A node that has the MRA role, it can behave as MRM or MRC.
Initially it starts as MRM and sends MRP_Test frames on both ring ports.
If it detects that there are MRP_Test send by another MRM, then it
checks if these frames have a lower priority than itself. In this case
it would send MRP_Nack frames to notify the other node that it needs to
stop sending MRP_Test frames.
If it receives a MRP_Nack frame then it stops sending MRP_Test frames
and starts to behave as a MRC but it would continue to monitor the
MRP_Test frames send by MRM. If at a point the MRM stops to send
MRP_Test frames it would get the MRM role and start to send MRP_Test
frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each MRP instance has a priority, a lower value means a higher priority.
The priority of MRP instance is stored in MRP_Test frame in this way
all the MRP nodes in the ring can see other nodes priority.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When neighbor suppression is enabled the bridge device might reply to
Neighbor Solicitation (NS) messages on behalf of remote hosts.
In case the NS message includes the "Source link-layer address" option
[1], the bridge device will use the specified address as the link-layer
destination address in its reply.
To avoid an infinite loop, break out of the options parsing loop when
encountering an option with length zero and disregard the NS message.
This is consistent with the IPv6 ndisc code and RFC 4886 which states
that "Nodes MUST silently discard an ND packet that contains an option
with length zero" [2].
[1] https://tools.ietf.org/html/rfc4861#section-4.3
[2] https://tools.ietf.org/html/rfc4861#section-4.6
Fixes: ed842faeb2 ("bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alla Segal <allas@mellanox.com>
Tested-by: Alla Segal <allas@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_umem.c had overlapping changes between the 64-bit math fix
for the calculation of npgs and the removal of the zerocopy
memory type which got rid of the chunk_size_nohdr member.
The mlx5 Kconfig conflict is a case where we just take the
net-next copy of the Kconfig entry dependency as it takes on
the ESWITCH dependency by one level of indirection which is
what the 'net' conflicting change is trying to ensure.
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang-10 and clang-11 run into a corner case of the register
allocator on 32-bit ARM, leading to excessive stack usage from
register spilling:
net/bridge/br_multicast.c:2422:6: error: stack frame size of 1472 bytes in function 'br_multicast_get_stats' [-Werror,-Wframe-larger-than=]
Work around this by marking one of the internal functions as
noinline_for_stack.
Link: https://bugs.llvm.org/show_bug.cgi?id=45802#c9
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the MRP netlink interface. Before, each attribute
represented a binary structure which made it hard to be extended.
Therefore update the MRP netlink interface such that each existing
attribute to be a nested attribute which contains the fields of the
binary structures.
In this way the MRP netlink interface can be extended without breaking
the backwards compatibility. It is also using strict checking for
attributes under the MRP top attribute.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was reported by syzbot. When the function br_mrp_parse was
called with a valid net_bridge_port, the net_bridge was an invalid
pointer. Therefore the check br->stp_enabled could pass/fail
depending where it was pointing in memory.
The fix consists of setting the net_bridge pointer if the port is a
valid pointer.
Reported-by: syzbot+9c6f0f1f8e32223df9a4@syzkaller.appspotmail.com
Fixes: 6536993371 ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, using the bridge reject target with tagged packets
results in untagged packets being sent back.
Fix this by mirroring the vlan id as well.
Fixes: 85f5b3086a ("netfilter: bridge: add reject support")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When a MRP instance is deleted, then restore the port according to the
bridge state. If the bridge is up then the ports will be in forwarding
state otherwise will be in disabled state.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allow to have the same net bridge port part of multiple MRP
rings. Therefore add a check if the port is used already in a different
MRP. In that case return failure.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8db0a2ee2c ("net: bridge: reject DSA-enabled master netdevices
as bridge members") added a special check in br_if.c in order to check
for a DSA master network device with a tagging protocol configured. This
was done because back then, such devices, once enslaved in a bridge
would become inoperative and would not pass DSA tagged traffic anymore
due to br_handle_frame returning RX_HANDLER_CONSUMED.
But right now we have valid use cases which do require bridging of DSA
masters. One such example is when the DSA master ports are DSA switch
ports themselves (in a disjoint tree setup). This should be completely
equivalent, functionally speaking, from having multiple DSA switches
hanging off of the ports of a switchdev driver. So we should allow the
enslaving of DSA tagged master network devices.
Instead of the regular br_handle_frame(), install a new function
br_handle_frame_dummy() on these DSA masters, which returns
RX_HANDLER_PASS in order to call into the DSA specific tagging protocol
handlers, and lift the restriction from br_add_if.
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netpoll_send_skb() callers seem to leak skb if
the np pointer is NULL. While this should not happen, we
can make the code more robust.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NL_SET_ERR_MSG_MOD macro is used to report a string describing an
error message to userspace via the netlink extended ACK structure. It
should not have a trailing newline.
Add a cocci script which catches cases where the newline marker is
present. Using this script, fix the handful of cases which accidentally
included a trailing new line.
I couldn't figure out a way to get a patch mode working, so this script
only implements context, report, and org.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
net/bridge/br_private.h:1334:8-9: WARNING: return of 0/1 in function
'br_mrp_enabled' with return type bool
Fixes: 6536993371 ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-01 (v2)
The following pull-request contains BPF updates for your *net-next* tree.
We've added 61 non-merge commits during the last 6 day(s) which contain
a total of 153 files changed, 6739 insertions(+), 3367 deletions(-).
The main changes are:
1) pulled work.sysctl from vfs tree with sysctl bpf changes.
2) bpf_link observability, from Andrii.
3) BTF-defined map in map, from Andrii.
4) asan fixes for selftests, from Andrii.
5) Allow bpf_map_lookup_elem for SOCKMAP and SOCKHASH, from Jakub.
6) production cloudflare classifier as a selftes, from Lorenz.
7) bpf_ktime_get_*_ns() helper improvements, from Maciej.
8) unprivileged bpftool feature probe, from Quentin.
9) BPF_ENABLE_STATS command, from Song.
10) enable bpf_[gs]etsockopt() helpers for sock_ops progs, from Stanislav.
11) enable a bunch of common helpers for cg-device, sysctl, sockopt progs,
from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
User space can request to delete a range of VLANs from a bridge slave in
one netlink request. For each deleted VLAN the FDB needs to be traversed
in order to flush all the affected entries.
If a large range of VLANs is deleted and the number of FDB entries is
large or the FDB lock is contented, it is possible for the kernel to
loop through the deleted VLANs for a long time. In case preemption is
disabled, this can result in a soft lockup.
Fix this by adding a schedule point after each VLAN is deleted to yield
the CPU, if needed. This is safe because the VLANs are traversed in
process context.
Fixes: bdced7ef78 ("bridge: support for multiple vlans and vlan ranges in setlink and dellink requests")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Tested-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not possible to have the MRP and STP running at the same time on the
bridge, therefore add check when enabling the STP to check if MRP is already
enabled. In that case return error.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To integrate MRP into the bridge, the bridge needs to do the following:
- detect if the MRP frame was received on MRP ring port in that case it would be
processed otherwise just forward it as usual.
- enable parsing of MRP
- before whenever the bridge was set up, it would set all the ports in
forwarding state. Add an extra check to not set ports in forwarding state if
the port is an MRP ring port. The reason of this change is that if the MRP
instance initially sets the port in blocked state by setting the bridge up it
would overwrite this setting.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement netlink interface to configure MRP. The implementation
will do sanity checks over the attributes and then eventually call the MRP
interface.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MRP API.
In case the HW can't generate MRP Test frames then the SW will try to generate
the frames. In case that also the SW will fail in generating the frames then a
error is return to the userspace. The userspace is responsible to generate all
the other MRP frames regardless if the test frames are generated by HW or SW.
The forwarding/termination of MRP frames is happening in the kernel and is done
by the MRP instance. The userspace application doesn't do the forwarding.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the MRP api for switchdev.
These functions will just eventually call the switchdev functions:
switchdev_port_obj_add/del and switchdev_port_attr_set.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the MRP interface.
This interface is used by the netlink to update the MRP instances and by the MRP
to make the calls to switchdev to offload it to HW.
It defines an MRP instance 'struct br_mrp' which is a list of MRP instances.
Which will be part of the 'struct net_bridge'. Each instance has 2 ring ports,
a bridge and an ID.
In case the HW can't generate MRP Test frames then the SW will generate those.
br_mrp_add - adds a new MRP instance.
br_mrp_del - deletes an existing MRP instance. Each instance has an ID(ring_id).
br_mrp_set_port_state - changes the port state. The port can be in forwarding
state, which means that the frames can pass through or in blocked state which
means that the frames can't pass through except MRP frames. This will
eventually call the switchdev API to notify the HW. This information is used
also by the SW bridge to know how to forward frames in case the HW doesn't
have this capability.
br_mrp_set_port_role - a port role can be primary or secondary. This
information is required to be pushed to HW in case the HW can generate
MRP_Test frames. Because the MRP_Test frames contains a file with this
information. Otherwise the HW will not be able to generate the frames
correctly.
br_mrp_set_ring_state - a ring can be in state open or closed. State open means
that the mrp port stopped receiving MRP_Test frames, while closed means that
the mrp port received MRP_Test frames. Similar with br_mrp_port_role, this
information is pushed in HW because the MRP_Test frames contain this
information.
br_mrp_set_ring_role - a ring can have the following roles MRM or MRC. For the
role MRM it is expected that the HW can terminate the MRP frames, notify the
SW that it stopped receiving MRP_Test frames and trapp all the other MRP
frames. While for MRC mode it is expected that the HW can forward the MRP
frames only between the MRP ports and copy MRP_Topology frames to CPU. In
case the HW doesn't support a role it needs to return an error code different
than -EOPNOTSUPP.
br_mrp_start_test - this starts/stops the generation of MRP_Test frames. To stop
the generation of frames the interval needs to have a value of 0. In this case
the userspace needs to know if the HW supports this or not. Not to have
duplicate frames(generated by HW and SW). Because if the HW supports this then
the SW will not generate anymore frames and will expect that the HW will
notify when it stopped receiving MRP frames using the function
br_mrp_port_open.
br_mrp_port_open - this function is used by drivers to notify the userspace via
a netlink callback that one of the ports stopped receiving MRP_Test frames.
This function is called only when the node has the role MRM. It is not
supposed to be called from userspace.
br_mrp_port_switchdev_add - this corresponds to the function br_mrp_add,
and will notify the HW that a MRP instance is added. The function gets
as parameter the MRP instance.
br_mrp_port_switchdev_del - this corresponds to the function br_mrp_del,
and will notify the HW that a MRP instance is removed. The function
gets as parameter the ID of the MRP instance that is removed.
br_mrp_port_switchdev_set_state - this corresponds to the function
br_mrp_set_port_state. It would notify the HW if it should block or not
non-MRP frames.
br_mrp_port_switchdev_set_port - this corresponds to the function
br_mrp_set_port_role. It would set the port role, primary or secondary.
br_mrp_switchdev_set_role - this corresponds to the function
br_mrp_set_ring_role and would set one of the role MRM or MRC.
br_mrp_switchdev_set_ring_state - this corresponds to the function
br_mrp_set_ring_state and would set the ring to be open or closed.
br_mrp_switchdev_send_ring_test - this corresponds to the function
br_mrp_start_test. This will notify the HW to start or stop generating
MRP_Test frames. Value 0 for the interval parameter means to stop generating
the frames.
br_mrp_port_open - this function is used to notify the userspace that the port
lost the continuity of MRP Test frames.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new port attribute, IFLA_BRPORT_MRP_RING_OPEN, which allows
to notify the userspace when the port lost the continuite of MRP frames.
This attribute is set by kernel whenever the SW or HW detects that the ring is
being open or closed.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To integrate MRP into the bridge, first the bridge needs to be aware of ports
that are part of an MRP ring and which rings are on the bridge.
Therefore extend bridge interface with the following:
- add new flag(BR_MPP_AWARE) to the net bridge ports, this bit will be
set when the port is added to an MRP instance. In this way it knows if
the frame was received on MRP ring port
- add new flag(BR_MRP_LOST_CONT) to the net bridge ports, this bit will be set
when the port lost the continuity of MRP Test frames.
- add a list of MRP instances
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the option BRIDGE_MRP to allow to build in or not MRP support.
The default value is N.
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having all the sysctl handlers deal with user pointers, which
is rather hairy in terms of the BPF interaction, copy the input to and
from userspace in common code. This also means that the strings are
always NUL-terminated by the common code, making the API a little bit
safer.
As most handler just pass through the data to one of the common handlers
a lot of the changes are mechnical.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that we have a nested tunnel info attribute we can add a separate
one for the tunnel command and require it explicitly from user-space. It
must be one of RTM_SETLINK/DELLINK. Only RTM_SETLINK requires a valid
tunnel id, DELLINK just removes it if it was set before. This allows us
to have all tunnel attributes and control in one place, thus removing
the need for an outside vlan info flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While discussing the new API, Roopa mentioned that we'll be adding more
tunnel attributes and options in the future, so it's better to make it a
nested attribute, since this is still in net-next we can easily change it
and nest the tunnel id attribute under BRIDGE_VLANDB_ENTRY_TUNNEL_INFO.
The new format is:
[BRIDGE_VLANDB_ENTRY]
[BRIDGE_VLANDB_ENTRY_TUNNEL_INFO]
[BRIDGE_VLANDB_TINFO_ID]
Any new tunnel attributes can be nested under
BRIDGE_VLANDB_ENTRY_TUNNEL_INFO.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for vlan stats to be included when dumping vlan
information. We have to dump them only when explicitly requested (thus the
flag below) because that disables the vlan range compression and will make
the dump significantly larger. In order to request the stats to be
included we add a new dump attribute called BRIDGE_VLANDB_DUMP_FLAGS which
can affect dumps with the following first flag:
- BRIDGE_VLANDB_DUMPF_STATS
The stats are intentionally nested and put into separate attributes to make
it easier for extending later since we plan to add per-vlan mcast stats,
drop stats and possibly STP stats. This is the last missing piece from the
new vlan API which makes the dumped vlan information complete.
A dump request which should include stats looks like:
[BRIDGE_VLANDB_DUMP_FLAGS] |= BRIDGE_VLANDB_DUMPF_STATS
A vlandb entry attribute with stats looks like:
[BRIDGE_VLANDB_ENTRY] = {
[BRIDGE_VLANDB_ENTRY_STATS] = {
[BRIDGE_VLANDB_STATS_RX_BYTES]
[BRIDGE_VLANDB_STATS_RX_PACKETS]
...
}
}
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Use nf_flow_offload_tuple() to fetch flow stats, from Paul Blakey.
2) Add new xt_IDLETIMER hard mode, from Manoj Basapathi.
Follow up patch to clean up this new mode, from Dan Carpenter.
3) Add support for geneve tunnel options, from Xin Long.
4) Make sets built-in and remove modular infrastructure for sets,
from Florian Westphal.
5) Remove unused TEMPLATE_NULLS_VAL, from Li RongQing.
6) Statify nft_pipapo_get, from Chen Wandun.
7) Use C99 flexible-array member, from Gustavo A. R. Silva.
8) More descriptive variable names for bitwise, from Jeremy Sowden.
9) Four patches to add tunnel device hardware offload to the flowtable
infrastructure, from wenxu.
10) pipapo set supports for 8-bit grouping, from Stefano Brivio.
11) pipapo can switch between nibble and byte grouping, also from
Stefano.
12) Add AVX2 vectorized version of pipapo, from Stefano Brivio.
13) Update pipapo to be use it for single ranges, from Stefano.
14) Add stateful expression support to elements via control plane,
eg. counter per element.
15) Re-visit sysctls in unprivileged namespaces, from Florian Westphal.
15) Add new egress hook, from Lukas Wunner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for manipulating vlan/tunnel mappings. The
tunnel ids are globally unique and are one per-vlan. There were two
trickier issues - first in order to support vlan ranges we have to
compute the current tunnel id in the following way:
- base tunnel id (attr) + current vlan id - starting vlan id
This is in line how the old API does vlan/tunnel mapping with ranges. We
already have the vlan range present, so it's redundant to add another
attribute for the tunnel range end. It's simply base tunnel id + vlan
range. And second to support removing mappings we need an out-of-band way
to tell the option manipulating function because there are no
special/reserved tunnel id values, so we use a vlan flag to denote the
operation is tunnel mapping removal.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new option - BRIDGE_VLANDB_ENTRY_TUNNEL_ID which is used to dump
the tunnel id mapping. Since they're unique per vlan they can enter a
vlan range if they're consecutive, thus we can calculate the tunnel id
range map simply as: vlan range end id - vlan range start id. The
starting point is the tunnel id in BRIDGE_VLANDB_ENTRY_TUNNEL_ID. This
is similar to how the tunnel entries can be created in a range via the
old API (a vlan range maps to a tunnel range).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan tunnel code changes vlan options, it shouldn't touch port or
bridge options so we can constify the port argument. This would later help
us to re-use these functions from the vlan options code.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more appropriate name as it shows the intent of why we need to
check the options' state. It also allows us to give meaning to the two
arguments of the function: the first is the current vlan (v_curr) being
checked if it could enter the range ending in the second one (range_end).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
Lastly, fix checkpatch.pl warning
WARNING: __aligned(size) is preferred over __attribute__((aligned(size)))
in net/bridge/netfilter/ebtables.c
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In br_dev_xmit() we perform vlan filtering in br_allowed_ingress() but
if the packet has the vlan header inside (e.g. bridge with disabled
tx-vlan-offload) then the vlan filtering code will use skb_vlan_untag()
to extract the vid before filtering which in turn calls pskb_may_pull()
and we may end up with a stale eth pointer. Moreover the cached eth header
pointer will generally be wrong after that operation. Remove the eth header
caching and just use eth_hdr() directly, the compiler does the right thing
and calculates it only once so we don't lose anything.
Fixes: 057658cb33 ("bridge: suppress arp pkts on BR_NEIGH_SUPPRESS ports")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_entry_rcu() has built-in RCU and lock checking.
Pass cond argument to list_for_each_entry_rcu() to silence
false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled
by default.
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first per-vlan option added is state, it is needed for EVPN and for
per-vlan STP. The state allows to control the forwarding on per-vlan
basis. The vlan state is considered only if the port state is forwarding
in order to avoid conflicts and be consistent. br_allowed_egress is
called only when the state is forwarding, but the ingress case is a bit
more complicated due to the fact that we may have the transition between
port:BR_STATE_FORWARDING -> vlan:BR_STATE_LEARNING which should still
allow the bridge to learn from the packet after vlan filtering and it will
be dropped after that. Also to optimize the pvid state check we keep a
copy in the vlan group to avoid one lookup. The state members are
modified with *_ONCE() to annotate the lockless access.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for option modification of single vlans and
ranges. It allows to only modify options, i.e. skip create/delete by
using the BRIDGE_VLAN_INFO_ONLY_OPTS flag. When working with a range
option changes we try to pack the notifications as much as possible.
v2: do full port (all vlans) notification only when creating/deleting
vlans for compatibility, rework the range detection when changing
options, add more verbose extack errors and check if a vlan should
be used (br_vlan_should_use checks)
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll be dumping the options for the whole range if they're equal. The
first range vlan will be used to extract the options. The commit doesn't
change anything yet it just adds the skeleton for the support. The dump
will happen when the first option is added.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure that br_allowed_egress is called only when we have
BR_STATE_FORWARDING state then we can avoid a test later when we add
per-vlan state.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can notify, send a notification on add/del or change of flags.
Notifications are also compressed when possible to reduce their number
and relieve user-space of extra processing, due to that we have to
manually notify after each add/del in order to avoid double
notifications. We try hard to notify only about the vlans which actually
changed, thus a single command can result in multiple notifications
about disjoint ranges if there were vlans which didn't change inside.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rtnetlink group for bridge vlan notifications - RTNLGRP_BRVLAN
and add support for sending vlan notifications (both single and ranges).
No functional changes intended, the notification support will be used by
later patches.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vlandb nl attribute - BRIDGE_VLANDB_ENTRY_RANGE which causes
RTM_NEWVLAN/DELVAN to act on a range. Dumps now automatically compress
similar vlans into ranges. This will be also used when per-vlan options
are introduced and vlans' options match, they will be put into a single
range which is encapsulated in one netlink attribute. We need to run
similar checks as br_process_vlan_info() does because these ranges will
be used for options setting and they'll be able to skip
br_process_vlan_info().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding RTM_DELVLAN support similar to RTM_NEWVLAN is simple, just need to
map DELVLAN to DELLINK and register the handler.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial RTM_NEWVLAN support which can only create vlans, operating
similar to the current br_afspec(). We will use it later to also change
per-vlan options. Old-style (flag-based) vlan ranges are not allowed
when using RTM messages, we will introduce vlan ranges later via a new
nested attribute which would allow us to have all the information about a
range encapsulated into a single nl attribute.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds vlan rtm definitions:
- NEWVLAN: to be used for creating vlans, setting options and
notifications
- DELVLAN: to be used for deleting vlans
- GETVLAN: used for dumping vlan information
Dumping vlans which can span multiple messages is added now with basic
information (vid and flags). We use nlmsg_parse() to validate the header
length in order to be able to extend the message with filtering
attributes later.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack messages on vlan processing errors. We need to move the flags
missing check after the "last" check since we may have "last" set but
lack a range end flag in the next entry.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to check if a vlan id or range are valid. The range helper
must be called when range start or end are detected.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
