The computed result of I40E_MAX_VSI_QP * I40E_VIRTCHNL_SUPPORTED_QTYPES
is used more than three times in function i40e_config_irq_link_list.
Simply declare a local variable to store it to improve readability.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- When the I2C is busy, the PHY reads are delayed. The firmware will
return EGAIN in these cases with an expectation that the SW will
trigger the reads again
- This patch retries the operation for a maximum period of 500ms
Signed-off-by: Jayaprakash Shanmugam <jayaprakash.shanmugam@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The find_first_bit function will return the size passed to search
if the first set bit is not found. This patch adds the check in case
that happens as the return value would be used as the index in an array
and that would have caused the out-of-bounds access.
Detected by CoverityScan, CID 1295969 Out-of-bounds access
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recently, the kernel gained support for enabling XPS and QoS at the
same time. Thus, we no longer need to worry about the number of
traffic classes when enabling XPS.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double the number of descriptors we'll bundle into one tail bump when
receiving. Empirical testing has shown that we reduce CPU utilization
and don't appear to reduce throughput or packet rate. 32 seems to be the
sweet spot, as it's half the default polling budget, so we'd essentially
reduce from 4 tail writes when polling down to 2. Increasing this up to
64 appears to have negative impacts as it may become possible that we
don't bump the tail each time we get polled, which could cause a long
delay between returning descriptors to the hardware.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware only fetches descriptors on cachelines of 8, essentially
ignoring the lower 3 bits of the tail register. Thus, it is pointless to
bump tail by an unaligned access as the hardware will ignore some of the
new descriptors we allocated. Thus, it's ideal if we can ensure tail
writes are always aligned to 8.
At first, it seems like we'd already do this, since we allocate
descriptors in batches which are a multiple of 8. Since we'd always
increment by a multiple of 8, it seems like the value should always be
aligned.
However, this ignores allocation failures. If we fail to allocate
a buffer, our tail register will become unaligned. Once it has become
unaligned it will essentially be stuck unaligned until a buffer
allocation happens to fail at the exact amount necessary to re-align it.
We can do better, by simply rounding down the number of buffers we're
about to allocate (cleaned_count) such that "next_to_clean
+ cleaned_count" is rounded to the nearest multiple of 8.
We do this by calculating how far off that value is and subtracting it
from the cleaned_count. This essentially defers allocation of buffers if
they're going to be ignored by hardware anyways, and re-aligns our
next_to_use and tail values after a failure to allocate a descriptor.
This calculation ensures that we always align the tail writes in a way
the hardware expects and don't unnecessarily allocate buffers which
won't be fetched immediately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The lrxq thresh value tells hardware to immediately interrupt when there
are fewer than N*64 packets left in the ring.
Counter intuitively, empirical testing has shown that decreasing this
value from 2 to 1, and thus changing from an immediate interrupt at
fewer than 128 descriptors down to 64 descriptors causes a small
increase in the maximum total packets per second we can receive. This
increase occurs even when we're polling with interrupts masked, as the
hardware must still handle interrupts internally even if we've disabled
them in software.
Also reduce the value for any VFs we allocate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the past we changed driver behavior to not clear the PBA when
re-enabling interrupts. This change was motivated by the flawed belief
that clearing the PBA would cause a lost interrupt if a receive
interrupt occurred while interrupts were disabled.
According to empirical testing this isn't the case. Additionally, the
data sheet specifically says that we should set the CLEARPBA bit when
re-enabling interrupts in a polling setup.
This reverts commit 40d72a5098 ("i40e/i40evf: don't lose interrupts")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ITR register expects to be programmed in units of 2 microseconds.
Because of this, all of the drivers I40E_ITR_* constants are in terms of
this 2 microsecond register.
Unfortunately, the rx_itr_default value is expected to be programmed in
microseconds.
Effectively the driver defaults to an ITR value of half the expected
value (in terms of minimum microseconds between interrupts).
Fix this by changing the default values to be calculated using
ITR_REG_TO_USEC macro which indicates that we're converting from the
register units into microseconds.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Due to the asynchronous nature in which mac filters are added and
deleted, there exists a bug in which filters are erroneously removed if
removed then added again quickly.
The events are as such:
- filter marked for removal
- same filter is re-added before watchdog that cleans up filters
- we skip re-adding the filter because we have it already in the
list
- watchdog filter cleanup kicks off and filter is removed
So when we were re-adding the same filter, it didn't actually get added
because it already existed in the list, but was marked for removal and
had yet to actually be removed.
This patch fixes the issue by making sure that when adding a filter, if
we find it already existing in our list, make sure it is not marked to
be removed.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces hash_for_each function with hash_for_each_safe
when calling __i40e_del_filter. The hash_for_each_safe function is
the right one to use when iterating over a hash table to safely remove
a hash entry. Otherwise, incorrect values may be read from freed memory.
Detected by CoverityScan, CID 1402048 Read from pointer after free
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we don't yet have more than 32 flags, we'll use a u32 for both the
hw_features and flag field. Should we gain more flags in the future, we
may need to convert to a u64 or separate flags out into two fields.
This was overlooked in the previous commit 2781de2134c4 ("i40e/i40evf:
organize and re-number feature flags"), where the feature flag was not
converted form u64 to u32.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet says:
====================
ipv6: addrlabel: avoid dirtying ip6addrlbl_entry
The refcount on ip6addrlbl_entry is only used to make sure ip6addrlbl_entry
does not disappear while ip6addrlbl_get() is allocating an skb.
We can instead allocate skb first, then use RCU, so that we no longer need
to refcount these structures.
====================
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After previous patch ("ipv6: addrlabel: rework ip6addrlbl_get()")
we can remove the refcount from struct ip6addrlbl_entry,
since it is no longer elevated in p6addrlbl_get()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we allocate skb before the lookup, we can use RCU
without the need of ip6addrlbl_hold()
This means that the following patch can get rid of refcounting.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
Fix mlx4 static checker warnings
This patchset contains fixes for static checker warnings
in the mlx4 Core and Eth drivers.
Patch 1 fixes an actual bug discovered by the checker.
Patches 2 and 3 fix the warnings without functional changes.
Series generated against net-next commit:
c49c777f9c qed: Delete redundant check on dcb_app priority
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In TX data-path, we intentionally do not byte-swap, as documented
in code and in the cited commit log.
This fixes sparse warning:
en_tx.c:720:23: warning: incorrect type in argument 1 (different base types)
en_tx.c:720:23: expected unsigned int [unsigned] [usertype] <noident>
en_tx.c:720:23: got restricted __be32 [usertype] doorbell_qpn
Fixes: 492f5add4b ("net/mlx4_en: Doorbell is byteswapped in Little Endian archs")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following SPARSE warning, in MLX4_GET() macro:
drivers/net/ethernet/mellanox/mlx4/fw.c:233:9: warning: cast to restricted __be64
Fixes: 17d5ceb6e4 ("net/mlx4_core: Fix unaligned accesses")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should take care of the endianness before assigning to params2 field.
Fixes: 53f33ae295 ("net/mlx4_core: Port aggregation upper layer interface")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 0day kbuild robot reports following crash:
BUG: unable to handle kernel NULL pointer dereference at 00000004
IP: tb_property_find+0xe/0x41
*pde = 00000000
Oops: 0000 [#1]
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.0-rc1-00741-ge69b6c0 #412
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
task: 89c80000 task.stack: 89c7c000
EIP: tb_property_find+0xe/0x41
EFLAGS: 00210246 CPU: 0
EAX: 00000000 EBX: 7a368f47 ECX: 00000044 EDX: 7a368f47
ESI: 8851d340 EDI: 7a368f47 EBP: 89c7df0c ESP: 89c7defc
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 027a2000 CR4: 00000690
Call Trace:
tb_register_property_dir+0x49/0xb9
? cdc_mbim_driver_init+0x1b/0x1b
tbnet_init+0x77/0x9f
? cdc_mbim_driver_init+0x1b/0x1b
do_one_initcall+0x7e/0x145
? parse_args+0x10c/0x1b3
? kernel_init_freeable+0xbe/0x159
kernel_init_freeable+0xd1/0x159
? rest_init+0x110/0x110
kernel_init+0xd/0xd0
ret_from_fork+0x19/0x30
The reason is that both Thunderbolt bus and thunderbolt-net are build
into the kernel image, and the latter is linked first because
drivers/net comes before drivers/thunderbolt. Since both use
module_init() thunderbolt-net ends up calling Thunderbolt bus functions
too early triggering the above crash.
Fix this by moving Thunderbolt bus initialization to happen earlier to
make sure all the data structures are ready when Thunderbolt service
drivers are initialized. To be on the safe side also add a check for
properly initialized xdomain_property_dir to tb_register_property_dir().
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
per cpu allocations are already zeroed, no need to clear them again.
Fixes: d52d3997f8 ("ipv6: Create percpu rt6_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon says:
====================
qed: Add iWARP support for unaligned MPA packets
This patch series adds support for handling unaligned MPA packets.
(FPDUs split over more than one tcp packet).
When FW detects a packet is unaligned it fowards the packet to
the driver via a light l2 dedicated connection. The driver then
stores this packet until the remainder of the packet is received.
Once the driver reconstructs the full FPDU, it sends it down
to fw via the ll2 connection. Driver also breaks down any packed
PDUs into separate packets for FW.
Patches 1-6 are all slight modifications to ll2 to support additional
requirements for the unaligned MPA ll2 client.
Patch 7 opens the additional ll2 connection for iWARP.
Patches 8-12 contain the algorithm for aligning packets.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We continue to maintain a maximum of three buffers per fpdu, to ensure
that there are enough buffers for additional unaligned mpa packets.
To support this, if a fpdu is split over more than two tcp packets, we
use an intermediate buffer to copy the data to the previous buffer, then
we can release the data. We need an intermediate buffer as the initial
buffer partial packet could be located at the end of the packet, not
leaving room for additional data. This is a corner case, and will usually
not be the case.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a special case where an MPA header is split over to tcp
packets, in this case we need to wait for the next packet to
get the fpdu length. We use the incomplete_bytes to mark this
fpdu as a "special" one which requires updating the length with
the next packet
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When posting a packet on the ll2 tx, we can provide a cookie that
will be returned upon tx completion. This cookie is the ll2 iwarp buffer
which is then reposted to the rx ring. Part of the unaligned mpa flow
is determining when a buffer can be reposted. Each buffer needs to be
sent only once as a cookie for on the tx ring. In packed fpdu case, only
the last packet will be sent with the buffer, meaning we need to handle the
case that a cookie can be NULL on tx complete. In addition, when a fpdu
splits over two buffers, but there are no more fpdus on the second buffer,
two buffers need to be provided as a cookie. To avoid changing the ll2
interface to provide two cookies, we introduce a piggy buf pointer,
relevant for iWARP only, that holds a pointer to a second buffer that
needs to be released during tx completion.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fpdu data structure is preallocated per connection.
Each connection stores the current status of the connection:
either nothing pending, or there is a partial fpdu that is waiting for
the rest of the fpdu (incomplete bytes != 0).
The same structure is also used for splitting a packet when there are
packed fpdus. The structure is initialized with all data required
for sending the fpdu back to the FW. A fpdu will always be spanned across
a maximum of 3 tx bds. One for the header, one for the partial fdpu
received and one for the remainder (unaligned) packet.
In case of packed fpdu's, two fragments are used, one for the header
and one for the data.
Corner cases are not handled in the patch for clarity, and will be added
as a separate patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mpa buff is a descriptor for iwarp ll2 buffers that contains
additional information required for aligining fpdu's.
In some cases, an additional packet will arrive which will complete
the alignment of a fpdu, but we won't be able to post the fpdu due to
insufficient place on the tx ring. In this case we can't loose the data
and require storing it for later. Processing is therefore done
in two places, during rx completion, where we initialize a mpa buffer
descriptor and add it to the pending list, and during tx-completion, since
we free up an entry in the tx chain we can process any pending mpa packets.
The mpa buff descriptors are pre-allocated since we have to ensure that
we won't reach a state where we can't store an incoming unaligned packet.
All packets received on the ll2 MUST be processed by the driver at some
stage. Since they are preallocated, we hold a free list.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds only the establishment and termination of the
ll2 connection that handles unaligned MPA packets.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For iWARP unaligned MPA flow, a slowpath event of flushing an
MPA connection that entered an unaligned state is required.
The flush ramrod is received on the ll2 queue, and a pre-registered
callback function is called to handle the flush event.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is sent back to iWARP FW via the tx ll2 connection
the FW needs to know the source of the packet. Whether it is
OOO or unaligned MPA related. Since OOO is implemented entirely
inside the ll2 code (and shared with iSCSI), packets are marked
as IN_ORDER inside the ll2 code. For unaligned mpa the value
will be determined in the iWARP code and sent on the pkt->vlan
field.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enable_ip_cksum, enable_l4_cksum, calc_ip_len were added in
commit stated below but not passed through to FW. This was OK
until now as it wasn't used, but is required for the iWARP
unaligned flow
Fixes:7c7973b2ae27 ("qed: LL2 to use packed information for tx")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option of sending a packet on the ll2 and dropping it exists in
hardware and was not used until now, thus not exposed.
The iWARP unaligned MPA flow requires this functionality for
flushing the tx queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When more than one ll2 queue is opened ( that is not an OOO queue )
ll2 code does not have enough information to determine whether
the queue is the main one or not, so a new field is added to the
acquire input data to expose the control of determining whether
the queue is the main queue or a secondary queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP uses 3 ll2 connections, the maximum number of bds is known
during connection setup. This patch modifies the static array in
the ll2_tx_packet descriptor to be a flexible array and
significantlly reduces memory size.
In addition, some redundant fields in the ll2_tx_packet were
removed, which also contributed to decreasing the descriptor size.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Offload bridge device mrouter
Yotam says:
Similarly to a bridged port, the bridge device itself can be configured by
the user to be an mrouter port. In this case, all multicast traffic should
be forwarded to it. Make the mlxsw Spectrum driver offload these directives
to the Spectrum hardware.
Patches 1 and 2 add a new switchdev notification for bridge device mrouter
port status and make the bridge module notify about it.
Patches 3-5 change the mlxsw Spectrum driver to handle these notifications
by adding the Spectrum router port to the bridge MDB entries.
v1->v2:
- patch1:
- Don't add the MDB_RTR_TYPE_TEMP state and use the timer_pending to
distinguish between learning-on and learning-off states
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER port attribute switchdev
notification.
To do that, add the mrouter flag to struct mlxsw_sp_bridge_device, which
indicates whether the bridge device was set to be mrouter port. This field
is set when:
- A new bridge is created, where the value is taken from the kernel
bridge value.
- A switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent.
In addition, change the bridge MID entries to include the router port when
the bridge device is configured to be mrouter port. The MID entries are
updated in the following cases:
- When a new MID entry is created, update the router port according to the
bridge mrouter state.
- When a SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent, update all
the bridge's MID entries.
This is aligned with the case where a bridge slave is configured to be
mrouter port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum, MDB entries point to MID entries, that indicate which ports a
packet should be forwarded to. Add the support in creating MID entries that
forward the packet to the Spectrum router port.
This will be later used to handle the bridge mrouter port switchdev
notifications.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum hardware, the router port is a virtual port that is the gateway
to the routing mechanism. Hence, in order for a packet to be L3 forwarded,
it must first be L2 forwarded to the router port inside the hardware.
Further patches in this patchset are going to introduce support in bridge
device used as an mrouter port. In this case, the router port index will be
needed in order to update the MDB entries to include the router port. Thus,
export the mlxsw_sp_router_port function, which returns the index of the
Spectrum router port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an access function that, given a bridge netdevice, returns whether the
bridge device is currently an mrouter or not. The function uses the already
existing br_multicast_is_router function to check that.
This function is needed in order to allow ports that join an already
existing bridge to know the current mrouter state of the bridge device.
Together with the bridge device mrouter ports switchdev notifications, it
is possible to have full offloading of the semantics of the bridge device
mcast router state.
Due to the fact that the bridge multicast router status can change in
packet RX path, take the multicast_router bridge spinlock to protect the
read.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER switchdev notification type, used
to indicate whether the bridge is or isn't mrouter. Notify when the bridge
changes its state, similarly to the already existing bridged port mrouter
notifications.
The notification uses the switchdev_attr.u.mrouter boolean flag to indicate
the current bridge mrouter status. Thus, it only indicates whether the
bridge is currently used as an mrouter or not, and does not indicate the
exact mrouter state of the bridge (learning, permanent, etc.).
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: bpf ABIv2 and multi port
This series migrates our eBPF offload from old PoC firmware to
a redesigned, faster and more feature rich FW. Marking support
is dropped for now. We have to teach the JIT about encoding
local memory accesses (one of NFP memory types). There is also
code to populate the ECC of instructions (PoC had ECC protection
on instruction store disabled). There is also a minor ld_field
fix and all 64 bit shifts can now be encoded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ld_field instruction is a bit special because the encoding uses
two source registers and one of them becomes the output. We do
need to pass the dst register to our encoding helpers though,
otherwise the "write both banks" flag will not be observed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device expects the instructions in little endian. Make sure we
byte swap on big endian hosts.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to append up to 8 nops after last instruction to make
sure the CPU will not fetch garbage instructions with invalid
ECC if the code store was not initialized.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the initial PoC firmware I simply disabled ECC on the instruction
store. Do the ECC calculation for generated instructions in the driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datapath ABI version 2 stores the packet information in LMEM
instead of NNRs. We also have strict restrictions on which
GPRs we can use. Only GPRs 0-23 are reserved for BPF.
Adjust the static register locations and "ABI" registers.
Note that packet length is packed with other info so we have
to extract it into one of the scratch registers, OTOH since
LMEM can be used in restricted operands we don't have to
extract packet pointer.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most instructions have special fields which allow switching
between base and extended Local Memory pointers. Introduce
those to register encoding, we will use the extra LM pointers
to access high addresses of the stack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP LMEM is a large, indirectly accessed register file. There
are two basic indirect access registers. Each access operation
may either use offset (up to 8 or 16 words) or perform post
decrement/increment.
Add encodings of LMEM indexes as instruction operands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to add longer OP_* defines, move the values away.
Purely whitespace commit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Temporarily drop support for skb->mark. We are primarily focusing
on XDP offload, and implementing skb->mark on the new datapath has
lower priority.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
