported by the connected sink. Exporting the raw ELD bytes to
userspace allows an application to select the appropriate audio format
depending on the current capabilities of the connected HDMI sink device.
Usually userspace then just pretends to ALSA that the data is in one of
the raw 16-bit PCM audio formats and relies on the IEC controls to tell
the sink how to interpret the data.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This creates pcmC0D2p for the HDMI playback in the same card.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid complex string manipulations with UUID in canonical
form, use UUID in binary format.
Signed-off-by: Shreyas NC <shreyas.nc@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds second I2S connection to rt5650 codec for capture path on
mt8173-rt5650 machine driver.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When setting up an FLL in pseudo-fractional mode it is preferred
to use a lower FRATIO if possible to give a higher reference clock
frequency. This patch swaps the two loops in arizona_calc_fratio()
so that lower FRATIOs are tried first. The decrementing loop is also
changed to start from init_ratio because the original settings might
already give a fractional value for N.K
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input mixers support routing the IN1_R pin to the Left PGA and the
IN2_L pin to the Right PGA. This patch allows for those routings.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The input pins of the aic3204 have resistors inline with them. The
current code assumes that you want a 10k resistor inline with your
inputs and implements it as a simple switch. This patch creates an enum
for each pin and allows you to switch between not connected, 10k, 20k
and 40k ohm values. This more closely models the acutal aic3204 part.
These pin settings are documented in TI's SLAA557 pages 135 and 136
(http://www.ti.com/lit/ml/slaa557/slaa557.pdf).
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
When creating a FE link, the cpu_dai_name will come from topology and
dpcm will be enabled by default.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This API can be used by topology to find an existing BE dai by name
and further configure it.
Topology will also check DAI ID to avoid wrong match.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology will set the link's generic id when creating a FE link.
Device drivers can check the id for link specific initialization.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The generic ID can be used by topology:
- Toplogy can create FE links and set their ID, machine drivers will
be notified and check this ID for machine-specific init.
- Toplogy can use the ID to find existing BE & CC links and further
configure them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TLV320AIC32x4 series supports 96ksps rates in hardware. This patch
adds the necessary PLL divider values and clock settings to the table to
make 96ksps work.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo 100S netbook has a codec controller for which there is a
driver, but doesn't know how to access the device. This adds the
necessary ACPI table for the driver to find the device.
Device (TTLV)
{
Name (_ADR, Zero) // _ADR: Address
Name (_HID, "10TI3100") // _HID: Hardware ID
Name (_CID, "10TI3100") // _CID: Compatible ID
Name (_DDN, "TI TLV320AIC3100 Codec Controller ") // _DDN: DOS Device Name
Name (_UID, One) // _UID: Unique ID
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Jan Schmidt <jan@centricular.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL function was updated to disallow 32KHz in
commit 501f72e9c5 ("ASoC: da7219: Remove support for 32KHz PLL mode"),
but set_dai_sysclk() was missed and still permits it. This patch resolves
that discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for running the tlv32x4 control channel over SPI rather than I2C.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
To prepare for abstracting adding SPI support, the I2C pieces needs to
be in its own moudle. This patch moves common probe code into aic32x4_probe
and common removal code into aic32x4_remove. It also creates a static
regmap config structure to be copied in the I2C specific driver.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec's probe function is named aic32x4_probe. This is going to
conflict with later work to implement SPI support and separate out I2S
into its own file. In line with other drivers in the tree, this function
is renamed to aic32x4_codec_probe instead.
Signed-off-by: Jeremy McDermond <nh6z@nh6z.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi-codec is a platform device driver to be registered from
drivers of external HDMI encoders with I2S and/or spdif interface. The
driver in turn registers an ASoC codec for the HDMI encoder's audio
functionality.
The structures and definitions in the API header are mostly redundant
copies of similar structures in ASoC headers. This is on purpose to
avoid direct dependencies to ASoC structures in video side driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds DT support for the TI DA8xx/OMAP-L1x/AM17xx/AM18xx McBSP driver.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default, player#0 is connected to I2S/TDM TX bus.
This patch connects player#1 to I2S/TDM TX bus.
Signed-off-by: Moise Gergaud <moise.gergaud@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We request one of the DSP IRQs during CODEC probe, as such we should
free it during CODEC remove, this patch does so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The thermal warning IRQs for the speaker are requested in CODEC probe
but never freed. This patch frees them in CODEC remove.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Documentation/printk-formats.txt has
unsigned long: use %lu or %lx
size_t: use %zu or %zx
runtime->dma_bytes is of type size_t.
runtime->min_align is of type unsigned long.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Documentation/printk-formats.txt has
size_t: use %zu or %zx
runtime->dma_bytes is of type size_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
FW expects sampling rate rounded up to next higher integer value
when calculating ibs/obs. For example for 44.1k, it should be
rounded up to 45 to calculate ibs/obs.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are the changes to enable reader tdm mode:
- When TDM_ENABLE is set to 1, the i2s format should be automatically
configured. Unfortunately this is not the case (HW bug). Then, we shall
force DATA_SIZE setting.
- Compute the transfer size for tdm mode: transfer size = user frame size
- Manage tdm slots configuration given in DT.
- Refine the hw param (channels & format) according to tdm slot config.
Signed-off-by: Moise Gergaud <moise.gergaud@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
here are the changes to enable player tdm mode:
- When TDM_ENABLE is set to 1, the i2s format should be automatically
configured. Unfortunately this is not the case (HW bug). Then, we shall
force DATA_SIZE setting.
- Compute the transfer size for tdm mode: transfer size = user frame size
- Manage tdm slots configuration given in DT.
- Don't use mclk-fs when unip in tdm mode; use tdm slot config to compute
frame size and to set mclk rate.
- Refine the hw param (channels & format) according to tdm slot config.
Signed-off-by: Moise Gergaud <moise.gergaud@st.com>
Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CS47L24 and WM1831 codecs only use the OUT4L widget so we can
skip creation of the OUT4R widget.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
acpi_dev_present() was originally named after pci_dev_present()
to signify the similarity of the two functions.
However Rafael J. Wysocki pointed out that the exported function
acpi_dev_present() is easily confused with the non-exported
acpi_device_is_present(). Additionally in ACPI parlance the term
"present" usually refers to the "device is present" bit returned
by the _STA control method, yet acpi_dev_present() merely checks
presence in the namespace. It does not invoke _STA at all, let
alone check the "device is present" bit.
As suggested by Rafael, rename the function to acpi_dev_found()
and adjust all existing call sites.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch makes Designware I2S driver use the fifo
depth value to program the fifo configuration register
instead of using hardcoded values.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we encounter an error on the DSP side whilst user-space is
waiting on the poll we should call snd_compr_fragment_elapsed,
although data is not actually available we want to wake
user-space such that the error can be propagated out
quickly. Additionally some versions of the DSP firmware are
not super consistent about actually generating an IRQ if they
encounter an error, as such we will check the DSP error status
every time we run out of available data as well, to ensure we
catch it.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Factor out the reading of the DSP error flag into its own function to
support further improvements to the code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the original code we ended the loop with tries set to -1 instead of
zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to unmask all interrupts at I2S start. This
can cause performance issues in slower platforms.
Unmask only the interrupts for the used channels.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the system enters S3 during a playback, codec power needs to
be turned OFF during suspend and restored during resume. With
this patch the AFG node is set to D3 and codec power is turned
OFF during controller suspend call.
During resume, the codec power is left in ON state if the
playback was in progress while suspending.
Also setting power state for AFG node is optimized. With this the
loop with timeout is removed and codec_read is used instead.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_pm ops feature instead of soc pm as core assumes system
is capable of direct complete. Register with complete callback
instead of resume to synchronize with Jack notification from
display driver. This ensures correct Jack notification to user
space.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
IS_ERR_VALUE should be used only with unsigned long type,
signed types should use comparison 'ret < 0'
This patch removes such usages.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes following static checker warning, by initializing the
ret to -EINVAL, as one of the code path in lpass_platform_pcm_new()
uses this variable uninitialized.
sound/soc/qcom/lpass-platform.c:555 lpass_platform_pcm_new()
error: uninitialized symbol 'ret'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The list of TAS571x registers was incomplete.
Added the missing register definitions up to the register 0x25.
Added volatile and read-only register tables into tas5711_regmap_config
and tas5717_regmap_config.
The chip has 256 registers in total. But from address 0x29 on
(0x26 to 0x28 are reserved) the register width varies between
20, 12 and 8 bytes, which the register map cannot represent.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The chip selection was relying only on DT. It was not possible to use the
driver without DT.
This adds the chip type detection from the I2C name, which
allows to use the driver from the platform driver without DT.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton DSP is mostly similar to Skylake one but with subtle
differences like no Code Load DMA and uses HDA DMA for code
loading, DSP D0 and D3 sequences are different.
These changes are comprehended by adding different DSP power up
and down handlers, and new loader ops and also adding prepare and
trigger which HDA DSP DMA requires
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Kranthi G <gudishax.kranthikumar@intel.com>
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add function stub for "sst_acpi_find_name_from_hid()"
when CONFIG_ACPI is not enabled so that the driver will build
successfully. This fixes the following build errors:
(loadable module)
ERROR: "sst_acpi_find_name_from_hid" [sound/soc/intel/boards/snd-soc-sst-bytcr-rt5640.ko] undefined!
(or built-in)
bytcr_rt5640.c:(.text+0x26fc52): undefined reference to `sst_acpi_find_name_from_hid'
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that this is directly user selectable it needs to care about its
dependencies.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver did not have a mute function. The amplifier was brought out of
shutdown mode (hard-mute) once for ever in probe(), which was causing
clicks and pops when altering the I2C register configuration later.
This adds the digital_mute() function. The amplifier unmute in probe()
was removed.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cs47l24 supports the audio trace firmware, this streams of audio to be
captured from the CODEC over a compressed audio channel for
analysis/debugging of audio processing firmwares.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All other debug messages talk about data on the compressed stream in
bytes except avail which is shown in words. To avoid confusion show
avail in bytes as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Firstly, we should be locking the pwr_lock when we initialise the
compressed buffer. Secondly, fixup a couple of places when we should be
pulling pointers only under the pwr_lock as they may be affected by
operations that take that lock.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to use simple card with wm8962 the following probe
error happens:
wm8962 0-001a: simple-card: set_sysclk error
asoc-simple-card sound: ASoC: failed to init 202c000.ssi-wm8962: -22
asoc-simple-card sound: ASoC: failed to instantiate card -22
asoc-simple-card: probe of sound failed with error -22
In simple-card.c the snd_soc_dai_set_sysclk() function is called with
clk_id as 0, which is an invalid clock for wm8962.
Adjust the clocks source definitions in wm8962.h so that the
simple card driver can work successfully.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable dspclk holds the rate of the DSPCLK, but the variable
sysclk holds an identifier for the clock. Currently if read a
non-sensical value from the DSPCLK_DIV register we assign sysclk to
dspclk, clearly this was intended to be sysclk_rate.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The error message fits well into a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When regulator_bulk_enable() fails inside wm8962_runtime_resume(),
we should disable the previously enabled clock.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a menu selection text so that users can enable, disable or
mark it as module in menuconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack plug status is rechecked at resume to handle plug/unplug
in S3 when the chip has no power.
Suspend/resume callbacks are moved from the i2c dev_pm_ops to
snd_soc_codec_driver. soc_resume_deferred is a delayed work
which may trigger nau8825_set_bias_level. The bias change races
against dev_pm_ops, causing jack detection issues.
soc_resume_deferred ensures bias change and snd_soc_codec_driver
suspend/resume are sequenced correctly.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In PRE PMD of widget handler DSP resources are allocated after
the creation of DSP pipe and modules and in POST PMD DSP
resources are destroyed.
If there is any failure in pipe or module creation in PRE PMD,
pcm trigger fails and finally POST PMD gets called and DSP
resources are freed, without getting allocated.
Fixes the DSP resource de-allocation by allocating the resource
before creation of pipe and module in PRE PMD and in POST PMD,
free the resources.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Module needs to be unloaded only when it is loaded successfully.
To fix this, first correct the module state sequence and set module
state to LOADED if module is loaded successfully.
When unloading the module check if module state is not in UNINIT,
then unload it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Cc+v
-----END PGP SIGNATURE-----
Merge tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"After a heavy storm by syzkaller in 4.5 cycle, we have relatively few
changes in the core at this time while a lot of changes are found in
the driver side, unsurprisingly. Below are some highlights:
ALSA core:
- A few more hardening in ALSA timer codes
- An extension of sequencer API for advertising the card / pid
- Small fixes in compress-offload and jack layers
HD-audio:
- Dynamic PCM assignment in HDMI/DP codec; preparation for upcoming
DP-MST support
- Lots of code refactoring for sharing with ASoC SKL driver
- Regression fixes for Intel HDMI/DP
- Fixups for CX20724 codec, Lenovo AiO
USB-audio:
- Add quirk_alias option to make quirk debugging easier
- Fixes for possible Oops by malformed firmware
Firewire:
- Add support for FW-1804 in tascam driver
- Improvements / changes in card registration, multi stream handling,
etc for DICE
- Lots of code refactoring
ASoC:
- Enhancements of still ongoing topology API
- Lots of commits for Intel Skylake support including HDMI support
- A few Intel Atom driver updates for recent devices
- Lots of improvements to the Renesas drivers
- Capture support for Qualcomm drivers
- Support for TI DaVinci DRA7xxx devices
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514"
* tag 'sound-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (291 commits)
ALSA: hda - Fix mutex deadlock at HDMI/DP hotplug
ALSA: ctl: change return value in compatibility layer so that it's the same value in core implementation
ALSA: mixart: silence an uninitialized variable warning
ALSA: usb-audio: Add sanity checks for endpoint accesses
ALSA: usb-audio: Minor code cleanup in create_fixed_stream_quirk()
ALSA: usb-audio: Fix NULL dereference in create_fixed_stream_quirk()
ALSA: hda - Limit i915 HDMI binding only for HSW and later
ALSA: hda - Fix unconditional GPIO toggle via automute
ALSA: mixart: silence unitialized variable warnings
ALSA: hda - Fixes double fault in nvhdmi_chmap_cea_alloc_validate_get_type
ALSA: intel8x0: Add clock quirk entry for AD1981B on IBM ThinkPad X41.
ALSA: hda - Add new GPU codec ID 0x10de0082 to snd-hda
ASoC: rsnd: add simplified module explanation
ASoC: hdac_hdmi: Add broxton device ID
ASoC: Intel: Bxtn: Add Broxton PCI ID
ASoC: Intel: Skylake: Move Skylake dsp ops & loader ops
ASoC: Intel: add dmabuffer to common sst_dsp
ASoC: Intel: Skylake: Unstatify skl_dsp_enable_core
ASoC: Intel: Skylake: Fix whitepsace issues
ASoC: Intel: Skylake: Move module id defines
...
The Skylake driver selects SND_HDA_I915 which causes kbuild to spew warning:
warning: (SND_SOC_INTEL_SKYLAKE) selects SND_HDA_I915 which has unmet direct dependencies
(SOUND && !M68K && !UML && SND && DRM_I915 && SND_HDA_CORE)
The SND_HDA_I915 should not be selected so drop that.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dummy component is reused for all cards so we special case and don't
bind it to any of them. This means that code like that displaying the
component widgets that tries to look at the card will crash. In the
future we will fix this by ensuring that the dummy component looks like
other components but that is invasive and so not suitable for a fix.
Instead add a special case check here.
Reported-by: Harry Pan <harry.pan@intel.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
OMAP3's McBSP2 and McBSP3 module have integrated sidetone block with
dedicated SYSCONFIG register. The sidetone is operating from the maain
McBSP module's ICLK. For normal operation the sidetone clock auto idle
support needs to be disabled when it is activated.
Note: This is not enough to avoid choppy sidetone because this AUTOIDLE
bit is controlling only the clock auto idle from the McBSP to the sidetone
block. If the McBSP_ICLK is idling, the sidetone clock is going to do the
same.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch corrects the interface adc/dac control register definition
according to datasheet.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The PCI bus takes pci_dev_get() and pci_dev_put() is also there.
So no need for drivers to invoke these. In SKL driver we were
calling pci_dev_put() only which is not right, so remove this
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Skylake driver uses i915 component APIs to talk to display.
On remove we should free up by invoking snd_hdac_i915_exit() but
that should be last thing in remove routine, so move it to last
in skl_free()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In Skylake destructor we unmap the hardware address and then free
links and streams. The stream free accesses hardware to write to
registers and predictably causes oops.
So change the order and unmap last in destructor.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are supposed to freeup the Code loader DMA allocation and
ensure all interrupts are disabled before we disable dsp cores.
So invoke these to ensure DSP shuts down properly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On driver removal we should ask the core to remove the device
objects as well, so invoke snd_hdac_ext_bus_device_remove() in
remove.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5616 codec registers itself as an i2c driver, but can
be enabled even when i2c is turned off, which leads to a build
error:
codecs/rt5616.c:1419:1: error: data definition has no type or storage class [-Werror]
module_i2c_driver(rt5616_i2c_driver);
This adds an explicit Kconfig dependency, like the other codec
drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 288bc356a8 ("ASoC: rt5616: allow to build with CONFIG_SND_SOC_RT5616")
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW58EWAAoJECTWi3JdVIfQMGMH/1v4ojMy0X/yPlFk/523u7uq
6ZJQ4zSTPyv0ccR+hsDjZ81BmM/vATrnQOllvTSwfnGMcs5amE3/9EhzdF5EciCB
8gUff/GfugXNqpVgpfYYfPhbQVTGllOFnZPmXsLx2dGlu094i69f4fZtoJCFlkmo
5c0L5Fnkt4w5XtFAA6ILuRtpwZ4jfJZ3VFKrtYwkgLcKw9GgSEqhVKvTPfkNqtjg
hzEl2P2K/Ug2uTqeZusKH30Sa1J7MW4B+C9dUVyTRB29+uA60y0foGTQjW9uCzEi
l1sqY9VDSKp9WwnshVrgVFViAhkrA7fWl4qaC/EDe7avvbh5SBpR/+gjZbmdRJU=
=jEl0
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been an extremely quiet release for the regulator API, aside
from bugfixes and small enhancements the only thing that really stands
out are the new drivers for Action Semiconductors ACT8945A, HiSilicon
HI665x, and the Maxim MAX20024 and MAX77620"
* tag 'regulator-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (46 commits)
regulator: pwm: Add support to have multiple instance of pwm regulator
regulator: pwm: Fix calculation of voltage-to-duty cycle
regulator: of: Use of_property_read_u32() for reading min/max
regulator: pv88060: fix incorrect clear of event register
regulator: pv88090: fix incorrect clear of event register
regulator: max77620: Add support to configure active-discharge
regulator: core: Add support for active-discharge configuration
regulator: helper: Add helper to configure active-discharge using regmap
regulator: core: Add support for active-discharge configuration
regulator: DT: Add DT property for active-discharge configuration
regulator: act8865: Specify fixed voltage of 3.3V for ACT8600's REG9
regulator: act8865: Rename platform_data field to init_data
regulator: act8865: Remove "static" from local variable
ASoC: cs4271: add regulator consumer support
regulator: max77620: Remove duplicate module alias
regulator: max77620: Eliminate duplicate code
regulator: max77620: Remove unused fields
regulator: core: fix crash in error path of regulator_register
regulator: core: Request GPIO before creating sysfs entries
regulator: gpio: don't print error on EPROBE_DEFER
...
gcc warns about the possibilty of accessing a property read from
devicetree in cs35l32_i2c_probe() when it has not been initialized
because CONFIG_OF is disabled:
sound/soc/codecs/cs35l32.c: In function 'cs35l32_i2c_probe':
sound/soc/codecs/cs35l32.c:278:2: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
The code is actually correct because it checks the dev->of_node
variable first and we know this is NULL here when CONFIG_OF
is disabled, but Russell King noticed that it's broken when
we probe the device using DT, and the properties are absent.
The code already has some checking for incorrect values, and
I keep that checking unchanged here, but add an additional
check for an error returned by the property accessor functions
that now gets handled the same way as incorrect data in the
properties.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull dma_*_writecombine rename from Ingo Molnar:
"Rename dma_*_writecombine() to dma_*_wc()
This is a tree-wide API rename, to move the dma_*() write-combining
APIs closer in name to their usual API families. (The old API names
are kept as compatibility wrappers to not introduce extra breakage.)
The patch was Coccinelle generated"
* 'mm-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dma, mm/pat: Rename dma_*_writecombine() to dma_*_wc()
The main thing in terms of the core this time around has been some
additional framework work for dynamic topologies (though we *still*
don't appear to have a stable ABI for the topology code, it's probably
worth considering if this will ever happen...). Otherwise the work has
almost all been in the drivers:
- HDMI support for Sky Lake, along with other fixes and enhancements
for the Intel drivers.
- Lots of improvements to the Renesas drivers.
- Capture support for Qualcomm drivers.
- Support for TI DaVinci DRA7xxx devices.
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs.
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW5qP+AAoJECTWi3JdVIfQJhAH/RKv268gjE07uJ8jeGAT7uY4
XM19VmUl7ZOlphctfr/I+1hRwo+mgGN4LSfKnXxsPk9Uq/WJUok4D7MjDN33jeX/
heK9WAO8zXkgi9n2lhGI/z9uE76kPA/Qw0aEYcbmA6bDc4GF3AKphnByh6kDShtE
BfblofsFaDywA09XQ2lh3wW0rZtJ51tQUeOi35UADyEPzQetzN+xiY85Bkia5BEt
Yjp37nLJET8Gk0r9snE2MpACUkEyw7CiPXCjkK47npia41LVnTarZAq5+JmfKygg
YV2EnC3AFYthhjZPfmO1usI2vJVwkN40nGrKipH2QX08TanK8r2qiTsmGADNX4E=
=0/1R
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.6
The main thing in terms of the core this time around has been some
additional framework work for dynamic topologies (though we *still*
don't appear to have a stable ABI for the topology code, it's probably
worth considering if this will ever happen...). Otherwise the work has
almost all been in the drivers:
- HDMI support for Sky Lake, along with other fixes and enhancements
for the Intel drivers.
- Lots of improvements to the Renesas drivers.
- Capture support for Qualcomm drivers.
- Support for TI DaVinci DRA7xxx devices.
- New machine drivers for Freescale systems with Cirrus CODECs,
Mediatek systems with RT5650 CODECs.
- New CPU drivers for Allwinner S/PDIF controllers
- New CODEC drivers for Maxim MAX9867 and MAX98926 and Realtek RT5514.
Renesas sound driver user needs to read its datasheet when create DT.
But it is difficult to understand, because it has many modules
(SRC/CTU/MIX/DVC/SSIU/SSI/AudioDMAC/AudioDMACperiperi),
and many features (Asynchronous/Synchronous mode on SRC, CTU matrix,
DVC volume settings feature, Multi-SSI/TDM-SSI, etc).
This patch adds simplified explanation to help setting/understanding.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton HDMI codec is similar to Skylake so add the device ID
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton is an Intel SoC which sports a DSP and system is quite
like Skylake. So add this ID in Skylake driver
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code loading for Skylake and other platforms is different, so
add a dsp_ops and a loader_ops which can be defined for each
platform.
Move the dsp init, cleanup and loader ops (alloc and free dma) to
these ops
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Broxton uses HDA DMA so needs to keep dmab in the driver context
so add it
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function skl_dsp_enable_core will be called by other parts of
driver so this can no longer be a static function.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: GuruprasadX Pawse <guruprasadx.pawse@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some double whitespaces issues existed in driver, so fix them up.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module ID defines are common to other platforms so can be
reused if moved to a common driver header so move it
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reduce pop noise in power up and down sequence when playback.
The DAPM widgets graph is reconstructed to ensure the
register write sequence at playback matches exactly to the
v5 clickless sequence provided by Nuvoton.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
While building m32r allmodconfig the build failed with:
ERROR: "bad_dma_ops" [sound/soc/qcom/snd-soc-lpass-platform.ko] undefined!
ERROR: "dma_common_mmap" [sound/soc/qcom/snd-soc-lpass-platform.ko] undefined!
To satisfy the dependency CONFIG_SND_SOC_LPASS_PLATFORM should depend
on HAS_DMA.
Some other configs also needs the dependency on HAS_DMA as they are
directly or indirectly selecting SND_SOC_LPASS_PLATFORM.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of depending on individual SoCs make the edma-pcm depend on the eDMA
dmaengine driver (TI_EDMA).
Update the help text and add DRA7xx family since they have eDMA integrated
as well along with sDMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case when the dai format is set via the dai_link the format
configuration happens once when the links are probed. If the McASP lose
context after this, the information will be lost and McASP will not going
to work correctly.
To overcome this issue, we save the fmt and set it within hw_params as
well.
Reported-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 44029e9e1290 ("ASoC: wm_adsp: wm_coeff_{read|write}_control should use passed length")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio infoframe used incorrect buffer, so fix it.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are getting build warning about:
sound/soc/codecs/rt5640.c:1892:11: warning: unused variable 'dai_sel'
The use of the variable was removed but the variable itself was not
removed.
Fixes: c467fc0e01 ("ASoC: rt5640: Set PLL src according to source")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
CMD.out should use same as SRC.out for TIMSEL settings,
but it cares Playback case only. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC has Sync/Async mode, and it can't use Sync mode when Capture
with CMD. In Async mode, it needs to care about in/out SRC rate
for settings, but current driver supporting Playback case only.
This patch supports Capture case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC will convert rate, and then, CMD and SSI want to know its
rate (= SRC.in / SRC.out) for each purpose.
Current driver is supporting only Playback, but SRC+Capture support
needs more flexibility.
This patch adds rsnd_src_get_in/out_rate() for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_enable_sync_convert() is for checking, not for setting.
In order to avoid confusion, this patch renamed it to
rsnd_src_sync_is_enabled()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce confusion, SRC uses "mod" instead of "src"
as function parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC sync mode needs to control its clock (= for in/out). 1st but codec
side clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can't use SRC Synchronous convert when Capture if it uses CMD,
because no one provide out side clocks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC1/2 power is for both DACs and related mixer/mux. Add SUPPLY
type widgets to support it.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5640_set_dai_pll set pll source according to given source and
dai id. However, the pll source should be set according to given
source only.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes coccicheck report:
Unneeded variable: "ret". Return "0" on line 2817
Remove unneccesary variable ret created to return zero.
Signed-off-by: Rajan Vaja <rajan.vaja@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the necessary device tree compatible string to allow DT
probing.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
This should be more robust to future changes than adressing
array entries by index number.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds CTU (= Channel Transfer Unit) support on
Renesas R-Car sound driver.
It can Down/Up mixing and splitter. You need to check R-Car datasheet
especially CTUn_CPMDR/CTUn_SV0xR/CTUn_SV1xR/CTUn_SV2xR/CTUn_SV3xR
for setting parameter.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI is supporting Normal SSI/Multi mode SSI/TDM mode SSI
and its behavior is based on input channels.
This input channel might be converted by CTU,
and SSI needs to be Multi SSI mode / TDM SSI mode if 6ch input
EX) 6ch input, CTU for 2ch, playback
6ch 6ch 2ch 2ch 2ch 2ch
-> SRC -> CTU -> MIX -> DVC -> SSIU -> SSI
EX) 6ch input, no CTU, Multi SSI, playback
6ch 6ch 6ch 6ch 6ch 2ch
-> SRC -> CTU -> MIX -> DVC -> SSIU -> SSI0/SSI1/SSI2
Current driver is using rsnd_get_adinr_chan() / rsnd_get_slot_width()
for this purpose, but it is complicated enough without meaning.
This patch adds new rsnd_runtime_channel_xxx() which is caring
CTU/Multi SSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Renesas R-Car sound CTU (= Channel Transfer Unit)
very basic support, but not yet enough feature at this point.
Because CTU support needs more complex channel function for
each modules.
To avoid complex patch reviewing, this patch picked up very basic
part only.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound device has CTU (= Channel Transfer Unit), and
sound card needs its support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some CHT-T platforms make use of the Realtek RT5640 codec. Make use
of the machine driver developed for Baytrail.
Tested on Tronsmart Ara X5.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove hard-coded generation of codec name, use translation routine
to avoid issues with codec name not matching what the ACPI subsystem
registered
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BIOS vendors sometimes declare multiple devices in the DSDT
table that all refer to the same HID. This is not very smart
but not illegal as long as only one device reports present with
the _STA method. The ACPI subsystem tracks each device with an
extension, e.g. 10EC5640:00 and 10EC5640:01
In the ASoC machine driver, the DAI codec name needs to refer to the
ACPI device that reported present, e.g. "i2c-10EC5640:01". The
extension will vary depending on how the BIOS is written and which
ACPI device is activated.
This patch adds a translation function that provides the codec
name from the ACPI HID to avoid any hard-coded values in the
machine driver.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BIOS vendors typically list multiple audio codecs in the DSDT
table and enable the relevant one by changing the return value
of the _STA method.
With the current code, all devices are reported by
acpi_dev_present(), regardless of the _STA return values. This
causes errors on probe with the wrong machine driver being loaded.
This patch essentially reverts 'commit 6f08cbdaac
("ASoC: Intel: Use acpi_dev_present()")' and adds code to
force the evaluation of the _STA method.
A better solution might be to make sure the ACPI subsystem only
reports devices with a _STA value of 0xf but apparently it's
problematic so dealing with this in the audio subsystem directly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch add compatible for rk3366/rk3368/rk3399 spdif,
these three spdifs share the same type.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While building we were getting build warning about:
sound/soc/codecs/pcm3168a.c:403:21: warning: variable 'channels' set but
not used
The variable channels were being assigned some value but that was never
reused.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rockchip spdif driver uses SIMPLE_DEV_PM_OPS to conditionally
set its power management functions, but we get a warning
about rk_spdif_runtime_resume being unused when CONFIG_PM is not
set:
sound/soc/rockchip/rockchip_spdif.c:67:12: error: 'rk_spdif_runtime_resume' defined but not used [-Werror=unused-function]
This adds a __maybe_unused annotation so the compiler knows
it can silently drop it instead of warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes that hasn't built the rt5616 driver with
'CONFIG_SND_SOC_RT5616=y' in .config.
The tristate is the prompt on the 'make menuconfig',
in other words, that can't show the prompt and select it
if we don't say what's the tristate.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cpu_dai id always equals 0, can't distinguish the
different SSC. Use platform_device id to record
and distinguish the different SSC.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the DPCM based machine driver with rt5650 and rt5514.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some R-Car sound requests picky register access which needs *force*
register write.
Some status register needs to set 1 to clear status, but we might
read 1 from its register. In such case, current regmap does nothing
and driver will be forever loop
To reduce code complexity, this patch uses regmap _force_
function for all register access.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IVI loop is removed in skl_nau88l25_ssm4567 machine as we
enable this path thru DAPM graph using the PCM device and not
thru loop
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can enable the IVI feedback path by connecting Left/Right
speaker sensors (codec) to ssp0 Rx (soc-dsp). This way aDSP gets
feedback data from codec to DSP algorithms
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The blob query for BE skl_tplg_update_be_blob() was not using
right values for direction for blob query, so fix that.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The firmware ctls like "DSP1 Firmware" in wm_adsp codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"Speaker Mode "ctl in wm9081 codec driver is enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DSP1 EQ Mode" and "DSP2 EQ Mode" ctls in wm8996 codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DRC Mode like "AIF1DRC1 Mode" and EQ Mode like "AIF1.1 EQ Mode" in
wm8994 codec driver are enum ctls, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"Equalizer Function" ctl in wm8985 codec driver is enum, while the
current driver accesses wrongly via value.integer.value[]. They have
to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Equalizer Function" ctl in wm8983 codec driver is enum, while the
current driver accesses wrongly via value.integer.value[]. They have
to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"MBC Mode", "VSS Mode", "VSS HPF Mode" and "Enhanced EQ Mode" ctls in
wm8958 codec driver are enum, while the current driver accesses
wrongly via value.integer.value[]. They have to be via
value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
"DRC Mode" and "EQ Mode" ctls in wm8904 codec driver are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DAI Mode" ctl in wm8753 codec driver is enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Codec Mode" and "Audio Switch" ctls in wl1273 codec driver are enum,
while the current driver accesses wrongly via value.integer.value[].
They have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"FIFO Mode" ctl in tlv320dac33 codec driver is enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Biquad1 Mode" and "Biquad2 Mode" ctls in max98095 codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"EQ1 Mode" and "EQ2 Mode" ctls in max98088 codec driver are enum,
while the current driver accesses wrongly via value.integer.value[].
They have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Sidetone Status" and "ANC Status" ctls in ab8500 codec driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DAC1 High Pass Filter Mode" & co in da732x codec driver are enum,
while the current driver accesses wrongly via value.integer.value[].
They have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"PCM channel mixer" ctl in cs42l51 codec driver is enum, while the
current driver accesses wrongly via value.integer.value[]. They have
to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Playback Switch" and "Lineout Mux" ctls in medfld machine driver are
enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Speaker Function", "Input Select" and "Jack Function" ctls in rx51
driver are enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function", "Speaker Function" and "Input Select" ctls in n810
driver are enum, while the current driver accesses wrongly via
value.integer.value[]. They have to be via value.enumerated.item[]
instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function" and "Speaker Function" ctls in tosa are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function" and "Speaker Function" ctls in spitz are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function" and "Speaker Function" ctls in poodle are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Input Select" ctl in magician driver is an enum, while the current
driver accesses wrongly via value.integer.value[]. They have to be
via value.enumerated.item[] instead.
(Meanwhile "Headphone Switch" and "Speaker Switch" are boolean, so
they should stay to access via value.integer.value[] as is.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
"Jack Function" and "Speaker Function" ctls in corgi are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_dapm_dai_link_get() and _put() access the associated ctl
values as value.integer.value[]. However, this is an enum ctl, and it
has to be accessed via value.enumerated.item[]. The former is long
while the latter is unsigned int, so they don't align.
Fixes: c66150824b ('ASoC: dapm: add code to configure dai link parameters')
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable cmd_id is only assigned some value and is never used.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The cs4271 has three power domains: vd, vl and va.
Enable them all, as long as the codec is in use.
While at it, factored out the reset code into its own function.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add these widgets to allow another path from I2S input.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We cannot use strcpy() to write to a const char * location. This is
causing a 'BUG: unable to handle kernel paging request' error at boot
when using the cht-bsw-rt5645 driver.
With this patch we also fix a wrong indexing in the driver where the
codec_name of the wrong dai_link is being overwritten.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To improve I2S flow, this patch removes soft reset and adds second
I2S clock to use.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As pointed out by Zhangfei Gao, the sspa_div variable in
brownstone_wm8994_hw_params() is completely unused, so as a cleanup
following a prior patch, this removes both the variable and the division.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Headphone needs enough delay time before unmuting for avoiding pop sound.
We extend the delay time to make sure headphone doesn't pop.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When playing audio through headphone, headphone makes pop noise if system
resumes from S3 to S0. We modify the sequence of writing register for
avoiding pop sound.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch complains that we might reach the end of this loop without
finding what we're looking for leading to a buffer overflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WoV module needs to be triggered with PCM open, so remove this as
DAPM Sink and will be connected to FE
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WoV module needs to be triggered with PCM open, so remove this as
DAPM Sink and will be connected to FE
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
WoV module needs to be triggered with PCM open, so remove this as
DAPM Sink and will be connected to FE
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSM4567 supports IV feedback for feedback to the speaker
protection algorithm
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds 2 HDMI FE and BE dai links and also
initializes the jack for each device.
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds 2 HDMI FE and BE dai links and also
initializes the jack for each device.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake platform has 3 pin widgets in HDMI codec. This patch adds
3 FE and BE dai links to support these in rt286 machine
Also add jack initialization for each of the device.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ function should not be enabled before irq handler is registered.
In fact, it is done in rt298_probe. So remove it from rt298_i2c_probe.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some registers needed for enabling rt298 IRQ missed on
current driver.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The debug logging of FLL calculations was confusing. Values were
printed in hex without indicating this by a leading 0x, and
despite these normally being required in decimal. Also where the
register value isn't the actual value (it s a power-of-two or
0 means 1, 1 means 2, ...) it was unclear whether the actual or
register value was shown.
This patch changes the log print so that all mathematical values
are shown in decimal, all register values are shown in hex with a
0x prefix, and where the register value isn't the actual integer
value the decimal integer value is shown in () after the hex
register value.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
value variable can contain error values and is compared with zero.
Its type must be signed.
The problem has been detected using coccinelle script
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the conversion to regmap, I assumed that the devm_() variant could be
used in the soc probe function.
As a mater of fact with the current code the regmap is freed twice
because of the devm_() call:
(mutex_lock) from [<c01f6624>] (debugfs_remove_recursive+0x50/0x1d0)
(debugfs_remove_recursive) from [<c02bf800>] (regmap_debugfs_exit+0x1c/0xd4)
(regmap_debugfs_exit) from [<c02ba1f8>] (regmap_exit+0x28/0xc8)
(regmap_exit) from [<c02aa258>] (release_nodes+0x18c/0x204)
(release_nodes) from [<c02a278c>] (device_release+0x18/0x90)
(device_release) from [<c0239030>] (kobject_release+0x90/0x1bc)
(kobject_release) from [<c0395c94>] (wm9713_soc_remove+0x1c/0x24)
(wm9713_soc_remove) from [<c0384884>] (soc_remove_component+0x50/0x7c)
(soc_remove_component) from [<c0386c28>] (soc_remove_dai_links+0x118/0x228)
(soc_remove_dai_links) from [<c038721c>] (snd_soc_register_card+0x4e4/0xdd4)
(snd_soc_register_card) from [<c0393c54>] (devm_snd_soc_register_card+0x34/0x70)
Fix this by replacing the devm_regmap initialization code with the non
devm_() variant.
Fixes: 700dadfefc ASoC: wm9713: convert to regmap
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the recent integration of kctl jack and input jack layers, we
can basically build the jack layer even without input devices. That
is, the jack layer itself can be built with conditional to enable the
input device support or not, while the users may enable always
CONFIG_SND_JACK unconditionally.
For achieving it, this patch changes the following:
- A new Kconfig, CONFIG_SND_JACK_INPUT_DEV, was introduced to indicate
whether the jack layer supports the input device,
- A few items in snd_jack struct and relevant codes are conditionally
built upon CONFIG_SND_JACK_INPUT_DEV,
- The users of CONFIG_SND_JACK drop the messy dependency on
CONFIG_INPUT.
This change also automagically fixes a potential bug in HD-audio
driver Arnd reported, where the NULL or uninitialized jack instance is
dereferenced.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The codec registers are reset during S3. So need to reconfigure
all pins and DP1.2 feature again after resume from S3. Also
reprogram the required registers if the S3 was triggered during
playback.
In suspended state ELD notify callback is not processed, So add
ELD check for all pins as well.
Also turn the codec power domain OFF which is kept ON during
controller resequencing and codec reenumeration.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Powering off codec immediately after sending D3 verb may not set
the node to D3 state. So wait for a confirmation response before
shutting down codec.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the DPCM based machine driver with rt5650
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
enable/disable master clock when codec is active or not.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch add default values for registers according description from TRM.
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Directly set a stream's rates, rate_min and rate_max from the topology
info. Also define set_stream_info to wrap setting of the stream info.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If dai_link is already bound then we just returned and leaked rtd and
rtd->codec_dais which were allocated by soc_new_pcm_runtime(). We do not
need this newly allocated rtd to check if dai_link is already binded. Lets
check first if it is already binded before allocating this memory.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are getting build warning about:
sound/soc/soc-topology.c:249:31: warning: 'get_dobj_type' defined but
not used
commit 64527e8a35 has removed the only caller of get_dobj_type() but
missed to remove the function which is now unused. And after removing
get_dobj_type() we do not have any use of get_dobj_mixer_type().
Fixes: 64527e8a35 ("ASoC: topology: Add FE DAIs dynamically")
CC: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add devicetree bindings for i2s controller found on rk3399
processors from rockchip.
It's helpful to add full set of compatible strings for serials
of Rockchip SoCs (rk3066, rk3188, rk3288, rk3399).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dfw_ac->params is an array not a pointer. It will never be NULL. The check
on ac->max appears sufficient.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no guarantee that on fsl_ssi module load
SSI registers will have their power-on-reset values.
In fact, if the driver is reloaded the values in
registers will be whatever they were set to previously.
However, the cache needs to be fully populated at probe
time to avoid non-atomic allocations during register
access.
Special case here is imx21-class SSI, since
according to datasheet it don't have SACC{ST,EN,DIS}
regs.
This fixes hard lockup on fsl_ssi module reload,
at least in AC'97 mode.
Fixes: 05cf237972 ("ASoC: fsl_ssi: Add driver suspend and resume to support MEGA Fast")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5c408fee25 ("ASoC: fsl_ssi: remove explicit register defaults")
causes the driver to fail to probe:
fsl-ssi-dai 2028000.ssi: No cache defaults, reading back from HW
fsl-ssi-dai 2028000.ssi: Failed to init register map
fsl-ssi-dai: probe of 2028000.ssi failed with error -22
, so revert this commit.
Reported-by: Mika Penttilä <mika.penttila@nextfour.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm_coeff_{read|write}_control were using the control length rather than
the length parameter passed to them. This is not causing any issues as
the two values are currently always the same, but this needs fixed to
allow future improvements.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the case where the firmware does not tell us the access flags for the
control, we let ALSA select a default (READWRITE). But really we should
be applying the volatile flag in this case, as we will read the control
from the DSP if it is on in this case. This patch explicitly sets the
access flags in all cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a very small window between then wm_adsp_compr_free gets call
and when the DSP is actually powered down. If we get an IRQ from the DSP
in this window then the wm_adsp_compr pointer will be NULL. This patch
adds a check for this into the IRQ handler to avoid any issues when this
happens.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The sun4i, sun5i and sun7i SoC families have an SPDIF
block which is capable of playback and capture.
This patch enables the playback of this block for
the sun4i families.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing DAPM pins and enable jack detection on those pins for
Cherrytrail and Braswell.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds wrdma support in lpass-apq8016 by providing the register
offsets and adding support in dma channel allocation callback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add mic support on apq8016-sbc board aka db410c. Tested it
with headset mic.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds mic support to the lpass driver, most of the driver is
reused as it is, only the register level access is changed depending on
te direction of the stream.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we are ready to access wrdma registers, set the max register
and other regmap related configs to use correct values.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds generic masks for accessing bits in rdma/wrdma
registers. Doing this would simplify the driver and adding capture
support would be much simpler. Also there is no point in having same
bit masks for bits in both rdma and wrdma registers.
This patch also deletes the RDMA specific bit masks and makes the code
use the generic bit masks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds wrdma registers into the lpaif-reg.h.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds mic related bitmasks and offsets in the i2c control
register.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds wrdma related register offsets to the lpass variant data
of ipq806x.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rdma_ch_bit_map can be reused for wrdma channel allocations as wrdma
channel numbering start after rdma channel numbers.
With capture support referring rdma_ch_bit_map for wrdma channel allocation
is confusing, so renaming rdma_ch_bit_map to dma_ch_bit_map makes sense.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ipq806x is only ever tested for playback so return error in dma allocation
if the stream direction is capture.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the internal dma allocation callbacks to take the
stream direction so that it can allocate channels suitable for that
stream direction. Before the capture support this was not necessary.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames rdmactl_audif_start to dmactrl_audif_start as this
is common for both rdma and wrdma. Without this patch the name would be
bit misleading to the readers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds wrdma related register offsets, wrdma channel start
and shifts into lpass variant structure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point in having local allocation functions when the driver
can use snd_dma_alloc/free() apis. This patch replaces the local versions
of the dma allocation apis with the snd_dma_alloc/free() apis.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A rather large batch of fixes here, almost all in the Intel driver.
The changes that got merged in this merge window for Skylake were rather
large and as well as issues that you'd expect in a large block of new
code there were some problems created for older processors which needed
fixing up. Things are largely settling down now hopefully.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWvSlHAAoJECTWi3JdVIfQfngH/jCOXWPiFqHlN5/zFqiARO53
1oqBklDvN/XujUBcOVOeA+YYI8+KbUGNIwt7N0KkdXAHOUi7h8JKj+oH6D6SYX+g
zTLQwvc3Ijy0LCjWqsb6gaZWvkrRRzp2MWbeUym3ppESV823StqiUdH9NMWnn4NV
zUV8BZm9KW+X468OuvNWP3QA7Z1cxE6df8nKlrI9111jd/VR1tLr0eNRxnDWalBB
ZGLnQCC9AtisYrwAr6Bgpsh9U3Ty+LUSO0bKsH63+pRkBIcGQcm1E/JQse/o39M3
VfJ8R1+683atnreNepBCiId+tSugzcRWxiRYpStDCGAiZe70wBJHRld0YTj0GuM=
=P9e4
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.5-rc4' into asoc-qcom
ASoC: Fixes for v4.5
A rather large batch of fixes here, almost all in the Intel driver.
The changes that got merged in this merge window for Skylake were rather
large and as well as issues that you'd expect in a large block of new
code there were some problems created for older processors which needed
fixing up. Things are largely settling down now hopefully.
This patch enables HDMI support in passthrough mode in skylake.
Skylake supports 3 pin widgets in HDMI codec, so add 3 FE and 3
BE dais
Add required hw info, formats, rates to support HDMI.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SKL also supports HDMI output so in probe we need to enable
the HDMI using common i915 APIs to ensure it gets probed on the
bus
After S3 during the controller resequencing the codec domain need
to be kept ON for successful reconfiguration of Codec. Once
configured it will be turned OFF in codec driver.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set required parameters for hdac_ext_dma_params object instead of
skl_dma_params.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register are reset during the D3 to D0 transition. So
reconfigure them.
Also as all DAIs are now supported, remove the dai id check in prepare.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec power is turned OFF in the first explicit call to
pm_runtime_suspend to keep the i915 refcount balanced. During regular
operation, the power is turned ON/OFF in runtime PM handlers.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In dai startup, driver was checking for ELD and would fail if no
monitor is connected. This causes userland like PA, CRAS to be
unhappy as they scan the device list at bootup.
So move the ELD check to hw_params and fail if valid ELD is not
found.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's possible for hw_params to be called two times. So add NULL
check to prevent memory leak.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd supports multi SSI (maximum 4 SSI for 8ch),
and, it should determine whether using each SSI or not in runtime.
All SSIs are not used even if there are 4 SSI in case of stereo.
Current driver setups un-used SSI in such case. It is no problem,
but not needed. This patch judges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd supports multi SSI (maximum 4 SSI for 8ch),
and, it should determine whether using each SSI or not in runtime.
Current judgement is vague, and had broken by
c308abe45e2("ASoC: rsnd: rsnd_ssi_is_multi_slave() macro uses
rsnd_ssi_multi_slaves()")
This patch makes clean it, and solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
prepare for runtime judging for SSI work
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Parent SSI is needed if it is PIN sharing and clock master,
otherwise, not needed. But, whether clockk master is judged on
.set_fmt, thus, it can't call rsnd_ssi_parent_attach() on .probe.
Now, .pcm_new will be called after .set_fmt, so this patch reuses it
at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI want to have SSIWSR settings and SSICR settings without EN bit
when init, and SSICR EN bit only when start timing.
Otherwise, SSI output signal might be unstable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b5b442abd9 ("ASoC: rsnd: add .irq callback") added .irq callback
but SSI DMA is missing it. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b5b442abd9 ("ASoC: rsnd: add .irq callback")
added .irq support, and it cares both parent SSI and normal SSI.
But it should care only normal SSI. Otherwise SSI might be
forever loop if SSI is used as both parent SSI and normal SSI
(= 2 users), and if under/over run error happen. Because irq disable
do nothing in such case. This patch solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce confusion, SSI uses "mod" instead of "ssi"
as function parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC_ROUTE_MODE0 determines whether to use SRC.
Thus, it should be setup before SRC_SRCIR.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels number is not only for DVC. Let's rename it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
NHLT table [1] header has fields like oem_id, oem_table_id and
oem_revision. Use that to load a unique topology binary specific
to that platform
NHLT Table is documented at:
[1]: https://01.org/blogs/2016/intel-smart-sound-technology-audio-dsp
Signed-off-by: Yang A Fang <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_tplg_tlv_control_set does pointer maths on data but forgets that data
is not uint8_t so the maths is already scaled in the pointer type.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lockdep warns of a potential lock inversion, i2s->lock is held numerous
times whilst we are under the substream lock (snd_pcm_stream_lock). If
we use the IRQ unsafe spin lock calls, you can also end up locking
snd_pcm_stream_lock whilst under i2s->lock (if an IRQ happens whilst we
are holding i2s->lock). This could result in deadlock.
[ 18.147001] CPU0 CPU1
[ 18.151509] ---- ----
[ 18.156022] lock(&(&pri_dai->spinlock)->rlock);
[ 18.160701] local_irq_disable();
[ 18.166622] lock(&(&substream->self_group.lock)->rlock);
[ 18.174595] lock(&(&pri_dai->spinlock)->rlock);
[ 18.181806] <Interrupt>
[ 18.184408] lock(&(&substream->self_group.lock)->rlock);
[ 18.190045]
[ 18.190045] *** DEADLOCK ***
This patch changes to using the irq safe spinlock calls, to avoid this
issue.
Fixes: ce8bcdbb61 ("ASoC: samsung: i2s: Protect more registers with a spinlock")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Current code calculates blr_clk_ratio before setting max98926->ch_size, fix
it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: anish kumar <yesanishhere@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 4a3478debf ("ASoC: hdac_hdmi: Add jack reporting")
leads to the following Smatch complaint:
sound/soc/codecs/hdac_hdmi.c:971 hdac_hdmi_present_sense()
warn: variable dereferenced before check 'edev' (see line 967)
As explained by Subhransu S. Prusty:
"This NULL check is not required, can be removed.
edev object is expected to be present when the present_sense is
called. This is called from places where this edev object is
already available."
So remove the evdev NULL check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For DP audio support, infoframe needs to be different. Based on
get_conn_type result we pack either HDMI or DP infoframe.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Last patch added infrastructure to render over all the ports,
PCM<->cvt<- pin mapping and user selection of controls. But we
still have restriction of playback on the default port alone, so
remove that.
This patch removes the hardcoding of cvt<->pin map from the dai.
Cvt and pin for a dai are now derived from the already stored pcm
list of device opened. We query connection list of a pin from
codec to validate the cvt<->pin map.
If connection list returns zero, then monitor is not connected so
fail playback.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack is created based on pcm devices enumerated, so we will
create Jack as "HDMI/DP, pcm=x Jack". This style is expected by
current usermode like PulseAudio and CRAS.
This patch exports an API which can be used to register Jack
based on PCM. This API also establishes the map between PCM and
cvt. Further cvt to pin mapping is established with the help of
usermode selection based on the board topology.
During device probe as the PCMs may not be registered, initial
pin sense don't report jack events. So, first time jack reporting
is done during user selection of mux control.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In skylake, HDMI codec enumerates 3 pins and 3 cvts. Stream can
be routed from any cvt to any pin based on the connection list
queried from the pin.
This patch removes the static modelling of widget/route and
creates it dynamically based on the codec widgets enumerated.
Mux widgets are added to represent the map between a cvt and pin.
Ideally the mux widgets should be created based on the connection
list queried from the pin widget. But due to HW behavior, if an
external display is not connected on a port, querying the
connection list returns zero. So create mux widgets to map all
the cvt to all pins. At runtime, playback support on a pin can be
verified based on the connection list query.
Few function in driver have additional arguments now to support
this.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After enabling all pins/cvts, Skylake HDMI codec enumerates 3
converters. Three independent streams can be supported with 3
cvts. This patch removes the static dai creation and creates dais
based on the number of cvts queried.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake supports 3 pin and 3 converter widgets. But by default
only one converter and pin widget are enabled. In skylake
platform the DP port is on a different port which is not enabled
by default. To enable playback on DP port, enable all pin and
converter widget by sending a vendor VERB for a vendor widget to
set required bits.
As we are enabling the DP support enable the DP1.2 feature as well.
Enabling DP1.2 and all widget changes are copied from patch_hdmi.c.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Uses the drm ELD core framework to apply rate and channel
Also compute the format to be set based on ELD.
Even though the channel constraint is based on ELD, infoframe
is set with stereo only. Multichannel support will be added
later.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch uses i915 component framework to register for hotplug
notification.
In the hotplug notification, driver reads pin sense and ELD by
sending PIN_SENSE and ELD verbs over HDA bus. Once it identifies
valid pin sense and valid ELD, store the ELD into the
corresponding pin map buffer.
Also read the monitor present sense during resume and ignore the
ELD notify from graphics during PM as is done in legacy hda,
commit 8ae743e82f ("ALSA: hda - Skip ELD notification during
system suspend")
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology will also create FE DAI links dynamically from the PCM
objects. These links will be removed when the component is removed
and its topology info is unloaded.
The component driver can implement link_load/unload ops for extra
intialization (e.g. error check) and destruction.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology will create FE DAIs dynamically from the PCM objects,
and register them to the component.
A PCM topoplogy object describes a FE DAI and DAI link. Later
patch will add FE DAI links as well.
Change tplg load ops for DAI:
- Only process a DAI.
- Pass the DAI driver pointer to the component driver for
extra initialization.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 18560a4e3 (ASoC: qcom: Specify LE device
endianness).
The commit that caused us to specify LE device endianness here,
29bb45f25f (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 18560a4e3 (ASoC: qcom: Specify LE device
endianness).
The commit that caused us to specify LE device endianness here,
29bb45f25f (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the FLL is in pseudo-fractional mode there is an additional
limit on fref based on the fratio, to prevent aliasing around the
Nyquist frequency. If fref exceeds this limit the refclk divider
must be increased and the calculation tried again until a suitable
combination of fref and fratio is found or we have to fall back to
integer mode.
This patch also adds some debug log prints around this code.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Forwarding the return value of i2c_master_send, leads to errors
later on, since i2c_master_send returns the number of bytes
transmittet. Check for ret < 0 instead and return 0 otherwise.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
b4c83b171 ("ASoC: rsnd: add Multi channel support") added
Multi channel support, and current rsnd_ssi_is_multi_slave()'s check
method is !SSI equals SSIM1/2/3. But, SSI parent also hit to this macro.
Because of this reason, some stream which needs SSI parent clock
can't work correctly. This patch uses rsnd_ssi_multi_slaves() to
solve this issue. This issue was reported by Dung.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we have a path that connects to DSP sink and source, we
need to query the blob using the default params. So add a
function to query the params for such path
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While going to shutdown, we need to bring HW to clean state. This
is done by cleaning up stream descriptor registers. This cleanup
is already done by decoupling of stream and stopping the chip, so
invoke these from shutdown handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some modules require params to be set after the module is bound
to all the pins connected.
The module provider initializes set_param flag for such modules
and we send params after binding. This is done by the function
skl_tplg_set_module_bind_params()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SoC has MCLK output which is typically required by codecs.
The MCLK is controlled by DSP FW, so driver can configure that by
sending DMA_CONTROL IPC. The configuration for MCLK is present
in the endpoint blob.
So if block has this configuration, send IPC to DSP for MCLK
configuration. This is done by new function skl_dsp_set_dma_control()
which is invoked by BE prepare.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S port can be connected to multiple BE pipes, get module config
only for the active BE pipe.
This helpers helps to do that and is used in subsequent patches
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_setup_cpr_gateway_cfg() retrieves gateway settings which are
required for copier module configuration. For upcoming DMA
control IPC we need similar retrieval, so separate this piece into
skl_get_node_id() helper which will be common for these functions
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Delay check was using ternary operator, it can be simplified to
simple if condition, so update it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The match module lacked module license and description, so add it
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM driver is recommended for BYT, CHT based platforms, so if
CONFIG_SND_SST_IPC_ACPI is selected then don't compile the BYT
Device IDs in common ACPI driver to avoid probe conflicts.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI match module is common to all three drivers, HSW, SKL
and Atom-DPCM driver. But Atom-DPCM driver does not use common
sst code so we cannot include the common SST module in Atom-DPCM
driver.
So the solution is to have a independent sst-match-acpi module
which helps in matching for all the three drivers. Now all driver
can be inbuilt in a single image
This patch really fixes the regression introduced by the
commit 95f0980148 ("ASoC: Intel: Move apci find machine routines")
Acked-by: Jie Yang <yang.jie@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit dc901a3541 ("ASoC: Intel: fix ACPI probe
regression with Atom DPCM driver") as the fix prevented the probe
on HSW/BDW if Atom-DPCM was selected
Acked-by: Jie Yang <yang.jie@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add cs4271 and cs42727 support for fsl-asoc-card
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If something else, typically a codec, has enabled mclk, the BUSY
bit may be set when hw_params() is called without this being an
error. This check thus causes intermittent failures to configure
the sound device when used in such a manner. Fix this by making
the test conditional on !saif->mclk_in_use.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some configurations, the dai registers get written before the bias
level is changed in the codec driver. This leads to a situation where
an initial write to the serial port register gets ignored, and future
writes may as well, since regmap thinks that the codec already holds the
value. More specifically, configuring the codec as i2s master would in
fact result in the codec running as slave, a situation where no i2s
clocks are generated and hence no data is transferred.
This change makes sure that regmap only caches writes when the core
clock is disabled, and syncs regmap whenever enabling the core clock
again.
Signed-off-by: Andreas Irestål <andire@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona CODECs support several rates that do not have simple defines
in ALSA. This patch adds support for SNDRV_PCM_RATE_KNOT so that users
can open stream at these rates. As part of this we should always set
constraints in arizona_startup, currently we only set the constraints if
we already have a clock to limit rates to that family of sample rates.
This patch updates this to set a constraint of all rates supported by
the chip if we do not already know which family of rates to limit to.
Finally we also reduce the list of rates supported in the constraints to
only include those that are supported on current parts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When playback mono wav with record in background, there will be some
nosie in the right dac channel. It seems that the ADC data has been
routed to the dac channel.
The cs42888 have 8 dac channels, it's appropriate to mute the unused
dac channels, and the noise will disappear.
Steps to reproduce this issue:
arecord -D hw:0,0 -f S16_LE -r 48000 -c 1 a.wav &
aplay -Dhw:0,0 audio48k16M.wav
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a pair of warnings when ASRC is absent in the DTB:
fsl-asoc-card sound: ASoC: no source widget found for ASRC-Playback
fsl-asoc-card sound: ASoC: Failed to add route ASRC-Playback -> direct -> CPU-Playback
fsl-asoc-card sound: ASoC: no sink widget found for ASRC-Capture
fsl-asoc-card sound: ASoC: Failed to add route CPU-Capture -> direct -> ASRC-Capture
This is because the driver is still trying to add DAPM routes for ASRC
even if it doesn't exist on that platform.
The warnings are harmless but it might be annoying. So this patch drops
the DAPM routes of ASRC when it's absent in the DAI link.
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver used autosuspend delay to delay going to D3. But per
HW recommendation we should go to D3 soon, so remove the delay
from driver
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMIC BE can have 2 or 4 channels supported. The DMIC fixup needs
to take this into account.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some modules may be directly connected to a pipeline without a
mixer module. For these modules, we require PRE_PMU and POST_PMU
handler which will do bind between the pipelines, so add these
missing handlers.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_tplg_bind_sinks() takes only the first sink widget. This
breaks in case we have multiple sinks for a module.
So pass source widget to skl_tplg_bind_sinks() and bind for all
sinks by calling this recursively
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not stop the sink pipe in it's pmd handler for a mixin
module as this module may still be connected to other pipes.
This will be stopped and freed by current implementation on last
connected pipe unbind.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For binding modules we should check if source or destination
module is in UNINT state. We canot bind even if one of them is
in this state.
So update the check from logical AND to logical OR and do not
bind modules for this case
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In unbind modules, the skl_get_queue_index() can return error
if the pin is dynamic and module is not bound yet. So instead
of returning error this check should return success as modules
is not yet bound. This will let the module be bound when connected
pipes are enabled and will bind this as well.
So change the return value to 0
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We check and allocate pipeline resources in one shot. That causes
leaks if module creation fails later as that is not freed.
So split the resource allocation into two, first check if
resources are available and then add the resources upon
successful creation. So two new functions are added for checking
and current functions are re-purposed to only add the resources
for memory and MCPS.
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While cleaning resources on module pmd event, we check for return
of skl_unbind_modules(). On failure this causes leak as all modules
attached do not have resources freed.
So ignore return value of module unbind and continue freeing
resources. This makes dapm state and resources correct.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When delay reported by HW is equal to buffersize, it means the
value is wrapped so we should report as 0. So add the condition
to check this while reporting the delay from LPIB.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV buffer can be smaller than the module data, so update the
size of data to be copied before doing the copy.
Also TLV header consists of two unsigned ints, this is also taken
into account here and size modified to reflect this
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a DAPM context has a prefix the autodisable widgets get prefixed
twice, once for the control and once for the widget. To avoid this use
the un-prefixed control name to construct the autodisable widget name.
This change is purely cosmetic.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for rt5514. The codec includes a low power
DSP for voice wake up. The register address is incremental by 4 in the DSP
memory map. In order to recover the codec settings in the codec mode and
manipulate the DSP mode for voice wake up, we use the multi-level register
map. One is for ALSA API in codec mode that can be recovered by cache
before recording. Another is for DSP related settings that can be accessed
with 32bit address of the DSP in the application of voice wake up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a106804 ("ASoC: compress: Fix compress device direction check")
added a dependency on the compress-cpu-dai channel_min field
which was removed earlier by commit 77095796
("ASoC: Intel: Atom: clean-up compressed DAI definition")
as part of the baytrail cleanups.
The net result was a regression at probe on all Atom platforms
with no sound card created.
Fix by adding explicit initialization for channel_min to 1
for the compress-cpu-dai.
Reported-by: Tobias Mädel <alsa-devel@tbspace.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should return a valid sample rate from the pointer callback, this
patch adds this into the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While performing hw_free, DPCM checks the BE state but leaves out
the suspend state. The suspend state needs to be checked as well,
as we might be suspended and then usermode closes rather than
resuming the audio stream.
This was found by a stress testing of system with playback in
loop and killed after few seconds running in background and second
script running suspend-resume test in loop
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In the case that the driver is configured from device-tree
i2s_reg_comp1 and i2s_reg_comp2 aren't initialised, breaking the driver.
Fix this by unconditionally setting these values before checking for quirks.
Fixes: a242cac1d3 ("ASoC: dwc: add quirk to override COMP_PARAM_1 register")
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds firmware compressed stream capture support
and DAI hookups for voice control firmware (based on the wm5110
implementation.)
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm5102 also supports the audio trace firmware, this patch adds support
for this into the wm5102 driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mainly this adds DAI links for the audio trace, however, it is also
necessary to update the data IRQ handler to check more cores. We have
the handler check every core so it should not be necessary to update
this function if more compressed firmwares are added in the future.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reference the TRM, the ALC5616 support one 24bit/8KHz ~ 192KHz
I2S/PCM Interface for stereo DAC and stereo ADC.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DPCM doesn't copy dpcm->hw_params and doesn't call be_hw_params
if some FE are connected. But 2nd or later FE might want to know BE hw_params.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM179x family supports both SPI and I2C. This patch adds support
for the I2C interface.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pcm179x family supports both SPI and I2C for configuration. This
patch splits the driver into core and SPI parts, in preparation for
I2C support.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADSP code should be agnostic of which CODEC it runs upon, currently
there is only one remaining part of the implementation that doesn't
follow this. When the DSP is booted on ADSP2 we read
ARIZONA_SYSTEM_CLOCK_1 and use that to set the initial speed for the DSP
clock. This patch factors that out into CODEC specific code, leaving the
ADSP code entirely CODEC agnostic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio trace firmware allows the capture of arbitrary streams of
audio from the DSP and commonly used for debugging other firmwares. This
patch adds support for this firwmare into the ADSP driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The region definition will be shared by most firmwares so give this a
more generic name and whilst we are there improve the naming of the
voice control capabilities array as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst there is nothing wrong with the error path here it looks a little
bit odd, this patches makes the code a little more idiomatic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the code to enable the clock to the CODEC driver
if it needs the clock enabled.
In some case, We need to claim the clock which is driving the codec
so that when we enable clock gating, we continue to clock the codec
when needed.
if mclk provided, to enable and disable the clock source.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch try to fix the trivial typo.
Run "scripts/checkpatch.pl -f --subjective xxx"
The enable more subjective tests.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit e22579713a ("ASoC: simple card: set cpu-dai sysclk
with mclk-fs") added sysclk / SND_SOC_CLOCK_OUT setting, that makes
asoc_simple_card_hw_params fail if the operation is not supported,
although the intention clearly was to ignore ENOTSUPP. Fix it.
The patch fixes audio playback on Kirkwood / OpenRD client,
where the following errors are seen:
asoc-simple-card sound: ASoC: machine hw_params failed: -524
alsa-lib: /alsa-lib-1.0.28/src/pcm/pcm_hw.c:327:(snd_pcm_hw_hw_params) SNDRV_PCM_IOCTL_HW_PARAMS failed (-524): Unknown error 524
Fixes: e22579713a ("ASoC: simple card: set cpu-dai sysclk with mclk-fs")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
An older patch to convert the API in the s3c i2s driver
ended up passing a const pointer into a function that takes
a non-const pointer, so we now get a warning:
sound/soc/samsung/s3c2412-i2s.c: In function 's3c2412_iis_dev_probe':
sound/soc/samsung/s3c2412-i2s.c:172:9: error: passing argument 3 of 's3c_i2sv2_register_component' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
However, the s3c_i2sv2_register_component() function again
passes the pointer into another function taking a const, so
we just need to change its prototype.
Fixes: eca3b01d08 ("ASoC: switch over to use snd_soc_register_component() on s3c i2s")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SND_SOC_INNO_RK3036 is enabled but REGMAP_MMIO is not, the MODPOST
step fails with this error:
...
Kernel: arch/x86/boot/bzImage is ready (#3)
Building modules, stage 2.
MODPOST 3203 modules
ERROR: "__devm_regmap_init_mmio_clk" [sound/soc/codecs/snd-soc-inno-rk3036.ko] undefined!
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the ssm4567 is powered up the driver calles regcache_sync() to restore
the register map content. regcache_sync() assumes that the device is in its
power-on reset state. Make sure that this is the case by explicitly
resetting the ssm4567 register map before calling regcache_sync() otherwise
we might end up with a incorrect register map which leads to undefined
behaviour.
One such undefined behaviour was observed when returning from system
suspend while a playback stream is active, in that case the ssm4567 was
kept muted after resume.
Fixes: 1ee44ce030 ("ASoC: ssm4567: Add driver for Analog Devices SSM4567 amplifier")
Reported-by: Harsha Priya <harshapriya.n@intel.com>
Tested-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_prepare() call in hw_params() has no matching clk_unprepare(),
leaving the clk with an ever-increasing prepare count. Moreover,
hw_params() can be called multiple times which would again leave us
with a runaway prepare count. Fix this by moving the clk_prepare()
call to the startup() function and adding a shutdown() function with
a matching clk_unprepare() as these operations are already correctly
bracketed by soc-core.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The in-driver clock reparenting had been added when we did not had other
means to cleanly set the parent for the fck. Now we can use
assigned-clocks/assigned-clock-parents in DT binding. Print warning when
the fck_parent is present for McASP and recommend the switch to the proper
way to handle the clock selection.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has .init/.start/.stop/.quit callbacks,
and it needs many IPs (SRC/CTU/MUX/DVC/CMD/SSIU/SSI).
Because of these relationship, it might get unnecessary
error IRQ when start/stop.
This patch adds new .irq callback and control IRQ enable/disable
timing to avoid it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound needs recovery (= restart) when under/over run
error occurred, and current driver tries it on under/over run error
handler automatically. But this recovery should be handled by userland,
not kernel. This patch stops XRUN when under/over run error occur, and
will leave the recovery of HW in userland.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When registering a ASoC card the driver data of the parent device is set to
point to the card. This driver data is used in the
snd_soc_suspend()/resume() callbacks.
The imx-spdif driver overwrites the driver data with custom data which
causes snd_soc_suspend() to crash. Since the custom driver is not used
anywhere simply deleting the line which sets the custom driver data fixes
the issue.
Fixes: 43ac946922 ("ASoC: imx-spdif: add snd_soc_pm_ops for spdif machine driver")
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a set_sysclk() DAI op so the card driver can set the
input clock frequency. If this is done, the pll and mclk divider
are configured to produce the required 256x fs clock when the
sample rate is set by hw_params().
These additions make the codec work with the simple-card driver.
Card drivers calling set_pll() and set_clkdiv() directly are
unaffected.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use shiny new acpi_dev_present() and remove all the boilerplate
to search for a particular ACPI device. No functional change.
Cf. 2d12b6b381 ("ACPI / utils: Add acpi_dev_present()").
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no guarantee that on fsl_ssi module load
SSI registers will have their power-on-reset values.
In fact, if the driver is reloaded the values in
registers will be whatever they were set to previously.
However, the cache needs to be fully populated at probe
time to avoid non-atomic allocations during register
access.
Special case here is imx21-class SSI, since
according to datasheet it don't have SACC{ST,EN,DIS}
regs.
This fixes hard lockup on fsl_ssi module reload,
at least in AC'97 mode.
Fixes: 05cf237972 ("ASoC: fsl_ssi: Add driver suspend and resume to support MEGA Fast")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b761bf272b ("ASoC: rsnd: disable SRC.out only when stop timing")
disabled SRC.out/in in different timing, but was based on
picky HW information. Now, we have confirmed that we can disable
both in the same time. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current CTU settings was rough. This patch makes it match to datasheet.
But do nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI/SRC will try to attach DMAC as Audio-DMAC or Audio-DMAC-periperi.
It is fixed IP, but will be attached to each streams as different module
in case of MUX (= multi sound path will be merged).
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will be used as normal SSI or as clock parent SSI. Therefor,
rsnd driver wants to control SSI and parent SSI separately. Otherwise it
can't use Playback/Capture in the same time.
And it has been done by c2dc47d5cf("ASoC: rsnd: rsnd_dai_stream has each
mod's status insted of rsnd_mod") before.
OTOH, rsnd driver doesn't want to control CTU/MUX/DVC/SSIU/SSI in
separately. Otherwise, these will be re-initialized during playing if
MUX merges 2 sounds.
Because of these picky reasons, this patch re-defines status on each mod,
and add new parent_ssi_status on rsnd_dai_stream.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To select CMD data patch, it should use correct SRC from each stream
in MUX case. But current code is selecting SRC from fixed stream.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_cmd_init() overwrites "io" which will be used end of this
function. This patch solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CTU/MUX/DVC/SSIU/SSI/Audio-DMAC-periperi might be used under multipath.
So, probe()/remove() need to be called multiple times.
This patch allows it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system uses CTU/MUX, CTU/MUX/DVC will try to connect same CMD to
system, but it is not error in this case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system uses CTU/MUX, and if probe error happened, it will try to
call rsnd_dai_call(remove, ...). Then, MUX/DVC/SSIU/SSI might be called
without calling rsnd_dai_call(probe, ...). Then, each mod status might
be un-matched. It doesn't call un-matched remove function by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_call() tries to call each IP's relevant function. But it is
difficult to understand which function returned error.
This patch adds debug message for this purpose
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ADG doesn't use rsnd_mod_init(), but this limitation is no
longer necessary. Let's use common rsnd_mod_init()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since msleep() will sleep longer than intended time for values less
than 20ms, this patch allows the use of usleep_range for just 1ms.
usleep_range is a finer precision implementation of msleep and is
designed to be a drop-in replacement for udelay where a precise
sleep/busy-wait is unnecessary.
More details see Documentation/timers/timers-howto.txt.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since msleep() will sleep longer than intended time for values less
than 20ms, this patch allows the use of usleep_range for just 1ms.
usleep_range is a finer precision implementation of msleep and is
designed to be a drop-in replacement for udelay where a precise
sleep/busy-wait is unnecessary.
More details see Documentation/timers/timers-howto.txt.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'break' here is not useful after 'return' or 'goto'.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the introduction of WM8960_SYSCLK_AUTO mode, WM8960_SYSCLK_PLL mode was
made unusable. Ensure we're not PLL mode before trying to use MCLK.
Fixes: 3176bf2d7c ("ASoC: wm8960: update pll and clock setting function")
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
INBMIX1 controls LINPUTs and INBMIX2 controls RINPUTs, so fix the naming
accordingly.
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was not unregistering the compressed platform in
wm5110_remove(). If the codec is built as a module, this would
lead to a NULL pointer deref if the module was unloaded and then
re-probed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If snd_soc_tplg_component_load() fails we just printed an error message
and returned the error code but we missed releasing the firmware.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added rt5659 codec driver unconditionally defines an
ACPI device match table but then uses ACPI_PTR() to remove the
only reference to it, so we get a harmless build warning:
sound/soc/codecs/rt5659.c:4200:30: warning: 'rt5659_acpi_match' defined but not used [-Wunused-variable]
static struct acpi_device_id rt5659_acpi_match[] = {
This changes both the OF match table and the ACPI match table
to follow the same style, using ACPI_PTR/of_match_ptr to
make the reference conditional, and using an #ifdef to hide
the table. This also adds the missing MODULE_DEVICE_TABLE for
the OF case and adapts the formatting to the same style.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The shift bit of IN1 boost gain control is 12.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
RT286_CBJ_CTRL1(0x4f) bit 10 is needed for headset capture. It
will be turned off when "VREF" widget is on and be turned on when
bias level is ON. It is odd. And if "VREF" is turned on in bias
level is ON, RT286_CBJ_CTRL1(0x4f) bit 10 will be turned off.
This patch move the bit control from rt286_set_bias_level and
rt298_vref_event to rt286_jack_detect. So it will be turned on
once a jack is plugged in.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
The newly added mediatek drivers for mt8173 select codes that depend
on I2C, which cuases a build failure if I2C is disabled:
warning: (SND_SOC_ADAU1761_I2C && SND_SOC_ADAU1781_I2C && SND_SOC_ADAU1977_I2C && SND_SOC_RT5677 && EXTCON_MAX14577 && EXTCON_MAX77693 && EXTCON_MAX77843 && BMC150_ACCEL_I2C && BMG160_I2C) selects REGMAP_I2C which has unmet direct dependencies (I2C)
codecs/rt5645.c:3854:1: warning: data definition has no type or storage class
codecs/rt5645.c:3854:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
codecs/rt5677.c:5270:1: warning: data definition has no type or storage class
77_i2c_driver);
codecs/rt5677.c:5270:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
This adds an explicit dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the move to the new clock framework with commit 94cb7f76ca
("ARM: bcm2835: Switch to using the new clock driver support.")
this driver was no longer functional as it was manipulating the
clock registers locally without going true the framework.
This patch moves to use the new clock framework and also
moves away from the hardcoded address offsets for DMA getting
the dma-address directly from the device tree.
Note that the optimal bclk_ratio selection to avoid jitter
due to the use of fractional dividers, which is in the
current version has been removed, because not all devices
support these non power of 2 sized transfers, which resulted
in lots of (downstream) modules that use:
snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If platform is embedded with memory more than 3GB, the address will
go out of the scope that 32-bit can handle with. This patch sets the
dma_mask and MSB properly to describe its address to 33-bit.
Signed-off-by: Hidalgo Huang <hidalgo.huang@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module. The rt5659->i2c is no longer used after this conversion, thus
remove it as well.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static checkers complain if we don't free "adata" before returning.
Fixes: 7c31335a03 ('ASoC: AMD: add AMD ASoC ACP 2.x DMA driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bunch more updates for v4.5, mainly driver work:
- More topology API enhancements from Mengdong Lin working towards
making everything more component based and being able to specify PCM
links via topology.
- Large sets driver updates from Cirrus, Intel (mainly more Skylake
support) and Renesas.
- New drivers for AMD ACP, Atmel PDMIC, Dialog DA7218, Imagination
Technologies SoC IPs, Rockchip RK3036 Inno CODEC and Texas Instruments
PCM3168A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWk8EUAAoJECTWi3JdVIfQ+RwH/jid388X6x6YOa84Rs7InrIS
m2rVdjDAMAbK+smhalHzvLOGnHjpygegwZ/9/1DUiSPbcXdqMkzLoaweeVUXhu27
9G3zT0Xz1XVn/+5029oIlrsyPCtM5O9PlPOO7tiQSTBADjvl+I4hl6FHZ1LGT7Sr
tiOTAiOmIisELBzBF0L7fB18iBgE3VqkhG8obrMiTXVWgfZuRJL7kdH2WuHYFXpM
JxBcy9VrCp0JHxg+qCD7xYyFdKLE6eP96gpLi94JBqW8I3wrwmEmUqNKs+r8I7Vj
bh5/v6A2V0EaJWCKzWBARHE7BR3E2uJeoD0PcY59Kn7BKhKPjTe99g2ngTk1hIU=
=BvEm
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Last updates for v4.5
A bunch more updates for v4.5, mainly driver work:
- More topology API enhancements from Mengdong Lin working towards
making everything more component based and being able to specify PCM
links via topology.
- Large sets driver updates from Cirrus, Intel (mainly more Skylake
support) and Renesas.
- New driver for AMD ACP
- Rename PCM1792a driver to be generic pcm179x
dev pointer in struct snd_soc_pcm_runtime does not have dma_ops set. In
v4.4 kernel dma_ops would end up pointing to dummy_dma_ops in such cases.
So attempting to use such device in allocating coherent memory on aarch64
would fail.
According to commit 1dccb598df ("arm64:
simplify dma_get_ops") The current behavior of dma_get_ops is to fall
back to the global dma_ops when a device has not set its own dma_ops,
but only for DT based systems.
So, this patch fixes the driver to use correct device pointer while
allocating coherent memory, and also deletes un-necessary dma_mask setup
on soc_runtime->dev.
Without this patch lpass driver would fail with below log:
...
[ 6.541542] ADV7533: lpass_platform_alloc_buffer: Could not allocate DMA buffer
[ 6.541914] apq8016-lpass-cpu 7708000.lpass-cpu: ASoC: pcm constructor failed: -12
[ 6.548216] qcom-apq8016-sbc 7702000.sound: ASoC: can't create pcm ADV7533 :-12
[ 6.555581] qcom-apq8016-sbc 7702000.sound: ASoC: failed to instantiate card -12
[ 6.566072] qcom-apq8016-sbc: probe of 7702000.sound failed with error -12
...
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
