After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is new Intel SoC, so add codec entry for HDMI
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake is next gen SoC, so add the IDs for Geminilake.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake reference platform also uses combo jack for audio connector
so we need to set codec pdata to use this based on DMI match for this
board.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake has two different devices connected to the same SSP, so use
device_type check to get correct device configuration.
Signed-off-by: Senthilnathan Veppur <senthilnathanx.veppur@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the pcm jack is created, create and initialize the pin switch
widget for each port. Pin switch is to enable/disable the pin when
monitor is connected/disconnected.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Represent each port as machine DAPM pin widget. This helps in
enable/disable pin when monitor is connected/disconnected in case pcm
is rendered to multiple ports.
Create machine pin widgets and pin switch kcontrol for each port and
report based on the pin status
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in bxt_da7219_max98357 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in bxt_rt298.c machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in skl_nau88l25_ssm4567 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI PCM and calls hdmi codec API to initialize
jack in skl_nau88l25_max98357a machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Creates ASoC jack for HDMI pcm and calls hdmi codec API to initialize
jack in skl_rt268 machine
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_jack instead of snd_jack and create the jack in machine
driver and pass the jack pointer to hdac_hdmi driver for jack
reporting.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have the MST feature enabled and Pin-Port mux for user to
select the converter routing, multiple port mapping to same converter
needs to be supported.
To support multiple port mapped to same converter following changes are
done for this:.
o Add port list to pcm, so that multiple ports can be mapped to a PCM.
o Jack reporting in case where multiple port are attached to same PCM.
o Change hdac_hdmi_get_port_from_cvt(), channel_map, remove functions
to parse through all ports mapped to same the PCM.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable stream on a specific port of a MST capable pin, the port
needs to be selected before we configure the pin widget verb.
When port is selected, all the pin widget verb controlling the sink
device operation will be directed to selected port. So add port
selection before configuring the pin widget verb.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ELD notification can be received asynchronously from the graphics
side and this may happen just at the moment the sound driver is
initializing and notification will be missed. Similarly at system
resume, the notification is ignored as the ELD and connection states
are updated in anyway at the end of the resume.
So check the jack status in boot/resume by querying the port presence
based on pin caps and report the jack status.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support DP MST audio, new pin verbs/params are added. This patch
adds helper functions to do following:
o To set a specific port
o To get the currently selected port
o To get the length of port.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FSL SAI can support up to 32 channels using TDM. Report that value so
they can actually be used.
Tested using 8 channels.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While unregistering the hdmi-codec, the hdmi device list must be
cleaned up. It avoid kernel page fault when registering again the
hdmi-codec.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To handle jack event and configuration of the pin widget for MST
capable pin, this patch adds:
o Flag to identify the pin is MST capable.
o In notify callback(), based on the pipe and port information marks if
the port is mst_capable. In case of non MST, port is defaulted to zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in nau88l25_ssm4567 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in nau88l25_max98357a machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in bxt_rt298 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With MST each pin contains several ports to which device can be
connected.
As a preparatory work to support DP MST this patch adds below changes:
1. Defines the port structure and moves all stream related information
like ELD, converter list, chmap to port.
2. Creates ports for each pin based on the max_ports support.
3. Based on Pin-Port combination creates DAPM Mux widget instead of Pin
to allow user to select a converter.
4. Port zero is the default port when pin does not support MST.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two front-ends to the codec can now be selected individually, but fail to
build when the bus support is missing:
sound/built-in.o: In function `es8328_spi_probe':
es8328-spi.c:(.text+0x125854): undefined reference to `__devm_regmap_init_spi'
sound/built-in.o: In function `es8328_spi_driver_init':
es8328-spi.c:(.init.text+0x3589): undefined reference to `__spi_register_driver'
Related to this, the added dependency on SND_SOC_ES8328 breaks:
warning: (SND_SOC_ALL_CODECS) selects SND_SOC_ES8328_I2C which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && SND_SOC_ES8328 && I2C)
This adds the respective Kconfig dependencies and changes SND_SOC_ES8328 to a hidden
symbol that is selected implicitly by the two more specific options, as we do for
some other codecs. We have to remove the 'depends on' for SND_SOC_IMX_ES8328 in the
same step to avoid a recursive dependency.
Fixes: aa00f2c8af ("ASoC: Allow to select ES8328_I2C and ES8328_SPI directly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch create entry in sysfs file system to report the
platform_id = "pci-id-oem_id-oem_table_id-oem_revision"
for board identification.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Sodhi, VunnyX <vunnyx.sodhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we have to select these symbols explictly via Kconfig, from
another entry. If we plan to use generic audio drivers like
simple-audio-card, the user need to be able to enable these symbols
directly via the menuconfig.
This commit also fixes unmet dependencies to SND_SOC_IMX_ES8328 caused
by these changes.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the function that changes the DAI format only supports master
mode. Trying to use a slave mode exits the function with -EINVAL and
leave the codec misconfigured. This commits adds support for enabling
the slave mode.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in bxt_da7219_max98357a machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST moved pin to port, this changes the routes based on
port. So change the route in skl_rt286 machine.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HDMI registers channel map controls per pcm. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which registers
channel map in the late probe callback handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Channel info is part of the pcm parameter and channel map control is
created for each pcm. So move channel info to pcm instead of pin
structure and the mutex lock to pcm.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a relict of 6553bf06a3 ("ASoC: Don't try to register debugfs
entries if the parent does not exist").
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sync convert rate settings should be availabled *after* Playing.
Thus, src->sync should be reset first of init function.
Otherwise, it will set remaining settings when it start playing.
This patch fixes it. Thanks to Yokoyama-san
Reported-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
