Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull misc vfs updates from Al Viro:
"All kinds of misc stuff, without any unifying topic, from various
people.
Neil's d_anon patch, several bugfixes, introduction of kvmalloc
analogue of kmemdup_user(), extending bitfield.h to deal with
fixed-endians, assorted cleanups all over the place..."
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
alpha: osf_sys.c: use timespec64 where appropriate
alpha: osf_sys.c: fix put_tv32 regression
jffs2: Fix use-after-free bug in jffs2_iget()'s error handling path
dcache: delete unused d_hash_mask
dcache: subtract d_hash_shift from 32 in advance
fs/buffer.c: fold init_buffer() into init_page_buffers()
fs: fold __inode_permission() into inode_permission()
fs: add RWF_APPEND
sctp: use vmemdup_user() rather than badly open-coding memdup_user()
snd_ctl_elem_init_enum_names(): switch to vmemdup_user()
replace_user_tlv(): switch to vmemdup_user()
new primitive: vmemdup_user()
memdup_user(): switch to GFP_USER
eventfd: fold eventfd_ctx_get() into eventfd_ctx_fileget()
eventfd: fold eventfd_ctx_read() into eventfd_read()
eventfd: convert to use anon_inode_getfd()
nfs4file: get rid of pointless include of btrfs.h
uvc_v4l2: clean copyin/copyout up
vme_user: don't use __copy_..._user()
usx2y: don't bother with memdup_user() for 16-byte structure
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 97a6ec4ac0 ("rhashtable: Change rhashtable_walk_start to
return void") only initialized ret for the first time, when going
to again path, the next tsp could be NULL. Without resetting ret,
cb_done would be called with tsp as NULL.
A kernel crash was caused by this when running sctpdiag testcase
in sctp-tests.
Note that this issue doesn't affect net.git yet.
Fixes: 97a6ec4ac0 ("rhashtable: Change rhashtable_walk_start to return void")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate gso_type during segmentation as SKB_GSO_DODGY sources
may pass packets where the gso_type does not match the contents.
Syzkaller was able to enter the SCTP gso handler with a packet of
gso_type SKB_GSO_TCPV4.
On entry of transport layer gso handlers, verify that the gso_type
matches the transport protocol.
Fixes: 90017accff ("sctp: Add GSO support")
Link: http://lkml.kernel.org/r/<001a1137452496ffc305617e5fe0@google.com>
Reported-by: syzbot+fee64147a25aecd48055@syzkaller.appspotmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc has been ignoring struct file_operations::owner field for 10 years.
Specifically, it started with commit 786d7e1612
("Fix rmmod/read/write races in /proc entries"). Notice the chunk where
inode->i_fop is initialized with proxy struct file_operations for
regular files:
- if (de->proc_fops)
- inode->i_fop = de->proc_fops;
+ if (de->proc_fops) {
+ if (S_ISREG(inode->i_mode))
+ inode->i_fop = &proc_reg_file_ops;
+ else
+ inode->i_fop = de->proc_fops;
+ }
VFS stopped pinning module at this point.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check in sctp_sockaddr_af is not robust enough to forbid binding a
v4mapped v6 addr on a v4 socket.
The worse thing is that v4 socket's bind_verify would not convert this
v4mapped v6 addr to a v4 addr. syzbot even reported a crash as the v4
socket bound a v6 addr.
This patch is to fix it by doing the common sa.sa_family check first,
then AF_INET check for v4mapped v6 addrs.
Fixes: 7dab83de50 ("sctp: Support ipv6only AF_INET6 sockets.")
Reported-by: syzbot+7b7b518b1228d2743963@syzkaller.appspotmail.com
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit cea0cc80a6 ("sctp: use the right sk after waking up from
wait_buf sleep"), it may change to lock another sk if the asoc has been
peeled off in sctp_wait_for_sndbuf.
However, the asoc's new sk could be already closed elsewhere, as it's in
the sendmsg context of the old sk that can't avoid the new sk's closing.
If the sk's last one refcnt is held by this asoc, later on after putting
this asoc, the new sk will be freed, while under it's own lock.
This patch is to revert that commit, but fix the old issue by returning
error under the old sk's lock.
Fixes: cea0cc80a6 ("sctp: use the right sk after waking up from wait_buf sleep")
Reported-by: syzbot+ac6ea7baa4432811eb50@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introducing sctp_stream structure, sctp uses stream->outcnt as the
out stream nums instead of c.sinit_num_ostreams.
However when users use sinit in cmsg, it only updates c.sinit_num_ostreams
in sctp_sendmsg. At that moment, stream->outcnt is still using previous
value. If it's value is not updated, the sinit_num_ostreams of sinit could
not really work.
This patch is to fix it by updating stream->outcnt and reiniting stream
if stream outcnt has been change by sinit in sendmsg.
Fixes: a83863174a ("sctp: prepare asoc stream for stream reconf")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fall-through are expected.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sockopt handling functions were calculating the length of the
buffer to be written to userspace and then calculating it again when
actually writing the buffer, which could lead to some write not using
an up-to-date length.
This patch updates such places to just make use of the len variable.
Also, replace some sizeof(type) to sizeof(var).
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu reported that some sockopt calls could cause the kernel to log
a warning on memory allocation failure if the user supplied a large optlen
value. That is because some of them called memdup_user() without a ceiling
on optlen, allowing it to try to allocate really large buffers.
This patch adds a ceiling by limiting optlen to the maximum allowed that
would still make sense for these sockopt.
Reported-by: Hangbin Liu <haliu@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So replace it with GFP_USER and also add __GFP_NOWARN.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a hang involving SCTP, on which it kept flooding dmesg
with the message:
[ 246.742374] sctp: sctp_transport_update_pmtu: Reported pmtu 508 too
low, using default minimum of 512
That happened because whenever SCTP hits an ICMP Frag Needed, it tries
to adjust to the new MTU and triggers an immediate retransmission. But
it didn't consider the fact that MTUs smaller than the SCTP minimum MTU
allowed (512) would not cause the PMTU to change, and issued the
retransmission anyway (thus leading to another ICMP Frag Needed, and so
on).
As IPv4 (ip_rt_min_pmtu=556) and IPv6 (IPV6_MIN_MTU=1280) minimum MTU
are higher than that, sctp_transport_update_pmtu() is changed to
re-fetch the PMTU that got set after our request, and with that, detect
if there was an actual change or not.
The fix, thus, skips the immediate retransmission if the received ICMP
resulted in no change, in the hope that SCTP will select another path.
Note: The value being used for the minimum MTU (512,
SCTP_DEFAULT_MINSEGMENT) is not right and instead it should be (576,
SCTP_MIN_PMTU), but such change belongs to another patch.
Changes from v1:
- do not disable PMTU discovery, in the light of commit
06ad391919 ("[SCTP] Don't disable PMTU discovery when mtu is small")
and as suggested by Xin Long.
- changed the way to break the rtx loop by detecting if the icmp
resulted in a change or not
Changes from v2:
none
See-also: https://lkml.org/lkml/2017/12/22/811
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if PMTU discovery is disabled on a given transport, but the
configured value is higher than the actual PMTU, it is likely that we
will get some icmp Frag Needed. The issue is, if PMTU discovery is
disabled, we won't update the information and will issue a
retransmission immediately, which may very well trigger another ICMP,
and another retransmission, leading to a loop.
The fix is to simply not trigger immediate retransmissions if PMTU
discovery is disabled on the given transport.
Changes from v2:
- updated stale comment, noticed by Xin Long
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot noticed a NULL pointer dereference panic in sctp_stream_free()
which was caused by an incomplete error handling in sctp_stream_init().
By not clearing stream->outcnt, it made a for() in sctp_stream_free()
think that it had elements to free, but not, leading to the panic.
As suggested by Xin Long, this patch also simplifies the error path by
moving it to the only if() that uses it.
See-also: https://www.spinics.net/lists/netdev/msg473756.html
See-also: https://www.spinics.net/lists/netdev/msg465024.html
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: f952be79ce ("sctp: introduce struct sctp_stream_out_ext")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove SCTP probe module since jprobe has been deprecated.
That function is now replaced by sctp/sctp_probe and
sctp/sctp_probe_path trace-events.
You can use it via ftrace or perftools.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SCTP ACK tracking trace event to trace the changes of SCTP
association state in response to incoming packets.
It is used for debugging SCTP congestion control algorithms,
and will replace sctp_probe module.
Note that this event a bit tricky. Since this consists of 2
events (sctp_probe and sctp_probe_path) so you have to enable
both events as below.
# cd /sys/kernel/debug/tracing
# echo 1 > events/sctp/sctp_probe/enable
# echo 1 > events/sctp/sctp_probe_path/enable
Or, you can enable all the events under sctp.
# echo 1 > events/sctp/enable
Since sctp_probe_path event is always invoked from sctp_probe
event, you can not see any output if you only enable
sctp_probe_path.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch(180d8cd942) replaces all uses of struct sock fields'
memory_pressure, memory_allocated, sockets_allocated, and sysctl_mem
to accessor macros. But the sockets_allocated field of sctp sock is
not replaced at all. Then replace it now for unifying the code.
Fixes: 180d8cd942 ("foundations of per-cgroup memory pressure controlling.")
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With changes in inet_ files, SCTP state transitions are traced with
inet_sock_set_state tracepoint.
As SCTP state names, i.e. SCTP_SS_CLOSED, SCTP_SS_ESTABLISHED,
have the same value with TCP state names. So the output info still print
the TCP state names, that makes the code easy.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a new type of chunk is added, the corresp conversion in
sctp_cname should be added. Otherwise, in some places, pr_debug
will print it as "unknown chunk".
Fixes: cc16f00f65 ("sctp: add support for generating stream reconf ssn reset request chunk")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when reneging events in sctp_ulpq_renege(), the variable freed
could be increased by a __u16 value twice while freed is of __u16
type. It means freed may overflow at the second addition.
This patch is to fix it by using __u32 type for 'freed', while at
it, also to remove 'if (chunk)' check, as all renege commands are
generated in sctp_eat_data and it can't be NULL.
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last patch for support of stream interleave, after this patch,
users could enable stream interleave by systcl -w net.sctp.intl_enable=1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using idata and doing stream and asoc reset, setting ssn with
0 could only clear the 1st 16 bits of mid.
So to make this work for both data and idata, it sets mid with 0
instead of ssn, and also mid_uo for unordered idata also need to
be cleared, as said in section 2.3.2 of RFC8260.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Marcelo said in the stream scheduler patch:
Support for I-DATA chunks, also described in RFC8260, with user message
interleaving is straightforward as it just requires the schedulers to
probe for the feature and ignore datamsg boundaries when dequeueing.
All needs to do is just to ignore datamsg boundaries when dequeueing.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
handle_ftsn is added as a member of sctp_stream_interleave, used to skip
ssn for data or mid for idata, called for SCTP_CMD_PROCESS_FWDTSN cmd.
sctp_handle_iftsn works for ifwdtsn, and sctp_handle_fwdtsn works for
fwdtsn. Note that different from sctp_handle_fwdtsn, sctp_handle_iftsn
could do stream abort pd.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
report_ftsn is added as a member of sctp_stream_interleave, used to
skip tsn from tsnmap, remove old events from reasm or lobby queue,
and abort pd for data or idata, called for SCTP_CMD_REPORT_FWDTSN
cmd and asoc reset.
sctp_report_iftsn works for ifwdtsn, and sctp_report_fwdtsn works
for fwdtsn. Note that sctp_report_iftsn doesn't do asoc abort_pd,
as stream abort_pd will be done when handling ifwdtsn. But when
ftsn is equal with ftsn, which means asoc reset, asoc abort_pd has
to be done.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
validate_ftsn is added as a member of sctp_stream_interleave, used to
validate ssn/chunk type for fwdtsn or mid (message id)/chunk type for
ifwdtsn, called in sctp_sf_eat_fwd_tsn, just as validate_data.
If this check fails, an abort packet will be sent, as said in section
2.3.1 of RFC8260.
As ifwdtsn and fwdtsn chunks have different length, it also defines
ftsn_chunk_len for sctp_stream_interleave to describe the chunk size.
Then it replaces all sizeof(struct sctp_fwdtsn_chunk) with
sctp_ftsnchk_len.
It also adds the process for ifwdtsn in rx path. As Marcelo pointed
out, there's no need to add event table for ifwdtsn, but just share
prsctp_chunk_event_table with fwdtsn's. It would drop fwdtsn chunk
for ifwdtsn and drop ifwdtsn chunk for fwdtsn by calling validate_ftsn
in sctp_sf_eat_fwd_tsn.
After this patch, the ifwdtsn can be accepted.
Note that this patch also removes the sctp.intl_enable check for
idata chunks in sctp_chunk_event_lookup, as it will do this check
in validate_data later.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
generate_ftsn is added as a member of sctp_stream_interleave, used to
create fwdtsn or ifwdtsn chunk according to abandoned chunks, called
in sctp_retransmit and sctp_outq_sack.
sctp_generate_iftsn works for ifwdtsn, and sctp_generate_fwdtsn is
still used for making fwdtsn.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_ifwdtsn_skip, sctp_ifwdtsn_hdr and sctp_ifwdtsn_chunk are used to
define and parse I-FWD TSN chunk format, and sctp_make_ifwdtsn is a
function to build the chunk.
The I-FORWARD-TSN Chunk Format is defined in section 2.3.1 of RFC8260.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo R. Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_setsockopt_reset_streams, it only does the check
optlen < sizeof(*params) for optlen. But it's not enough, as
params->srs_number_streams should also match optlen.
If the streams in params->srs_stream_list are less than stream
nums in params->srs_number_streams, later when dereferencing
the stream list, it could cause a slab-out-of-bounds crash, as
reported by syzbot.
This patch is to fix it by also checking the stream numbers in
sctp_setsockopt_reset_streams to make sure at least it's not
greater than the streams in the list.
Fixes: 7f9d68ac94 ("sctp: implement sender-side procedures for SSN Reset Request Parameter")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unordered idata process is more complicated than unordered data:
- It has to add mid into sctp_stream_out to save the next mid value,
which is separated from ordered idata's.
- To support pd for unordered idata, another mid and pd_mode need to
be added to save the message id and pd state in sctp_stream_in.
- To make unordered idata reasm easier, it adds a new event queue
to save frags for idata.
The patch mostly adds the samilar reasm functions for unordered idata
as ordered idata's, and also adjusts some other codes on assign_mid,
abort_pd and ulpevent_data for idata.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
abort_pd is added as a member of sctp_stream_interleave, used to abort
partial delivery for data or idata, called in sctp_cmd_assoc_failed.
Since stream interleave allows to do partial delivery for each stream
at the same time, sctp_intl_abort_pd for idata would be very different
from the old function sctp_ulpq_abort_pd for data.
Note that sctp_ulpevent_make_pdapi will support per stream in this
patch by adding pdapi_stream and pdapi_seq in sctp_pdapi_event, as
described in section 6.1.7 of RFC6458.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
start_pd is added as a member of sctp_stream_interleave, used to
do partial_delivery for data or idata when datalen >= asoc->rwnd
in sctp_eat_data. The codes have been done in last patches, but
they need to be extracted into start_pd, so that it could be used
for SCTP_CMD_PART_DELIVER cmd as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
renege_events is added as a member of sctp_stream_interleave, used to
renege some old data or idata in reasm or lobby queue properly to free
some memory for the new data when there's memory stress.
It defines sctp_renege_events for idata, and leaves sctp_ulpq_renege
as it is for data.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enqueue_event is added as a member of sctp_stream_interleave, used to
enqueue either data, idata or notification events into user socket rx
queue.
It replaces sctp_ulpq_tail_event used in the other places with
enqueue_event.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ulpevent_data is added as a member of sctp_stream_interleave, used to
do the most process in ulpq, including to convert data or idata chunk
to event, reasm them in reasm queue and put them in lobby queue in
right order, and deliver them up to user sk rx queue.
This procedure is described in section 2.2.3 of RFC8260.
It adds most functions for idata here to do the similar process as
the old functions for data. But since the details are very different
between them, the old functions can not be reused for idata.
event->ssn and event->ppid settings are moved to ulpevent_data from
sctp_ulpevent_make_rcvmsg, so that sctp_ulpevent_make_rcvmsg could
work for both data and idata.
Note that mid is added in sctp_ulpevent for idata, __packed has to
be used for defining sctp_ulpevent, or it would exceeds the skb cb
that saves a sctp_ulpevent variable for ulp layer process.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
validate_data is added as a member of sctp_stream_interleave, used
to validate ssn/chunk type for data or mid (message id)/chunk type
for idata, called in sctp_eat_data.
If this check fails, an abort packet will be sent, as said in
section 2.2.3 of RFC8260.
It also adds the process for idata in rx path. As Marcelo pointed
out, there's no need to add event table for idata, but just share
chunk_event_table with data's. It would drop data chunk for idata
and drop idata chunk for data by calling validate_data in
sctp_eat_data.
As last patch did, it also replaces sizeof(struct sctp_data_chunk)
with sctp_datachk_len for rx path.
After this patch, the idata can be accepted and delivered to ulp
layer.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
assign_number is added as a member of sctp_stream_interleave, used
to assign ssn for data or mid (message id) for idata, called in
sctp_packet_append_data. sctp_chunk_assign_ssn is left as it is,
and sctp_chunk_assign_mid is added for sctp_stream_interleave_1.
This procedure is described in section 2.2.2 of RFC8260.
All sizeof(struct sctp_data_chunk) in tx path is replaced with
sctp_datachk_len, to make it right for idata as well. And also
adjust sctp_chunk_is_data for SCTP_CID_I_DATA.
After this patch, idata can be built and sent in tx path.
Note that if sp strm_interleave is set, it has to wait_connect in
sctp_sendmsg, as asoc intl_enable need to be known after 4 shake-
hands, to decide if it should use data or idata later. data and
idata can't be mixed to send in one asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid hundreds of checks for the different process on I-DATA chunk,
struct sctp_stream_interleave is defined as a group of functions used
to replace the codes in some place where it needs to do different job
according to if the asoc intl_enabled is set.
With these ops, it only needs to initialize asoc->stream.si with
sctp_stream_interleave_0 for normal data if asoc intl_enable is 0,
or sctp_stream_interleave_1 for idata if asoc intl_enable is set in
sctp_stream_init.
After that, the members in asoc->stream.si can be used directly in
some special places without checking asoc intl_enable.
make_datafrag is the first member for sctp_stream_interleave, it's
used to make data or idata frags, called in sctp_datamsg_from_user.
The old function sctp_make_datafrag_empty needs to be adjust some
to fit in this ops.
Note that as idata and data chunks have different length, it also
defines data_chunk_len for sctp_stream_interleave to describe the
chunk size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_idatahdr and sctp_idata_chunk are used to define and parse
I-DATA chunk format, and sctp_make_idata is a function to build
the chunk.
The I-DATA Chunk Format is defined in section 2.1 of RFC8260.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
