There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the cy8ctmg110_ts driver over.
Compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the migor_ts driver over.
Compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the mcs5000_ts driver over.
Compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the eeti_ts driver over.
Compile tested only by me, but Sven Neumann reports that the new code
works.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the ad7879-ts I2C support over.
Compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Not all penabled devices support touch. The same holds true for touch
devices, so we should be setting up devices according to the results
returned when we query the hardware.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
The drivers using the type B protocol all report tracking information
the same way. The contact id is semantically equivalent to
ABS_MT_SLOT, and the handling of ABS_MT_TRACKING_ID only complicates
the driver. The situation can be improved upon by providing a common
pointer emulation code, thereby removing the need for the tracking id
in the driver. This patch moves all tracking event handling over to
the input core, simplifying both the existing drivers and the ones
currently in preparation.
Acked-by: Ping Cheng <pingc@wacom.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The MT slots devices all follow the same initialization pattern
of creating slots and hinting about buffer size. Let drivers call
an initialization function instead, and make sure it can be called
repeatedly without side effects.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
In preparation for common code to handle a larger set of MT slots
devices, move the slots handling over to a separate file.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
This patch introduces support for Sitronix ST1232 integrated capacitive
touchscreen with LCD module. The touchscreen is multitouch capable and
can report coordinates of up to two contact points.
Signed-off-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
I've recently got my hands on a LG Flatron T1710B touchscreen.
As other LG products, this seems to use the ITM panel.
Signed-off-by: Glenn Sommer <gsommer@datanordisk.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The kcalloc call for the object table is using sizeof(struct qt602240_data)
when it should be using sizeof(struct qt6602240_object), resulting in a larger
allocation than is required.
Signed-off-by: Chris Leech <christopher.leech@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: appletouch - remove extra KERN_DEBUG use from dprintk
Input: bu21013_ts - fix null dereference in error handling
Input: ad7879 - prevent invalid finger data reports
Considering following scenario - the touch is present on the screen
at the beginning of the last conversion sequence, but by the time
the last sequence is finished, the finger is lift off. The AD7879 data
available interrupt signals (DAV) completion, however some X,Y values
are not valid because the screen inputs were floating during the
acquisition.
The AD7877 acts differently here, since it only asserts DAV if the
touch is still present when the conversion sequence finished.
Based on the fact that this can only happen in the last sample of the
repeated conversion sequence, we simply skip the last (short glitches
are filtered by the AD7879 internal median and average filters).
This doesn't cause noticeable side effects, since the minimum conversion
interval is 9.44ms. We receive ~100 waypoint samples per second, so we
simply delay the result by 9.44ms.
We also reject samples where pressure is greater than pressure_max.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
Instead of using asynchronous SPI API and then spinning waiting for SPI
transfer to complete when disabling the device, let's use threaded IRQ
model and spi_sync().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of manually creating one set of attributes or another set up
is_visible method in attribute group structure to control whether
aux3 or gpio3 attribute is presented to userspace.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Suppress events where pressure > pressure_max.
These events come typically along with inaccurate X and Y samples.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some input users such as Android or X require BTN_TOUCH events.
Implement EV_KEY:BTN_TOUCH and make sure that the release event
is not erroneous scheduled without a preceding valid touch.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
According to the AD7877 datasheet:
Each transfer operation is 16-bit. If multiple read/write operations are
to be performed, CS must be taken high after the end of each read/write
operation before another read/write operation can be performed by
taking CS low again.
Make sure CS toggles after each transfer in the message.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make hp680_ts_init/exit() call cancel_delayed_work_sync() instead of
calling cancel_delayed_work() followed by flush_scheduled_work().
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 9114337 introduces regulator operations in ads7846 touchscreen
driver. Among these operations, some are called while holding a
spinlock. On many platforms regulators reside on slow buses, such as
I2C/SPI and require sleep while accessing them.
The touchscreen itself is also a SPI device and currently relies on
asynchronous SPI access to avoid sleeping in interrupt context. Let's
switch to using threaded IRQ to be able to access SPI bus
synchronously (which simplifies driver a bit); it also allows safe
access to the regulators as well.
This has been tested on the ti_omap3530evm board:
1) using ts_lib after normal boot
2) using ts_lib after "#echo 1/0 > /sys/bus/spi/devices/spi0.1/disable"
3) using ts_lib after "#echo mem > /sys/power/state" and "wake up"
Also tested on pandora.
Based on original patch by Dmitry Torokhov.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Without this the jitter on the touchscreen makes it hard to use for
most GUI toolkits.
Signed-off-by: James Ketrenos<jketreno@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add logic to wm97xx_read_aux_adc() to retry reading the adc if the
sample failed. This could occur if the previous sample was still in
the return register or the sample timed-out. Also avoid a pathologic
failure mode by disabling the digitizer and returning -EBUSY after 5
retries.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use platform_device_del() instead of platform_device_unregister() in error
handling path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensoruce.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It is forbidden to call input_free_device() after input_unregister_device().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Once device is registered we should call input_unregister_device()
instead of input_free_device().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We call platform_get_drvdata() in tps6507x_ts_remove(),
thus we should call platform_set_drvdata() in tps6507x_ts_probe().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use input_free_device() to free devices that have not been registered.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver is in reasonable shape now so let's move it out of staging.
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch set introduces support for the LPC32xx touchscreen
controller driver. The LPC32xx touchscreen controller supports
automated event detection and X/Y data conversion for resistive
touchscreens.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Durgesh Pattamatta <durgesh.pattamatta@nxp.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some serial wacom devices support two-finger touch. Test for this during
init and parse the touch packets accordingly. Touch packets are
processed using Protocol B (MT Slots).
Note: there are several wacom versions that do touch but not two-finger
touch. These are not catered for here, touch events for these are simply
discarded.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Tablets that support touch input may report different sized packages,
depending on the touch sensor in the tablet. For now, discard the
packages until we report them as touch input proper.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The protocol used by the w8001 supports status fields for tip, side
switch and eraser as well as a RDY field for proximity.
The protocol has a double usage for the f2 bit in the packet. If set,
the data is either pen + side2 button or eraser. Assume eraser if the
device comes into proximity with the f2 bit set, otherwise trigger the
side2 button. If the device comes into proximity with the f2 bit and
that bit disappears afterwards, fake proximity out for the eraser and
proximity in for the pen.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
platform_get_irq_byname() can return negative results, it is not seen to
unsigned ts_irq. Make it signed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-By: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This one adds a driver for STMPE touchscreen controllers.
This driver depends on the stmpexxx mfd core driver.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
"ret" should be signed here or the error handling doesn't work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the cy8ctmg110 capacitive touchscreen used on some
embedded devices.
(Some clean up by Alan Cox)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
No need to take address, w90p910_ts is already a pointer.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This implements reset_resume() by splitting init into allocations
of private data structures and device initializations. Device
initializations are repeated upon reset_resume.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This implement USB autosuspend while the device is opened for
devices that do remote wakeup with a fallback to open/close for
those devices that don't. Devices that require the host to
constantly poll them are never autosuspended.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This implements basic support for suspend & resume.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The chip's full name is AT42QT602240 or ATMXT224. This is a capacitive
touchscreen supporting 10-contact multitouch and using I2C interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ADS7845 is a controller for 5-wire touch screens and somewhat
different from 7846. It requires three serial communications to
accomplish one complete conversion. Unlike 7846 it doesn't allow
Z1-/Z2- position measurement.
The patch extends the ads7846 driver to also support ads7845.
The packet struct is extended to contain needed command and
conversion buffers. ads7846_rx() and ads7846_rx_val() now
differentiate between 7845 and 7846 case. ads7846_probe() is
modified to setup ads7845 specific command and conversion
messages and to switch ads7845 into power-down mode, since
this is needed to be prepared to respond to pendown interrupts.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some input events users such as Android require BTN_TOUCH events.
Implement EV_KEY/BTN_TOUCH and make sure that the release event
is not erroneous scheduled without a preceding valid touch.
Avoid duplicated BTN_TOUCH events, even though input core filters
them.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The ad7879 driver is using the old bus method of only supporting one
at a time (I2C or SPI). So refactor it like the other input drivers
that support multiple busses simultaneously.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the ET&T TC4UM 4-wire USB touchscreen
controller and tries to reuse the bits for TC5UH controller in kernel
already. Data interface is same.
Tested-by: Roger Pueyo Centelles <rogerpueyo@rogerpueyo.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On some platforms, for example with GPIO interrupts on mpc5121,
it is not possible to configure falling edge interrupts.
Specifying irq trigger type in platform data structure
allows using ads7846 driver on such platforms.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Stanse found that tsc is dereferenced earlier than checked for being
NULL in tps6507x_ts_remove. Remove the test because there is no way
for tsc to be NULL there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Let's perform be16_to_cpu() conversions once for each received packet,
and then use cached values. Makes code a little bit easier to follow.
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With no word size given in the users platform data, a generic spi host
controller driver will assume a default word size of eight bit. This
causes transmission to be performed bytewise, which will fail on little
endian machines for sure. Failure on big endian depends on usage
of slave select to mark word boundaries.
Anyway, ad7877 is specified to work with 16 bit per word, so
unconditionally set the word size accordingly. Flag an error where 16
bit per word is not available.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oliver Schneidewind <osw@emlix.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch fixes the follwing warning introduced by commit
067fb2f648 ("Input: ads7846 - return error on
regulator_get() failure"):
drivers/input/touchscreen/ads7846.c: In function 'ads7846_probe':
drivers/input/touchscreen/ads7846.c:1167: warning: format '%ld' expects
type 'long int', but argument 4 has type 'int'
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1) Use msecs_to_jiffies() instead of calculating by hand.
2) Call cancel_delayed_work_sync() instead of cancel_delayed_work()
followed by a separate flush_workqueue().
3) Remove the "tsc->wq = 0;" Sparse complains about that because
tsc->wq is a pointer, not an int. It's not needed because we just
free the pointer anyway.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The S3C touchscreen driver is logging at LOG_INFO on every stylus up
event which spams the console needlessly. Reduce the priority of the
message to debug level for some peace and quiet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The name of the Kconfig symbol for the ADC has changed as a result of
application to more SoCs but the select statement has not been updated,
causing linker failures as the ADC core has not been built.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add touch screen input driver for TPS6507x family of multi-function
chips. Uses the TPS6507x MFD driver. No interrupt support due to
testing limitations of current hardware.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: usbtouchscreen - support bigger iNexio touchscreens
Input: ads7846 - return error on regulator_get() failure
Input: twl4030-vibra - correct the power down sequence
Input: enable onkey driver of max8925
Input: use ABS_CNT rather than (ABS_MAX + 1)
Bigger Nexio touchscreens not only send more data but also the header
values are modified somewhat. Fix the header (it's a guesswork but
it works at least on one 46" touchscreen with 2.00SMS firmware) and
also increase rept_size.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In probe(), if regulator_get() failed, an error code was not being
returned causing the driver to be successfully bound, even though
probe failed. This in turn caused the suspend, resume and remove
methods to be registered and accessed via the SPI core. Since these
functions all access private driver data using pointers that had been
freed during the failed probe, this would lead to unpredictable
behavior.
This patch ensures that probe() returns an error code in this failure
case so the driver is not bound.
Found using lockdep and noticing the lock used in the suspend/resum
path pointed to a bogus lock due to the freed memory.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For more clearance what the functions actually do,
usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()
They should only be used in code which really needs DMA coherency.
All call sites have been changed accordingly, except for staging
drivers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (224 commits)
ARM: remove 'select GENERIC_TIME'
ARM: 6136/1: ARCH_REQUIRE_GPIOLIB selects GENERIC_GPIO
ARM: 6074/1: oprofile: convert from sysdev to platform device
ARM: 6073/1: oprofile: remove old files and update KConfig
ARM: 6072/1: oprofile: use perf-events framework as backend
ARM: 6071/1: perf-events: allow modules to query the number of hardware counters
ARM: 6070/1: perf-events: add support for xscale PMUs
ARM: 6069/1: perf-events: use numeric ID to identify PMU
ARM: 6064/1: pmu: register IRQs at runtime
ARM: Optionally allow ARMv6 to use 'normal, bufferable' memory for DMA
ARM: 6134/1: Handle instruction cache maintenance fault properly
ARM: nwfpe: allow debugging output to be configured at runtime
ARM: rename mach_cpu_disable() to platform_cpu_disable()
ARM: 6132/1: PL330: Add common core driver
ARM: 6094/1: Extend cache-l2x0 to support the 16-way PL310
ARM: Move memory mapping into mmu.c
ARM: Ensure meminfo is sorted prior to sanity_check_meminfo
ARM: Remove useless linux/bootmem.h includes
ARM: convert /proc/cpu/aligment to seq_file
arm: use asm-generic/scatterlist.h
...
Use kmemdup when some other buffer is immediately copied into the
allocated region.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make the driver depend on either ARCH_S3C2410 (as legacy) or the new
device selection of SAMSUNG_DEV_TS.
Change the menuconfig name to reflect this driver is now handling more
devices that just the s3c2410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a feature bit field in the touchscreen driver for Samsung SoCs.
Which can be used to distinguish the TSADC module features.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: minor fix to title]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
This patch implements generic GPIO configuration function in Samsung
touchscreen driver. And makes the touchscreen driver s3c24xx-ts.c
generic to all the Samsung SoCs.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ben-linux@fluff.org: fixed title ]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
