The Apex Embedded Systems STX104 is a 16-channel 16-bit analog input and
2-channel 16-bit analog output PC/104 card. The STX104 incorporates a
large one mega-sample FIFO.
This driver provides IIO support for the 2-channel DAC on the STX104.
The base port addresses for the devices may be configured via the "base"
module parameter array.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The only difference between the MPU6000 and the
MPU6050 is that the first also supports SPI.
Add SPI driver for this chip.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Separate this driver into core and i2c functionality.
This is in preparation for adding spi support.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use regmap instead of i2c specific functions.
This is in preparation of splitting this driver into core and
i2c specific functionality.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Acked-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The select/deselect_bypass duo writes the irq number into the interrupt
configuration register.
If there is a i2c slave device connected to the mpu (eg. a magnetometer)
then this can hinder interrupt delivery for the accelerometer and
gyroscope.
Set this register to the default configuration.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds ADC0831/ADC0832/ADC0834/ADC0838 8-bit ADC driver.
I have tested with ADC0831 and ADC0832. The remaining ADC0834 and
ADC0838 are very similar to ADC0832.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The DMAengine framework gained support for synchronized transfer
termination. Use the new dmaengine_terminate_sync() function instead of
dmaengine_terminate_all(), this avoids a potential race condition when
disabling the buffer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The AD5625/AD5645/AD5665 are a family of 4 channel DACs with 12-bit, 14-bit
and 16-bit precision respectively. The devices come in 3 flavors in terms
of built-in reference, either no built-in reference, built-in 1.25V
reference or built-in 2.5V reference.
The AD5627/AD5647/AD5667 are similar to the AD5625/AD5645/AD5665 except
that they have 2 instead of 4 channels.
While these new devices are mostly register map compatible with the
existing devices support by the driver some offsets and register addresses
have been shuffled around. To accommodate this introduce a new register map
layout. For the lack of a better name we will just call it version 2.
Datasheets:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5625R_5645R_5665R_5625_5665.pdfhttp://www.analog.com/media/en/technical-documentation/data-sheets/AD5627R_5647R_5667R_5627_5667.pdf
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the ad5064 only supports two different register map variations
and this is represented by a bool. This patch changes since to a enum so
we can support more variations in the future.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
List the newly support LTC devices in the Kconfig entry for the AD5064
driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Linear Technology LTC2606, LTC2607, LTC2609, LTC2616, LTC2617,
LTC2619, LTC2626, LTC2627 and LTC2629 devices are very similar
to the AD5064 device.
This patch adds support for those devices.
Datasheet for LTC devices:
LTC2606, LTC2616, LTC2626: http://www.linear.com/docs/6398
LTC2607, LTC2617, LTC2627: http://www.linear.com/docs/8977
LTC2709, LTC2619, LTC2629: http://www.linear.com/docs/8477
Signed-off-by: Marc Andre <marc.andre@netline.ch>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch makes minor structural changes to support specifics
for LTC2617 DAC. This DAC requires different handling of the
power down modes. The configuration to actually support the
DAC will be submitted in a secondary patch.
Adjust the DECLARE_AD5064_CHANNELS() macro to accept a new
ext_info parameter. This allows to use different power down
modes per DAC. (e.g. DAC only support 90kohm to ground)
Add the chip_info parameter "powerdown_ltc". This parameter is
used in the ad5064_sync_powerdown_mode() function to handle the
power down command for LTC diffently. For those devices the
power down command must be addressed to the channel.
Signed-off-by: Marc Andre <marc.andre@netline.ch>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add driver for the TI AFE4403 heart rate monitor and pulse oximeter.
This device detects reflected LED light fluctuations and presents an ADC
value to the user space for further signal processing.
Data sheet located here:
http://www.ti.com/product/AFE4403/datasheet
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add driver for the TI AFE4404 heart rate monitor and pulse oximeter.
This device detects reflected LED light fluctuations and presents an ADC
value to the user space for further signal processing.
Datasheet: http://www.ti.com/product/AFE4404/datasheet
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The newly added atlas-ph-sensor driver uses irq_work_queue, which
may not always be enabled:
ERROR: "irq_work_queue" [drivers/iio/chemical/atlas-ph-sensor.ko] undefined!
This adds a 'select' statement to Kconfig to ensure it's there
when we need it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 27dec00ecf ("iio: chemical: add Atlas pH-SM sensor support")
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have the same code for computing the scan index storage size in bytes
all over the place. Factor this out into helper functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This will be used together with an external trigger (e.g hrtimer
based software trigger).
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This allows data exported via buffer interface to be converted
to standard units in userspace.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Device Support
* ad5761
- new driver
* at91_sama5d2 ADC.
- new driver and MAINTAINERS entry.
- minor cleanups followed.
* atlas pH-SM
- new driver (this has possibly the prettiest data sheet I've ever seen)
* mcp3422
- mcp3425 ADC added.
* mcp4725
- mcp4726 DAC added.
* mma8452
- mma8451q accelerometer added.
* mpl115
- mpl115a1 added (a lot bigger than it seems as this is an SPI part whereas
previous parts were i2c).
* si7005
- Hoperf th02 (seems to be a repackaged part)
* si7020
- Hoperf th06 (seems to be a repackaged part)
New features
* Core
- IIO_PH type. Does what it says on the tin.
* max30100
- LED current configuration support.
* mcp320x
- more differential measurement combinations.
* mma8452
- free fall deteciton
- opt3001
- enable operation without a IRQ line.
- device tree docs. Somehow the original docs have disappeared down
a rabbit hole, so here is a new set.
* st-sensors
- Support active-low interrupts.
Cleanups and minor / not so minor reworks
* Documentation
- drop some defunct ABI from the docs in staging.
* presure / Kconfig
- white space cleanup.
* ad7150
- BIT macro usage
- Alignment fixes
* ad7192
- false indent fixed.
* ak8975
- constify the ak_def structures
* axp288
- drop a redundant double const.
* dht11
- substantial reliability improvements by being more tolerant
of missing start bits.
- simplify the decoding algorithm
* mma8452
- whitespace cleanup
* mpl115
- don't bother setting i2c_client_data as nothing uses it.
* mpu6050
- drop unused function parameter.
* opt3001
- extract integration time as constants.
- trivial refactoring.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=fgTH
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new IIO device support, features and cleanups for the 4.6 cycle.
Device Support
* ad5761
- new driver
* at91_sama5d2 ADC.
- new driver and MAINTAINERS entry.
- minor cleanups followed.
* atlas pH-SM
- new driver (this has possibly the prettiest data sheet I've ever seen)
* mcp3422
- mcp3425 ADC added.
* mcp4725
- mcp4726 DAC added.
* mma8452
- mma8451q accelerometer added.
* mpl115
- mpl115a1 added (a lot bigger than it seems as this is an SPI part whereas
previous parts were i2c).
* si7005
- Hoperf th02 (seems to be a repackaged part)
* si7020
- Hoperf th06 (seems to be a repackaged part)
New features
* Core
- IIO_PH type. Does what it says on the tin.
* max30100
- LED current configuration support.
* mcp320x
- more differential measurement combinations.
* mma8452
- free fall deteciton
- opt3001
- enable operation without a IRQ line.
- device tree docs. Somehow the original docs have disappeared down
a rabbit hole, so here is a new set.
* st-sensors
- Support active-low interrupts.
Cleanups and minor / not so minor reworks
* Documentation
- drop some defunct ABI from the docs in staging.
* presure / Kconfig
- white space cleanup.
* ad7150
- BIT macro usage
- Alignment fixes
* ad7192
- false indent fixed.
* ak8975
- constify the ak_def structures
* axp288
- drop a redundant double const.
* dht11
- substantial reliability improvements by being more tolerant
of missing start bits.
- simplify the decoding algorithm
* mma8452
- whitespace cleanup
* mpl115
- don't bother setting i2c_client_data as nothing uses it.
* mpu6050
- drop unused function parameter.
* opt3001
- extract integration time as constants.
- trivial refactoring.
Here are some small staging driver fixes for 4.5-rc2. One of them
predated 4.4-final, but I missed that merge window due to the holliday.
The others fix reported issues that have come up recently. The tty
change is needed for the speakup driver fix and has the ack of the tty
driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlauWLoACgkQMUfUDdst+ynHbQCfWlGgQhtadfhtiaIKLwqy9NPG
PksAn3/z4mXX037sfm2kZrcqtcNlv9zf
=Vdai
-----END PGP SIGNATURE-----
Merge tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 4.5-rc2.
One of them predated 4.4-final, but I missed that merge window due to
the holliday. The others fix reported issues that have come up
recently. The tty change is needed for the speakup driver fix and has
the ack of the tty driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues"
* tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: speakup: fix read scrolled-back VT
Staging: speakup: Fix getting port information
Revert "Staging: panel: usleep_range is preferred over udelay"
iio: adis_buffer: Fix out-of-bounds memory access
The inv_check_and_setup_chip function does not use the i2c_device_id
parameter. Therefore remove it.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the Atlas Scientific pH-SM chemical sensor that can
detect pH levels of solutions in the range of 0-14.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for Hoperf th06 humidity and
temperature sensor as it uses same register definitions
as si7020
th06 Datasheet: http://www.hoperf.com/upload/sensor/TH06.pdf
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for Hoperf th02 humidity and
temperature sensor as it uses same register definitions
as si7005
th02 Datasheet: http://www.anglia-live.com/netalogue/pdfs/hrf/datasheets/TH02_V1.1.pdf
Signed-off-by: Cristina Moraru <cristina.moraru09@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Clearly a high degree of cut and paste has gone on in this file, propogating
a particularly random combination of tabs and spaces. This patch at least
should make it all consistent going forward.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The new algorithm uses a 'one size fits em all' threshold, which should
be easier to understand and debug. I believe there are no regressions
compared to the old adaptive threshold algorithm. I don't remember why
I chose the old algorithm when I initially wrote the driver.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Instead of guessing where the data starts, we now just try to decode from
every possible start position. This causes no additional overhead if we
properly received the full preamble and only costs a few extra CPU cycles
in the case where the preamble is corrupted. This is much more efficient
than to return an error to userspace and start over again.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mpl115 driver currently supports i2c interface (MPL115A2).
There is also SPI version (MPL115A1). The difference between them
is only physical transport so we can easily support both while sharing
most of the code.
Split the driver into a core support module and one module each for I2C
and SPI support.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mpl115 sets i2c clientdata, but it is not used anywhere. So remove it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable operation of the TI OPT3001 light sensor without having an
interrupt line available to connect the INT pin to.
In this operation mode, we issue a conversion request and simply wait
for the conversion time available as timeout value, determined from
integration time configuration and the worst-case time given in the data
sheet (sect. 6.5, table on p. 5):
short integration time (100ms): 110ms + 3ms = 113ms
long integration time (800ms): 880ms + 3ms = 883ms
This change is transparent as behaviour defaults to using the interrupt
method if an interrupt no. is configured via device tree. Interrupt-less
operation mode is performed when no valid interrupt no. is given.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Signed-off-by: Michael Hornung <mhornung.linux@gmail.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Change variable type of struct opt3001 members 'ok_to_ignore_lock' and
'result_ready' uint16-bitfield of length one to bool.
They are used as bool, let the compiler do the optimization.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Signed-off-by: Michael Hornung <mhornung.linux@gmail.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Extract integration times as #define constants. This prepares using them
for delay/timeout length determination.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Signed-off-by: Michael Hornung <mhornung.linux@gmail.com>
Tested-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
ad5761 is a 1-channel DAC with configurable output range.
The driver uses the regulator interface for its voltage ref.
It shares its register layout with ad5761r, ad5721 and ad5721r.
Differences:
ad5761* are 16 bit, ad5721* are 12 bits.
ad57*1r have an internal reference.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
duplicate const can be removed, it is redundant. Found by static
analysis using smatch.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for this series' 14 bit accelerometer chip, MMA8451Q.
It's datasheet is available at the vendor's website:
https://cache.freescale.com/files/sensors/doc/data_sheet/MMA8451Q.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds freefall event detection to the supported devices. It adds
the in_accel_x&y&z_mag_falling_en iio event attribute, which activates
freefall mode.
In freefall mode, the current acceleration magnitude (AND combination
of all axis values) is compared to the specified threshold.
If it falls under the threshold (in_accel_mag_falling_value),
the appropriate IIO event code is generated.
This is what the sysfs "events" directory for these devices looks
like after this change:
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_falling_period
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_falling_value
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_rising_period
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_rising_value
-r--r--r-- 4096 Oct 23 08:45 in_accel_scale
-rw-r--r-- 4096 Oct 23 08:45 in_accel_x&y&z_mag_falling_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_x_mag_rising_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_y_mag_rising_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_z_mag_rising_en
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use var type for sizeof argument instead of the struct name.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
vref_uv has to be an int.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Merge third patch-bomb from Andrew Morton:
"I'm pretty much done for -rc1 now:
- the rest of MM, basically
- lib/ updates
- checkpatch, epoll, hfs, fatfs, ptrace, coredump, exit
- cpu_mask simplifications
- kexec, rapidio, MAINTAINERS etc, etc.
- more dma-mapping cleanups/simplifications from hch"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (109 commits)
MAINTAINERS: add/fix git URLs for various subsystems
mm: memcontrol: add "sock" to cgroup2 memory.stat
mm: memcontrol: basic memory statistics in cgroup2 memory controller
mm: memcontrol: do not uncharge old page in page cache replacement
Documentation: cgroup: add memory.swap.{current,max} description
mm: free swap cache aggressively if memcg swap is full
mm: vmscan: do not scan anon pages if memcg swap limit is hit
swap.h: move memcg related stuff to the end of the file
mm: memcontrol: replace mem_cgroup_lruvec_online with mem_cgroup_online
mm: vmscan: pass memcg to get_scan_count()
mm: memcontrol: charge swap to cgroup2
mm: memcontrol: clean up alloc, online, offline, free functions
mm: memcontrol: flatten struct cg_proto
mm: memcontrol: rein in the CONFIG space madness
net: drop tcp_memcontrol.c
mm: memcontrol: introduce CONFIG_MEMCG_LEGACY_KMEM
mm: memcontrol: allow to disable kmem accounting for cgroup2
mm: memcontrol: account "kmem" consumers in cgroup2 memory controller
mm: memcontrol: move kmem accounting code to CONFIG_MEMCG
mm: memcontrol: separate kmem code from legacy tcp accounting code
...
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Rewrite abs() so that its return type does not depend on the
architecture and no unexpected type conversion happen inside of it. The
only conversion is from unsigned to signed type. char is left as a
return type but treated as a signed type regradless of it's actual
signedness.
With the old version, int arguments were promoted to long and depending
on architecture a long argument might result in s64 or long return type
(which may or may not be the same).
This came after some back and forth with Nicolas. The current macro has
different return type (for the same input type) depending on
architecture which might be midly iritating.
An alternative version would promote to int like so:
#define abs(x) __abs_choose_expr(x, long long, \
__abs_choose_expr(x, long, \
__builtin_choose_expr( \
sizeof(x) <= sizeof(int), \
({ int __x = (x); __x<0?-__x:__x; }), \
((void)0))))
I have no preference but imagine Linus might. :] Nicolas argument against
is that promoting to int causes iconsistent behaviour:
int main(void) {
unsigned short a = 0, b = 1, c = a - b;
unsigned short d = abs(a - b);
unsigned short e = abs(c);
printf("%u %u\n", d, e); // prints: 1 65535
}
Then again, no sane person expects consistent behaviour from C integer
arithmetic. ;)
Note:
__builtin_types_compatible_p(unsigned char, char) is always false, and
__builtin_types_compatible_p(signed char, char) is also always false.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mcp320x driver supports the pseudo-differential mode by
in_voltage'IN+'-voltage'IN-'_raw where (IN+, IN-) = (0, 1), (2, 3), ...
mcp320x chips except MCP3X01 can also select swapped IN+ and IN-
pairs in the pseudo-differential mode.
i.e. in_voltage'IN+'-voltage'IN-'_raw where (IN+, IN-) = (1, 0),
(3, 2), ...
If the voltage level of IN+ is equal to or less than IN-, the
resultant code will be 000h. So it is useful to provide these, too.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Oskar Andero <oskar.andero@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver supports the new version of the Atmel ADC device introduced
with the SAMA5D2 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ak_def structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
