Currently the proto argument is unused. This is because the driver only
supports 802.1Q VLAN filtering. This policy is enforced via netdev
features that the driver sets up when configuring the netdev, so the
proto argument won't ever be anything other than 802.1Q. However, this
will allow for future iterations of the driver to seemlessly support
802.1ad filtering. Begin using the proto argument and extend the related
structures to support its use.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new struct for VLAN related information. Currently this holds
VLAN ID and priority values, but will be expanded to hold TPID value.
This reduces the changes necessary if any other values are added in
future. Remove the action argument from these calls as it's always
ICE_FWD_VSI.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Incoming changes to support 802.1Q and/or 802.1ad VLAN filtering and
offloads require more flexibility when configuring VLANs. The VSI VLAN
interface will allow flexibility for configuring VLANs for all VSI
types. Add new files to separate the VSI VLAN ops and move functions to
make the code more organized.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
XDP_TX workloads use a concept of Tx threshold that indicates the
interval of setting RS bit on descriptors which in turn tells the HW to
generate an interrupt to signal the completion of Tx on HW side. It is
currently based on a constant value of 32 which might not work out well
for various sizes of ring combined with for example batch size that can
be set via SO_BUSY_POLL_BUDGET.
Internal tests based on AF_XDP showed that most convenient setup of
mentioned threshold is when it is equal to quarter of a ring length.
Make use of recently introduced ICE_RING_QUARTER macro and use this
value as a substitute for ICE_TX_THRESH.
Align also ethtool -G callback so that next_dd/next_rs fields are up to
date in terms of the ring size.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20220125160446.78976-5-maciej.fijalkowski@intel.com
In current switchdev implementation, every VF PR is assigned to
individual ring on switchdev ctrl VSI. For slow-path traffic, there
is a mapping VF->ring done in software based on src_vsi value (by
calling ice_eswitch_get_target_netdev function).
With this change, HW solution is introduced which is more
efficient. For each VF, src MAC (VF's MAC) filter will be created,
which forwards packets to the corresponding switchdev ctrl VSI queue
based on src MAC address.
This filter has to be removed and then replayed in case of
resetting one VF. Keep information about this rule in repr->mac_rule,
thanks to that we know which rule has to be removed and replayed
for a given VF.
In case of CORE/GLOBAL all rules are removed
automatically. We have to take care of readding them. This is done
by ice_replay_vsi_adv_rule.
When driver leaves switchdev mode, remove all advanced rules
from switchdev ctrl VSI. This is done by ice_rem_adv_rule_for_vsi.
Flag repr->rule_added is needed because in some cases reset
might be triggered before VF sends request to add MAC.
Co-developed-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to enable flow-director filter when multiple TCs are
configured. Flow director filter can be configured using ethtool
(--config-ntuple option). When multiple TCs are configured, each
TC is mapped to an unique HW VSI. So VSI corresponding to queue
used in filter is identified and flow director context is updated
with correct VSI while configuring ntuple filter in HW.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an odd indent where some code was left indented, and causes smatch
to warn:
ice_log_pkg_init() warn: inconsistent indenting
While here, for consistency, add a break after the default case.
This commit has a Fixes: but we caught this while it was only in net-next.
Fixes: 247dd97d71 ("ice: Refactor status flow for DDP load")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20211221230538.2546315-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement support for the basic operations needed to enable the PTP
hardware clock on E822 devices.
This includes implementations for the various PHY access functions, as
well as the ability to start and stop the PHY timers. This is different
from the E810 device because the configuration depends on link speed, so
we cannot just start the PHYs immediately. We must wait until the link
is up to get proper values for the speed based initialization.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The PF reset does not reset PHC and PHY clocks so it's unnecessary to
stop them and reinitialize after the reset.
Configuring timestamping changes the VSI fields so it needs to be
performed after VSIs are initialized, which was not done in case of a
reset.
Suggested-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pasi Vaananen <pvaanane@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver had comments to the effect of: This flag should be set before
calling this function. While reviewing code it was found that there were
several violations of this policy, which could introduce hard to find
bugs or races.
Fix the violations of the "VSI DOWN state must be set before calling
ice_down" and make checking the state into code with a WARN_ON.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As all functions now return standard error codes, propagate the values
being returned instead of converting them to generic values.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
ice_status previously had a variable to contain these values where other
error codes had a variable as well. With ice_status now being an int,
there is no need for two variables to hold error values. In cases where
this occurs, remove one of the excess variables and use a single one.
Some initialization of variables are no longer needed and have been
removed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Clean up code after changing ice_status to int. Rearrange to fix reverse
Christmas tree and pull lines up where applicable.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Replace uses of ice_status to, as equivalent as possible, error codes.
Remove enum ice_status and its helper conversion function as they are no
longer needed.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
To prepare for removal of ice_status, change the variables from
ice_status to int. This eases the transition when values are changed to
return standard int error codes over enum ice_status.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Remove the ice_stat_str() function which prints the string
representation of the ice_status error code. With upcoming changes
moving away from ice_status, there will be no need for this function.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Before this change, final state of the DDP pkg load process was
dependent on many variables such as: ice_status, pkg version,
ice_aq_err. The last one had be stored in hw->pkg_dwnld_status.
It was impossible to conclude this state just from ice_status, that's
why logging process of DDP pkg load in the caller was a little bit
complicated.
With this patch new status enum is introduced - ice_ddp_state.
It covers all the possible final states of the loading process.
What's tricky for ice_ddp_state is that not only
ICE_DDP_PKG_SUCCESS(=0) means that load was successful. Actually
three states mean that:
- ICE_DDP_PKG_SUCCESS
- ICE_DDP_PKG_SAME_VERSION_ALREADY_LOADED
- ICE_DDP_PKG_COMPATIBLE_ALREADY_LOADED
ice_is_init_pkg_successful can tell that information.
One ddp_state should not be used outside of ice_init_pkg which is
ICE_DDP_PKG_ALREADY_LOADED. It is more generic, it is used in
ice_dwnld_cfg_bufs to see if pkg is already loaded. At this point
we can't use one of the specific one (SAME_VERSION, COMPATIBLE,
NOT_SUPPORTED) because we don't have information on the package
currently loaded in HW (we are before calling ice_get_pkg_info).
We can get rid of hw->pkg_dwnld_status because we are immediately
mapping aq errors to ice_ddp_state in ice_dwnld_cfg_bufs.
Other errors like ICE_ERR_NO_MEMORY, ICE_ERR_PARAM are mapped the
generic ICE_DDP_PKG_ERR.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some of the promiscuous mode functions take a boolean to indicate
set/clear, which affects readability. Refactor and provide an
interface for the promiscuous mode code with explicit set and clear
promiscuous mode operations.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver was zeroing live stats that could be fetched by
ndo_get_stats64 at any time. This could result in inconsistent
statistics, and the telltale sign was when reading stats frequently from
/proc/net/dev, the stats would go backwards.
Fix by collecting stats into a local, and delaying when we write to the
structure so it's not incremental.
Fixes: fcea6f3da5 ("ice: Add stats and ethtool support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If the hardware is constantly receiving unicast or broadcast packets
during driver load, the device previously counted many GLV_RDPC (VSI
dropped packets) events during init. This causes confusing dropped
packet statistics during driver load. The dropped packets counter
incrementing does stop once the driver finishes loading.
Avoid this problem by baselining our statistics at the end of driver
open instead of the end of probe.
Fixes: cdedef59de ("ice: Configure VSIs for Tx/Rx")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow support for 'enable_iwarp' and 'enable_roce' devlink params to turn
on/off iWARP or RoCE protocol support for E800 devices.
For example, a user can turn on iWARP functionality with,
devlink dev param set pci/0000:07:00.0 name enable_iwarp value true cmode runtime
This add an iWARP auxiliary rdma device, ice.iwarp.<>, under this PF.
A user request to enable both iWARP and RoCE under the same PF is rejected
since this device does not support both protocols simultaneously on the
same port.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Leszek Kaliszczuk <leszek.kaliszczuk@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, the vlan_promisc flag is used exclusively by VF VSI to
determine whether or not to toggle VLAN pruning along with
trusted/true-promiscuous mode. This is not needed for a couple of
reasons. First, trusted/true-promiscuous mode is only supposed to allow
all MAC filters within VLANs that a VF has added filters for, so VLAN
pruning should not be disabled. Second, the boolean argument makes the
function confusing and unintuitive. Remove this flag.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some devices have support for loading the PHY FW and in some cases this
can fail. When this fails, the FW will set the corresponding bit in the
link info structure. Also, the FW will send a link event if the correct
link event mask bit is set. Add support for printing an error message
when the PHY FW load fails during any link configuration flow and the
link event flow.
Since ice_check_module_power() is already doing something very similar
add a new function ice_check_link_cfg_err() so any failures reported in
the link info's link_cfg_err member can be printed in this one function.
Also, add the new ICE_FLAG_PHY_FW_LOAD_FAILED bit to the PF's flags so
we don't constantly print this error message during link polling if the
value never changed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add definition for VXLAN and Geneve dummy packet. Define VXLAN and
Geneve type of fields to match on correct UDP tunnel header.
Parse tunnel specific fields from TC tool like outer MACs, outer IPs,
outer destination port and VNI. Save values and masks in outer header
struct and move header pointer to inner to simplify parsing inner
values.
There are two cases for redirect action:
- from uplink to VF - TC filter is added on tunnel device
- from VF to uplink - TC filter is added on PR, for this case check if
redirect device is tunnel device
VXLAN example:
- create tunnel device
ip l add $VXLAN_DEV type vxlan id $VXLAN_VNI dstport $VXLAN_PORT \
dev $PF
- add TC filter (in switchdev mode)
tc filter add dev $VXLAN_DEV protocol ip parent ffff: flower \
enc_dst_ip $VF1_IP enc_key_id $VXLAN_VNI action mirred egress \
redirect dev $VF1_PR
Geneve example:
- create tunnel device
ip l add $GENEVE_DEV type geneve id $GENEVE_VNI dstport $GENEVE_PORT \
remote $GENEVE_IP
- add TC filter (in switchdev mode)
tc filter add dev $GENEVE_DEV protocol ip parent ffff: flower \
enc_key_id $GENEVE_VNI dst_ip $GENEVE1_IP action mirred egress \
redirect dev $VF1_PR
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement indirect notification mechanism to support offloading TC rules
on tunnel devices.
Keep indirect block list in netdev priv. Notification will call setting
tc cls flower function. For now we can offload only ingress type. Return
not supported for other flow block binder.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support to add/delete channel specific filter using tc-flower.
For now, only supported action is "skip_sw hw_tc <tc_num>"
Filter criteria is specific to channel and it can be
combination of L3, L3+L4, L2+L4.
Example:
MATCH criteria Action
---------------------------
src and/or dest IPv4[6]/mask -> Forward to "hw_tc <tc_num>"
dest IPv4[6]/mask + dest L4 port -> Forward to "hw_tc <tc_num>"
dest MAC + dest L4 port -> Forward to "hw_tc <tc_num>"
src IPv4[6]/mask + src L4 port -> Forward to "hw_tc <tc_num>"
src MAC + src L4 port -> Forward to "hw_tc <tc_num>"
Adding tc-flower filter for channel using "hw_tc"
-------------------------------------------------
tc qdisc add dev <ethX> clsact
Above two steps are only needed the first time when adding
tc-flower filter.
tc filter add dev <ethX> protocol ip ingress prio 1 flower \
dst_ip 192.168.0.1/32 ip_proto tcp dst_port 5001 \
skip_sw hw_tc 1
tc filter show dev <ethX> ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1 hw_tc 1
eth_type ipv4
ip_proto tcp
dst_ip 192.168.0.1
dst_port 5001
skip_sw
in_hw in_hw_count 1
Delete specific filter:
-------------------------
tc filter del dev <ethx> ingress pref 1 handle 0x1 flower
Delete All filters:
------------------
tc filter del dev <ethX> ingress
Co-developed-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support in driver for TC_QDISC_SETUP_MQPRIO. This support
enables instantiation of channels in HW using existing MQPRIO
infrastructure which is extended to be offloadable. This
provides a mechanism to configure dedicated set of queues for
each TC.
Configuring channels using "tc mqprio":
--------------------------------------
tc qdisc add dev <ethX> root mqprio num_tc 3 map 0 1 2 \
queues 4@0 4@4 4@8 hw 1 mode channel
Above command configures 3 TCs having 4 queues each. "hw 1 mode channel"
implies offload of channel configuration to HW. When driver processes
configuration received via "ndo_setup_tc: QDISC_SETUP_MQPRIO", each
TC maps to HW VSI with specified queues.
User can optionally specify bandwidth min and max rate limit per TC
(see example below). If shaper params like min and/or max bandwidth
rate limit are specified, driver configures VSI specific rate limiter
in HW.
Configuring channels and bandwidth shaper parameters using "tc mqprio":
----------------------------------------------------------------
tc qdisc add dev <ethX> root mqprio \
num_tc 4 map 0 1 2 3 queues 4@0 4@4 4@8 4@12 hw 1 mode channel \
shaper bw_rlimit min_rate 1Gbit 2Gbit 3Gbit 4Gbit \
max_rate 4Gbit 5Gbit 6Gbit 7Gbit
Command to view configured TCs:
-----------------------------
tc qdisc show dev <ethX>
Deleting TCs:
------------
tc qdisc del dev <ethX> root mqprio
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add infrastructure required for "ndo_setup_tc:qdisc_mqprio".
ice_vsi_setup is modified to configure traffic classes based
on mqprio data received from the stack. This includes low-level
functions to configure min, max rate-limit parameters in hardware
for traffic classes. Each traffic class gets mapped to a hardware
channel (VSI) which can be individually configured with different
bandwidth parameters.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As part of support for E810 XXV devices, some device ids were
inadvertently left out. Add those missing ids.
Fixes: 195fb97766 ("ice: add additional E810 device id")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
The driver was having trouble with unreliable latency when doing single
threaded ping-pong tests. This was root caused to the DIM algorithm
landing on a too slow interrupt value, which caused high latency, and it
was especially present when queues were being switched frequently by the
scheduler as happens on default setups today.
In attempting to improve this, we allow the upper rate limit for
interrupts to move to rate limit of 4 microseconds as a max, which means
that no vector can generate more than 250,000 interrupts per second. The
old config was up to 100,000. The driver previously tried to program the
rate limit too frequently and if the receive and transmit side were both
active on the same vector, the INTRL would be set incorrectly, and this
change fixes that issue as a side effect of the redesign.
This driver will operate from now on with a slightly changed DIM table
with more emphasis towards latency sensitivity by having more table
entries with lower latency than with high latency (high being >= 64
microseconds).
The driver also resets the DIM algorithm state with a new stats set when
there is no work done and the data becomes stale (older than 1 second),
for the respective receive or transmit portion of the interrupt.
Add a new helper for setting rate limit, which will be used more
in a followup patch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement ndo_set_vf_rate to support setting of min_tx_rate and
max_tx_rate; set the appropriate bandwidth in the scheduler for the
node representing the specified VF VSI.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Go through the code base and use ice_for_each_* macros. While at it,
introduce ice_for_each_xdp_txq() macro that can be used for looping over
xdp_rings array.
Commit is not introducing any new functionality.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Under rare circumstances there might be a situation where a requirement
of having XDP Tx queue per CPU could not be fulfilled and some of the Tx
resources have to be shared between CPUs. This yields a need for placing
accesses to xdp_ring inside a critical section protected by spinlock.
These accesses happen to be in the hot path, so let's introduce the
static branch that will be triggered from the control plane when driver
could not provide Tx queue dedicated for XDP on each CPU.
Currently, the design that has been picked is to allow any number of XDP
Tx queues that is at least half of a count of CPUs that platform has.
For lower number driver will bail out with a response to user that there
were not enough Tx resources that would allow configuring XDP. The
sharing of rings is signalled via static branch enablement which in turn
indicates that lock for xdp_ring accesses needs to be taken in hot path.
Approach based on static branch has no impact on performance of a
non-fallback path. One thing that is needed to be mentioned is a fact
that the static branch will act as a global driver switch, meaning that
if one PF got out of Tx resources, then other PFs that ice driver is
servicing will suffer. However, given the fact that HW that ice driver
is handling has 1024 Tx queues per each PF, this is currently an
unlikely scenario.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Optimize Tx descriptor cleaning for XDP. Current approach doesn't
really scale and chokes when multiple flows are handled.
Introduce two ring fields, @next_dd and @next_rs that will keep track of
descriptor that should be looked at when the need for cleaning arise and
the descriptor that should have the RS bit set, respectively.
Note that at this point the threshold is a constant (32), but it is
something that we could make configurable.
First thing is to get away from setting RS bit on each descriptor. Let's
do this only once NTU is higher than the currently @next_rs value. In
such case, grab the tx_desc[next_rs], set the RS bit in descriptor and
advance the @next_rs by a 32.
Second thing is to clean the Tx ring only when there are less than 32
free entries. For that case, look up the tx_desc[next_dd] for a DD bit.
This bit is written back by HW to let the driver know that xmit was
successful. It will happen only for those descriptors that had RS bit
set. Clean only 32 descriptors and advance the DD bit.
Actual cleaning routine is moved from ice_napi_poll() down to the
ice_xmit_xdp_ring(). It is safe to do so as XDP ring will not get any
SKBs in there that would rely on interrupts for the cleaning. Nice side
effect is that for rare case of Tx fallback path (that next patch is
going to introduce) we don't have to trigger the SW irq to clean the
ring.
With those two concepts, ring is kept at being almost full, but it is
guaranteed that driver will be able to produce Tx descriptors.
This approach seems to work out well even though the Tx descriptors are
produced in one-by-one manner. Test was conducted with the ice HW
bombarded with packets from HW generator, configured to generate 30
flows.
Xdp2 sample yields the following results:
<snip>
proto 17: 79973066 pkt/s
proto 17: 80018911 pkt/s
proto 17: 80004654 pkt/s
proto 17: 79992395 pkt/s
proto 17: 79975162 pkt/s
proto 17: 79955054 pkt/s
proto 17: 79869168 pkt/s
proto 17: 79823947 pkt/s
proto 17: 79636971 pkt/s
</snip>
As that sample reports the Rx'ed frames, let's look at sar output.
It says that what we Rx'ed we do actually Tx, no noticeable drops.
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 79842324.00 79842310.40 4678261.17 4678260.38 0.00 0.00 0.00 38.32
with tx_busy staying calm.
When compared to a state before:
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 90919711.60 42233822.60 5327326.85 2474638.04 0.00 0.00 0.00 43.64
it can be observed that the amount of txpck/s is almost doubled, meaning
that the performance is improved by around 90%. All of this due to the
drops in the driver, previously the tx_busy stat was bumped at a 7mpps
rate.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
With rings being split, it is now convenient to introduce a pointer to
XDP ring within the Rx ring. For XDP_TX workloads this means that
xdp_rings array access will be skipped, which was executed per each
processed frame.
Also, read the XDP prog once per NAPI and if prog is present, set up the
local xdp_ring pointer. Reading prog a single time was discussed in [1]
with some concern raised by Toke around dispatcher handling and having
the need for going through the RCU grace period in the ndo_bpf driver
callback, but ice currently is torning down NAPI instances regardless of
the prog presence on VSI.
Although the pointer to XDP ring introduced to Rx ring makes things a
lot slimmer/simpler, I still feel that single prog read per NAPI
lifetime is beneficial.
Further patch that will introduce the fallback path will also get a
profit from that as xdp_ring pointer will be set during the XDP rings
setup.
[1]: https://lore.kernel.org/bpf/87k0oseo6e.fsf@toke.dk/
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There has been a long lasting issue of improper xdp_rings indexing for
XDP_TX and XDP_REDIRECT actions. Given that currently rx_ring->q_index
is mixed with smp_processor_id(), there could be a situation where Tx
descriptors are produced onto XDP Tx ring, but tail is never bumped -
for example pin a particular queue id to non-matching IRQ line.
Address this problem by ignoring the user ring count setting and always
initialize the xdp_rings array to be of num_possible_cpus() size. Then,
always use the smp_processor_id() as an index to xdp_rings array. This
provides serialization as at given time only a single softirq can run on
a particular CPU.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.
Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.
Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.
Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.
Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.
Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This field is dead and driver is not making any use of it. Simply remove
it.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the remove path, there is an attempt to free the aux_idx IDA whether
it was allocated or not. This can potentially cause a crash when
unloading the driver on systems that do not initialize support for RDMA.
But, this free cannot be gated by the status bit for RDMA, since it is
allocated if the driver detects support for RDMA at probe time, but the
driver can enter into a state where RDMA is not supported after the IDA
has been allocated at probe time and this would lead to a memory leak.
Initialize aux_idx to an invalid value and check for a valid value when
unloading to determine if an IDA free is necessary.
Fixes: d25a0fc41c ("ice: Initialize RDMA support")
Reported-by: Jun Miao <jun.miao@windriver.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement ndo_setup_tc net device callback for TC HW offload on PF device.
ndo_setup_tc provides support for HW offloading various TC filters.
Add support for configuring the following filter with tc-flower:
- default L2 filters (src/dst mac addresses, ethertype, VLAN)
- variations of L3, L3+L4, L2+L3+L4 filters using advanced filters
(including ipv4 and ipv6 addresses).
Allow for adding/removing TC flows when PF device is configured in
eswitch switchdev mode. Two types of actions are supported at the
moment: FLOW_ACTION_DROP and FLOW_ACTION_REDIRECT.
Co-developed-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As resetting all VFs behaves mostly like creating new VFs also
eswitch infrastructure has to be recreated. The easiest way to
do that is to rebuild eswitch after resetting VFs.
Implement helper functions to start and stop all representors
queues. This is used to disable traffic on port representors.
In rebuild path:
- NAPI has to be disabled
- eswitch environment has to be set up
- new port representors have to be created, because the old
one had pointer to not existing VFs
- new control plane VSI ring should be remapped
- NAPI hast to be enabled
- rxdid has to be set to FLEX_NIC_2, because this descriptor id
support source_vsi, which is needed on control plane VSI queues
- port representors queues have to be started
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Only way to enable switchdev is to create VFs when the eswitch
mode is set to switchdev. Check if correct mode is set and
enable switchdev in function which creating VFs.
Disable switchdev when user change number of VFs to 0. Changing
eswitch mode back to legacy when VFs are created in switchdev
mode isn't allowed.
As switchdev takes care of managing filter rules, adding new
rules on VF is blocked.
In case of resetting VF driver has to update pointer in ice_repr
struct, because after reset VSI related things can change.
Co-developed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
New type of VSI has to be defined for switchdev control plane
VSI. Number of allocated Tx and Rx queue has to be equal to
amount of VFs, because each port representor should have one
Tx and Rx queue.
Also to not increase number of used irqs too much, control plane
VSI uses only one q_vector and handle all queues in one irq.
To allow handling all queues in one irq , new function to clean
msix for eswitch was introduced. This function will schedule napi
for each representor instead of scheduling it only for one like in
normal clean irq function.
Only one additional msix has to be requested. Always try to request
it in ice_ena_msix_range function.
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Switchdev environment has to be set up when user create VFs
and eswitch mode is switchdev. Release is done when user
delete all VFs.
Data path in this implementation is based on control plane VSI.
This VSI is used to pass traffic from port representors to
corresponding VFs and vice versa. Default TX rule has to be
added to forward packet to control plane VSI. This will redirect
packets from VFs which don't match other rules to control plane
VSI.
On RX side default rule is added on uplink VSI to receive all
traffic that doesn't match other rules. When setting switchdev
environment all other rules from VFs should be removed. Packet to
VFs will be forwarded by control plane VSI.
As VF without any mac rules can't send any packet because of
antispoof mechanism, VSI antispoof should be turned off on each VFs.
To send packet from representor to correct VSI, destination VSI
field in TX descriptor will have to be filled. Allow that by
setting destination override bit in control plane VSI security config.
Packet from VFs will be received on control plane VSI. Driver
should decide to which netdev forward the packet. Decision is
made based on src_vsi field from descriptor. There is a target
netdev list in control plane VSI struct which choose netdev
based on src_vsi number.
Co-developed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Keeping devlink port inside VSI data structure causes some issues.
Since VF VSI is released during reset that means that we have to
unregister devlink port and register it again every time reset is
triggered. With the new changes in devlink API it
might cause deadlock issues. After calling
devlink_port_register/devlink_port_unregister devlink API is going to
lock rtnl_mutex. It's an issue when VF reset is triggered in netlink
operation context (like setting VF MAC address or VLAN),
because rtnl_lock is already taken by netlink. Another call of
rtnl_lock from devlink API results in dead-lock.
By moving devlink port to PF/VF we avoid creating/destroying it
during reset. Since this patch, devlink ports are created during
ice_probe, destroyed during ice_remove for PF and created during
ice_repr_add, destroyed during ice_repr_rem for VF.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The messaging for unsupported module detection is different for
lenient mode and strict mode. Update the code to print the right
messaging for a given link mode.
Media topology conflict is not an error in lenient mode, so return
an error code only if not in lenient mode.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
DSCP a.k.a L3 QoS is only supported on certain devices. To enforce this,
this patch introduces a bitmap of features and helper functions.
The feature bitmap is set based on device IDs on driver init. Currently,
DSCP is the only feature in this bitmap, but there will be more in the
future. In the DCB netlink flow, check if the feature bit is set before
exercising DSCP.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement code to handle submission of APP TLV's
containing DSCP to TC mapping.
The first such mapping received on an interface
will cause that PF to switch to L3 DSCP QoS mode,
apply the default config for that mode, and apply
the received mapping.
Only one such mapping will be allowed per DSCP value,
and when the last DSCP mapping is deleted, the PF
will switch back into L2 VLAN QoS mode, applying the
appropriate default QoS settings.
L3 DSCP QoS mode will only be allowed in SW DCBx
mode, in other words, when the FW LLDP engine is
disabled. Commands that break this mutual exclusivity
will be blocked.
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Move devlink_registration routine to be the last command, when the
device is fully initialized.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF pointer is always valid when PCI core calls its .shutdown() and
.remove() callbacks. There is no need to check it again.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink_register() can't fail and always returns success, but all drivers
are obligated to check returned status anyway. This adds a lot of boilerplate
code to handle impossible flow.
Make devlink_register() void and simplify the drivers that use that
API call.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com> # dsa
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some circumstances, such as with bridging, it's possible that the
stack will add the device's own MAC address to its unicast address list.
If, later, the stack deletes this address, the driver will receive a
request to remove this address.
The driver stores its current MAC address as part of the VSI MAC filter
list instead of separately. So, this causes a problem when the device's
MAC address is deleted unexpectedly, which results in traffic failure in
some cases.
The following configuration steps will reproduce the previously
mentioned problem:
> ip link set eth0 up
> ip link add dev br0 type bridge
> ip link set br0 up
> ip addr flush dev eth0
> ip link set eth0 master br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> modprobe -r veth
> modprobe -r bridge
> ip addr add 192.168.1.100/24 dev eth0
The following ping command fails due to the netdev->dev_addr being
deleted when removing the bridge module.
> ping <link partner>
Fix this by making sure to not delete the netdev->dev_addr during MAC
address sync. After fixing this issue it was noticed that the
netdev_warn() in .set_mac was overly verbose, so make it at
netdev_dbg().
Also, there is a possibility of a race condition between .set_mac and
.set_rx_mode. Fix this by calling netif_addr_lock_bh() and
netif_addr_unlock_bh() on the device's netdev when the netdev->dev_addr
is going to be updated in .set_mac.
Fixes: e94d447866 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Liang Li <liali@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The userspace utility "driverctl" can be used to change/override the
system's default driver choices. This is useful in some situations
(buggy driver, old driver missing a device ID, trying a workaround,
etc.) where the user needs to load a different driver.
However, this is also prone to user error, where a driver is mapped
to a device it's not designed to drive. For example, if the ice driver
is mapped to driver iavf devices, the ice driver crashes.
Add a check to return an error if the ice driver is being used to
probe a virtual function.
Fixes: 837f08fdec ("ice: Add basic driver framework for Intel(R) E800 Series")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The E810 device supports programmable pins for enabling both input and
output events related to the PTP hardware clock. This includes both
output signals with programmable period, as well as timestamping of
events on input pins.
Add support for enabling these using the CONFIG_PTP_1588_CLOCK
interface.
This allows programming the software defined pins to take advantage of
the hardware clock features.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch is modeled after one by Scott Peterson for i40e.
Add tracepoints to the driver, via a new file ice_trace.h and some new
trace calls added in interesting places in the driver. Add some tracing
for DIMLIB to help debug interrupt moderation problems.
Performance should not be affected, and this can be very useful
for debugging and adding new trace events to paths in the future.
Note eBPF programs can attach to these events, as well as perf
can count them since we're attaching to the events subsystem
in the kernel.
Co-developed-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove the local variable since it's only used once. Instead, use it
directly.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are some places where the scope of a variable can
be reduced so do that.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for enabling Tx timestamp requests for outgoing packets on
E810 devices.
The ice hardware can support multiple outstanding Tx timestamp requests.
When sending a descriptor to hardware, a Tx timestamp request is made by
setting a request bit, and assigning an index that represents which Tx
timestamp index to store the timestamp in.
Hardware makes no effort to synchronize the index use, so it is up to
software to ensure that Tx timestamp indexes are not re-used before the
timestamp is reported back.
To do this, introduce a Tx timestamp tracker which will keep track of
currently in-use indexes.
In the hot path, if a packet has a timestamp request, an index will be
requested from the tracker. Unfortunately, this does require a lock as
the indexes are shared across all queues on a PHY. There are not enough
indexes to reliably assign only 1 to each queue.
For the E810 devices, the timestamp indexes are not shared across PHYs,
so each port can have its own tracking.
Once hardware captures a timestamp, an interrupt is fired. In this
interrupt, trigger a new work item that will figure out which timestamp
was completed, and report the timestamp back to the stack.
This function loops through the Tx timestamp indexes and checks whether
there is now a valid timestamp. If so, it clears the PHY timestamp
indication in the PHY memory, locks and removes the SKB and bit in the
tracker, then reports the timestamp to the stack.
It is possible in some cases that a timestamp request will be initiated
but never completed. This might occur if the packet is dropped by
software or hardware before it reaches the PHY.
Add a task to the periodic work function that will check whether
a timestamp request is more than a few seconds old. If so, the timestamp
index is cleared in the PHY, and the SKB is released.
Just as with Rx timestamps, the Tx timestamps are only 40 bits wide, and
use the same overall logic for extending to 64 bits of nanoseconds.
With this change, E810 devices should be able to perform basic PTP
functionality.
Future changes will extend the support to cover the E822-based devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add SIOCGHWTSTAMP and SIOCSHWTSTAMP ioctl handlers to respond to
requests to enable timestamping support. If the request is for enabling
Rx timestamps, set a bit in the Rx descriptors to indicate that receive
timestamps should be reported.
Hardware captures receive timestamps in the PHY which only captures part
of the timer, and reports only 40 bits into the Rx descriptor. The upper
32 bits represent the contents of GLTSYN_TIME_L at the point of packet
reception, while the lower 8 bits represent the upper 8 bits of
GLTSYN_TIME_0.
The networking and PTP stack expect 64 bit timestamps in nanoseconds. To
support this, implement some logic to extend the timestamps by using the
full PHC time.
If the Rx timestamp was captured prior to the PHC time, then the real
timestamp is
PHC - (lower_32_bits(PHC) - timestamp)
If the Rx timestamp was captured after the PHC time, then the real
timestamp is
PHC + (timestamp - lower_32_bits(PHC))
These calculations are correct as long as neither the PHC timestamp nor
the Rx timestamps are more than 2^32-1 nanseconds old. Further, we can
detect when the Rx timestamp is before or after the PHC as long as the
PHC timestamp is no more than 2^31-1 nanoseconds old.
In that case, we calculate the delta between the lower 32 bits of the
PHC and the Rx timestamp. If it's larger than 2^31-1 then the Rx
timestamp must have been captured in the past. If it's smaller, then the
Rx timestamp must have been captured after PHC time.
Add an ice_ptp_extend_32b_ts function that relies on a cached copy of
the PHC time and implements this algorithm to calculate the proper upper
32bits of the Rx timestamps.
Cache the PHC time periodically in all of the Rx rings. This enables
each Rx ring to simply call the extension function with a recent copy of
the PHC time. By ensuring that the PHC time is kept up to date
periodically, we ensure this algorithm doesn't use stale data and
produce incorrect results.
To cache the time, introduce a kworker and a kwork item to periodically
store the Rx time. It might seem like we should use the .do_aux_work
interface of the PTP clock. This doesn't work because all PFs must cache
this time, but only one PF owns the PTP clock device.
Thus, the ice driver will manage its own kthread instead of relying on
the PTP do_aux_work handler.
With this change, the driver can now report Rx timestamps on all
incoming packets.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add a new ice_ptp.c file for holding the basic PTP clock interface
functions. If the device supports PTP, call the new ice_ptp_init and
ice_ptp_release functions where appropriate.
If the function owns the hardware resource associated with the PTP
hardware clock, register with the PTP_1588_CLOCK infrastructure to
allocate a new clock object that represents the device hardware clock.
Implement basic functionality for reading and setting the clock time,
performing clock adjustments, and adjusting the clock frequency.
Future changes will introduce functionality for handling related
features including Tx and Rx timestamps.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ice driver requires a programmable pipeline firmware package in order to
have a support for advanced features. Otherwise, driver falls back to so
called 'safe mode'. For that mode, ndo_bpf callback is not exposed and
when user tries to load XDP program, the following happens:
$ sudo ./xdp1 enp179s0f1
libbpf: Kernel error message: Underlying driver does not support XDP in native mode
link set xdp fd failed
which is sort of confusing, as there is a native XDP support, but not in
the current mode. Improve the user experience by providing the specific
ndo_bpf callback dedicated for safe mode which will make use of extack
to explicitly let the user know that the DDP package is missing and
that's the reason that the XDP can't be loaded onto interface currently.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Fixes: efc2214b60 ("ice: Add support for XDP")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After performing a flash update, a device EMP reset may occur. This
reset will cause the newly downloaded firmware to be initialized. When
this happens, the driver still reports the previous NVM version
information.
This is because the NVM versions are cached within the hw structure.
This can be confusing, as the new firmware is in fact running in this
case.
Handle this by calling ice_init_nvm when rebuilding the driver state.
This will update the flash version information and ensures that the
current values are displayed when reporting the NVM versions to the
stack.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Requesting device firmware information while the device is busy cleaning
up after a reset can result in an unexpected failure:
This occurs because the command is attempting to access the device
AdminQ while it is down. Resolve this by having the command wait for
a while until the reset is complete. To do this, introduce
a reset_wait_queue and associated helper function "ice_wait_for_reset".
This helper will use the wait queue to sleep until the driver is done
rebuilding. Use of a wait queue is preferred because the potential sleep
duration can be several seconds.
To ensure that the thread wakes up properly, a new wake_up call is added
during all code paths which clear the reset state bits associated with
the driver rebuild flow.
Using this ensures that tools can request device information without
worrying about whether the driver is cleaning up from a reset.
Specifically, it is expected that a flash update could result in
a device reset, and it is better to delay the response for information
until the reset is complete rather than exit with an immediate failure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Register ice client auxiliary RDMA device on the auxiliary bus per
PCIe device function for the auxiliary driver (irdma) to attach to.
It allows to realize a single RDMA driver (irdma) capable of working with
multiple netdev drivers over multi-generation Intel HW supporting RDMA.
There is no load ordering dependencies between ice and irdma.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Attempt to detect malicious VFs and, if suspected, log the information but
keep going to allow the user to take any desired actions.
Potentially malicious VFs are identified by checking if the VFs are
transmitting too many messages via the PF-VF mailbox which could cause an
overflow of this channel resulting in denial of service. This is done by
creating a snapshot or static capture of the mailbox buffer which can be
traversed and in which the messages sent by VFs are tracked.
Co-developed-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Co-developed-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.
It's more useful for debugging to see the driver name, as
most other modules do.
Here's a diff of before and after this change:
99100000-991fffff : 0000:3b:00.1
9a000000-a04fffff : PCI Bus 0000:3b
9a000000-9bffffff : 0000:3b:00.1
- 9a000000-9bffffff : 0000:3b:00.1
+ 9a000000-9bffffff : ice
9c000000-9dffffff : 0000:3b:00.0
- 9c000000-9dffffff : 0000:3b:00.0
+ 9c000000-9dffffff : ice
9e000000-9effffff : 0000:3b:00.1
9f000000-9fffffff : 0000:3b:00.0
a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.
The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.
The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.
The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).
There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.
The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ice_suspend(), ice_clear_interrupt_scheme() is called, and then
irq_free_descs() will be eventually called to free irq and its descriptor.
In ice_resume(), ice_init_interrupt_scheme() is called to allocate new
irqs. However, in ice_rebuild_arfs(), struct irq_glue and struct cpu_rmap
maybe cannot be freed, if the irqs that released in ice_suspend() were
reassigned to other devices, which makes irq descriptor's affinity_notify
lost.
So call ice_free_cpu_rx_rmap() before ice_clear_interrupt_scheme(), which
can make sure all irq_glue and cpu_rmap can be correctly released before
corresponding irq and descriptor are released.
Fix the following memory leak.
unreferenced object 0xffff95bd951afc00 (size 512):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
18 00 00 00 18 00 18 00 70 fc 1a 95 bd 95 ff ff ........p.......
00 00 ff ff 01 00 ff ff 02 00 ff ff 03 00 ff ff ................
backtrace:
[<0000000072e4b914>] __kmalloc+0x336/0x540
[<0000000054642a87>] alloc_cpu_rmap+0x3b/0xb0
[<00000000f220deec>] ice_set_cpu_rx_rmap+0x6a/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
unreferenced object 0xffff95bd81b0a2a0 (size 96):
comm "kworker/0:1", pid 134, jiffies 4294684283 (age 13051.958s)
hex dump (first 32 bytes):
38 00 00 00 01 00 00 00 e0 ff ff ff 0f 00 00 00 8...............
b0 a2 b0 81 bd 95 ff ff b0 a2 b0 81 bd 95 ff ff ................
backtrace:
[<00000000582dd5c5>] kmem_cache_alloc_trace+0x31f/0x4c0
[<000000002659850d>] irq_cpu_rmap_add+0x25/0xe0
[<00000000495a3055>] ice_set_cpu_rx_rmap+0xb4/0x110 [ice]
[<000000002370a632>] ice_probe+0x941/0x1180 [ice]
[<00000000d692edba>] local_pci_probe+0x47/0xa0
[<00000000503934f0>] work_for_cpu_fn+0x1a/0x30
[<00000000555a9e4a>] process_one_work+0x1dd/0x410
[<000000002c4b414a>] worker_thread+0x221/0x3f0
[<00000000bb2b556b>] kthread+0x14c/0x170
[<00000000ad2cf1cd>] ret_from_fork+0x1f/0x30
Fixes: 769c500dcc ("ice: Add advanced power mgmt for WoL")
Signed-off-by: Yongxin Liu <yongxin.liu@windriver.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Checkpatch reports the following, fix it.
-----------------------------------------
drivers/net/ethernet/intel/ice/ice_main.c
-----------------------------------------
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
FILE: drivers/net/ethernet/intel/ice/ice_main.c:455:
+
+}
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Currently the driver is doing two unnecessary checks. First both ops are
checking if the VLAN ID passed in is less than VLAN_N_VID and second
both ops are checking to see if a port VLAN is configured on the VSI.
The first check is already handled by the 8021q driver so this is an
unnecessary check. The second check is unnecessary because the PF VSI is
never put into a port VLAN.
Remove these checks.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tracking of the rx_gro_dropped statistic was removed in
commit f73fc40327 ("ice: drop dead code in ice_receive_skb()").
Remove the associated variables and its reporting to ethtool stats.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Replace multiple instances of vsi->back and pi->phy with equivalent
local variables
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_init_phy_user_cfg, vsi is used only to get to hw. Remove this
and just use pi->hw
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When link is owned by manageability, the driver is not allowed to fiddle
with link. FW returns ICE_AQ_RC_EMODE if the driver attempts to do so.
This patch adds a new function ice_set_link which abstracts the call to
ice_aq_set_link_restart_an and provides a clean way to turn on/off link.
While making this change, I also spotted that an int variable was being
used to hold both an ice_status return code and the Linux errno return
code. This pattern more often than not results in the driver inadvertently
returning ice_status back to kernel which is a major boo-boo. Clean it up.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For get PHY abilities AQ, the specification defines "report modes"
as "with media", "without media" and "active configuration". For
clarity, rename macros to align with the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
struct ice_vsi has two fields, state and flags which seem to
be serving the same purpose. Consolidate them into one field
'state'.
enum ice_state is used to represent state information of the PF.
While some of these enum values can be use to represent VSI state,
it makes more sense to represent VSI state with its own enum. So
derive a new enum ice_vsi_state from ice_vsi_flags and ice_state
and use it. Also rename enum ice_state to ice_pf_state for clarity.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently ice_set/get_rss are used to set/get the RSS LUT and/or RSS
key. However nearly everywhere these functions are called only the LUT
or key are set/get. Also, making this change reduces how many things
ice_set/get_rss are doing. Fix this by adding ice_set/get_rss_lut and
ice_set/get_rss_key functions.
Also, consolidate all calls for setting/getting the RSS LUT and RSS Key
to use ice_set/get_rss_lut() and ice_set/get_rss_key().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Update ice_aq_get_rss_lut() and ice_aq_set_rss_lut() to take a new
structure ice_aq_get_set_rss_params instead of passing individual
parameters. This is done for 2 reasons:
1. Reduce the number of parameters passed to the functions.
2. Reduce the amount of change required if the arguments ever need to be
updated in the future.
Also, reduce duplicate code that was checking for an invalid vsi_handle
and lut parameter by moving the checks to the lower level
__ice_aq_get_set_rss_lut().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
