Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The wrong bit was masked when acking langwell gpio interrupts.
Reason for maskig the wrong bit was probably because__ffs() and ffs() functions
return bit indexes differently (0..31 vs 1..32)
This fixes langwell based devices from hanging when a gpio interrupt is
triggered and undoes the breakage which occurred in change set
732063b92b
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If gpio pins from bank[2-5] are marked as wakeup enable and if the wake is
through gpio IO pad wakeup, then that wakeup gpio interrupt is lost.
In the current implementation, GPIO driver stores the context of DATAIN of
all the gpio in the bank. During GPIO resuming, it checks DATAIN with wakeup
enabled pins of gpio bank. If there is status change, then manually toggle
GPIO_LEVELDETECT to generate pseudo interrupt.
Reported-by: Philippe Mazet <p-mazet@ti.com>
Tested-by: Philippe Mazet <p-mazet@ti.com>
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
_set_gpio_triggering uses read-modify-write on bank registers,
lock bank->lock around all calls to it to prevent register
corruption if two cpus access gpios in the same bank at the
same time.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setting the IRQWAKEN bit was overwriting previous IRQWAKEN bits,
causing only the last bit set to take effect, resulting in lost
wakeups when the GPIO controller is in idle.
Replace direct writes to IRQWAKEN with MOD_REG_BIT calls to
perform a read-modify-write on the register.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
WARNING: arch/arm/plat-omap/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function omap_gpio_probe() to the function .init.text:omap_gpio_chip_init()
The function __devinit omap_gpio_probe() references
a function __init omap_gpio_chip_init().
If omap_gpio_chip_init is only used by omap_gpio_probe then
annotate omap_gpio_chip_init with a matching annotation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
After the GPIO driver move, some symbols became selectable when they
shouldn't be. Tighten the dependencies.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We had a few drivers move from arch/arm into drivers/gpio, but they
don't actually compile without the ARM platform headers etc. As a
result they were messing up allyesconfig on x86.
Make them depend on ARM.
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/pch_gpio: Support new device ML7223
gpio: make gpio_{request,free}_array gpio array parameter const
GPIO: OMAP: move to drivers/gpio
GPIO: OMAP: move register offset defines into <plat/gpio.h>
gpio: Convert gpio_is_valid to return bool
gpio: Move the s5pc100 GPIO to drivers/gpio
gpio: Move the s5pv210 GPIO to drivers/gpio
gpio: Move the exynos4 GPIO to drivers/gpio
gpio: Move to Samsung common GPIO library to drivers/gpio
gpio/nomadik: add function to read GPIO pull down status
gpio/nomadik: show all pins in debug
gpio: move Nomadik GPIO driver to drivers/gpio
gpio: move U300 GPIO driver to drivers/gpio
langwell_gpio: add runtime pm support
gpio/pca953x: Add support for pca9574 and pca9575 devices
gpio/cs5535: Show explicit dependency between gpio_cs5535 and mfd_cs5535
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO 1 to 8 are added for TPS65911 chip version. The gpio driver
now handles more than one gpio lines. Subsequent versions of the
chip family can add new GPIO lines with minimal driver changes.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The GPIO driver should reside in drivers/gpio/ for better
organization.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Move the Samsung s5pc100 SoC GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move the Samsung s5pv210 SoC GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move the Samsung Exynos4 series SoCs GPIO driver to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
It's common gpiolib for recent Samsung SoCs. Move to drivers/gpio
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Useful to check the status of the runtime pin muxing.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Squashed, modified to use chip-internal IRQ trigger state]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This moves the Nomadik GPIO driver out of arch/arm/plat-nomadik
and into the desired location indicated by the subsystem
maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[grant.likely: squashed with kconfig fixup]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This moves the U300 GPIO driver out of arch/arm/mach-u300 and into
the desired location indicated by the subsystem maintainer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While this is essentially a no-op for this driver, it has the
side effect of letting the PMU driver snoop D3 requests from
the PCI core for this driver.
This is only for langwell, not for whitney point.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
PCA957x is i2c gpio expander, and similar to PCA953x. Although register
configurations are different between PCA957x and PCA953x. They can share
a lot of components, such as IRQ handling, GPIO IN/OUT. So updating PCA953x
driver to support PCA957x chips.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
cs5535-gpio.c has been split into two, with various setup moved
into cs5535-mfd.c. Given that cs5535-gpio will not load without
the -mfd part, lets make that dependency explicit in Kconfig
Signed-off-by: Ed Wildgoose <kernel@wildgooses.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/via: rename VIA local config struct
basic_mmio_gpio: split into a gpio library and platform device
gpio: remove some legacy comments in build files
gpio: add trace events for setting direction and value
gpio/pca953x: Use handle_simple_irq instead of handle_edge_irq
gpiolib: export gpiochip_find
gpio: remove redundant Kconfig depends on GPIOLIB
basic_mmio_gpio: convert to non-__raw* accessors
basic_mmio_gpio: support direction registers
basic_mmio_gpio: support different input/output registers
basic_mmio_gpio: detect output method at probe time
basic_mmio_gpio: request register regions
basic_mmio_gpio: allow overriding number of gpio
basic_mmio_gpio: convert to platform_{get,set}_drvdata()
basic_mmio_gpio: remove runtime width/endianness evaluation
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
alpha allmodconfig:
drivers/gpio/ml_ioh_gpio.c: In function 'ioh_gpio_probe':
drivers/gpio/ml_ioh_gpio.c:205: error: implicit declaration of function 'kzalloc'
drivers/gpio/ml_ioh_gpio.c:205: warning: assignment makes pointer from integer without a cast
also fix this:
drivers/gpio/ml_ioh_gpio.c:145: warning: 'ioh_gpio_save_reg_conf' defined but not used
drivers/gpio/ml_ioh_gpio.c:154: warning: 'ioh_gpio_restore_reg_conf' defined but not used
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha allmodconfig:
drivers/gpio/vx855_gpio.c: In function 'vx855gpio_probe':
drivers/gpio/vx855_gpio.c:233: error: implicit declaration of function 'kzalloc'
drivers/gpio/vx855_gpio.c:233: warning: assignment makes pointer from integer without a cast
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow GPIO_BASIC_MMIO_CORE to be used to provide an accessor library
for implementing GPIO drivers whilst abstracting the register access
detail. Based on a patch from Anton Vorontsov[1] and adapted to allow
bgpio_chip to be embedded in another structure.
Changes since v1:
- Register the gpio_chip in the platform device probe
1. https://lkml.org/lkml/2011/4/19/401
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The build files for drivers/gpio has some wording and comments
about the directory being reserved exclusively for GPIO expanders
(according to the gpio.txt file these are on external busses) and
this has been false for some time. We already have PL061 and
Xilinx drivers which are in silicon and now I'm moving more
silicon drivers here, so delete this and reword it a bit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch allows to trace gpio operations using ftrace
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make pca953x driver use the simple irq handler since no hardware control
is necessary and the driver lacks an irq_ack function. handle_edge_irq()
calls chip->irq_ack() which crashes since this function does not exist.
Signed-off-by: Erik Botö <erik.boto@pelagicore.com>
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Export function gpiochip_find so that modules can use it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since all the drivers are in a 'if GPIOLIB/endif block', the depends on GPIOLIB
is redundant so remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The __raw_* accessors don't include memory barriers and can cause
problems when writes get stuck in write buffers.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Most controllers require the direction of a GPIO to be set by writing to
a direction register. Add support for either an input direction
register or an output direction register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some controllers have separate input and output registers. For these
controllers, use "set" for the output and "dat" for the input.
Changes since v2: reuse "set" for output and "dat" for input rather than
adding a new "in" register.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Rather than detecting the output method each time in the .set()
callback, do it at probe time and set the appropriate callback.
Changes since v2: moved the reg_dat initialization into
bgpio_setup_io().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make sure that we get the register regions with request_mem_region()
before ioremap() to make sure we have exclusive access.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some platforms may have a number of GPIO that is less than the register
width of the peripheral.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the platform drvdata helpers rather than working on the struct
device itself.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
