The IRQC module clock is managed through Runtime PM and PM Domains.
If wake-up is enabled, this clock must not be disabled during system
suspend.
Hence implement irq_chip.irq_set_wake(), which increments/decrements the
clock's enable_count when needed.
This fixes wake-up by gpio-keys on r8a73a4/ape6evm.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lkml.kernel.org/r/1427889606-18671-1-git-send-email-geert+renesas@glider.be
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On the Armada 370/XP SoCs, in standby mode the SoC stay powered and it
is possible to wake-up from any interrupt sources. This patch adds
flag to the MPIC irqchip driver to let linux know this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1427724278-12379-5-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We add new functions to start and stop the GIC counter since there are no
guarantees the counter will be running after a CPU reset. The GIC counter
is stopped by setting the 29th bit on the GIC Config register and it is
started by clearing that bit.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Link: https://lkml.kernel.org/r/1427113923-9840-2-git-send-email-markos.chandras@imgtec.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is just enough to let pm_clk_*() enable the functional clock, and
manage it for suspend/resume, if present.
Before, it was assumed enabled by the bootloader or reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lkml.kernel.org/r/1426704961-27322-3-git-send-email-geert+renesas@glider.be
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In a uniprocessor implementation the interrupt processor targets
registers are read-as-zero/write-ignored (RAZ/WI). Unfortunately
gic_get_cpumask() will print a critical message saying
GIC CPU mask not found - kernel will fail to boot.
if these registers all read as zero, but there won't actually be
a problem on uniprocessor systems and the kernel will boot just
fine. Skip this check if we're running a UP kernel or if we
detect that the hardware only supports a single processor.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Link: https://lkml.kernel.org/r/1426141291-21641-1-git-send-email-sboyd@codeaurora.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A common use of gic_arch_extn is to set up additional flags
to the GIC irqchip. It looks like a benign enough hack that
doesn't really require the users of that feature to be converted
to stacked domains.
Add a gic_set_irqchip_flags() function that platform code can
call instead of using the dreaded gic_arch_extn.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088737-15817-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The only user of the so called "routable domain" functionality
now being fixed, let's clean up the GIC.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Tegra's LIC (Legacy Interrupt Controller) has been so far only
supported as a weird extension of the GIC, which is not exactly
pretty.
The stacked IRQ domain framework fits this pretty well, and allows
the LIC code to be turned into a standalone irqchip. In the process,
make the driver DT aware, something that was sorely missing from
the mach-tegra implementation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088583-15097-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to let the Performance Monitoring Unit interrupts flowing in the MPIC,
we need to unmask these interrupts in the Coherency Fabric Local Interrupt Mask
Register.
Since this register is a CPU-local register, unmasking this interrupt needs to
be done on the boot CPU when the driver initializes, but also on the secondary
CPU when they are brought up.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425379400-4346-4-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit introduces a helper function is_percpu_irq(), to be used
when interrupts are mapped to decide which ones are set as per CPU.
This change will allow to extend the list of per cpu interrupts in a less
intrusive fashion; also, it makes the code slightly more readable by keeping
a list of the per CPU interrupts.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425379400-4346-3-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The irqchip driver called armada_xp_mpic_smp_cpu_init() when CONFIG_SMP=Y
to initialize some per cpu registers. The function is called on each
CPU by calling it explicitly on the boot CPU and then using a CPU notifier
for the non boot CPUs.
This commit removes the CONFIG_SMP constrain, so the per cpu registers are
also initialized when CONFIG_SMP=N, which is the right thing to do.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425379400-4346-2-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds support for Vybrid's interrupt router. On VF6xx models,
almost all peripherals can be used by either of the two CPU's,
the Cortex-A5 or the Cortex-M4. The interrupt router routes the
peripheral interrupts to the configured CPU.
This IRQ chip driver configures the interrupt router to route
the requested interrupt to the CPU the kernel is running on.
The driver makes use of the irqdomain hierarchy support. The
parent is given by the device tree. This should be one of the
two possible parents either ARM GIC or the ARM NVIC interrupt
controller. The latter is currently not yet supported.
Note that there is no resource control mechnism implemented to
avoid concurrent access of the same peripheral. The user needs
to make sure to use device trees which assign the peripherals
orthogonally. However, this driver warns the user in case the
interrupt is already configured for the other CPU. This provides
a poor man's resource controller.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Link: https://lkml.kernel.org/r/1425249689-32354-2-git-send-email-stefan@agner.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On the Cortex-A9-based Armada SoCs, the MPIC is not the primary interrupt
controller. Yet, it still has to handle some per-cpu interrupt.
To do so, it is chained with the GIC using a per-cpu interrupt. However, the
current code only call irq_set_chained_handler, which is called and enable that
interrupt only on the boot CPU, which means that the parent per-CPU interrupt
is never unmasked on the secondary CPUs, preventing the per-CPU interrupt to
actually work as expected.
This was not seen until now since the only MPIC PPI users were the Marvell
timers that were not working, but not used either since the system use the ARM
TWD by default, and the ethernet controllers, that are faking there interrupts
as SPI, and don't really expect to have interrupts on the secondary cores
anyway.
Add a CPU notifier that will enable the PPI on the secondary cores when they
are brought up.
Cc: <stable@vger.kernel.org> # 3.15+
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425378443-28822-1-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This driver is used to enable System Configuration Register controlled
External, CTI (Core Sight), PMU (Performance Management), and PL310 L2
Cache IRQs prior to use.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lkml.kernel.org/r/1424272444-16230-3-git-send-email-lee.jones@linaro.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
Pull irqchip updates from Ingo Molnar:
"Various irqchip driver updates, plus a genirq core update that allows
the initial spreading of irqs amonst CPUs without having to do it from
user-space"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix null pointer reference in irq_set_affinity_hint()
irqchip: gic: Allow interrupt level to be set for PPIs
irqchip: mips-gic: Handle pending interrupts once in __gic_irq_dispatch()
irqchip: Conexant CX92755 interrupts controller driver
irqchip: Devicetree: document Conexant Digicolor irq binding
irqchip: omap-intc: Remove unused legacy interface for omap2
irqchip: omap-intc: Fix support for dm814 and dm816
irqchip: mtk-sysirq: Get irq number from register resource size
irqchip: renesas-intc-irqpin: r8a7779 IRLM setup support
genirq: Set initial affinity in irq_set_affinity_hint()
Common: Optional support for adding a small amount of polling on each HLT
instruction executed in the guest (or equivalent for other architectures).
This can improve latency up to 50% on some scenarios (e.g. O_DSYNC writes
or TCP_RR netperf tests). This also has to be enabled manually for now,
but the plan is to auto-tune this in the future.
ARM/ARM64: the highlights are support for GICv3 emulation and dirty page
tracking
s390: several optimizations and bugfixes. Also a first: a feature
exposed by KVM (UUID and long guest name in /proc/sysinfo) before
it is available in IBM's hypervisor! :)
MIPS: Bugfixes.
x86: Support for PML (page modification logging, a new feature in
Broadwell Xeons that speeds up dirty page tracking), nested virtualization
improvements (nested APICv---a nice optimization), usual round of emulation
fixes. There is also a new option to reduce latency of the TSC deadline
timer in the guest; this needs to be tuned manually.
Some commits are common between this pull and Catalin's; I see you
have already included his tree.
ARM has other conflicts where functions are added in the same place
by 3.19-rc and 3.20 patches. These are not large though, and entirely
within KVM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJU28rkAAoJEL/70l94x66DXqQH/1TDOfJIjW7P2kb0Sw7Fy1wi
cEX1KO/VFxAqc8R0E/0Wb55CXyPjQJM6xBXuFr5cUDaIjQ8ULSktL4pEwXyyv/s5
DBDkN65mriry2w5VuEaRLVcuX9Wy+tqLQXWNkEySfyb4uhZChWWHvKEcgw5SqCyg
NlpeHurYESIoNyov3jWqvBjr4OmaQENyv7t2c6q5ErIgG02V+iCux5QGbphM2IC9
LFtPKxoqhfeB2xFxTOIt8HJiXrZNwflsTejIlCl/NSEiDVLLxxHCxK2tWK/tUXMn
JfLD9ytXBWtNMwInvtFm4fPmDouv2VDyR0xnK2db+/axsJZnbxqjGu1um4Dqbak=
=7gdx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM update from Paolo Bonzini:
"Fairly small update, but there are some interesting new features.
Common:
Optional support for adding a small amount of polling on each HLT
instruction executed in the guest (or equivalent for other
architectures). This can improve latency up to 50% on some
scenarios (e.g. O_DSYNC writes or TCP_RR netperf tests). This
also has to be enabled manually for now, but the plan is to
auto-tune this in the future.
ARM/ARM64:
The highlights are support for GICv3 emulation and dirty page
tracking
s390:
Several optimizations and bugfixes. Also a first: a feature
exposed by KVM (UUID and long guest name in /proc/sysinfo) before
it is available in IBM's hypervisor! :)
MIPS:
Bugfixes.
x86:
Support for PML (page modification logging, a new feature in
Broadwell Xeons that speeds up dirty page tracking), nested
virtualization improvements (nested APICv---a nice optimization),
usual round of emulation fixes.
There is also a new option to reduce latency of the TSC deadline
timer in the guest; this needs to be tuned manually.
Some commits are common between this pull and Catalin's; I see you
have already included his tree.
Powerpc:
Nothing yet.
The KVM/PPC changes will come in through the PPC maintainers,
because I haven't received them yet and I might end up being
offline for some part of next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (130 commits)
KVM: ia64: drop kvm.h from installed user headers
KVM: x86: fix build with !CONFIG_SMP
KVM: x86: emulate: correct page fault error code for NoWrite instructions
KVM: Disable compat ioctl for s390
KVM: s390: add cpu model support
KVM: s390: use facilities and cpu_id per KVM
KVM: s390/CPACF: Choose crypto control block format
s390/kernel: Update /proc/sysinfo file with Extended Name and UUID
KVM: s390: reenable LPP facility
KVM: s390: floating irqs: fix user triggerable endless loop
kvm: add halt_poll_ns module parameter
kvm: remove KVM_MMIO_SIZE
KVM: MIPS: Don't leak FPU/DSP to guest
KVM: MIPS: Disable HTW while in guest
KVM: nVMX: Enable nested posted interrupt processing
KVM: nVMX: Enable nested virtual interrupt delivery
KVM: nVMX: Enable nested apic register virtualization
KVM: nVMX: Make nested control MSRs per-cpu
KVM: nVMX: Enable nested virtualize x2apic mode
KVM: nVMX: Prepare for using hardware MSR bitmap
...
Pull MIPS fixes from Ralf Baechle:
"The pending MIPS fixes for 3.19. All across the field and nothing
particularly severe or dramatic"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (23 commits)
IRQCHIP: mips-gic: Avoid rerouting timer IRQs for smp-cmp
MIPS: Fix syscall_get_nr for the syscall exit tracing.
MIPS: elf2ecoff: Ignore PT_MIPS_ABIFLAGS program headers.
MIPS: elf2ecoff: Rewrite main processing loop to switch.
MIPS: fork: Fix MSA/FPU/DSP context duplication race
MIPS: Fix C0_Pagegrain[IEC] support.
MIPS: traps: Fix inline asm ctc1 missing .set hardfloat
MIPS: mipsregs.h: Add write_32bit_cp1_register()
MIPS: Fix kernel lockup or crash after CPU offline/online
MIPS: OCTEON: fix kernel crash when offlining a CPU
MIPS: ARC: Fix build error.
MIPS: IRQ: Fix disable_irq on CPU IRQs
MIPS: smp-mt,smp-cmp: Enable all HW IRQs on secondary CPUs
MIPS: Fix restart of indirect syscalls
MIPS: ELF: fix loading o32 binaries on 64-bit kernels
MIPS: mips-cm: Fix sparse warnings
MIPS: Kconfig: Fix recursive dependency.
MIPS: Compat: Fix build error if CONFIG_MIPS32_COMPAT but no compat ABI.
MIPS: JZ4740: Fixup #include's (sparse)
MIPS: Wire up execveat(2).
...
The cevt-r4k driver used to call into the GIC driver to find whether the
timer was pending, but only with External Interrupt Controller (EIC)
mode, where the Cause.IP bits can't be used as they encode the interrupt
priority level (Cause.RIPL) instead.
However commit e9de688dac ("irqchip: mips-gic: Support local
interrupts") changed the condition from cpu_has_veic to gic_present.
This fails on cores such as P5600 which have a GIC but the local
interrupts aren't routable by the GIC, causing c0_compare_int_usable()
to consider the interrupt unusable so r4k_clockevent_init() fails.
The previous behaviour, added in commit 98b67c37db ("MIPS: Add EIC
support for GIC."), wasn't really correct either as far as I can tell,
since P5600 apparently supports EIC mode too, and in any case the use of
Cause.TI with r2 should have been sufficient anyway since commit
010c108d7a ("MIPS: PowerTV: Fix support for timer interrupts with > 64
external IRQs").
Therefore drop the call into the gic driver altogether, and add a
comment in c0_compare_int_pending() to clarify that Cause.TI does get
checked since MIPS r2.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: e9de688dac ("irqchip: mips-gic: Support local interrupts")
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J. Hill <steven.hill@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9077/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit e9de688dac ("irqchip: mips-gic: Support local interrupts")
changed the GIC irqchip driver so that all local interrupts were routed
to the same CPU pin used for external interrupts. Unfortunately this
causes a regression when smp-cmp is used. The CPUs are started by the
bootloader and put in a timer based waiting poll loop, but when their
timer interrupts are rerouted to a different IRQ pin which is not
unmasked they never wake up.
Since smp-cmp support is deprecated and everybody who was using it
should be switching to smp-cps which brings up the secondary CPUs
without bootloader assistance, I've gone for the simple fix which can be
easily removed once smp-cmp is removed, rather than a fully generic fix.
In __gic_init() the local GIC_VPE_TIMER_MAP register is read to find the
boot-time routing of the local timer interrupt, and a chained handler is
added to that CPU pin as well as the normal one.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: e9de688dac ("irqchip: mips-gic: Support local interrupts")
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Patchwork: https://patchwork.linux-mips.org/patch/9081/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
During a recent cleanup of the arm64 DTs it has become clear that
the handling of PPIs in xxxx_set_type() is incorrect. The ARM TRMs
for GICv2 and later allow for "implementation defined" support for
setting the edge or level type of the PPI interrupts and don't restrict
the activation level of the signal. Current ARM implementations
do restrict the PPI level type to IRQ_TYPE_LEVEL_LOW, but licensees
of the IP can decide to shoot themselves in the foot at any time.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Marc Zyngier <Marc.Zyngier@arm.com>
Cc: LAKML <linux-arm-kernel@lists.infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Link: http://lkml.kernel.org/r/1421772779-25764-1-git-send-email-Liviu.Dudau@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When an interrupt occurs __gic_irq_dispatch() continuously reads local
and shared pending registers until all is serviced before
returning. The problem with that is that it could introduce a long
delay before returning if a piece of hardware keeps triggering while
in one of these loops.
To ensure fairness and priority doesn't get skewed a lot, read local
and shared pending registers once to service each pending IRQ once.
If another interupt triggers while servicing the current ones, then we
shall re-enter the handler after we return.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: <linux-mips@linux-mips.org>
Link: http://lkml.kernel.org/r/1421668289-828-1-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add interrupt controller driver to the Conexant CX92755 SoC, part of the
Digicolor SoCs series. Use the generic irq framework support. Use syscon to
access the system global UC_IRQ_CONTROL register.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/5b769e3c23dfa5fde08c4f3bc966c2c2b3921d8a.1421317616.git.baruch@tkos.co.il
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Nowadays omap2 is booting in device tree only mode so there is no
need to keep the legacy interface around for omap2_init_irq().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1421187806-6804-3-git-send-email-tony@atomide.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On dm81xx we have 128 interrupts like am33xx has. Let's add
compatible flags for dm814x and dm816x, and document the
existing binding.
As the dm81xx are booting in device tree only mode, we can now
also remove ti81xx_init_irq() legacy function.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1421187806-6804-2-git-send-email-tony@atomide.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Originally mtk-sysirq hardcoded supported irq number to 224. This
was fine since all SoCs before support the same number of irqs for
intpol.
However MT8173 intpol support 32 more irq pins, changes to get
irq number from register resource size to suppor MT8173 properly.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Cc: <srv_heupstream@mediatek.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Robert Richter <rrichter@cavium.com>
Cc: Mark Brown <broonie@linaro.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: <marc.zyngier@arm.com>
Cc: <peter.maydell@linaro.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1421054073-43468-3-git-send-email-eddie.huang@mediatek.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add r8a7779 specific support for IRLM bit configuration
in the INTC-IRQPIN driver. Without this code we need
special workaround code in arch/arm/mach-shmobile.
The IRLM bit for the INTC hardware exists on various
older SH-based SoCs and is used to select between two
modes for the external interrupt pins IRQ0 to IRQ3:
IRLM = 0: (default from reset on r8a7779)
In this mode the pins IRQ0 to IRQ3 are used together
to give a value between 0 and 15 to the SoC. External
logic is required for masking. This mode is not
supported by the INTC-IRQPIN driver.
IRLM = 1: (needs this patch or configuration elsewhere)
In this mode IRQ0 to IRQ3 operate as 4 individual
external interrupt pins. In this mode the SMSC ethernet
chip can be used via IRQ1 on r8a7779 Marzen. This mode
is the only supported mode by the INTC-IRQPIN driver.
For this patch to work the r8a7779 DTS needs to pass
the ICR0 register as the last register bank.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: horms@verge.net.au
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/20141203121803.5936.35881.sendpatchset@w520
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The gic_send_sgi() function used hardcoded bit shift values to
generate the ICC_SGI1R_EL1 register value.
Replace this with symbolic names to allow reusing them later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This patch makes the bitmask for AIC_SRCTYPE consistent
with that of its valid values, and prevents the priority
field at bits 2:0 from being clobbered by an incorrect
AND with the AIC_SRCTYPE mask.
Signed-off-by: Gavin Li <gavinli@thegavinli.com>
Cc: <stable@vger.kernel.org> # v3.17+
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Link: https://lkml.kernel.org/r/1420598843-8409-1-git-send-email-gavinli@thegavinli.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
commit 55601c9f24 (arm: omap: intc: switch over
to linear irq domain) introduced a regression with
SDMA legacy driver because that driver strictly depends
on INTC's IRQs starting at NR_IRQs. Aparently
irq_domain_add_linear() won't guarantee that, since we see
a 7 IRQs difference when booting with and without the
commit cited above.
Until arch/arm/plat-omap/dma.c is properly fixed, we
must maintain OMAP2/3 using irq_domain_add_legacy().
A FIXME note was added so people know to delete that
code once that legacy DMA driver is fixed up.
Fixes: 55601c9f24 (arm: omap: intc: switch over to linear irq domain)
Cc: <stable@vger.kernel.org> # v3.18
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Link: https://lkml.kernel.org/r/1420576688-10604-1-git-send-email-balbi@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
arm64 defconfig spits out the following compiler warning from the ITS
driver:
In file included from include/linux/bitmap.h:9:0,
from drivers/irqchip/irq-gic-v3-its.c:18:
drivers/irqchip/irq-gic-v3-its.c: In function ‘its_create_device’:
include/linux/kernel.h:716:17: warning: comparison of distinct pointer types lacks a cast
(void) (&_max1 == &_max2); \
^
drivers/irqchip/irq-gic-v3-its.c:1056:12: note: in expansion of macro ‘max’
nr_ites = max(2, roundup_pow_of_two(nvecs));
Fix the warning by specifying the decimal constant `2' explicitly as an
unsigned long type.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1418825469-30529-1-git-send-email-will.deacon@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Beniamino noticed a bug that an invalid DT file for the mediatek interrupt
polarity extension will cause kernel oops.
The reason is that the interrupt polarity support for mediatek chips
merely checks for NULL pointer instead of a casted error return
value in mtk_sysirq_of_init() so any other casted error value passes
the NULL pointer check and causes a kernel panic when dereferenced.
Use IS_ERR() and return the error value via PTR_ERR().
[ jac: took V2 over V3 for diff formatting, hand-added V3 changes,
tweaked subject line. ]
Reported-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Link: https://lkml.kernel.org/r/1418205302-22531-1-git-send-email-yingjoe.chen@mediatek.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull irq domain ARM updates from Thomas Gleixner:
"This set of changes make use of hierarchical irqdomains to provide:
- MSI/ITS support for GICv3
- MSI support for GICv2m
- Interrupt polarity extender for GICv1
Marc has come more cleanups for the existing extension hooks of GIC in
the pipeline, but they are going to be 3.20 material"
* 'irq-irqdomain-arm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
irqchip: gicv3-its: Fix ITT allocation
irqchip: gicv3-its: Move some alloc/free code to activate/deactivate
irqchip: gicv3-its: Fix domain free in multi-MSI case
irqchip: gic: Remove warning by including linux/irqdomain.h
irqchip: gic-v2m: Add DT bindings for GICv2m
irqchip: gic-v2m: Add support for ARM GICv2m MSI(-X) doorbell
irqchip: mtk-sysirq: dt-bindings: Add bindings for mediatek sysirq
irqchip: mtk-sysirq: Add sysirq interrupt polarity support
irqchip: gic: Support hierarchy irq domain.
irqchip: GICv3: Binding updates for ITS
irqchip: GICv3: ITS: enable compilation of the ITS driver
irqchip: GICv3: ITS: plug ITS init into main GICv3 code
irqchip: GICv3: ITS: DT probing and initialization
irqchip: GICv3: ITS: MSI support
irqchip: GICv3: ITS: device allocation and configuration
irqchip: GICv3: ITS: tables allocators
irqchip: GICv3: ITS: LPI allocator
irqchip: GICv3: ITS: irqchip implementation
irqchip: GICv3: ITS command queue
irqchip: GICv3: rework redistributor structure
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
When issuing a MAPD command, one of the parameters passed to the ITS
is the number of EventID bits used to index the per-device Interrupt
Translation Table (ITT). Crucially, this is the number of bits
*minus one*.
This has two consequences:
- The size of the ITT has to be a strict power of two, no matter
how many different events the device is actually going to generate.
- It is impossible to express an ITT with a single entry, as you
would have to tell the ITS to "use zero bit from the EventID",
and that clashes with "minus one" above.
Fix this by allocating the ITT with the number of vectors rounded up
to the next power of two, with a minimum of two entries.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Yun Wu (Abel) <wuyun.wu@huawei.com>
Cc: Robert Richter <robert.richter@caviumnetworks.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ITS code could do a bit less in the alloc/free paths, and a bit
more in the activate/deactivate methods, giving a better separation
between software allocation and HW programing.
Suggested-by: Wuyun Wu (Abel) <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Yun Wu (Abel) <wuyun.wu@huawei.com>
Cc: Robert Richter <robert.richter@caviumnetworks.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
