Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After fixing the obvious errors, the driver will now compile
again on v2.6.34-rc3. First tests with two 4MB flash cards including
erase- and write test with one of the cards where successful.
Also, add two new PCMCIA_DEVICE_PROD_IDs.
[linux@dominikbrodowski.net: clean up commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Due to a broken CFI, they have to be added to jedec_probe.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a slightly modified version of a patch submitted last year by
Reuben Dowle <reuben.dowle@navico.com>. His original comments follow:
This patch adds support for some MLC NAND flashes that place the BB
marker in the LAST page of the bad block rather than the FIRST page used
for SLC NAND and other types of MLC nand.
Lifted from Samsung datasheet for K9LG8G08U0A (1Gbyte MLC NAND):
"
Identifying Initial Invalid Block(s)
All device locations are erased(FFh) except locations where the initial
invalid block(s) information is written prior to shipping. The initial
invalid block(s) status is defined by the 1st byte in the spare area.
Samsung makes sure that the last page of every initial invalid block has
non-FFh data at the column address of 2,048.
...
"
As far as I can tell, this is the same for all Samsung MLC nand, and in
fact the samsung bsp for the processor used in our project (s3c6410)
actually contained a hack similar to this patch but less portable to
enable use of their NAND parts. I discovered this problem when trying to
use a Micron NAND which does not used this layout - I wish samsung would
put their stuff in main-line to avoid this type of problem.
Currently this patch causes all MLC nand with manufacturer codes from
Samsung and ST(Numonyx) to use this alternative location, since these
are the manufactures that I know of that use this layout.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some of the newer MLC devices have a 6-byte ID sequence in which
several field definitions differ from older chips in a manner that is
not backward compatible. For instance:
Samsung K9GAG08U0M (5-byte sequence): ec d5 14 b6 74
4th byte, bits 1:0 encode the page size: 0=1KiB, 1=2KiB, 2=4KiB, 3=8KiB
4th byte, bits 5:4 encode the block size: 0=64KiB, 1=128KiB, ...
4th byte, bit 6 encodes the OOB size: 0=8B/512B, 1=16B/512B
Samsung K9GAG08U0D (6-byte sequence): ec d5 94 29 34 41
4th byte, bits 1:0 encode the page size: 0=2KiB, 1=4KiB, 3=8KiB, 4=rsvd
4th byte, bits 7;5:4 encode the block size: 0=128KiB, 1=256KiB, ...
4th byte, bits 6;3:2 encode the OOB size: 1=128B/page, 2=218B/page
This patch uses the new 6-byte scheme if the following conditions are
all true:
1) The ID code wraps around after exactly 6 bytes
2) Manufacturer is Samsung
3) 6th byte is zero
The patch also extends the maximum OOB size from 128B to 256B.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With gcc 4.4.3 -O2 on MIPS32:
drivers/mtd/chips/cfi_util.c: In function 'cfi_qry_present':
include/linux/mtd/map.h:390: warning: 'r' may be used uninitialized in this function
include/linux/mtd/map.h:375: note: 'r' was declared here
include/linux/mtd/map.h:390: warning: 'r' may be used uninitialized in this function
include/linux/mtd/map.h:375: note: 'r' was declared here
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some SPI masters (ep93xx) have limitations when using the SFRMOUT
signal for the spi device chip select. The SFRMOUT signal is
only asserted as long as the spi transmit fifo contains data. As
soon as the last bit is clocked into the receive fifo it gets
deasserted.
The functions sst25l_status and sst25l_match_device use the API
function spi_write_then_read to write a command to the flash then
read the response back. This API function creates a two part spi
message for the write then read. When this message is transferred
the SFRMOUT signal ends up getting deasserted after the command
phase. This causes the command to get aborted by the device so
the read phase returns invalid data.
By changing sst25l_status and sst25l_match_device to use a single
transfer synchronous message, the SFRMOUT signal stays asserted
during the entire message so the correct data always gets returned.
This change will have no effect on SPI masters which use a chip
select mechanism (GPIO's, etc.) which does stay asserted correctly.
As a bonus, the single transfer synchronous messages complete faster
than multi-part messages.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a driver for OneNAND controller on Samsung SoCs.
Following SoCs are supported: S3C6400, S3C6410, S5PC100 and S5PC110.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some chips fails to identify properly when SYNC_WRITE mode is enabled
(the example is OneNAND on S5PC110 SoC). This patch adds a workaround
for such chips.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a new callback for the underlying drivers, which is
called instead of accessing the buffer ram directly. This callback will
be used by Samsung OneNAND driver to implement DMA transfers on S5PC110
SoC.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends OneNAND core code with support for OneNAND verify
write check. This is done by allocating the buffer for verify read
directly from the core code.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for OneNAND chips that have 4KiB page size.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nothing very important, this just makes git am stop producing warnings.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Factor out old manufacturers and use the generic ones from cfi.h
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for detecting SST 39VF32xxB and 39VF64xxB
chips in CFI mode.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SST 39VF{16,32}xx chips use the 0x0701 command set, fully compatible
with the AMD one. This patch adds support for detecting them in CFI
mode.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Accept values of 2-5 for TopBottom, where the newly-added 4 and 5 values
mean a uniform layout. It does indicate WP layout but we don't handle that.
Also don't say "broken" when swapping erase regions in a top-boot chip.
That got retrospectively documented in the spec.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After looking at AMD's CFI specification [1], both of the extended query
tables are optional. Thus, it looks like relying that at least one of
those tables exist is a bug in cfi_cmdset_0002.
This patch inverts the logic and checks for unlock function pointers before
exiting on error. This approach leaves place to add a call to a fixup
function to try to handle chips compatible with the early AMD specification
from 1995 [2].
[1] http://www.amd.com/us-en/assets/content_type/DownloadableAssets/cfi_r20.pdf
[2] http://noel.feld.cvut.cz/hw/amd/20158a.pdf
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use P_ID_* definitions already in include/linux/mtd/cfi.h instead of the
hardcoded values. Make the code more readable.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SST 39VF160x and 39VF320x chips use vendorname id 0x0701 and alternative
unlock addresses. Add support for them in cfi_probe.c.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make the addresses used to enter Auto Select Mode variable to leave place
for handling chips using non-standard addresses.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move the code to enter Auto Select Mode down to be able to use cfi->cfiq
members to add support for chips using alternative sequence / unlock
addresses.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a kirkwood_nand_init_rnb() call to allow boards which
have RnB line detection to register this instead of a
static delay.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for a board to register a callback to get the state of the
RnB line if it has it attached.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2GB xD card, and 4MB SmartMedia ROM card share same ID, so to make both work
split xD and smartmedia ID tables.
Hardware driver must be able to know which type it handles (and probably just one).
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On i.MX21 SoCs, if the NFC_CONFIG1:NFC_INT_MASK bit is set,
NFC_CONFIG2:NFC_INT always reads out zero, even if an
operation is completed. This patch uses enable_irq and
disable_irq_nosync instead of NFC_CONFIG1:NFC_INT_MASK to
mask NFC interrupts. This allows NFC_CONFIG2:NFC_INT to also
be used to detect operation completion on i.MX21.
The i.MX21 NFC does not signal reset completion using
NFC_CONFIG1:NFC_INT_MASK, so instead reset completion is
tested by checking if NFC_CONFIG2 becomes 0.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows the mxc_nand driver to reset the NAND
flash controller. NFC registers are (re-)set after
completion of the reset, as a reset will have reverted
the NFC registers to their default values.
Signed-off-by: Ivo Clarysse <ivo.clarysse@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is to support custom partitioning schemes for embedded PPC. To use
define your own mtd_part_parser and then add something like:
linux,part-probe = "my_probe", "cmdlinepart";
To the board's dts file.
If linux,part-probe is not specified then this behaves the same as before.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use kzalloc rather than the combination of kmalloc and memset.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,size,flags;
statement S;
@@
-x = kmalloc(size,flags);
+x = kzalloc(size,flags);
if (x == NULL) S
-memset(x, 0, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/denali.c:1427: error: conflicting types for ‘enable_dma’
arch/powerpc/include/asm/dma.h:189: note: previous definition of ‘enable_dma’ was here
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is more work to be done on this but it is basically working now.
Signed-off-by: Jason Roberts <jason.e.roberts@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes a build failure[1] by simply moving the function mtd_to_flctl
beneath the definition of sh_flctl which it uses.
BF introduced by patch
'mtd/nand/sh_flctl: Replace the dangerous mtd_to_flctl macro' (67026418)
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The revision in SVR for MPC5123 is 3. The NFC is the same as MPC5121
revision 2.
Signed-off-by: Steve Deiters <SteveDeiters@basler.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All the SST25L series flash parts have uniform erase sectors. Remove
the extra MTD_DEBUG_LEVEL2 messages showing the eraseregions info
since they could never be shown.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ensure that the flash device is in a quiescent state before rebooting.
The implementation is closely modeled after the cfi_cmdset_0001 reboot
notifier, commit 963a6fb0a0 .
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The pxa32xx_nand driver doesn't support partition tables from the
command line. This patch adds support for it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Moved the debugging message before the call to map_destroy, which frees its
argument. The message is also slightly changed to reflect its new
position.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
del_mtd_device(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The use of a memcpy() during a spinlock operation will cause very long
thread context switch delays if the flash chip bandwidth is low and the
data to be copied large, because a spinlock will disable preemption.
For example: A flash with 6,5 MB/s bandwidth will cause under ubifs,
which request sometimes 128 KiB (the flash erase size), a preemption delay of
20 milliseconds. High priority threads will not be served during this
time, regardless whether this threads access the flash or not. This behavior
breaks real time.
The patch changes all the use of spin_lock operations for xxxx->mutex
into mutex operations, which is exact what the name says and means.
I have checked the code of the drivers and there is no use of atomic
pathes like interrupt or timers. The mtdoops facility will also not be used
by this drivers. So it is dave to replace the spin_lock against mutex.
There is no performance regression since the mutex is normally not
acquired.
Changelog:
06.03.2010 First release
26.03.2010 Fix mutex[1] issue and tested it for compile failure
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Functions omap2_onenand_write_bufferram() and omap3_onenand_write_bufferram()
map the write buffer and store the returned handle in variable dma_src. However,
when DMA unmap is done, variable dma_dst is used instead of the correct dma_src.
This patch fixes them to use the correct DMA buffer.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert all magic numbers into appropriate defines, and move the defines
out of the global namespace and into this one driver. No other driver
needs to care about the MMR layout anyways.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do not need these names. Moreover, there are spelling typos
there: "nansin" instead of "nandsim".
This patch is just a clean up, no functional changes.
Reported-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
include/linux/mtd/mtdram.h:6: ERROR: code indent should use tabs where possible
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
