Create if_rmnet.h and move the rmnet MAP packet structs to this
common include file. To account for portablity, add little and
big endian bitfield definitions similar to the ip & tcp headers.
The definitions in the headers can now be re-used by the
upcoming ipa driver series as well as qmi_wwan.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f8b9958534.
The reverted change instructed the QMan hardware block to fetch
RX frame annotation and beginning of frame data to cache before
the core would read them.
It turns out that in rare cases, it's possible that a QMan
stashing transaction is delayed long enough such that, by the time
it gets executed, the frame in question had already been dequeued
by the core and software processing began on it. If the core
manages to unmap the frame buffer _before_ the stashing transaction
is executed, an SMMU exception will be raised.
Unfortunately there is no easy way to work around this while keeping
the performance advantages brought by QMan stashing, so disable
it altogether.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for validating hardware filter spec configured in firmware
before offloading exact match flows.
Use the new fw api FW_PARAM_DEV_FILTER_MODE_MASK to read the filter mode
and mask from firmware. If the api isn't supported, then fall-back to
older way of reading just the mode from indirect register.
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal says:
====================
net: ll_temac: Fix and enable multicast support
This patch series makes the necessary fixes to ll_temac driver to make
multicast work, and enables support for it.so that multicast support can
The main change is the change from mutex to spinlock of the lock used to
synchronize access to the shared indirect register access.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast support have been tested and is working now.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid leaving old address table entries when using multicast. If more than
one multicast address were removed, only the first removed address would
actually be cleared.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With .ndo_set_rx_mode/temac_set_multicast_list() being called in atomic
context (holding addr_list_lock), and temac_set_multicast_list() needing
to access temac indirect registers, the mutex used to synchronize indirect
register is a no-no.
Replace it with a spinlock, and avoid sleeping in
temac_indirect_busywait().
To avoid excessive holding of the lock, which is now a spinlock, the
temac_device_reset() function is changed to only hold the lock for short
periods. With timeouts, it could be holding the spinlock for more than
2 seconds.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user has requested IFF_ALLMULTI or have set more than 4 multicast
addresses, we should just use promiscuous mode, but not set it in flags,
as it causes the interface to stay in promiscuous mode even when the
non-IFF_PROMISC condition that caused promiscuous mode to be enabled
has gone away.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All LXT PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic
genphy_{suspend,resume} functions added by
commit 0f0ca340e5 ("phy: power management support").
LXT970 is left aside because all registers get cleared upon
"power down" exit.
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent misbehavior of drivers who would not set port type for longer
period of time. Drivers should always set port type. Do WARN if that
happens.
Note that it is perfectly fine to temporarily not have the type set,
during initialization and port type change.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the hv_sock send() iterates once over the buffer, puts data into
the VMBUS channel and returns. It doesn't maximize on the case when there
is a simultaneous reader draining data from the channel. In such a case,
the send() can maximize the bandwidth (and consequently minimize the cpu
cycles) by iterating until the channel is found to be full.
Perf data:
Total Data Transfer: 10GB/iteration
Single threaded reader/writer, Linux hvsocket writer with Windows hvsocket
reader
Packet size: 64KB
CPU sys time was captured using the 'time' command for the writer to send
10GB of data.
'Send Buffer Loop' is with the patch applied.
The values below are over 10 iterations.
|--------------------------------------------------------|
| | Current | Send Buffer Loop |
|--------------------------------------------------------|
| | Throughput | CPU sys | Throughput | CPU sys |
| | (MB/s) | time (s) | (MB/s) | time (s) |
|--------------------------------------------------------|
| Min | 407 | 7.048 | 401 | 5.958 |
|--------------------------------------------------------|
| Max | 455 | 7.563 | 542 | 6.993 |
|--------------------------------------------------------|
| Avg | 440 | 7.411 | 451 | 6.639 |
|--------------------------------------------------------|
| Median | 446 | 7.417 | 447 | 6.761 |
|--------------------------------------------------------|
Observation:
1. The avg throughput doesn't really change much with this change for this
scenario. This is most probably because the bottleneck on throughput is
somewhere else.
2. The average system (or kernel) cpu time goes down by 10%+ with this
change, for the same amount of data transfer.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the hv_sock buffer size is static and can't scale to the
bandwidth requirements of the application. This change allows the
applications to influence the socket buffer sizes using the SO_SNDBUF and
the SO_RCVBUF socket options.
Few interesting points to note:
1. Since the VMBUS does not allow a resize operation of the ring size, the
socket buffer size option should be set prior to establishing the
connection for it to take effect.
2. Setting the socket option comes with the cost of that much memory being
reserved/allocated by the kernel, for the lifetime of the connection.
Perf data:
Total Data Transfer: 1GB
Single threaded reader/writer
Results below are summarized over 10 iterations.
Linux hvsocket writer + Windows hvsocket reader:
|---------------------------------------------------------------------------------------------|
|Packet size -> | 128B | 1KB | 4KB | 64KB |
|---------------------------------------------------------------------------------------------|
|SO_SNDBUF size | | Throughput in MB/s (min/max/avg/median): |
| v | |
|---------------------------------------------------------------------------------------------|
| Default | 109/118/114/116 | 636/774/701/700 | 435/507/480/476 | 410/491/462/470 |
| 16KB | 110/116/112/111 | 575/705/662/671 | 749/900/854/869 | 592/824/692/676 |
| 32KB | 108/120/115/115 | 703/823/767/772 | 718/878/850/866 | 1593/2124/2000/2085 |
| 64KB | 108/119/114/114 | 592/732/683/688 | 805/934/903/911 | 1784/1943/1862/1843 |
|---------------------------------------------------------------------------------------------|
Windows hvsocket writer + Linux hvsocket reader:
|---------------------------------------------------------------------------------------------|
|Packet size -> | 128B | 1KB | 4KB | 64KB |
|---------------------------------------------------------------------------------------------|
|SO_RCVBUF size | | Throughput in MB/s (min/max/avg/median): |
| v | |
|---------------------------------------------------------------------------------------------|
| Default | 69/82/75/73 | 313/343/333/336 | 418/477/446/445 | 659/701/676/678 |
| 16KB | 69/83/76/77 | 350/401/375/382 | 506/548/517/516 | 602/624/615/615 |
| 32KB | 62/83/73/73 | 471/529/496/494 | 830/1046/935/939 | 944/1180/1070/1100 |
| 64KB | 64/70/68/69 | 467/533/501/497 | 1260/1590/1430/1431 | 1605/1819/1670/1660 |
|---------------------------------------------------------------------------------------------|
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing two 4 bytes holes allows to use kmalloc-32
kmem cache instead of kmalloc-64 on 64bit kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tracepoint to __neigh_create to enable debugging of new entries.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The point of the pause-on-fail argument is to leave the setup as is after
a test fails to allow a user to debug why it failed. Move the cleanup
after posting the result to the user to make it so.
Random names for the namespaces are not user friendly when trying to
debug a failure. Make them simpler and more direct for the tests. Run
cleanup at the beginning to ensure they are cleaned up if they already
exist.
Remove cleanup_done. There is no harm in doing cleanup twice; just
ignore any errors related to not existing - which is already done.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add VERBOSE argument to fib-onlink-tests.sh and make output quiet by
default. Add getopt parsing of inputs and support for -v (verbose) and
-p (pause on fail).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New userspace on an older kernel can send unknown and unsupported
attributes resulting in an incompelete config which is almost
always wrong for routing (few exceptions are passthrough settings
like the protocol that installed the route).
Set strict_start_type in the policies for IPv4 and IPv6 routes and
rules to detect new, unsupported attributes and fail the route add.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
net: Export functions for nexthop code
This set exports ipv4 and ipv6 fib functions for use by the nexthop
code. It also adds new ones to send route notifications if a nexthop
configuration changes.
v2
- repost of patches dropped at the end of the last dev window
added patch 8 which exports nh_update_mtu since it is inline with
the other patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename nh_update_mtu to fib_nhc_update_mtu and export for use by the
nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add scope as input argument versus relying on fib_info reference in
fib_nh, and export fib_info_update_nh_saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As nexthops are deleted, fib entries referencing it are marked dead.
Export fib_flush so those entries can be removed in a timely manner.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change fib_check_nh to take net, table and scope as input arguments
over struct fib_config and export for use by nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib_info_notify_update to walk the fib and send RTM_NEWROUTE
notifications with NLM_F_REPLACE set for entries linked to a fib_info
that have nh_updated flag set. This helper will be used by the nexthop
code to notify userspace of routes that are impacted when a nexthop
config is updated via replace. The new function and its helper are
similar to how fib_flush and fib_table_flush work for address delete
and link down events.
This notification is needed for legacy apps that do not understand
the new nexthop object. Apps that are nexthop aware can use the
RTA_NH_ID attribute in the route notification to just ignore it.
In the future this should be wrapped in a sysctl to allow OS'es that
are fully updated to avoid the notificaton storm.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib6_rt_update to send RTM_NEWROUTE with NLM_F_REPLACE set. This
helper will be used by the nexthop code to notify userspace of routes
that are impacted when a nexthop config is updated via replace.
This notification is needed for legacy apps that do not understand
the new nexthop object. Apps that are nexthop aware can use the
RTA_NH_ID attribute in the route notification to just ignore it.
In the future this should be wrapped in a sysctl to allow OS'es that
are fully updated to avoid the notificaton storm.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hook to ipv6 stub to bump the sernum up to the root node for a
route. This is needed by the nexthop code when a nexthop config changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip6_del_rt to the IPv6 stub. The hook is needed by the nexthop
code to remove entries linked to a nexthop that is getting deleted.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
net: phy: T1 support
T1 PHYs make use of a single twisted pair, rather than the traditional
2 pair for 100BaseT or 4 pair for 1000BaseT. This patchset adds link
modes for 100BaseT1 and 1000BaseT1, and them makes use of 100BaseT1 in
the list of PHY features used by current T1 drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a link mode for 100BaseT1, use it in
phy_basic_t1_features so T1 PHY drivers will indicate this mode via
the Ethtool API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add link modes for 100Mbps and 1Gbps over a single pair.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was being done in config the first time the phy was configured.
Should be in the probe method.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insure property is in valid range and fail when reading DT if it is not.
Also add error message for existing failure if required property is not
present.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver would only set the IO impedance value when RGMII internal
delays were enabled. There is no reason for this. Move the IO
impedance block out of the RGMII delay block.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables used to store u32 DT properties were signed ints. This
doesn't work properly if the value of the property were to overflow.
Use unsigned variables so this doesn't happen.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was assuming the reset default of the delay control register
was to have delay disabled. This is what the datasheet shows as the
register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
If the interface mode is selected as RX or TX delay only, insure the
other direction's delay is disabled.
If the interface mode is just "rgmii", with neither TX or RX internal
delay, one might expect that the driver should disable both delays. But
this is not what the driver does. It leaves the setting at the PHY's
strapping's default. And that default, for no pins with strapping
resistors, is to have delay enabled and 2.00 ns.
Rather than change this behavior, I've kept it the same and documented
it. No delay will most likely not work and will break ethernet on any
board using "rgmii" mode. If the board is strapped to have a delay and
is configured to use "rgmii" mode a warning is generated that "rgmii-id"
should have been used.
Also validate the delay values and fail if they are not in range.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generally, the output clock pin is only used for testing and only serves
as a source of RF noise after this. It could be used to daisy-chain
PHYs, but this is uncommon. Since the PHY can disable the output, make
doing so an option. I do this by adding another enumeration to the
allowed values of ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep
clock output setting as is", which, depending on PHY strapping, might
not be outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the
previous behavior in this case).
Out of range values were silently converted into
DP83867_CLK_O_SEL_REF_CLK. Change this so they generate an error.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock output is generally only used for testing and development and
not used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a note to make it more clear how the driver behaves when "rgmii" vs
"rgmii-id", "rgmii-idrx", or "rgmii-idtx" interface modes are selected.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hash (exact-match) filters used for offloading flows share the
same active region resources on the chip with upper layer drivers,
like iw_cxgb4, chcr, etc. Currently, only either Hash filters
or ULDs can use the active region resources, but not both. Hence,
use the new firmware configuration parameters (when available)
to allow both the Hash filters and ULDs to share the
active region simultaneously.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't disable the ipg clock in the regulator error path. The clock is
disable unconditionally two lines below the failed_regulator label.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ability for Netlink to report a socket's UID along with the
other UNIX diagnostic information that is already available. This will
allow diagnostic tools greater insight into which users control which
socket.
To test this, do the following as a non-root user:
unshare -U -r bash
nc -l -U user.socket.$$ &
.. and verify from within that same session that Netlink UNIX socket
diagnostics report the socket's UID as 0. Also verify that Netlink UNIX
socket diagnostics report the socket's UID as the user's UID from an
unprivileged process in a different session. Verify the same from
a root process.
Signed-off-by: Felipe Gasper <felipe@felipegasper.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix SPE probe failure when backing auxbuf with high-order pages
- Fix handling of DMA allocations from outside of the vmalloc area
- Fix generation of build-id ELF section for vDSO object
- Disable huge I/O mappings if kernel page table dumping is enabled
- A few other minor fixes (comments, kconfig etc)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzlRT0ACgkQt6xw3ITB
YzRGOwgArUDryBedDdkxAvjx7fk8O+qjtWctAhdPtyuXIvVLOc3tpiKlayCguF/a
clqr4qAfxswoDLHRMwhh7xdv955A2vraHQWlzvGUj2O2M4mG8RdbVJLm3NxpA09m
dufjSuFcwxcou2c4rXbSXSB4AYJXPmQJiad04VsWj68+TVehy0P45zaPcjHsPNPI
D9sTa9XhBlNa0qpJG7tP9T8FS/QP/hpWHn8v0z/DQ4QetKRTstkpwD5kmJox8WmM
Bw593bvQQ2+5q9g+z0FM3M/7yHwTJw2RLnnIb29YsW8MxM3rUeqt+FMA2OALBgbi
0m7WoTZwO9hDQuPU1DDvZUtw3iOpeg==
=buiS
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix SPE probe failure when backing auxbuf with high-order pages
- Fix handling of DMA allocations from outside of the vmalloc area
- Fix generation of build-id ELF section for vDSO object
- Disable huge I/O mappings if kernel page table dumping is enabled
- A few other minor fixes (comments, kconfig etc)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: vdso: Explicitly add build-id option
arm64/mm: Inhibit huge-vmap with ptdump
arm64: Print physical address of page table base in show_pte()
arm64: don't trash config with compat symbol if COMPAT is disabled
arm64: assembler: Update comment above cond_yield_neon() macro
drivers/perf: arm_spe: Don't error on high-order pages for aux buf
arm64/iommu: handle non-remapped addresses in ->mmap and ->get_sgtable
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
doesn't properly trim special IOs (e.g. discards) relative to
corresponding target's max_io_len_target_boundary().
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEJfWUX4UqZ4x1O2wixSPxCi2dA1oFAlzkicQTHHNuaXR6ZXJA
cmVkaGF0LmNvbQAKCRDFI/EKLZ0DWuRcCADKc4zew1EAhcHjwanfWoQ2d+5ONdxv
Ir1yiQX3hqK96G1Vu4IROsxWPDgNBI+60HwWI0z3/nMdv4F9a9Tfowl9fcKgZNey
jGrzP7x1+9GPtJY0BIpFUQ895qC75wXdd0c6HjmM5IaN0DRrv783ZMMBNhS6yx84
2vDThiEpGiDKUXHTP9b1khUbZzvkpTmlk293UlkFDftgejfW5mq1FqbjLfACMNVI
Nh7D6A7MjFrEKHjvNbiGgeFn93iW1+XqGbsFobuCV8Z4A0ImD85H78Lesri2qrRG
nxGfTZMyq++SGSOV/JTzZ4k/qkZfkrDyljYiPaTgZpCi1mZYQ6wH8+7u
=oKZ5
-----END PGP SIGNATURE-----
Merge tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a particularly glaring oversight in a DM core commit from 5.1 that
doesn't properly trim special IOs (e.g. discards) relative to
corresponding target's max_io_len_target_boundary()"
* tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: make sure to obey max_io_len_target_boundary
Commit 4d207133e9 changed the types of the statistic values in struct
gfs2_lkstats from s64 to u64. Because of that, what should be a signed
value in gfs2_update_stats turned into an unsigned value. When shifted
right, we end up with a large positive value instead of a small negative
value, which results in an incorrect variance estimate.
Fixes: 4d207133e9 ("gfs2: Make statistics unsigned, suitable for use with do_div()")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Cc: stable@vger.kernel.org # v4.4+
Commit 61697a6abd ("dm: eliminate 'split_discard_bios' flag from DM
target interface") incorrectly removed code from
__send_changing_extent_only() that is required to impose a per-target IO
boundary on IO that exceeds max_io_len_target_boundary(). Otherwise
"special" IO (e.g. DISCARD, WRITE SAME, WRITE ZEROES) can write beyond
where allowed.
Fix this by restoring the max_io_len_target_boundary() limit in
__send_changing_extent_only()
Fixes: 61697a6abd ("dm: eliminate 'split_discard_bios' flag from DM target interface")
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Michael Lass <bevan@bi-co.net>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When disconnecting cdc_ncm the kernel sporadically crashes shortly
after the disconnect:
[ 57.868812] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 58.006653] PC is at 0x0
[ 58.009202] LR is at call_timer_fn+0xec/0x1b4
[ 58.013567] pc : [<0000000000000000>] lr : [<ffffff80080f5130>] pstate: 00000145
[ 58.020976] sp : ffffff8008003da0
[ 58.024295] x29: ffffff8008003da0 x28: 0000000000000001
[ 58.029618] x27: 000000000000000a x26: 0000000000000100
[ 58.034941] x25: 0000000000000000 x24: ffffff8008003e68
[ 58.040263] x23: 0000000000000000 x22: 0000000000000000
[ 58.045587] x21: 0000000000000000 x20: ffffffc68fac1808
[ 58.050910] x19: 0000000000000100 x18: 0000000000000000
[ 58.056232] x17: 0000007f885aff8c x16: 0000007f883a9f10
[ 58.061556] x15: 0000000000000001 x14: 000000000000006e
[ 58.066878] x13: 0000000000000000 x12: 00000000000000ba
[ 58.072201] x11: ffffffc69ff1db30 x10: 0000000000000020
[ 58.077524] x9 : 8000100008001000 x8 : 0000000000000001
[ 58.082847] x7 : 0000000000000800 x6 : ffffff8008003e70
[ 58.088169] x5 : ffffffc69ff17a28 x4 : 00000000ffff138b
[ 58.093492] x3 : 0000000000000000 x2 : 0000000000000000
[ 58.098814] x1 : 0000000000000000 x0 : 0000000000000000
...
[ 58.205800] [< (null)>] (null)
[ 58.210521] [<ffffff80080f5298>] expire_timers+0xa0/0x14c
[ 58.215937] [<ffffff80080f542c>] run_timer_softirq+0xe8/0x128
[ 58.221702] [<ffffff8008081120>] __do_softirq+0x298/0x348
[ 58.227118] [<ffffff80080a6304>] irq_exit+0x74/0xbc
[ 58.232009] [<ffffff80080e17dc>] __handle_domain_irq+0x78/0xac
[ 58.237857] [<ffffff8008080cf4>] gic_handle_irq+0x80/0xac
...
The crash happens roughly 125..130ms after the disconnect. This
correlates with the 'delay' timer that is started on certain USB tx/rx
errors in the URB completion handler.
The problem is a race of usbnet_stop() with usbnet_start_xmit(). In
usbnet_stop() we call usbnet_terminate_urbs() to cancel all URBs in
flight. This only makes sense if no new URBs are submitted
concurrently, though. But the usbnet_start_xmit() can run at the same
time on another CPU which almost unconditionally submits an URB. The
error callback of the new URB will then schedule the timer after it was
already stopped.
The fix adds a check if the tx queue is stopped after the tx list lock
has been taken. This should reliably prevent the submission of new URBs
while usbnet_terminate_urbs() does its job. The same thing is done on
the rx side even though it might be safe due to other flags that are
checked there.
Signed-off-by: Jan Klötzke <Jan.Kloetzke@preh.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
DEV_ADDR is defined but not used. Use it in address setting.
Do the same with IPv6 for consistency.
Reported-by: David Ahern <dsahern@gmail.com>
Fixes: fc82d93e57 ("selftests: fib_rule_tests: fix local IPv4 address typo")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some spelling typos found in ip-sysctl.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 does not consider if the socket is bound to a device when binding
to an address. The result is that a socket can be bound to eth0 and
then bound to the address of eth1. If the device is a VRF, the result
is that a socket can only be bound to an address in the default VRF.
Resolve by considering the device if sk_bound_dev_if is set.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
