[Why]
The link encoder assignment leaves the old stream data when it was
unassigned. When the clear encoder assignment is called, it based on the
old stale data to access the de-allocated stream.
[How]
There should be no need to explicitly clean up the link encoder
assignment if the unassign loop does the work properly, the loop should
base on the current state to clean up the assignment.
Also, the unassignment should better clean up the values in the
assignement slots as well.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Roy Chan <roy.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
According to eDP spec, DPCD 1.3 is only for eDP DPCD v1.4
In dpcd_set_link_settings function, the driver is just above v1.3
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: ChiawenHuang <chiawen.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
reduce az indirect register dump. need add az clock_gating control field
used in some project.
[how]
conditional output indrect register in the log. add clock_gating feild
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A built firmware binary may be aligned to 16-bytes with padding at the
end as necessary. In the case that padding was applied the meta info
will not be detected correctly and we won't be able to allocate the
appropriate firmware and tracebuffer sizes.
[How]
To maintain compatibility with already released firmware where this
occurs we need to try every meta offset from 0..15 inclusive.
Extract out the meta info checker into a helper function that's called
for each of these offsets and exit early when we've found it.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The link_enc_cfg API operates in one of two modes depending on the stage
of application of dc_state to hardware. The API is the safest way to
query link encoder assignments.
[How]
Use results of link encoder assignment query using link_enc_cfg API.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
With RGB MPO enabled, playing a video with multiple displays connected
results in underflow when closing the video window
[HOW]
Reverted the old change to fix this problem, which prevented pipe splits
for multiple display configurations and caused high MCLK speeds during
idle. Added a two step call to dc_update_planes_and_stream, first time
with pipe split disabled and the second time with pipe split enabled,
which fixed the underflow issue
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Angus Wang <angus.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
matching the dmcub_support with all other dcn version.
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
PSR set power command wasn't setting panel instance
and command version which caused both streams
to overwrite the same PSR state.
[how]
Pass panel instance to the set power command function
and to DMUB and set command version enum
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. The code to blank all dp display have been called many times,
so add helpers in dc_link to make it more concise.
2. Add some check to fix the dmesg errors at boot and resume from S3
on dcn3.1 during DQE's promotion test.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since the variables named is_end_of_payload and hpd_status are already
bool type, the ?: conditional operator is unnecessary any more.
Clean them up here.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF/AjYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1hkIAJ6sFDbvb4M4LMwf
Slh2NVL9o5sLMBDzVwnVlyMSKDbMn1WBKreGssaLgZjGDc74lxsdSmw5l9MZm0JN
xlq95Q6XFiuu+0qDHPWwfDz3JFO4TqW2ZLLPWk9NnkNbRXqccSrlVRi1RpgE1t3/
NUtS8CQLu6A2BYMc6mkk3aV6IwSNKOkWbM5eBHSvU4j8B6lLbNQop0AfO/wyY1xB
U6LiVE1RpN/b7Yv+75ITtNzuHzVIBx6305FvSnOlKbMKKvIClt96Vd2OeuoEkK+6
wGU8JraB1+fc0GckAhynNrjWQWdvi0MAhFWWEJxjS20OGcV1rXDduNfkVNauO1Zn
+dNyJ3s=
=g9fz
-----END PGP SIGNATURE-----
BackMerge tag 'v5.15' into drm-next
I got a drm-fixes which had some 5.15 stuff in it, so to avoid
the mess just backmerge here.
Linux 5.15
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Why]
Video plane gets rejected for non-zero src_y and src_x on DCN2.x.
[How]
Limit the rejection till DCN1.x and verified MPO, by dragging video
playback beyond display's left (0, 0) co-ordinates.
Fixes: d89f6048bd ("drm/amd/display: Reject non-zero src_y and src_x for video planes")
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need HPD IRQ notifications (RX, short pulse) to properly handle
DP MST for DPIA connections.
[How]
A null pointer exception currently occurs when these are received
so add a check to validate that we have a handler installed for
the notification.
Extend the HPD handler to also handle HPD IRQ (RX) since the logic is
the same.
Fixes: e27c41d5b0 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Jude Shih <shenshih@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Per DRM spec we only need to hold that lock when touching
connector->state - which we do not do in that handler.
Taking this locking introduces unnecessary dependencies with other
threads which is bad for performance and opens up the potential for
a deadlock since there are multiple locks being held at once.
[How]
Remove the connection_mutex lock/unlock routine and just iterate over
the drm connectors normally. The iter helpers implicitly lock the
connection list so this is safe to do.
DC link access also does not need to be guarded since the link
table is static at creation - we don't dynamically add or remove links,
just streams.
Fixes: e27c41d5b0 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Reviewed-by: Jude Shih <shenshih@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Trivial patch which adds a comment for macro
endif's in amdgpu_dm.c
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
make action upon failure in "drm_atomic_add_affected_connectors()"
consistent with the rest of failures in amdgpu_dm_atomic_check().
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no reason to allow for partial buffers from userspace in our
debugfs. In this particular case callers will zero out the wr_buf but if
callers in the future don't do that we might be looking at corrupt data.
Linus puts it better than I can in
https://lkml.org/lkml/2021/10/26/993
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
In order to have dc_enable_dmub_notifications() more precise, add
one more condition to check if dc->debug.dpia_debug.bits.disable_dpia
is false.
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During Z10, root clock gating and memory low power registers needs to
to be restored if optimization is enabled in driver.
[How]
Added new DMUB boot option for root clock gating and memory low power.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The MPC memory clocks should be powered down when not in use.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why&how]
write LINK_SQUARE_PATTERN_num + 1 for square pulse pattern.
Specs requirement to write this register prior to write LINK_QUAL_LANEX_SET.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
State can be cleared without removing individual streams (by
calling dc_remove_stream_from_ctx()). This can leave the
encoder assignment module in an incoherent state and cause
future assignments to be incorrect.
[How]
Clear encoder assignments when committing 0 streams or
re-initializing hardware.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In scenario when 1 display connected with pipe split (2 pipes in use)
and 3 new displays simultaneously hotplugged via MST hub (4 pipes in use),
mpcc may get reprogram to other vtg, remaining busy.
In this case waiting for mpcc idle timeouts with error like this:
[drm] REG_WAIT timeout 1us * 100000 tries - mpc2_assert_idle_mpcc
RIP: 0010:mpc2_assert_mpcc_idle_before_connect
Call Trace:
dcn20_update_mpcc
dcn20_program_front_end_for_ctx
dc_commit_state
amdgpu_dm_atomic_commit_tail
...
[How]
Add pipe split change condition to disable dangling plane.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MST monitor sends link loss short pulse continuous but sink is
occupy by HDMI input to lead link training fail.
[How]
disable link once retraining fail.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Yu-ting Shen <yu-tshen@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It was found that the system would hang on a dummy pstate when playing
4k60 videos on a 1080p 390Hz monitor.
[HOW]
Properly select the dummy_pstate_latency_ms when firmware assisted
memory clock switching is enabled instead of assuming that the highest
latency would work for every monitor timing.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Felipe Clark <felclark@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix spacing issue for the format string.
Addresses-Coverity-ID: 1446765: ("Invalid printf format string")
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If timing and bpp of displays on mst hub are not changed,
pbn, slot_num for displays should not be changed. Linux
user mode may initiate atomic_check with different display
configuration after set mode finished. This will call to
amdgpu_dm to re-compute payload, slot_num of displays and
saved to dm_connect_state. stream->timing.flags.dsc, pbn,
slot_num are updated to values which may be different from
that were used for set mode. when dsc hub with 3 4k@60hz dp
connected, 3 dsc engines are enabled. timing.flags.dsc = 1.
timing.flags.dsc are changed to 0 due to atomic check. when
dsc hub is unplugged, amdgpu driver check timing.flags.dsc
for last mode set and find out flags.dsc = 0, then does not
disable dsc.
[HOW]
check status of displays on dsc mst hubs. re-compute pbn,
slot_num, timing.flags.dsc only if there is mode, connect
or enable/disable change.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit 652de07add ("drm/amd/display: Fully switch to dmub for all dcn21
asics") switched over to using dmub on Renoir to fix Gitlab 1735, but this
implied a new dependency on newer firmware which might not be met on older
kernel versions.
Since sw_init runs before hw_init, there is an opportunity to determine
whether or not the firmware version is new to adjust the behavior.
Cc: Roman.Li@amd.com
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1772
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1735
Fixes: 652de07add ("drm/amd/display: Fully switch to dmub for all dcn21 asics")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- DPIA MST slot registers are not programmed during payload
allocation and hence MST does not work with DPIA.
- HPD RX interrupts are not handled for DPIA.
[How]
- Added inbox command to program the MST slots whenever
payload allocation happens for DPIA links.
- Added support for handling HPD RX interrupts
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CVE-2021-42327 was fixed by:
commit f23750b5b3
Author: Thelford Williams <tdwilliamsiv@gmail.com>
Date: Wed Oct 13 16:04:13 2021 -0400
drm/amdgpu: fix out of bounds write
but amdgpu_dm_debugfs.c contains more of the same issue so fix the
remaining ones.
v2:
* Add missing fix in dp_max_bpc_write (Harry Wentland)
Fixes: 918698d5c2 ("drm/amd/display: Return the number of bytes parsed than allocated")
Signed-off-by: Patrik Jakobsson <pjakobsson@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMUB binary is common for both A0 and B0. Hence, driver should
notify FW about the support for DPIA in B0.
[How]
Added dpia_supported bit in dmub_fw_boot_options and will be set
only for B0.
Assign dpia_supported to true before dm_dmub_hw_init
in B0 case.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Notify data from outbox corrupt, the notify type should be 2 (HPD) instead of 0
(No data). We copied the address instead of the value. The memory might be
freed in the end of outbox IRQ
[How]
We should allocate the memory of notify and copy the whole content from outbox to
hpd handle function
Fixes: 88f52b1fff ("drm/amd/display: Support for SET_CONFIG processing with DMUB")
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A deadlock in the kernel occurs when we fallback from the V3 to V2
add_topology_to_display or remove_topology_to_display because they
both try to acquire the dtm_mutex but recursive locking isn't
supported on mutex_lock().
[How]
Make the mutex_lock/unlock more fine grained and move them up such that
they're only required for the psp invocation itself.
Fixes: bf62221e9d ("drm/amd/display: Add DCN3.1 HDCP support")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On certain configs, SMU clock table voltages don't match which cause parser
to behave incorrectly by leaving dcfclk and socclk table entries unpopulated.
[HOW]
Currently the function that finds the corresponding clock for a given voltage
only checks for exact voltage level matches. In the case that no match gets
found, parser now falls back to searching for the max clock which meets the
requested voltage (i.e. its corresponding voltage is below requested).
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
As part of the FPU isolation work documented in
https://patchwork.freedesktop.org/series/93042/, isolate
code that uses FPU in DCN301 to DML, where all FPU code
should locate.
Cc: Christian König <christian.koenig@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Zhan Liu <Zhan.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We have a regression that cause maximize lane settings to use
uninitialized data from unused lanes.
This will cause link training to fail for 1 or 2 lanes because the lane
adjust is populated incorrectly sometimes.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
option 1: disallow different lanes to have different lane settings
option 2: dpcd lane settings will always use the same hw lane settings
even if it doesn't match requested lane adjust
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As DP features expands, we have encountered many situations where we
must configure a different DPCD lane setting from hw lane settings we
output. The change is to decouple hw lane settings from dpcd lane
settings to provide flexibility to configure dpcd and hw individually.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Decouple lane settings decision logic all to its own function. The
function takes in lane adjust array and link training settings and
decide what hw lane setting and dpcd lane setting should be used.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
revision 8 SCR requires DP Source to write TPS2 and FFE lane adjustment
in one 5 byte write aux transaction.
It specifies to read aux rd interval value as soon as we turn on TPS1
pattern.
Cc: Wayne Lin <wayne.lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To fix the check condition for fec enable for dpia links in MST mode.
[How]
dc_link_should_enable_fec() to be used to check whether fec should be
enabled in MST mode.
Cc: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To fix the check condition for fec enable for dpia links.
[How]
dc_link_should_enable_fec() to be used to check whether fec should be
enabled.
Cc: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain docks appear to NAK I2C writes to the segment pointer with the
MOT (middle of transaction) bit clear. This behaviour can cause EDID
reads from higher segments to fail.
[How]
Add workaround flag for links which connect to docks exhibiting this
issue.
Cc: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
B0 has pipe mux for DIGC and DIGD which can be connected to PHYF/PHYG or
PHYC/PHY D.
[How]
Based on chip internal hardware revision id determine it is B0 and set
DMUB scratch register so DMUBFW can connect the display pipe is
connected correctly to the dig.
Cc: Wayne Lin <wayne.lin@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hansen <Hansen.Dsouza@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
DCN303's 4 channel SOC BB causes problems at strobe
how:
workaround to manually adjust strobe calculation using FCLK
restrict.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This new DC version brings improvements in the following areas:
- Improvements for USB4;
- Isolate FPU code for DCN20, DCN301, and DSC;
- Fixes on Linking training;
- Refactoring some parts of the code, such as PSR;
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds a config flag to allow non fullscreen MPO during ODM.
Scaling calculation will still fail configurations where video is only
one one side of the screen.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
For audio packet type 0x02, there are 2 Layouts:
Layout = 0 for 2 channels
and Layout = 1 for > 2 channels.
Layout will affect bandwidth check.
Currently, for HDMI FRL, Layout field isn't set and has a default value
of 0, so theoretically only 2-channel audio for audio packet type 0x02
is supported now.
How:
1. Set Layout properly according to maximum audio channel numbers for
audios with audio packet type 0x02.
2. 8ch LPCM audio is not supported for timing modes with v_active <= 576.
Reviewed-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We found a compilation error that we thought was caused by the 3DLUT
patch; later on, we figured out the root cause of the problem, but we
already applied the revert in the wrong patch. This commit brings it
back the 3DLUT fix.
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add flag to control root clock gating in init_hw
- Add flag to indicate a diags environment is being used
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When writing long AUX commands some sinks will respond will write status
update requiring source to read status.
[How]
When a write request is replied with data (AUX_ACK_M), retry a read of
write status to determine when the write is completed.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently the naming of preferred_training_settings is ambiguous and has
caused confusion regarding its purpose and usage.
[How]
Add comment to clarify the intention.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently there are use cases that require DP link to maintain fixed VS
and PE in HW regardless of what the sink requests. BIOS integrated info
table will specify whether we need to use the fixed drive settings, and
the drive settings to use.
[How]
Implement changes to parse the integrated info table and set the fixed
drive settings accordingly.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is unnecessary in clk_mgr
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Every other CM LUT power down sequence is deferred to next vupdate as
memory powerdown updates immediately while selecting LUTs is double
buffered. Previous update to defer LUT power down missed GAMCOR and
DSCL, causing some visible flicker when entering/exiting fullscreen
video playback.
[HOW]
Update dpp deferred update loop to check for valid DPPs in res_pool
instead of referencing dcn_ip which turns out to not be populated during
runtime. Move GAMCOR and DSCL powerdown to dpp deferred updates.
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c memory doesn't get set to light sleep on hw init as intended
[HOW]
Set i2c to light sleep after reg gets zeroed, ensuring memory power
control doesn't get disabled for any other DIO memory
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Crash when USB4 is connected.
[How]
Added an ASIC specific code guard.
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Ahmad Othman <Ahmad.Othman@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
As part of the FPU isolation work documented in
https://patchwork.freedesktop.org/series/93042/, isolate code that uses
FPU in DSC to DML, where all FPU code should locate.
This change does not refactor any functions but move code around.
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Anson Jacob <Anson.Jacob@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Created new fields that matches new B0 structs On DCN31 the mapping of
DIO output to PHY differs from A0 to B0 boards with new PHY C20 & this
new mapping needed to be handled.
[How]
Mapped new structure based on new structs Added logic for mapping over
A0 and B0 boards Hooked all new structs together.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Ahmad Othman <Ahmad.Othman@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To expose new power optimization flags to PSR interface. It allows the
PSR related power features can be enabled separately base on different
use scenarios.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Updating certain variable blanking calculations to use ceiling function.
Reviewed-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Limit when FPU is enabled to only functions that does FPU operations for
dcn20_resource_construct, which gets called during driver
initialization.
Enabling FPU operation disables preemption. Sleeping functions(mutex
(un)lock, memory allocation using GFP_KERNEL, etc.) should not be called
when preemption is disabled.
Fixes the following case caught by enabling
CONFIG_DEBUG_ATOMIC_SLEEP in kernel config
[ 1.338434] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:281
[ 1.347395] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 197, name: systemd-udevd
[ 1.356356] CPU: 7 PID: 197 Comm: systemd-udevd Not tainted 5.13.0+ #3
[ 1.356358] Hardware name: System manufacturer System Product Name/PRIME X570-PRO, BIOS 3405 02/01/2021
[ 1.356360] Call Trace:
[ 1.356361] dump_stack+0x6b/0x86
[ 1.356366] ___might_sleep.cold+0x87/0x98
[ 1.356370] __might_sleep+0x4b/0x80
[ 1.356372] mutex_lock+0x21/0x50
[ 1.356376] smu_get_uclk_dpm_states+0x3f/0x80 [amdgpu]
[ 1.356538] pp_nv_get_uclk_dpm_states+0x35/0x50 [amdgpu]
[ 1.356711] init_soc_bounding_box+0xf9/0x210 [amdgpu]
[ 1.356892] ? create_object+0x20d/0x340
[ 1.356897] ? dcn20_resource_construct+0x46f/0xd30 [amdgpu]
[ 1.357077] dcn20_resource_construct+0x4b1/0xd30 [amdgpu]
...
Tested on: 5700XT (NAVI10 0x1002:0x731F 0x1DA2:0xE410 0xC1)
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Anson Jacob <Anson.Jacob@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the vbios config and driver config are different, if we update
clock to lower before call program_timing and program_pixel_clk, garbage
appear.
[How]
Align bw context with hw config when system resume
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stutter mode is a power saving feature on GPUs, however at
least one early raven system exhibits stability issues with
it. Add a quirk to disable it for that system.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214417
Fixes: 005440066f ("drm/amdgpu: enable gfxoff again on raven series (v2)")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF298ceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGIJYH/1rsEFQQ6caeQdy1
z9eFIe48DNM4l7bFk+qEj2UAbzPdahVJ299Mg5fW0n2CDemOc9/n0b9TxQ37YObi
mOzu0xwJVupIxkyFMPQSSc2q8aLm67NSpJy08DsmaNses5hSvu8x15RPHLQTybjt
SwtKns+jpCq79P1GWbrB5e5UkLb0VNoxNp4L1U4pMrYGcEkJUXbaxNY2V/JcXdM7
Vtn+qN0T/J6V6QVftv0t8Ecj3bjEnmL3kZHaTaNg3dGeKRpCGyHc5lcBQ0cNFG6t
vjZ9VbuhBzGI3TN2tHH5hpA1UXo7HPBBCwQqxF1jeGLGHULikYwZ3TAPWqL3QZqC
9cxr9SY=
=p75d
-----END PGP SIGNATURE-----
BackMerge tag 'v5.15-rc7' into drm-next
The msm next tree is based on rc3, so let's just backmerge rc7 before pulling it in.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Why]
A deadlock in the kernel occurs when we fallback from the V3 to V2
add_topology_to_display or remove_topology_to_display because they
both try to acquire the dtm_mutex but recursive locking isn't
supported on mutex_lock().
[How]
Make the mutex_lock/unlock more fine grained and move them up such that
they're only required for the psp invocation itself.
Fixes: bf62221e9d ("drm/amd/display: Add DCN3.1 HDCP support")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[WHY]
On certain configs, SMU clock table voltages don't match which cause parser
to behave incorrectly by leaving dcfclk and socclk table entries unpopulated.
[HOW]
Currently the function that finds the corresponding clock for a given voltage
only checks for exact voltage level matches. In the case that no match gets
found, parser now falls back to searching for the max clock which meets the
requested voltage (i.e. its corresponding voltage is below requested).
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
CVE-2021-42327 was fixed by:
commit f23750b5b3
Author: Thelford Williams <tdwilliamsiv@gmail.com>
Date: Wed Oct 13 16:04:13 2021 -0400
drm/amdgpu: fix out of bounds write
but amdgpu_dm_debugfs.c contains more of the same issue so fix the
remaining ones.
v2:
* Add missing fix in dp_max_bpc_write (Harry Wentland)
Fixes: 918698d5c2 ("drm/amd/display: Return the number of bytes parsed than allocated")
Signed-off-by: Patrik Jakobsson <pjakobsson@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
UAPI Changes:
Nope!
Cross-subsystem Changes:
drm_dp_update_payload_part1() takes a new argument for specifying what the
VCPI slot start is
Core Changes:
Make the DP MST helpers aware of the current starting VCPI slot/VCPI total
slot count...
Driver Changes:
...and then add support for taking advantage of this for 128b/132b links on DP
2.0 for amdgpu
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bf8e724cc0c8803d58a8d730fd6883c991376a76.camel@redhat.com
Need to guard some things with CONFIG_DRM_AMD_DC_DCN.
Fixes: 41724ea273 ("drm/amd/display: Add DP 2.0 MST DM Support")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211027223914.1776061-1-alexander.deucher@amd.com
[Why]
Add DP2 MST and debugfs support
[How]
Update the slot info based on the link encoding format
Reviewed-by: "Lin, Wayne" <Wayne.Lin@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-5-lyude@redhat.com
[Why]
configure/call DC interface for DP2 mst support. This is needed to make DP2
mst work.
[How]
- add encoding type, logging, mst update/reduce payload functions
Use the link encoding to determine the DP type (1.4 or 2.0) and add a
flag to dc_stream_update to determine whether to increase/reduce
payloads.
v2:
* add DP_UNKNOWN_ENCODING handling
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: "Lin, Wayne" <Wayne.Lin@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-4-lyude@redhat.com
8b/10b encoding format requires to reserve the first slot for
recording metadata. Real data transmission starts from the second slot,
with a total of available 63 slots available.
In 128b/132b encoding format, metadata is transmitted separately
in LLCP packet before MTP. Real data transmission starts from
the first slot, with a total of 64 slots available.
v2:
* Move total/start slots to mst_state, and copy it to mst_mgr in
atomic_check
v3:
* Only keep the slot info on the mst_state
* add a start_slot parameter to the payload function, to facilitate non
atomic drivers (this is a temporary workaround and should be removed when
we are moving out the non atomic driver helpers)
v4:
*fixed typo and formatting
v5: (no functional changes)
* Fixed formatting in drm_dp_mst_update_slots()
* Reference mst_state instead of mst_state->mgr for debugging info
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
[v5 nitpicks]
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025223825.301703-3-lyude@redhat.com
This reverts commits ddab8bd788 ("drm/amd/display: Fix two cursor duplication
when using overlay") and e7d9560aea ("Revert "drm/amd/display: Fix overlay
validation by considering cursors"").
tl;dr ChromeOS uses the atomic interface for everything except the cursor. This
is incorrect and forces amdgpu to disable some hardware features. Let's revert
the ChromeOS-specific workaround in mainline and allow the Chrome team to keep
it internally in their own tree.
See [1] for more details. This patch is an alternative to [2], which added
ChromeOS detection.
[1]: https://lore.kernel.org/amd-gfx/JIQ_93_cHcshiIDsrMU1huBzx9P9LVQxucx8hQArpQu7Wk5DrCl_vTXj_Q20m_L-8C8A5dSpNcSJ8ehfcCrsQpfB5QG_Spn14EYkH9chtg0=@emersion.fr/
[2]: https://lore.kernel.org/amd-gfx/20211011151609.452132-1-contact@emersion.fr/
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: ddab8bd788 ("drm/amd/display: Fix two cursor duplication when using overlay")
Fixes: e7d9560aea ("Revert "drm/amd/display: Fix overlay validation by considering cursors"")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
B0 internal rev_id is 0x01, B1 internal rev_id is 0x02.
The external rev_id for B0 and B1 is 0x20.
The original expression is not suitable for B1.
v2: squash in fix for display code (Alex)
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
bios_golden_init will override dccg_init during init_hw.
[How]
Move dccg_init to after bios_golden_init.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
The original latencies were causing underflow in some modes
[how]
Replace with the up-to-date watermark values based on new measurments
Reviewed-by: Ahmad Othman <ahmad.othman@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Z9 latency is higher than when we originally tuned the watermark
parameters, causing underflow. Increasing the value until the latency
issues is resolved.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Immediate flip can be enabled dynamically and has higher BW requirements
when validating which voltage mode to use.
If we validate when it's not set then potentially DCFCLK will be too low
and we will underflow.
[How]
DM always requires support so always require it as part of DML input
parameters.
This can't be enabled unconditionally on older ASIC because it blocks
some expected modes so only target DCN3.1 for now.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Prefetch BW calculated is lower than the DML reference because of a
porting error that's excluding cursor and row bandwidth from the
pixel data bandwidth.
[How]
Change the dml_max4 to dml_max3 and include cursor and row bandwidth
in the same calculation as the rest of the pixel data during vactive.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
The requirement is that image width up to 4096 shall be supported
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Size can be any value and is user controlled resulting in overwriting the
40 byte array wr_buf with an arbitrary length of data from buf.
Signed-off-by: Thelford Williams <tdwilliamsiv@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
B0 internal rev_id is 0x01, B1 internal rev_id is 0x02.
The external rev_id for B0 and B1 is 0x20.
The original expression is not suitable for B1.
v2: squash in fix for display code (Alex)
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1445d967fb.
This patch introduced a couple of dmesg warnings, this is not a valid
approach anymore. For this reason, we are reverting this patch, and we
need to revert the workaround patch.
v2: squash in unused variable removal (Alex)
Cc: Hanghong Ma <hanghong.ma@amd.com>
Cc: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
V3_4 is latest in use.
[How]
Add bios parser support for firmware_info_v3_4 along
with some relevant fields it is also retrieving from dce_info
and smu_info.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This DC patchset brings improvements in multiple areas. In summary, we
highlight:
* Fix some issues such as DP2 problem, prefetch bandwidth calculation
for DCN3.1 and others.
* Increased Z9 latency and removed z10 save after dsc disable.
* Revert a couple of bad changes.
* Added missing PSR state patch.
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Disable hdmistream and hdmichar root clocks when not being used.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
bios_golden_init will override dccg_init during init_hw.
[How]
Move dccg_init to after bios_golden_init.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
