Make sock_filter_is_valid_access consistent with other is_valid_access
helpers.
Requested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver and hardware supports IPv6 offload, however it
isn't enabled. Set the NETIF_F_IPV6_CSUM feature to inform the
network layer that this driver can offload IPV6 TCP and UDP
checksums. This change has been tested on an Armada 370 and the
feature support confirmed with several device datasheets
including the Armada XP and Armada 3700.
Signed-off-by: Andrew Pilloud <andrewpilloud@igneoussystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few last patches for 4.14, nothing really major here.
Major changes:
wil6210
* support FW RSSI reporting (by mistake this was accidentally
mentioned already in the previous pull request, but now it's really
included)
* make debugfs optional, adds new Kconfig option CONFIG_WIL6210_DEBUGFS
qtnfmac
* implement 64-bit DMA support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZqWycAAoJEG4XJFUm622bLCEH/RbIdVLXvC7AM/5RGE4p8fEL
WjtMaGK5T14+OwbWSrYbtLPszJKfAt5MoG0Xl+c0xt+n7a6J+8GlyfXdxkYexkUN
8gt0LlSU0ExDx+VOiRWM9XFKjKy0WPx6xPI86DLGcGB/ygiCMI3ueot/tilNBK7V
lu4a0lqFifoIOOHynBhwvrhgrnyk5B5EJCSalwCN4NmaFveWjTzrBRNyi6BPJRgv
3iR1URNfzUYDmYDYS1EXB6+01PBpznrMSSFB/mxNSv5iiC988pc0ebj+UDi5Ms8Y
91gxlgKCbPbVj+D4M/Rwg2sAnAVCCLcEeheF2TmL1KoVUFyMBGYtyRS0qIUeQRM=
=p+hy
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-09-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
Few last patches for 4.14, nothing really major here.
Major changes:
wil6210
* support FW RSSI reporting (by mistake this was accidentally
mentioned already in the previous pull request, but now it's really
included)
* make debugfs optional, adds new Kconfig option CONFIG_WIL6210_DEBUGFS
qtnfmac
* implement 64-bit DMA support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the do while loop the integer counter retries will
always be zero and so the subsequent check to see if it is zero
is always true and therefore redundant. Remove the redundant check
and always return -EIO on this return path. Also unbreak the literal
string in dev_err message to clean up a checkpatch warning.
Detected by CoverityScan, CID#744279 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corentin Labbe says:
====================
net: mdio-mux: Misc fix
This patch series fix minor problems found when working on the
dwmac-sun8i syscon mdio-mux.
Changes since v1:
- Removed obsolete comment about of_mdio_find_bus/put_device
- removed more DRV_VERSION
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_uninit() call put_device (unconditionally) because of
of_mdio_find_bus() in mdio_mux_init.
But of_mdio_find_bus is only called if mux_bus is empty.
If mux_bus is set, mdio_mux_uninit will print a "refcount_t: underflow"
trace.
This patch add a get_device in the other branch of "if (mux_bus)".
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix an old information that mdio-mux-mmioreg can only handle
8bit registers.
This is not true anymore.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the driver version information because this information
is not useful in an upstream kernel driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix checkpatch warning about unnecessary 'out of memory'
message.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix checkpatch warning about NULL Comparison style.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: mvpp2: optional PHYs and GoP link irq
This series aims at making the driver work when no PHY is connected
between a port and the physical layer and not described as a fixed-phy.
This is useful for some usecases such as when a switch is connected
directly to the serdes lanes. It can also be used for SFP ports on the
7k-db and 8k-db while waiting for the phylink support to land in (which
should be part of another series).
This series makes the phy optional in the PPv2 driver, and then adds
the support for the GoP port link interrupt to handle link status
changes on such ports.
This was tested using the SFP ports on the 7k-db and 8k-db boards.
Since v1:
- Now use phy_interface_mode_is_rgmii() in the GoP link patch.
- Added one cosmetic patch to take advantage of phy_interface_mode_is_rgmii()
in the whole PPv2 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A link interrupt can be described. Document this valid interrupt name.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the GoP link interrupt support for when a port isn't
connected to a PHY. Because of this the phylib callback is never called
and the link status management isn't done. This patch use the GoP link
interrupt in such cases to still have a minimal link management. Without
this patch ports not connected to a PHY cannot work.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not necessarily a PHY between the GoP and the physical port.
However, the driver currently makes the "phy" property mandatory,
contrary to what is stated in the device tree bindings. This patch makes
the PHY optional, and aligns the PPv2 driver on its device tree
documentation. However if a PHY is provided, the GoP link interrupt
won't be used.
With this patch switches directly connected to the serdes lanes and SFP
ports on the Armada 8040-db and Armada 7040-db can be used if the link
interrupt is described in the device tree.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all RGMII checks to use the phy_interface_mode_is_rgmii()
helper. This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: spectrum_router: Couple of fixes
Ido Schimmel (2):
mlxsw: spectrum_router: Trap packets hitting anycast routes
mlxsw: spectrum_router: Set abort trap in all virtual routers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the abort mechanism is invoked a default route directing packets to
the CPU is programmed in all the virtual routers currently in use. This
can result in packet loss in case a new VRF is configured.
Upon abort, program the default route in all virtual routers, whether
they are in use or not.
The patch is directed at net-next since post-abort fixes aren't critical
and packet loss due to a missing default route will be insignificant
compared to packet loss caused by the CPU port policer.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I relied on the fact that anycast routes use the loopback device as
their nexthop device to trap packets hitting them to the CPU.
After commit 4832c30d54 ("net: ipv6: put host and anycast routes on
device with address") this is no longer the case and such routes are
programmed with a forward action (note the 'offload' flag):
anycast cafe:: dev enp3s0np7 proto kernel metric 0 offload pref medium
This will prevent the router from locally receiving packets destined to
the Subnet-Router anycast address.
Fix this by specifically programming anycast routes with action trap,
which results in the following output:
anycast cafe:: dev enp3s0np7 proto kernel metric 0 pref medium
Fixes: 4832c30d54 ("net: ipv6: put host and anycast routes on device with address")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau says:
====================
bpf: Improve LRU map lookup performance
This patchset improves the lookup performance of the LRU map.
Please see individual patch for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch writes 'node->ref = 1' only if node->ref is 0.
The number of lookups/s for a ~1M entries LRU map increased by
~30% (260097 to 343313).
Other writes on 'node->ref = 0' is not changed. In those cases, the
same cache line has to be changed anyway.
First column: Size of the LRU hash
Second column: Number of lookups/s
Before:
> echo "$((2**20+1)): $(./map_perf_test 1024 1 $((2**20+1)) 10000000 | awk '{print $3}')"
1048577: 260097
After:
> echo "$((2**20+1)): $(./map_perf_test 1024 1 $((2**20+1)) 10000000 | awk '{print $3}')"
1048577: 343313
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inline the lru map lookup to save the cost in making calls to
bpf_map_lookup_elem() and htab_lru_map_lookup_elem().
Different LRU hash size is tested. The benefit diminishes when
the cache miss starts to dominate in the bigger LRU hash.
Considering the change is simple, it is still worth to optimize.
First column: Size of the LRU hash
Second column: Number of lookups/s
Before:
> for i in $(seq 9 20); do echo "$((2**i+1)): $(./map_perf_test 1024 1 $((2**i+1)) 10000000 | awk '{print $3}')"; done
513: 1132020
1025: 1056826
2049: 1007024
4097: 853298
8193: 742723
16385: 712600
32769: 688142
65537: 677028
131073: 619437
262145: 498770
524289: 316695
1048577: 260038
After:
> for i in $(seq 9 20); do echo "$((2**i+1)): $(./map_perf_test 1024 1 $((2**i+1)) 10000000 | awk '{print $3}')"; done
513: 1221851
1025: 1144695
2049: 1049902
4097: 884460
8193: 773731
16385: 729673
32769: 721989
65537: 715530
131073: 671665
262145: 516987
524289: 321125
1048577: 260048
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new case to test the LRU lookup performance.
At the beginning, the LRU map is fully loaded (i.e. the number of keys
is equal to map->max_entries). The lookup is done through key 0
to num_map_entries and then repeats from 0 again.
This patch also creates an anonymous struct to properly
name the test params in stress_lru_hmap_alloc() in map_perf_test_kern.c.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-09-01
This should be the last ipsec-next pull request for this
release cycle:
1) Support netdevice ESP trailer removal when decryption
is offloaded. From Yossi Kuperman.
2) Fix overwritten return value of copy_sec_ctx().
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
bpf: Add option to set mark and priority in cgroup sock programs
Add option to set mark and priority in addition to bound device for newly
created sockets. Also, allow the bpf programs to use the get_current_uid_gid
helper meaning socket marks, priority and device can be set based on the
uid/gid of the running process.
Sample programs are updated to demonstrate the new options.
v3
- no changes to Patches 1 and 2 which Alexei acked in previous versions
- dropped change related to recursive programs in a cgroup
- updated tests per dropped patch
v2
- added flag to control recursive behavior as requested by Alexei
- added comment to sock_filter_func_proto regarding use of
get_current_uid_gid helper
- updated test programs for recursive option
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update cgrp2 bpf sock tests to check that device, mark and priority
can all be set on a socket via bpf programs attached to a cgroup.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to dump socket settings. Will be used in the next patch
to verify bpf programs are correctly setting mark, priority and
device based on the cgroup attachment for the program run.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add option to detach programs from a cgroup.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update sock test to set mark and priority on socket create.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow BPF programs run on sock create to use the get_current_uid_gid
helper. IPv4 and IPv6 sockets are created in a process context so
there is always a valid uid/gid
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add socket mark and priority to fields that can be set by
ebpf program when a socket is created.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Add IPv6 host dpipe table
This patchset adds IPv6 host dpipe table support. This will provide the
ability to observe the hardware offloaded IPv6 neighbors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for controlling IPv6 neighbor counters via dpipe.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on IPv6 neighbors based on dpipe's host6
table counter status.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 host table dump.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the host entry filler helper to be applicable for both IPv4/6
addresses.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper for accessing destination IP in case of IPv6 neighbor.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IPv6 host table initial support. The action behavior for both IPv4/6
tables is the same, thus the same action dump op is used. Neighbors with
link local address are ignored.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neighbors with link local addresses are not offloaded to the host table,
yet, the are maintained in the driver for adjacency table usage. When
dumping the IPv6 host neighbors this link local neighbors should be
ignored. This patch exports this helper for dpipe usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv6 host table which will be introduced in the
following patches. The fields in the header are added per-use. This header
is global and can be reused by many drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes two trivial typos in net_device_ops documentation,
related to ndo_xdp_flush callback.
Signed-off-by: Rami Rosen <rami.rosen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handling of IPV6_PKTOPTIONS to dccp_v6_do_rcv() in net/dccp/ipv6.c,
similar
to the handling in net/ipv6/tcp_ipv6.c
Signed-off-by: Andrii Vladyka <tulup@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends bridge fdb table tracepoints to also cover
learned fdb entries in the br_fdb_update path. Note that
unlike other tracepoints I have moved this to when the fdb
is modified because this is in the datapath and can generate
a lot of noise in the trace output. br_fdb_update is also called
from added_by_user context in the NTF_USE case which is already
traced ..hence the !added_by_user check.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TC filters when used as classifiers are bound to TC classes.
However, there is a hidden difference when adding them in different
orders:
1. If we add tc classes before its filters, everything is fine.
Logically, the classes exist before we specify their ID's in
filters, it is easy to bind them together, just as in the current
code base.
2. If we add tc filters before the tc classes they bind, we have to
do dynamic lookup in fast path. What's worse, this happens all
the time not just once, because on fast path tcf_result is passed
on stack, there is no way to propagate back to the one in tc filters.
This hidden difference hurts performance silently if we have many tc
classes in hierarchy.
This patch intends to close this gap by doing the reverse binding when
we create a new class, in this case we can actually search all the
filters in its parent, match and fixup by classid. And because
tcf_result is specific to each type of tc filter, we have to introduce
a new ops for each filter to tell how to bind the class.
Note, we still can NOT totally get rid of those class lookup in
->enqueue() because cgroup and flow filters have no way to determine
the classid at setup time, they still have to go through dynamic lookup.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.14. Major changes:
wil6210
* support FW RSSI reporting (by mistake this was accidentally
mentioned already in the previous pull request, but now it's really
included)
* make debugfs optional, adds new Kconfig option CONFIG_WIL6210_DEBUGFS
ACPI will rely on device driver to tell it if the device could support
wakeup function when system in D3 state.
This has caused some platform can't support remote wakeup correctly,
because the ACPI wakeup GPE is not enabled, hence registers the .set_wakeup
callback to handle it if device supports wakeup.
Tested with QCA6174 hw3.0, firmware ('WLAN.RM.4.4.1-00008-QCARMSWP-1')
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The actual PCI suspend/resume in ath10k has been handled in wow.c,
but in the case of the device doesn't support remote wakeup,
the .hif_suspend() and .hif_resume() will never be handled.
ath10k_wow_op_suspend()
{
if (WARN_ON(!test_bit(ATH10K_FW_FEATURE_WOWLAN_SUPPORT,
ar->running_fw->fw_file.fw_features))) {
ret = 1;
goto exit;
}
....
ret = ath10k_hif_suspend(ar);
}
So register the PCI PM core to support the suspend/resume if the device
doesn't support remote wakeup.
Signed-off-by: Ryan Hsu <ryanhsu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Refactor code in order to avoid identical code for different branches.
Addresses-Coverity-ID: 1248728
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
