Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
This tag contains fixes, defconfig, and DT data changes for the v5.2-rc
series. The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU doesn't
enter an infinite page fault loop;
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules;
- A udelay() fix for RV32, fixing a miscomputation of the delay time;
- Removal of deprecated smp_mb__*() barriers.
The tag also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEElRDoIDdEz9/svf2Kx4+xDQu9KksFAl0HtEkACgkQx4+xDQu9
KkuRIw//f2vSrUyMh44sevr6euVD0K++hQ0AbteQ94cGHqYWWaNxfwMHFD91Gxbj
wowTwgssq7H9nePsKANjiiLULnZNIkWXAlIncjzv3aXkH6JG3f9nEGR49yzvCbIZ
yN8wgElJ8rcVWLd096E53Su84CzxuJJ2o3wOI1nQi8aI4h3LwkM2b/O4GxZFpnWb
vIhWXqjvbUb8XL7Y+VPewtxnZItOUDHkuIkup4kP2bTgl2iDW93hzWwxNKbt6v+m
9wTzAChjcepCAXSmEGeeZ/h2HNqw2crs+NWOe0drcKxL2vKPZ6gS8ZRX/NuIoDr4
JgMILzYSO28z8N6w1cJJUdN4eGhCTvdxVTQXvkk/yZoT08X6M0xb5A1MbtizgOJ6
mZK/vM9gtuoUSZG0SRNeNoqHbWu1tIm29z435Be8hWAtzXlEfewJm8ntgFO4dGmb
E8TRSgjLzdHY0Nvwx/KVtvYmE/TMybVVRsxJJ525dqJlHT7f3VuRstvw7VQJQpz2
+JfsZbYk1KjbUc25QpAqF1LUxrRQFn2JL0Cqw+L49J8eshY77rsTcAKP6ZZWiSFZ
qodU0oPF4BkS1t0bnFuNwlqsAr/q9EiAnQO7+SvqQY/ZUnMNk9gCNn5k/rHMCfyD
2Dyo6iAbj+Yyb1rrQxX6QnlbHgpFxsG3N4s9E5jOPgKyEQM4JQ4=
=aotJ
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"This contains fixes, defconfig, and DT data changes for the v5.2-rc
series.
The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU
doesn't enter an infinite page fault loop
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules
- A udelay() fix for RV32, fixing a miscomputation of the delay time
- Removal of deprecated smp_mb__*() barriers
This also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build"
* tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove unused barrier defines
riscv: mm: synchronize MMU after pte change
riscv: dts: add initial board data for the SiFive HiFive Unleashed
riscv: dts: add initial support for the SiFive FU540-C000 SoC
dt-bindings: riscv: convert cpu binding to json-schema
dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540
arch: riscv: add support for building DTB files from DT source data
riscv: Fix udelay in RV32.
riscv: export pm_power_off again
RISC-V: defconfig: enable clocks, serial console
runnable_avg_yN_inv[] is only used in kernel/sched/pelt.c but was
included in several other places because they need other macros all
came from kernel/sched/sched-pelt.h which was generated by
Documentation/scheduler/sched-pelt. As the result, it causes compilation
a lot of warnings,
kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=]
kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=]
kernel/sched/sched-pelt.h:4:18: warning: 'runnable_avg_yN_inv' defined but not used [-Wunused-const-variable=]
...
Silence it by appending the __maybe_unused attribute for it, so all
generated variables and macros can still be kept in the same file.
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1559596304-31581-1-git-send-email-cai@lca.pw
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Recent probing at the Linux Kernel Memory Model uncovered a
'surprise'. Strongly ordered architectures where the atomic RmW
primitive implies full memory ordering and
smp_mb__{before,after}_atomic() are a simple barrier() (such as x86)
fail for:
*x = 1;
atomic_inc(u);
smp_mb__after_atomic();
r0 = *y;
Because, while the atomic_inc() implies memory order, it
(surprisingly) does not provide a compiler barrier. This then allows
the compiler to re-order like so:
atomic_inc(u);
*x = 1;
smp_mb__after_atomic();
r0 = *y;
Which the CPU is then allowed to re-order (under TSO rules) like:
atomic_inc(u);
r0 = *y;
*x = 1;
And this very much was not intended. Therefore strengthen the atomic
RmW ops to include a compiler barrier.
NOTE: atomic_{or,and,xor} and the bitops already had the compiler
barrier.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
At Rob's request, we're starting to migrate our DT binding
documentation to json-schema YAML format. Start by converting our cpu
binding documentation. While doing so, document more properties and
nodes. This includes adding binding documentation support for the E51
and U54 CPU cores ("harts") that are present on this SoC. These cores
are described in:
https://static.dev.sifive.com/FU540-C000-v1.0.pdf
This cpus.yaml file is intended to be a starting point and to
evolve over time. It passes dt-doc-validate as of the yaml-bindings
commit 4c79d42e9216.
This patch was originally based on the ARM json-schema binding
documentation as added by commit 672951cbd1 ("dt-bindings: arm: Convert
cpu binding to json-schema").
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Add YAML DT binding documentation for the SiFive FU540 SoC. This
SoC is documented at:
https://static.dev.sifive.com/FU540-C000-v1.0.pdf
Passes dt-doc-validate, as of yaml-bindings commit 4c79d42e9216.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f1 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup fixes from Tejun Heo:
"This has an unusually high density of tricky fixes:
- task_get_css() could deadlock when it races against a dying cgroup.
- cgroup.procs didn't list thread group leaders with live threads.
This could mislead readers to think that a cgroup is empty when
it's not. Fixed by making PROCS iterator include dead tasks. I made
a couple mistakes making this change and this pull request contains
a couple follow-up patches.
- When cpusets run out of online cpus, it updates cpusmasks of member
tasks in bizarre ways. Joel improved the behavior significantly"
* 'for-5.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: restore sanity to cpuset_cpus_allowed_fallback()
cgroup: Fix css_task_iter_advance_css_set() cset skip condition
cgroup: css_task_iter_skip()'d iterators must be advanced before accessed
cgroup: Include dying leaders with live threads in PROCS iterations
cgroup: Implement css_task_iter_skip()
cgroup: Call cgroup_release() before __exit_signal()
docs cgroups: add another example size for hugetlb
cgroup: Use css_tryget() instead of css_tryget_online() in task_get_css()
Instead of relying on rps_needed, it is safer to use a separate
static key, since we do not want to enable TCP rx_skb_cache
by default. This feature can cause huge increase of memory
usage on hosts with millions of sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mlx5 devlink health fw reporters and sw reset support
This series provides mlx5 firmware reset support and firmware devlink health
reporters.
1) Add initial mlx5 kernel documentation and include devlink health reporters
2) Add CR-Space access and FW Crdump snapshot support via devlink region_snapshot
3) Issue software reset upon FW asserts
4) Add fw and fw_fatal devlink heath reporters to follow fw errors indication by
dump and recover procedures and enable trigger these functionality by user.
4.1) fw reporter:
The fw reporter implements diagnose and dump callbacks.
It follows symptoms of fw error such as fw syndrome by triggering
fw core dump and storing it and any other fw trace into the dump buffer.
The fw reporter diagnose command can be triggered any time by the user to check
current fw status.
4.2) fw_fatal repoter:
The fw_fatal reporter implements dump and recover callbacks.
It follows fatal errors indications by CR-space dump and recover flow.
The CR-space dump uses vsc interface which is valid even if the FW command
interface is not functional, which is the case in most FW fatal errors. The
CR-space dump is stored as a memory region snapshot to ease read by address.
The recover function runs recover flow which reloads the driver and triggers fw
reset if needed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl0CsLgACgkQSD+KveBX
+j7mFwf+MYvIbUO4mXyoZIezci1UCzt1vNAkUYPceE94O9fK68ItrwtwrstgIqqS
58Tgx//MXxPpe9k9NIWjeS3i8sjcb8fDoqkjOCj7KAchv0IhSUvYFRpBrUK+yTOW
NIIXZzuCgIoR9a/hVlT/lhG+dm4MX2L5dWFtORLxMoO+ff3yiy4nNf9+Zdt0H7LT
YCELWnKeIQCvdzJAxX7OyTh3eOfc/h7o1nOsU4VugBHxKxx4T+9A26d+cZeZH5Ox
3ikTCc01ivVHqcLydAy96HQu0MENSNYNpmyDxWum3oJGFFu6hBQTM2ueRmVWZfwH
DRu+hhxONZROxxtpmP/ULmwYcLnBHg==
=VhXt
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-06-13
Mlx5 devlink health fw reporters and sw reset support
This series provides mlx5 firmware reset support and firmware devlink health
reporters.
1) Add initial mlx5 kernel documentation and include devlink health reporters
2) Add CR-Space access and FW Crdump snapshot support via devlink region_snapshot
3) Issue software reset upon FW asserts
4) Add fw and fw_fatal devlink heath reporters to follow fw errors indication by
dump and recover procedures and enable trigger these functionality by user.
4.1) fw reporter:
The fw reporter implements diagnose and dump callbacks.
It follows symptoms of fw error such as fw syndrome by triggering
fw core dump and storing it and any other fw trace into the dump buffer.
The fw reporter diagnose command can be triggered any time by the user to check
current fw status.
4.2) fw_fatal repoter:
The fw_fatal reporter implements dump and recover callbacks.
It follows fatal errors indications by CR-space dump and recover flow.
The CR-space dump uses vsc interface which is valid even if the FW command
interface is not functional, which is the case in most FW fatal errors. The
CR-space dump is stored as a memory region snapshot to ease read by address.
The recover function runs recover flow which reloads the driver and triggers fw
reset if needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Multipath hash policy value of 0 isn't distributing since the outer IP
dest and src aren't varied eventhough the inner ones are. Since the flow
is on the inner ones in the case of tunneled traffic, hashing on them is
desired.
This is done mainly for IP over GRE, hence only tested for that. But
anything else supported by flow dissection should work.
v2: Use skb_flow_dissect_flow_keys() directly so that other tunneling
can be supported through flow dissection (per Nikolay Aleksandrov).
v3: Remove accidental inclusion of ports in the hash keys and clarify
the documentation (Nikolay Alexandrov).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 series chips have a SYNCLKO pin which by default outputs a
25MHz clock, but some board setups require a 125MHz clock instead. Added
a microchip,synclko-125 device tree property to allow indicating a
125MHz clock output is required.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Permit mux_id values up to 254 to be used in qmimux_register_device()
for compatibility with ip(8) and the rmnet driver.
Fixes: c6adf77953 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=6C8e
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190614' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Remove references to old schedulers for the scheduler switching and
blkio controller documentation (Andreas)
- Kill duplicate check for report zone for null_blk (Chaitanya)
- Two bcache fixes (Coly)
- Ensure that mq-deadline is selected if zoned block device is enabled,
as we need that to support them (Damien)
- Fix io_uring memory leak (Eric)
- ps3vram fallout from LBDAF removal (Geert)
- Redundant blk-mq debugfs debugfs_create return check cleanup (Greg)
- Extend NOPLM quirk for ST1000LM024 drives (Hans)
- Remove error path warning that can now trigger after the queue
removal/addition fixes (Ming)
* tag 'for-linus-20190614' of git://git.kernel.dk/linux-block:
block/ps3vram: Use %llu to format sector_t after LBDAF removal
libata: Extend quirks for the ST1000LM024 drives with NOLPM quirk
bcache: only set BCACHE_DEV_WB_RUNNING when cached device attached
bcache: fix stack corruption by PRECEDING_KEY()
blk-mq: remove WARN_ON(!q->elevator) from blk_mq_sched_free_requests
blkio-controller.txt: Remove references to CFQ
block/switching-sched.txt: Update to blk-mq schedulers
null_blk: remove duplicate check for report zone
blk-mq: no need to check return value of debugfs_create functions
io_uring: fix memory leak of UNIX domain socket inode
block: force select mq-deadline for zoned block devices
Since commit 5b18b5a737 ("block: delete part_round_stats and switch to
less precise counting") io_ticks is approximated by adding one at each
start and end of requests if jiffies has changed.
This works perfectly for requests shorter than a jiffy. If requests runs
more than 2 jiffies some I/O time will not be accounted unless there are
other reuqests.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
powerpc architecture (both 64-bit and 32-bit) supports stack protector
mechanism since some time now [see commit 06ec27aea9 ("powerpc/64:
add stack protector support")].
Update stackprotector arch support documentation to reflect the same.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Update the documentation to reflect the new naming scheme with
latest changes.
Reported-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There's a paragraph that explains how to create fixed width text block,
but it doesn't explains how to create fixed width text inline, although
this feature is really used through the documentation. Fix that adding a
quick note about it.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Sphinx need to know when a paragraph ends. So, do some adjustments
at the file for it to be properly parsed.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
that's said, I believe that this file should be moved to the
GPU/DRM documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In order to prepare to add them to the Kernel API book,
convert the files to ReST format.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is a very trivial conversion: adjust the title markup
and add a few literal block markups to produce a better
visual when parsed and avoid warnings.
As newer documents related to xilinx could be added in the future,
create a new index file for it.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert those documents and prepare them to be part of the kernel
API book, as most of the stuff there are related to the
Kernel interfaces.
Still, in the future, it would make sense to split the docs,
as some of the stuff is clearly focused on sysadmin tasks.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion here is really trivial: just a bunch of title
markups and very few puntual changes is enough to make it to
be parsed by Sphinx and generate a nice html.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert the TCM docs to ReST format and add them to the
bookset.
This has a mix of userspace-faced and Kernelspace faced
docs. Still, it sounds a better candidate to be added at
the kernel API set of docs.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion here is trivial:
- Adjust the document title's markup
- Do some whitespace alignment;
- mark literal blocks;
- Use ReST way to markup indented lists.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion is trivial: just adjust title markups.
In order to avoid conflicts, let's add an :orphan: tag
to it, to be removed when this file gets added to the
driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This file is already in a good shape: just its title and
adding some literal block markups is needed for it to be
part of the document.
While it has a small chapter with sysfs stuff, most of
the document is focused on driver development.
As it describes a kernel API, move it to the driver-api
directory.
In order to avoid conflicts, let's add an :orphan: tag
to it, to be removed when added to the driver-api book.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert the cgroup-v1 files to ReST format, in order to
allow a later addition to the admin-guide.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert the pcmcia docs to ReST format. Most of the changes here
are trivial.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert netlabel documentation to ReST.
This was trivial: just add proper title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert Intel Many Integrated Core architecture docs to ReST.
The conversion is trivial: just add title and literal block
markups, and adjust some identation.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Convert kdump documentation to ReST and add it to the
user faced manual, as the documents are mainly focused on
sysadmins that would be enabling kdump.
Note: the vmcoreinfo.rst has one very long title on one of its
sub-sections:
PG_lru|PG_private|PG_swapcache|PG_swapbacked|PG_slab|PG_hwpoision|PG_head_mask|PAGE_BUDDY_MAPCOUNT_VALUE(~PG_buddy)|PAGE_OFFLINE_MAPCOUNT_VALUE(~PG_offline)
I opted to break this one, into two entries with the same content,
in order to make it easier to display after being parsed in html and PDF.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The dfl.txt file is almost there. It needs just a few
adjustments to be properly parsed.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Also, removed the Maintained by, as requested by Geert.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion is actually:
- add blank lines and indentation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The stuff there is almost already at ReST format. A
conversion for them is trivial: just add a missing titles
and fix some scape codes for them to match ReST syntax.
While here, rename the cdrom-standard.txt, with was converted
from LaTeX to ReST on the previous patch, and add it to the
index file.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is the only LaTeX documentation file inside the documentation.
Instead of having a Latex document directly there, convert
it to ReST format, as this is the format we're using for docs.
For now, let's keep the extension as .txt in order to avoid
warnings when building the documentation with Sphinx.
The next patch patch will rename it to .rst and add it to the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The documentation is in a format that is very close to ReST format.
The conversion is actually:
- add blank lines in order to identify paragraphs;
- fixing tables markups;
- adding some lists markups;
- marking literal blocks;
- adjust some title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are only two files within Documentation/aoe dir that are
documentation. The remaining ones are examples and shell
scripts.
Convert the two AoE files to ReST format, and add the others
as literal, as they're part of the documentation.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into mauro
We need to pick up post-rc1 changes to various document files so they don't
get lost in Mauro's massive RST conversion push.
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
-----BEGIN PGP SIGNATURE-----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=j+Um
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
x86 got added twice to the index via the RST conversion and the MDS
documentation changes. Remove one instance.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- Fix broken SVE ptrace API when running in a big-endian configuration
- Fix performance regression due to off-by-one in TLBI range checking
- Fix build regression when using Clang
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl0DsZ0ACgkQt6xw3ITB
YzRE3wf9GJibmSnm9q5gmtHcKMrH+atXrI93nyzhBZxYaAYAKSiz7RCMSpc7iudI
bGMruaaqn/2xrdOie3vOOfSqFfzrfcFOuh/0id9R2IyiFSg08BrI369buejNRtm+
BUhdUQCe5p5afJ7PYFa7CYD+tSC1WiHXfOhH6sRYllerwaMiR9y/eqf3Gh5zB26Q
ca/+2Jh59DxXIpSWP9nTzPyV9xKOJ1B8JdMR5BMIUnOgUXQhMwNeuivRrZnEG9yT
PZDGbk5WxKci+LHPOt7stFFuo7hZn3SCKJ0mZ20VUs0w7ETMJuI0Ss4TlE2mgYag
TASmsypuLdRz5mxIeyY5QYXppSyYiA==
=AhWz
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are some arm64 fixes for -rc5.
The only non-trivial change (in terms of the diffstat) is fixing our
SVE ptrace API for big-endian machines, but the majority of this is
actually the addition of much-needed comments and updates to the
documentation to try to avoid this mess biting us again in future.
There are still a couple of small things on the horizon, but nothing
major at this point.
Summary:
- Fix broken SVE ptrace API when running in a big-endian configuration
- Fix performance regression due to off-by-one in TLBI range checking
- Fix build regression when using Clang"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/sve: Fix missing SVE/FPSIMD endianness conversions
arm64: tlbflush: Ensure start/end of address range are aligned to stride
arm64: Don't unconditionally add -Wno-psabi to KBUILD_CFLAGS
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Quoting Paul [1]:
"Given that a quick (and perhaps error-prone) search of the uses
of rcu_assign_pointer() in v5.1 didn't find a single use of the
return value, let's please instead change the documentation and
implementation to eliminate the return value."
[1] https://lkml.kernel.org/r/20190523135013.GL28207@linux.ibm.com
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: rcu@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Sasha Levin <sashal@kernel.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Add binding documentation for the imx8qxp DDR performance monitor unit.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[will: Removed trailing newline]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The in-memory representation of SVE and FPSIMD registers is
different: the FPSIMD V-registers are stored as single 128-bit
host-endian values, whereas SVE registers are stored in an
endianness-invariant byte order.
This means that the two representations differ when running on a
big-endian host. But we blindly copy data from one representation
to another when converting between the two, resulting in the
register contents being unintentionally byteswapped in certain
situations. Currently this can be triggered by the first SVE
instruction after a syscall, for example (though the potential
trigger points may vary in future).
So, fix the conversion functions fpsimd_to_sve(), sve_to_fpsimd()
and sve_sync_from_fpsimd_zeropad() to swab where appropriate.
There is no common swahl128() or swab128() that we could use here.
Maybe it would be worth making this generic, but for now add a
simple local hack.
Since the byte order differences are exposed in ABI, also clarify
the documentation.
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alan Hayward <alan.hayward@arm.com>
Cc: Julien Grall <julien.grall@arm.com>
Fixes: bc0ee47603 ("arm64/sve: Core task context handling")
Fixes: 8cd969d28f ("arm64/sve: Signal handling support")
Fixes: 43d4da2c45 ("arm64/sve: ptrace and ELF coredump support")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[will: Fix typos in comments and docs spotted by Julien]
Signed-off-by: Will Deacon <will.deacon@arm.com>
CFQ is gone. No need anymore to document its "proportional weight time
based division of disk policy".
Signed-off-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove references to CFQ and legacy block layer which are gone.
Update example with what's available under blk-mq.
Signed-off-by: Andreas Herrmann <aherrmann@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rewrite the skcipher API example, changing it to encrypt a buffer with
AES-256-XTS. This addresses various problems with the previous example:
- It requests a specific driver "cbc-aes-aesni", which is unusual.
Normally users ask for "cbc(aes)", not a specific driver.
- It encrypts only a single AES block. For the reader, that doesn't
clearly distinguish the "skcipher" API from the "cipher" API.
- Showing how to encrypt something with bare CBC is arguably a poor
choice of example, as it doesn't follow modern crypto trends. Now,
usually authenticated encryption is recommended, in which case the
user would use the AEAD API, not skcipher. Disk encryption is still a
legitimate use for skcipher, but for that usually XTS is recommended.
- Many other bugs and poor coding practices, such as not setting
CRYPTO_TFM_REQ_MAY_SLEEP, unnecessarily allocating a heap buffer for
the IV, unnecessary NULL checks, using a pointless wrapper struct, and
forgetting to set an error code in one case.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a spelling typo in rds.txt
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bindings for Wiznet's w5x00 series of SPI interfaced Ethernet chips.
Based on the bindings for microchip,enc28j60.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When McASP is bus master it's reference clock (AUXCLK) might not be a
static clock, but running at a specific FS ratio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FMC subsystem was created in 2012 with the ambition to
drive development of drivers for this hardware upstream.
The current implementation has architectural flaws and would
need to be revamped using real hardware to something that can
reuse existing kernel abstractions in the subsystems for e.g.
I2C, FPGA and GPIO.
We have concluded that for the mainline kernel it will be
better to delete the subsystem and start over with a clean
slate when/if an active maintainer steps up.
For details see:
https://lkml.org/lkml/2018/10/29/534
Suggested-by: Federico Vaga <federico.vaga@cern.ch>
Cc: Pat Riehecky <riehecky@fnal.gov>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce a new type for reserved region. This corresponds
to directly mapped regions which are known to be relaxable
in some specific conditions, such as device assignment use
case. Well known examples are those used by USB controllers
providing PS/2 keyboard emulation for pre-boot BIOS and
early BOOT or RMRRs associated to IGD working in legacy mode.
Since commit c875d2c1b8 ("iommu/vt-d: Exclude devices using RMRRs
from IOMMU API domains") and commit 18436afdc1 ("iommu/vt-d: Allow
RMRR on graphics devices too"), those regions are currently
considered "safe" with respect to device assignment use case
which requires a non direct mapping at IOMMU physical level
(RAM GPA -> HPA mapping).
Those RMRRs currently exist and sometimes the device is
attempting to access it but this has not been considered
an issue until now.
However at the moment, iommu_get_group_resv_regions() is
not able to make any difference between directly mapped
regions: those which must be absolutely enforced and those
like above ones which are known as relaxable.
This is a blocker for reporting severe conflicts between
non relaxable RMRRs (like MSI doorbells) and guest GPA space.
With this new reserved region type we will be able to use
iommu_get_group_resv_regions() to enumerate the IOVA space
that is usable through the IOMMU API without introducing
regressions with respect to existing device assignment
use cases (USB and IGD).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
with DT bindings:
- leds-lm3697
- leds-lm36274
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXQAatQAKCRBiEGxRG/Sl
2/2KAQDHnHR0rIITh3hH49YutOCzGK4oaut8sXfy+8PTEdKBlQEApQP1O1RJTTws
/KDS8qpNdwOQOW/KYiYDX5R8GcOeZwg=
=we/t
-----END PGP SIGNATURE-----
Merge tag 'ti-lmu-led-drivers' into for-next
Merge immutable branch between LEDs, MFD and REGULATOR due to
TI LMU LED support rework and introduction of two new drivers
with DT bindings.
* tag 'ti-lmu-led-drivers':
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property
TLS offload drivers keep track of TCP seq numbers to make sure
the packets are fed into the HW in order.
When packets get dropped on the way through the stack, the driver
will get out of sync and have to use fallback encryption, but unless
TCP seq number is resynced it will never match the packets correctly
(or even worse - use incorrect record sequence number after TCP seq
wraps).
Existing drivers (mlx5) feed the entire record on every out-of-order
event, allowing FW/HW to always be in sync.
This patch adds an alternative, more akin to the RX resync. When
driver sees a frame which is past its expected sequence number the
stream must have gotten out of order (if the sequence number is
smaller than expected its likely a retransmission which doesn't
require resync). Driver will ask the stack to perform TX sync
before it submits the next full record, and fall back to software
crypto until stack has performed the sync.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TLS offload device may lose sync with the TCP stream if packets
arrive out of order. Drivers can currently request a resync at
a specific TCP sequence number. When a record is found starting
at that sequence number kernel will inform the device of the
corresponding record number.
This requires the device to constantly scan the stream for a
known pattern (constant bytes of the header) after sync is lost.
This patch adds an alternative approach which is entirely under
the control of the kernel. Kernel tracks records it had to fully
decrypt, even though TLS socket is in TLS_HW mode. If multiple
records did not have any decrypted parts - it's a pretty strong
indication that the device is out of sync.
We choose the min number of fully encrypted records to be 2,
which should hopefully be more than will get retransmitted at
a time.
After kernel decides the device is out of sync it schedules a
resync request. If the TCP socket is empty the resync gets
performed immediately. If socket is not empty we leave the
record parser to resync when next record comes.
Before resync in message parser we peek at the TCP socket and
don't attempt the sync if the socket already has some of the
next record queued.
On resync failure (encrypted data continues to flow in) we
retry with exponential backoff, up to once every 128 records
(with a 16k record thats at most once every 2M of data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into media/master
There are some conflicts due to SPDX changes. We also have more
patches being merged via media tree touching them.
So, let's merge back from upstream and address those.
Linux 5.2-rc4
* tag 'v5.2-rc4': (767 commits)
Linux 5.2-rc4
MAINTAINERS: Karthikeyan Ramasubramanian is MIA
i2c: xiic: Add max_read_len quirk
lockref: Limit number of cmpxchg loop retries
uaccess: add noop untagged_addr definition
x86/insn-eval: Fix use-after-free access to LDT entry
kbuild: use more portable 'command -v' for cc-cross-prefix
s390/unwind: correct stack switching during unwind
block, bfq: add weight symlink to the bfq.weight cgroup parameter
cgroup: let a symlink too be created with a cftype file
drm/nouveau/secboot/gp10[2467]: support newer FW to fix SEC2 failures on some boards
drm/nouveau/secboot: enable loading of versioned LS PMU/SEC2 ACR msgqueue FW
drm/nouveau/secboot: split out FW version-specific LS function pointers
drm/nouveau/secboot: pass max supported FW version to LS load funcs
drm/nouveau/core: support versioned firmware loading
drm/nouveau/core: pass subdev into nvkm_firmware_get, rather than device
block: free sched's request pool in blk_cleanup_queue
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add documentation for the meson vdec dts node.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add trigger type setting for csky,mpintc. The driver also could
support #interrupt-cells <1> and it wouldn't invalidate existing
DTs. Here we only show the complete format.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Update the dt-binding document to support new compatible string for the
GPIO interrupt controller which found in Amlogic's Meson-G12A SoC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Instead of keeping the documentation inside s390dbf.rst,
move them to arch/s390/include/asm/debug.h, using standard
kernel-doc markups.
Keeping the documentation close to the code helps to keep it
updated. It also makes easier to document other stuff inside
debug.h, as all it needs is to add kernel-doc markups inside
it, as the file will be already be included at the produced
documentation.
-
Those were converted to kerneldoc using this script specially
designed to parse ths file, and manually editted:
<script>
use strict;
my $mode = "";
my $parameter = "";
my $ret = "";
my $descr = "";
sub add_var($)
{
my $ln = shift;
$ln =~ s/^\s+//;
$ln =~ s/\s+$//;
return if ($ln eq "");
$ln =~ s/^(\S+)\s+/$1\t/;
print " * \@$ln\n";
}
sub add_return($)
{
my $ln = shift;
print " *\n * Return:\n" if ($mode ne "Return Value:");
$ln =~ s/^\s+//;
$ln =~ s/\s+$//;
return if ($ln eq "");
print " * - $ln\n";
}
sub add_description($)
{
my $ln = shift;
print " *\n * \n" if ($mode ne "Description:");
$ln =~ s/^\s+//;
$ln =~ s/\s+$//;
return if ($ln eq "");
print " * $ln\n";
}
sub flush_results()
{
print " */\n\n";
}
while (<>) {
if (m/^[\-]+$/) {
flush_results();
$mode = "";
$parameter = "";
$ret = "";
$descr = "";
next;
}
if (m/(Parameter:)(.*)/) {
print " *\n" if ($mode eq "func");
add_var($2);
$mode = $1;
next;
}
if (m/(Return Value:)(.*)/) {
add_return($2);
$mode = $1;
next;
}
if (m/(Description:)(.*)/) {
add_description($2);
$mode = $1;
next;
}
if ($mode eq "Parameter:") {
add_var($_);
next;
}
if ($mode eq "Return Value:") {
add_return($_);
next;
}
if ($mode eq "Description:") {
add_description($_);
next;
}
next if (m/^\s*$/);
if (m/^\S+.*\s\*?(\S+)\s*\(/) {
if ($mode eq "") {
print "/**\n * $1()\n";
} else {
print " * $1()\n";
}
$mode="func";
}
}
flush_results();
</script>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Convert all text files with s390 documentation to ReST format.
Tried to preserve as much as possible the original document
format. Still, some of the files required some work in order
for it to be visible on both plain text and after converted
to html.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The first bit/value table inside the document is very
hard to read and won't fit ReST format. Also, some columns aren't
properly aligned.
Convert it to a nice ascii artwork table with makes it easier to
read as plain text and is compatible with ReST format parser
on Sphinx.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAlz60fwTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdILI8B/41j6UxwMSYMetM/Vw2AyqPt0z671Gu
mAVzDK3PZF5WIzD5JsDlUhwN1dqvfvAZeSS1tQwQ18ZpQLkRSxlAKhkLLlxBVKpJ
0uDwYuFWwXF8DbdlRwZq+Db0GGAXW5+8WtA4gp9GTiIP6kTgmqnnaZvWPnQzQmKJ
RCY8YAzF52jXa4hBfLsXiG7NoO6cZHQJMFKLsQEpHV+GMqTcAYJHzBP6YVVXC8PG
495TREmTq5lvRKc2U3QS6//yPWleFYr5ViW/psEcBPCGdruyJI8LjDRaqnGWRBJX
vPyEVSFHtQZu49Vue3g4jbjhVr8OWTV/MsFgE/zK5Ahe+2G5969pID3n
=iCgZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.2-20190607' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-06-07
this is a pull reqeust of 9 patches for net/master.
The first patch is by Alexander Dahl and removes a duplicate menu entry from
the Kconfig. The next patch by Joakim Zhang fixes the timeout in the flexcan
driver when setting small bit rates. Anssi Hannula's patch for the xilinx_can
driver fixes the bittiming_const for CAN FD core. The two patches by Sean
Nyekjaer bring mcp25625 to the existing mcp251x driver. The patch by Eugen
Hristev implements an errata for the m_can driver. YueHaibing's patch fixes the
error handling ing can_init(). The patch by Fabio Estevam for the flexcan
driver removes an unneeded registration message during flexcan_probe(). And the
last patch is by Willem de Bruijn and adds the missing purging the socket
error queue on sock destruct.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Keystone 2 66AK2HK/E/L 1G Ethernet Switch Subsystems contains The
Common Platform Time Sync (CPTS) module which is in general compatible with
CPTS module found on "legacy" TI AM3/4/5 SoCs. So, the basic support for
Keystone 2 CPTS is available by default, but not documented.
The Keystone 2 CPTS module supports also some additional features like time
sync reference (RFTCLK) clock selection through CPTS_RFTCLK_SEL register
(offset: x08) in CPTS module, which is modelled as multiplexer clock.
This patch adds missed binding documentation for Keystone 2 66AK2HK/E/L
CPTS module.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some documentation files were still pointing to the old place.
Fixes: 229b4e0728 ("Documentation: PCI: convert pci.txt to reST")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
A recent documentation conversion renamed this file but forgot
to update the links.
Fixes: af96c1e304 ("docs: filesystems: vfs: Convert vfs.txt to RST")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The hisax driver got removed on 85993b8c97 ("isdn: remove hisax driver"),
but a left-over was kept at kernel-parameters.txt.
Fixes: 85993b8c97 ("isdn: remove hisax driver")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Mostly due to x86 and acpi conversion, several documentation
links are still pointing to the old file. Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This document is used by multiple architectures:
$ echo $(git grep -l pkey_mprotect arch|cut -d'/' -f 2|sort|uniq)
alpha arm arm64 ia64 m68k microblaze mips parisc powerpc s390 sh sparc x86 xtensa
So, let's move it to the core book and adjust the links to it
accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:43: WARNING: Definition list ends without a blank line; unexpected unindent.
Documentation/networking/device_drivers/freescale/dpaa2/dpio-driver.rst:63: WARNING: Unexpected indentation. looking for now-outdated files... none found
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There's a table there with produces two warnings when built
with Sphinx:
Documentation/networking/dsa/sja1105.rst:91: WARNING: Block quote ends without a blank line; unexpected unindent.
Documentation/networking/dsa/sja1105.rst:91: WARNING: Block quote ends without a blank line; unexpected unindent.
It will still produce a table, but the html output is wrong, as
it won't interpret the second line as the continuation for the
first ones, because identation doesn't match.
After the change, the output looks a way better and we got rid
of two warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Multi-line literal markups only work when they're idented at the
same level, with is not the case here:
Documentation/security/keys/core.rst:1597: WARNING: Inline literal start-string without end-string.
Documentation/security/keys/core.rst:1597: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1597: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1598: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1598: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1600: WARNING: Inline literal start-string without end-string.
Documentation/security/keys/core.rst:1600: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1600: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1600: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1600: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1666: WARNING: Inline literal start-string without end-string.
Documentation/security/keys/core.rst:1666: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1666: WARNING: Inline emphasis start-string without end-string.
Documentation/security/keys/core.rst:1666: WARNING: Inline emphasis start-string without end-string.
Fix it by using a code-block instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The code-block tag is at the wrong place, causing those
warnings:
Documentation/security/keys/trusted-encrypted.rst:112: WARNING: Literal block expected; none found.
Documentation/security/keys/trusted-encrypted.rst:121: WARNING: Unexpected indentation.
Documentation/security/keys/trusted-encrypted.rst:122: WARNING: Block quote ends without a blank line; unexpected unindent.
Documentation/security/keys/trusted-encrypted.rst:123: WARNING: Block quote ends without a blank line; unexpected unindent.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: James Morris <jamorris@linux.microsoft.com>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There's a wrong identation on a code block, and it tries to use
a reference that was not defined at the Italian translation.
Documentation/translations/it_IT/process/license-rules.rst:329: WARNING: Literal block expected; none found.
Documentation/translations/it_IT/process/license-rules.rst:332: WARNING: Unexpected indentation.
Documentation/translations/it_IT/process/license-rules.rst:339: WARNING: Block quote ends without a blank line; unexpected unindent.
Documentation/translations/it_IT/process/license-rules.rst:341: WARNING: Unexpected indentation.
Documentation/translations/it_IT/process/license-rules.rst:305: WARNING: Unknown target name: "metatags".
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Documentation/process/management-style.rst:35: WARNING: duplicate label decisions, other instance in Documentation/translations/zh_CN/process/management-style.rst
Documentation/process/programming-language.rst:37: WARNING: duplicate citation c-language, other instance in Documentation/translations/zh_CN/process/programming-language.rst
Documentation/process/programming-language.rst:38: WARNING: duplicate citation gcc, other instance in Documentation/translations/zh_CN/process/programming-language.rst
Documentation/process/programming-language.rst:39: WARNING: duplicate citation clang, other instance in Documentation/translations/zh_CN/process/programming-language.rst
Documentation/process/programming-language.rst:40: WARNING: duplicate citation icc, other instance in Documentation/translations/zh_CN/process/programming-language.rst
Documentation/process/programming-language.rst:41: WARNING: duplicate citation gcc-c-dialect-options, other instance in Documentation/translations/zh_CN/process/programming-language.rst
Documentation/process/programming-language.rst:42: WARNING: duplicate citation gnu-extensions, other instance in Documentation/translations/zh_CN/process/programming-language.rst
Documentation/process/programming-language.rst:43: WARNING: duplicate citation gcc-attribute-syntax, other instance in Documentation/translations/zh_CN/process/programming-language.rst
Documentation/process/programming-language.rst:44: WARNING: duplicate citation n2049, other instance in Documentation/translations/zh_CN/process/programming-language.rst
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Get rid of those warnings:
Documentation/virtual/kvm/amd-memory-encryption.rst:244: WARNING: Citation [white-paper] is not referenced.
Documentation/virtual/kvm/amd-memory-encryption.rst:246: WARNING: Citation [amd-apm] is not referenced.
Documentation/virtual/kvm/amd-memory-encryption.rst:247: WARNING: Citation [kvm-forum] is not referenced.
For references that aren't mentioned at the text by adding an
explicit reference to them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Sphinx doesn't like orphan documents:
Documentation/accelerators/ocxl.rst: WARNING: document isn't included in any toctree
Documentation/arm/stm32/overview.rst: WARNING: document isn't included in any toctree
Documentation/arm/stm32/stm32f429-overview.rst: WARNING: document isn't included in any toctree
Documentation/arm/stm32/stm32f746-overview.rst: WARNING: document isn't included in any toctree
Documentation/arm/stm32/stm32f769-overview.rst: WARNING: document isn't included in any toctree
Documentation/arm/stm32/stm32h743-overview.rst: WARNING: document isn't included in any toctree
Documentation/arm/stm32/stm32mp157-overview.rst: WARNING: document isn't included in any toctree
Documentation/gpu/msm-crash-dump.rst: WARNING: document isn't included in any toctree
Documentation/interconnect/interconnect.rst: WARNING: document isn't included in any toctree
Documentation/laptops/lg-laptop.rst: WARNING: document isn't included in any toctree
Documentation/powerpc/isa-versions.rst: WARNING: document isn't included in any toctree
Documentation/virtual/kvm/amd-memory-encryption.rst: WARNING: document isn't included in any toctree
Documentation/virtual/kvm/vcpu-requests.rst: WARNING: document isn't included in any toctree
So, while they aren't on any toctree, add :orphan: to them, in order
to silent this warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
When building it, it gets this warning:
Documentation/admin-guide/mm/numaperf.rst:168: WARNING: Footnote [1] is not referenced.
The problem is that this is not really a reference, as it is not
mentioned within the documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Changeset 5700d19748 ("docs: Get rid of the "basic profiling" guide")
removed an old basic-profiling.txt file that was not updated over
the last 11 years and won't reflect the post-perf era.
It makes no sense to keep its translation, so get rid of it too.
Fixes: 5700d19748 ("docs: Get rid of the "basic profiling" guide")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Alex Shi <alex.shi@linux.alibaba.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The cpuidle doc was split on two, one at the admin guide
and another one at the driver API guide. Instead of pointing
to a non-existent file, point to both (admin guide being
the first one).
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The patch adds k3 am654 compatible, specific properties and
an example.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Daniel Borkmann says:
====================
pull-request: bpf 2019-06-07
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix several bugs in riscv64 JIT code emission which forgot to clear high
32-bits for alu32 ops, from Björn and Luke with selftests covering all
relevant BPF alu ops from Björn and Jiong.
2) Two fixes for UDP BPF reuseport that avoid calling the program in case of
__udp6_lib_err and UDP GRO which broke reuseport_select_sock() assumption
that skb->data is pointing to transport header, from Martin.
3) Two fixes for BPF sockmap: a use-after-free from sleep in psock's backlog
workqueue, and a missing restore of sk_write_space when psock gets dropped,
from Jakub and John.
4) Fix unconnected UDP sendmsg hook API which is insufficient as-is since it
breaks standard applications like DNS if reverse NAT is not performed upon
receive, from Daniel.
5) Fix an out-of-bounds read in __bpf_skc_lookup which in case of AF_INET6
fails to verify that the length of the tuple is long enough, from Lorenz.
6) Fix libbpf's libbpf__probe_raw_btf to return an fd instead of 0/1 (for
{un,}successful probe) as that is expected to be propagated as an fd to
load_sk_storage_btf() and thus closing the wrong descriptor otherwise,
from Michal.
7) Fix bpftool's JSON output for the case when a lookup fails, from Krzesimir.
8) Minor misc fixes in docs, samples and selftests, from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.
This patch add the mcp25625 to the device tree bindings documentation.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With ReST, [foo]_ means a reference to foo, causing this warning:
Documentation/driver-api/gpio/driver.rst:419: WARNING: Unknown target name: "devm".
Fix it by using a literal for the name.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some new files got converted to yaml, but references weren't
updated accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the LM36274 LED specific bindings.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
After following the document step by step, the `cat trace` can't be
worked without enabling tracing_on and might mislead newbies about
the functionality.
Signed-off-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix a couple of s/poped/popped/ typos.
Signed-off-by: George G. Davis <george_davis@mentor.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In "Y+P" of this line, there are two non-ASCII characters(0xd9 0x8d)
following behind the 'Y'. Shown as a small '=' under the '+' in VIM
and a '賺' in webpage[1].
I think it's a mistake and remove these strange characters.
[1]: https://www.kernel.org/doc/Documentation/filesystems/xfs-delayed-logging-design.txt
Signed-off-by: Shiyang Ruan <ruansy.fnst@cn.fujitsu.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Documentation alignment for the following changes:
a700767a76 (doc/docs-next) docs: requirements.txt: recommend Sphinx 1.7.9
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix italian translation file references based on
`scripts/documentation-file-ref-check` output.
Signed-off-by: Federico Vaga <federico.vaga@vaga.pv.it>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The clk_foo_ops struct example has syntax errors. Fix it so it can be
copy-pasted and used more easily.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
While this doesn't make sense for production Kernels, in order to
avoid regressions when documents are touched, let's add a
check target at the make file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
All but one reference is capitalized. Fix the remaining one.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix typo in documentation file timekeeping.rst: CLOCK_MONONOTNIC_COARSE
should be CLOCK_MONOTONIC_COARSE.
Signed-off-by: Aurelien Thierry <aurelien.thierry@quoscient.io>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The example in the docs regarding multiple device-mappers is invalid (it
has a wrong number of arguments), it's a left over from previous
versions of the patch.
Replace the example with an valid and tested one.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The exported function name is dma_max_mapping_size(), not
dma_direct_max_mapping_size() so that this patch fixes
the function name in the documentation.
Fixes: 133d624b1c ("dma: Introduce dma_max_mapping_size()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The axienet driver requires the use of an axistream-connected attribute,
but this isn't documented in the devicetree bindings. Document how this
attribute is supposed to be used, including the upcoming change to make
the usage of this attribute optional.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio child node for the MDIO bus is generally required when using
this driver but was not documented other than being shown in the
example. Document it as an optional (but usually required) parameter.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously this driver only handled interrupts from the DMA RX and TX
blocks, not from the Ethernet core itself. Add optional support for
the Ethernet core interrupt, which is used to detect rx_missed and
framing errors signalled by the hardware. In order to use this
interrupt, a third interrupt needs to be specified in the device tree.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.
Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the "altr,socfpga-stmmac-a10-s10" binding for Arria10/Agilex/Stratix10
implementation of the stmmac ethernet controller.
On the Arria10, Agilex, and Stratix10 SoCs, there are a few differences from
the Cyclone5 and Arria5:
- The emac PHY setup bits are in separate registers.
- The PTP reference clock select mask is different.
- The register to enable the emac signal from FPGA is different.
Because of these differences, the dwmac-socfpga glue logic driver will
use this new binding to set the appropriate bits for PHY, PTP reference
clock, and signal from FPGA.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSQHSd0lITzzeNWNm3h3BK/laaZPAUCXPkV+wAKCRDh3BK/laaZ
PMGyAQDq6ry0bTRPIL52Ek+eRS/pi3bIsH96e22Q6W/NrAQEfwD+NtFZneAW/Tux
AuKIRWqS7UdqCjLurwMHfR9bOHrBDQI=
=z7pu
-----END PGP SIGNATURE-----
Merge tag 'ovl-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Here's one fix for a class of bugs triggered by syzcaller, and one
that makes xfstests fail less"
* tag 'ovl-fixes-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: doc: add non-standard corner cases
ovl: detect overlapping layers
ovl: support the FS_IOC_FS[SG]ETXATTR ioctls
Add the LM36274 backlight driver with regulator support.
This is a multi-function device for backlight applications.
Backlight properties will be documented in it's a supplemental
bindings document.
Regulator support is documented in the regulator/lm363x-regulator.txt
http://www.ti.com/lit/ds/symlink/lm36274.pdf
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Some times integer power functions, such as int_sqrt(), are needed, but
there is nothing about them in the generated documentation.
Fill the gap by adding a reference to the corresponding exported functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Some times string helpers are needed, but there is nothing about them
in the generated documentation.
Fill the gap by adding a reference to string_helpers.c exported functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Work from Tobin Harding:
Here is an updated version of the VFS doc conversion. This series
in no way represents a final point for the VFS documentation rather
it is a small step towards getting VFS docs updated. This series
does not update the content of vfs.txt, only does formatting.
Currently vfs.rst does not render well into HTML the method descriptions
for VFS data structures. We can improve the HTML output by putting the
description string on a new line following the method name.
Suggested-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
When RST packets are sent because no socket could be found,
it makes sense to use flowlabel_reflect sysctl to decide
if a reflection of the flowlabel is requested.
This extends commit 22b6722bfa ("ipv6: Add sysctl for per
namespace flow label reflection"), for some TCP RST packets.
In order to provide full control of this new feature,
flowlabel_reflect becomes a bitmask.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use hverkuil-cisco@xs4all.nl instead of hans.verkuil@cisco.com.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This changes v4l2_pix_format and v4l2_plane_pix_format sizeimage
field description to allow v4l clients to set bigger image size
in case of variable length compressed data.
Presently s5p-mfc and mtk-vcodec codec drivers use that. Lets
make it obvious in the documentation.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix minor typos in the DVB demux documentation.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The mv88e6250 has port_base_addr 0x8 or 0x18 (depending on
configuration pins), so it constitutes a new family and hence needs
its own compatible string.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible that TCP stack will decide to retransmit a packet
right when that packet's data gets acked, especially in presence
of packet reordering. This means that packets may be in flight,
even though tls_device code has already freed their record state.
Make fill_sg_in() and in turn tls_sw_fallback() not generate a
warning in that case, and quietly proceed to drop such frames.
Make the exit path from tls_sw_fallback() drop monitor friendly,
for users to be able to troubleshoot dropped retransmissions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for Device-Tree bindings for the
Socionext Synquacer spi driver.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
My previous fix miserably failed to catch all of the invocations of
"./scripts/sphinx-pre-install", so we got build errors. Try again with
more caffeine.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add binding document for the ethernet on MT7629 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add an extra required property "mediatek,physpeed" to sgmiisys to determine
link speed to match up the capability of the target PHY.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8df39e1687 ("media: dt-bindings: media: Add vendor prefix for
allegro") introduced a new devicetree binding vendors, however with an
improper syntax making the resulting YAML impossible to parse. Let's fix
this.
Fixes: 8df39e1687 ("media: dt-bindings: media: Add vendor prefix for allegro")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clarify that pure non-RMW usage of atomic_t is pointless, there is
nothing 'magical' about atomic_set() / atomic_read().
This is something that seems to confuse people, because I happen upon it
semi-regularly.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190524115231.GN2623@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
More words are added to lockdep design document regarding key concepts,
which should help people without lockdep experience read and understand
lockdep reports.
Signed-off-by: Yuyang Du <duyuyang@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bvanassche@acm.org
Cc: frederic@kernel.org
Cc: ming.lei@redhat.com
Cc: will.deacon@arm.com
Link: https://lkml.kernel.org/r/20190506081939.74287-3-duyuyang@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When isdn4linux came up in the context of another patch series, I
remembered that we had discussed removing it a while ago.
It turns out that the suggestion from Karsten Keil wa to remove I4L
in 2018 after the last public ISDN networks are shut down. This has
happened now (with a very small number of exceptions), so I guess it's
time to try again.
We currently have three ISDN stacks in the kernel: the original
isdn4linux (with the hisax driver), the newer CAPI (with four drivers),
and finally the mISDN stack (supporting roughly the same hardware as
hisax).
As far as I can tell, anyone using ISDN with mainline kernel drivers in
the past few years uses mISDN, and this is typically used for voice-only
PBX installations that don't require a public network.
The older stacks support additional features for data networks, but those
typically make no sense any more if there is no network to connect to.
My proposal for this time is to kill off isdn4linux entirely, as it seems
to have been unusable for quite a while. This code has been abandoned
for many years and it does cause problems for treewide maintenance as
it tends to do everything that we try to stop doing.
Birger Harzenetter mentioned that is is still using i4l in order to
make use of the 'divert' feature that is not part of mISDN, but has
otherwise moved on to mISDN for normal operation, like apparently
everyone else.
CAPI in turn is not quite as obsolete, but two of the drivers (avm
and hysdn) don't seem to be used at all, while another one (gigaset)
will stop being maintained as Paul Bolle is no longer able to
test it after the network gets shut down in September.
All three are now moved into drivers/staging to let others speak
up in case there are remaining users.
This leaves Bluetooth CMTP as the only remaining user of CAPI, but
Marcel Holtmann wishes to keep maintaining it.
For the discussion on version 1, see [2]
Unfortunately, Karsten Keil as the maintainer has not participated in
the discussion.
Arnd
[1] https://patchwork.kernel.org/patch/8484861/#17900371
[2] https://listserv.isdn4linux.de/pipermail/isdn4linux/2019-April/thread.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=1ISP
-----END PGP SIGNATURE-----
Merge tag 'isdn-removal' of https://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground
Arnd Bergmann says:
====================
isdn: deprecate non-mISDN drivers
When isdn4linux came up in the context of another patch series, I
remembered that we had discussed removing it a while ago.
It turns out that the suggestion from Karsten Keil wa to remove I4L
in 2018 after the last public ISDN networks are shut down. This has
happened now (with a very small number of exceptions), so I guess it's
time to try again.
We currently have three ISDN stacks in the kernel: the original
isdn4linux (with the hisax driver), the newer CAPI (with four drivers),
and finally the mISDN stack (supporting roughly the same hardware as
hisax).
As far as I can tell, anyone using ISDN with mainline kernel drivers in
the past few years uses mISDN, and this is typically used for voice-only
PBX installations that don't require a public network.
The older stacks support additional features for data networks, but those
typically make no sense any more if there is no network to connect to.
My proposal for this time is to kill off isdn4linux entirely, as it seems
to have been unusable for quite a while. This code has been abandoned
for many years and it does cause problems for treewide maintenance as
it tends to do everything that we try to stop doing.
Birger Harzenetter mentioned that is is still using i4l in order to
make use of the 'divert' feature that is not part of mISDN, but has
otherwise moved on to mISDN for normal operation, like apparently
everyone else.
CAPI in turn is not quite as obsolete, but two of the drivers (avm
and hysdn) don't seem to be used at all, while another one (gigaset)
will stop being maintained as Paul Bolle is no longer able to
test it after the network gets shut down in September.
All three are now moved into drivers/staging to let others speak
up in case there are remaining users.
This leaves Bluetooth CMTP as the only remaining user of CAPI, but
Marcel Holtmann wishes to keep maintaining it.
For the discussion on version 1, see [2]
Unfortunately, Karsten Keil as the maintainer has not participated in
the discussion.
Arnd
[1] https://patchwork.kernel.org/patch/8484861/#17900371
[2] https://listserv.isdn4linux.de/pipermail/isdn4linux/2019-April/thread.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
memory.stat and other files already consider subtrees in their output, and
we should too in order to not present an inconsistent interface.
The current situation is fairly confusing, because people interacting with
cgroups expect hierarchical behaviour in the vein of memory.stat,
cgroup.events, and other files. For example, this causes confusion when
debugging reclaim events under low, as currently these always read "0" at
non-leaf memcg nodes, which frequently causes people to misdiagnose breach
behaviour. The same confusion applies to other counters in this file when
debugging issues.
Aggregation is done at write time instead of at read-time since these
counters aren't hot (unlike memory.stat which is per-page, so it does it
at read time), and it makes sense to bundle this with the file
notifications.
After this patch, events are propagated up the hierarchy:
[root@ktst ~]# cat /sys/fs/cgroup/system.slice/memory.events
low 0
high 0
max 0
oom 0
oom_kill 0
[root@ktst ~]# systemd-run -p MemoryMax=1 true
Running as unit: run-r251162a189fb4562b9dabfdc9b0422f5.service
[root@ktst ~]# cat /sys/fs/cgroup/system.slice/memory.events
low 0
high 0
max 7
oom 1
oom_kill 1
As this is a change in behaviour, this can be reverted to the old
behaviour by mounting with the `memory_localevents' flag set. However, we
use the new behaviour by default as there's a lack of evidence that there
are any current users of memory.events that would find this change
undesirable.
akpm: this is a behaviour change, so Cc:stable. THis is so that
forthcoming distros which use cgroup v2 are more likely to pick up the
revised behaviour.
Link: http://lkml.kernel.org/r/20190208224419.GA24772@chrisdown.name
Signed-off-by: Chris Down <chris@chrisdown.name>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix Sphinx warnings in Documentation/vm/hmm.rst by using "::" notation and
inserting a blank line. Also add a missing ';'.
Documentation/vm/hmm.rst:292: WARNING: Unexpected indentation.
Documentation/vm/hmm.rst:300: WARNING: Unexpected indentation.
Link: http://lkml.kernel.org/r/c5995359-7c82-4e47-c7be-b58a4dda0953@infradead.org
Fixes: 023a019a9b ("mm/hmm: add default fault flags to avoid the need to pre-fill pfns arrays")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-05-31
The following pull-request contains BPF updates for your *net-next* tree.
Lots of exciting new features in the first PR of this developement cycle!
The main changes are:
1) misc verifier improvements, from Alexei.
2) bpftool can now convert btf to valid C, from Andrii.
3) verifier can insert explicit ZEXT insn when requested by 32-bit JITs.
This feature greatly improves BPF speed on 32-bit architectures. From Jiong.
4) cgroups will now auto-detach bpf programs. This fixes issue of thousands
bpf programs got stuck in dying cgroups. From Roman.
5) new bpf_send_signal() helper, from Yonghong.
6) cgroup inet skb programs can signal CN to the stack, from Lawrence.
7) miscellaneous cleanups, from many developers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There has been quite a few progress around the two steps mentioned in the
answer to the following question:
Q: BPF 32-bit subregister requirements
This patch updates the answer to reflect what has been done.
v2:
- Add missing full stop. (Song Liu)
- Minor tweak on one sentence. (Song Liu)
v1:
- Integrated rephrase from Quentin and Jakub
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
cgroup already uses floating point for percent[ile] numbers and there
are several controllers which want to take them as input. Add a
generic parse helper to handle inputs.
Update the interface convention documentation about the use of
percentage numbers. While at it, also clarify the default time unit.
Signed-off-by: Tejun Heo <tj@kernel.org>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent makefile changes included an invocation of
./scripts/sphinx-pre-install. Unfortunately, that fails when a separate
build directory is in use with:
/bin/bash: ./scripts/sphinx-pre-install: No such file or directory
Use $(srctree) to fully specify the location of this script.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Here are some tiny USB fixes for a number of reported issues for
5.2-rc3.
Nothing huge here, just a small collection of xhci and other driver bugs
that syzbot has been finding in some drivers. There is also a usbip fix
and a fix for the usbip fix in here :)
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCDwQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yli6QCaAmaLPqpgO12vsYlD7KYfktM7wYEAnjD+L73Z
Sc9htZ4BudpBzjK3FPyH
=rCpe
-----END PGP SIGNATURE-----
Merge tag 'usb-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some tiny USB fixes for a number of reported issues for
5.2-rc3.
Nothing huge here, just a small collection of xhci and other driver
bugs that syzbot has been finding in some drivers. There is also a
usbip fix and a fix for the usbip fix in here :)
All have been in linux-next with no reported issues"
* tag 'usb-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usbip: usbip_host: fix stub_dev lock context imbalance regression
media: smsusb: better handle optional alignment
xhci: Use %zu for printing size_t type
xhci: Convert xhci_handshake() to use readl_poll_timeout_atomic()
xhci: Fix immediate data transfer if buffer is already DMA mapped
usb: xhci: avoid null pointer deref when bos field is NULL
usb: xhci: Fix a potential null pointer dereference in xhci_debugfs_create_endpoint()
xhci: update bounce buffer with correct sg num
media: usb: siano: Fix false-positive "uninitialized variable" warning
USB: rio500: update Documentation
USB: rio500: simplify locking
USB: rio500: fix memory leak in close after disconnect
USB: rio500: refuse more than one device at a time
usbip: usbip_host: fix BUG: sleeping function called from invalid context
USB: sisusbvga: fix oops in error path of sisusb_probe
USB: Add LPM quirk for Surface Dock GigE adapter
media: usb: siano: Fix general protection fault in smsusb
usb: mtu3: fix up undefined reference to usb_debug_root
USB: Fix slab-out-of-bounds write in usb_get_bos_descriptor
With all isdn4linux hardware drivers gone, this is only a wrapper around
CAPI to support old user space. However, from looking at the mailing
list, it seems that the last time anyone asked about it was in 2014,
when the upgrade from a linux-2.4 installation failed, and mISDN was
suggested as a replacement.
The largest public ISDN network (Deutsche Telekom) was supposed to be
shut down 2018, which must have drastically reduced the number of legacy
installations.
When we last discussed removing i4l in 2016, Karsten Keil suggested
revisiting this in 2018. I guess this is overdue.
Link: http://listserv.isdn4linux.de/pipermail/isdn4linux/2014-October/006165.html
Link: https://patchwork.kernel.org/patch/8484861/#17900371
Link: https://listserv.isdn4linux.de/pipermail/isdn4linux/2019-April/thread.html
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the decline of ISDN, this seems to have become almost completely
obsolete, and even in the past years before that, almost all remaining
users appear to have used mISDN instead.
Birger Harzenetter noted that he is still using i4l/hisax to take
advantage of the 'divert' driver for call diversion, but otherwise uses
mISDN on the same hardware. This is a rare edge case as far as I
can tell, but we are still breaking an actively used work flow
(see https://xkcd.com/1172/).
We debated moving i4l/hisax to staging as an intermediate step, but as
he is not likely to change the setup, and that would just delay breaking
this use case. The alternatives here are to stay on stable kernels
< 5.2, to create an external driver repository for isdn4linux, or to
add divert functionality to mISDN.
Cc: Birger Harzenetter <WIMPy@yeti.dk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
isdn4linux is getting removed, and the gigaset driver can still
use the CAPI support, so this can all go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull networking fixes from David Miller:
1) Fix OOPS during nf_tables rule dump, from Florian Westphal.
2) Use after free in ip_vs_in, from Yue Haibing.
3) Fix various kTLS bugs (NULL deref during device removal resync,
netdev notification ignoring, etc.) From Jakub Kicinski.
4) Fix ipv6 redirects with VRF, from David Ahern.
5) Memory leak fix in igmpv3_del_delrec(), from Eric Dumazet.
6) Missing memory allocation failure check in ip6_ra_control(), from
Gen Zhang. And likewise fix ip_ra_control().
7) TX clean budget logic error in aquantia, from Igor Russkikh.
8) SKB leak in llc_build_and_send_ui_pkt(), from Eric Dumazet.
9) Double frees in mlx5, from Parav Pandit.
10) Fix lost MAC address in r8169 during PCI D3, from Heiner Kallweit.
11) Fix botched register access in mvpp2, from Antoine Tenart.
12) Use after free in napi_gro_frags(), from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (89 commits)
net: correct zerocopy refcnt with udp MSG_MORE
ethtool: Check for vlan etype or vlan tci when parsing flow_rule
net: don't clear sock->sk early to avoid trouble in strparser
net-gro: fix use-after-free read in napi_gro_frags()
net: dsa: tag_8021q: Create a stable binary format
net: dsa: tag_8021q: Change order of rx_vid setup
net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue value
ipv4: tcp_input: fix stack out of bounds when parsing TCP options.
mlxsw: spectrum: Prevent force of 56G
mlxsw: spectrum_acl: Avoid warning after identical rules insertion
net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT
r8169: fix MAC address being lost in PCI D3
net: core: support XDP generic on stacked devices.
netvsc: unshare skb in VF rx handler
udp: Avoid post-GRO UDP checksum recalculation
net: phy: dp83867: Set up RGMII TX delay
net: phy: dp83867: do not call config_init twice
net: phy: dp83867: increase SGMII autoneg timer duration
net: phy: dp83867: fix speed 10 in sgmii mode
net: phy: marvell10g: report if the PHY fails to boot firmware
...
Add a keyctl to atomically move a link to a key from one keyring to
another. The key must exist in "from" keyring and a flag can be given to
cause the operation to fail if there's a matching key already in the "to"
keyring.
This can be done with:
keyctl(KEYCTL_MOVE,
key_serial_t key,
key_serial_t from_keyring,
key_serial_t to_keyring,
unsigned int flags);
The key being moved must grant Link permission and both keyrings must grant
Write permission.
flags should be 0 or KEYCTL_MOVE_EXCL, with the latter preventing
displacement of a matching key from the "to" keyring.
Signed-off-by: David Howells <dhowells@redhat.com>
Add another example to clarify that HugePages smaller than 1MB will
be displayed using "KB", with an uppercased K (eg. 20KB), and not the
normal SI prefix kilo (small k).
Because of a misunderstanding/copy-paste error inside runc
(see https://github.com/opencontainers/runc/pull/2065), it tried
accessing the cgroup control file of a 64kB HugePage using
"hugetlb.64kB._____" instead of the correct "hugetlb.64KB._____".
Adding a new example will make it clear how sizes smaller than 1MB are
handled.
Signed-off-by: Odin Ugedal <odin@ugedal.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add docs for /proc/sys/net/ipv4/tcp_fastopen_key
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Cc: Jeremy Sowden <jeremy@azazel.net>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed at the linux-doc ML, while we'll still support
version 1.3, it is time to recommend a more modern version.
So, let's switch the minimal requirements to Sphinx 1.7.9,
as it has the "-jauto" flag, with makes a lot faster when
building documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Since Sphinx version 1.7, it is possible to use "-jauto" in
order to speedup documentation builds. On older versions,
while -j was already supported, one would need to set the
number of threads manually.
So, if SPHINXOPTS is not provided, add -jauto, in order to
speed up the build. That makes it *a lot* times faster than
without -j.
If one really wants to slow things down, it can just use:
make SPHINXOPTS=-j1 htmldocs
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
[ jc: fixed perl magic to determine sphinx version ]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Call the script every time a make docs target is selected, on
a simplified check mode.
With this change, the script will set two vars:
$min_version - obtained from `needs_sphinx` var inside
conf.py (currently, '1.3')
$rec_version - obtained from sphinx/requirements.txt.
With those changes, a target like "make htmldocs" will do:
1) If no sphinx-build/sphinx-build3 is found, it will run
the script on normal mode as before, checking for all
system dependencies and providing install hints for the
needed programs and will abort the build;
2) If no sphinx-build/sphinx-build3 is found, but there is
a sphinx_${VER}/bin/activate file, and if
${VER} >= $min_version (string comparation), it will
run in full mode, and will recommend to activate the
virtualenv. If there are multiple virtualenvs, it
will string sort the versions, recommending the
highest version and will abort the build;
3) If Sphinx is detected but has a version lower than
$min_version, it will run in full mode - with will
recommend creating a virtual env using sphinx/requirements.txt,
and will abort the build.
4) If Sphinx is detected and version is lower than
$rec_version, it will run in full mode and will
recommend creating a virtual env using sphinx/requirements.txt.
In this case, it **won't** abort the build.
5) If Sphinx is detected and version is equal or righer than
$rec_version it will return just after detecting the
version ("quick mode"), not checking if are there any
missing dependencies.
Just like before, if one wants to install Sphinx from the
distro, it has to call the script manually and use `--no-virtualenv`
argument to get the hints for his OS:
You should run:
sudo dnf install -y python3-sphinx python3-sphinx_rtd_theme
While here, add a small help for the three optional arguments
for the script.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Move the binding for the discrete Atmel I2C Elliptic Curve h/w crypto
module to trivial-devices.yaml, as it doesn't belong in atmel-crypto
which describes unrelated on-SoC peripherals.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a compatible string for the Atmel SHA204A I2C crypto processor.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the unnecessary constant CRYPTO_ALG_TYPE_DIGEST, which has the
same value as CRYPTO_ALG_TYPE_HASH.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export a phy_standalone device attribute that is meant to give the
indication that this PHY lacks an attached_dev and its corresponding
sysfs link. The attribute will be created only when the
phy_attach_direct() function will be called with a NULL net_device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vfs.txt is currently stale. If we convert it to RST this is a good
first step in the process of getting the VFS documentation up to date.
This patch does the following (all as a single patch so as not to
introduce any new SPHINX build warnings)
- Use '.. code-block:: c' for C code blocks and indent the code blocks.
- Use double backticks for struct member descriptions.
- Fix a couple of build warnings by guarding pointers (*) with double
backticks .e.g ``*ptr``.
- Add vfs to Documentation/filesystems/index.rst
The member descriptions paragraph indentation was not touched. It is
not pretty but these do not cause build warnings. These descriptions
all need updating anyways so leave it as it is for now.
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There are bunch of places with 8 spaces, in preparation for correctly
indenting all code snippets (during conversion to RST) change these to
use tabspaces.
This patch is whitespace only.
Convert instances of 8 consecutive spaces to a single tabspace.
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Currently file pre-amble contains custom indentation. RST is not going
to like this, lets left-align the text. Put the copyright notices in a
list in preparation for converting document to RST.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Currently the licence is indicated via a custom string. We have SPDX
license identifiers now for this task.
Use SPDX license identifier matching current license string.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Kernel RST has a preferred heading adornment scheme. Currently all the
heading adornments follow this scheme except the document heading.
Use correct heading adornment for initial heading.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Currently spacing before and after headings is non-uniform. Use two
blank lines before a heading and one after the heading.
Use uniform spacing around headings.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In preparation for conversion to RST format use the kernels favoured
documentation column width. If we are going to do this we might as well
do it thoroughly. Just do the paragraphs (not the indented stuff), the
rest will be done during indentation fix up patch.
This patch is whitespace only, no textual changes.
Use 72 character column width for all paragraph sections.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Currently sometimes document has a single space after a period and
sometimes it has double. Whichever we use it should be uniform.
Use double space after period, be uniform.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Currently the file has a bunch of spaces before tabspaces. This is a
nuisance when patching the file because they show up whenever we touch
these lines. Let's just fix them all now in preparation for doing the
RST conversion.
Remove spaces before tabspaces.
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The default behavior of hardlockup depends on the config of
CONFIG_BOOTPARAM_HARDLOCKUP_PANIC.
Fix the description of nmi_watchdog to make it clear.
Suggested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kees Cook <keescook@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch fixes some spelling typos in histogram.rst
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There's a new warning about a deprecation function. Add a
logic at cdomain.py to avoid that.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
our extensions and, thus, the documentation build in general. Who knew
that those deprecation warnings it was outputting actually meant we should
change something? This set of fixes makes the build work again with
Sphinx 2.0 and eliminates the warnings for 1.8. As part of that, we also
need a few fixes to the docs for places where the new Sphinx is more
strict.
It is a bit late in the cycle for this kind of change, but it does fix
problems that people are experiencing now.
There has been some talk of raising the minimum version of Sphinx we
support. I don't want to do that abruptly, though, so these changes add
some glue to continue to support versions back to 1.3. We will be adding
some infrastructure soon to nudge users of old versions forward, with the
idea of maybe increasing our minimum version (and removing this glue)
sometime in the future.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlzsYw8PHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5YGuwH+gOk2lGPpI7tsIsctUr3TTviYbu9EywGINUA
c2pPQBHbC13F/QKkb/WArnIhM7eRMWxNy1IlrzqTTLRcAteJihoRNldLVpImxwHJ
DaULovUHRO9uNuVORGV4RLOBUUkrguoz4X7OZooT3tluRZcL58C3Qn8MbZYiZYf1
ZJKHVJxfSedyHYTK1H5qB9uAAvdoNGLjvK8pzA9S7HgHM9viuOlY2GTHn4uvlmI+
qgnbVRNeEb8IRFztvKy2RyMAisx2o5v/lfpKVM+OC9EJgkpw+mw55YUdfDeNavJg
2d3xv8zgS1TP+qAmba2uVwiRDNChTKxz72nbaqZZGOt16StRiyY=
=hrKI
-----END PGP SIGNATURE-----
Merge tag 'docs-5.2-fixes2' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"The Sphinx 2.0 release contained a few incompatible API changes that
broke our extensions and, thus, the documentation build in general.
Who knew that those deprecation warnings it was outputting actually
meant we should change something? This set of fixes makes the build
work again with Sphinx 2.0 and eliminates the warnings for 1.8. As
part of that, we also need a few fixes to the docs for places where
the new Sphinx is more strict.
It is a bit late in the cycle for this kind of change, but it does fix
problems that people are experiencing now.
There has been some talk of raising the minimum version of Sphinx we
support. I don't want to do that abruptly, though, so these changes
add some glue to continue to support versions back to 1.3. We will be
adding some infrastructure soon to nudge users of old versions
forward, with the idea of maybe increasing our minimum version (and
removing this glue) sometime in the future"
* tag 'docs-5.2-fixes2' of git://git.lwn.net/linux:
drm/i915: Maintain consistent documentation subsection ordering
scripts/sphinx-pre-install: make it handle Sphinx versions
docs: Fix conf.py for Sphinx 2.0
docs: fix multiple doc build warnings in enumeration.rst
lib/list_sort: fix kerneldoc build error
docs: fix numaperf.rst and add it to the doc tree
doc: Cope with the deprecation of AutoReporter
doc: Cope with Sphinx logging deprecations
The A83T SoC has a camera sensor interface (known as CSI in Allwinner
lingo), which is similar to the one found on the A64 and H3. The only
difference seems to be that support of MIPI CSI through a connected
MIPI CSI-2 bridge.
Add a compatible string for this variant.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The reserved field array for struct media_link_desc has length 2, not 4.
And the reserved field array of struct media_links_enum was never documented
at all.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add vendor prefix for Allegro DVT, a provider of H.264/AVC, H.265/HEVC,
AVS2, VP9 and AV1 compliance test suites and H.264/AVC, H.265/HEVC, and
VP9 encoder, codec and decoder hardware (RTL) IPs.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add device-tree bindings for the Allegro DVT video IP core found on the
Xilinx ZynqMP EV family.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The H264_SLICE_RAW format introduced before is meant for stateless
decoders that will need the H264 parsed slice data without the start code.
Let's document it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Stateless video codecs will require both the H264 metadata and slices in
order to be able to decode frames.
This introduces the definitions for the structures used to pass the
metadata from the userspace to the kernel.
[hverkuil-cisco@xs4all.nl: add space after . in ".For"]
[hverkuil-cisco@xs4all.nl: sync v4l2_ctrl_h264_decode_params struct layout with header]
Co-developed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add MPEG-2 CID definitions for profiles and levels defined in ITU-T Rec.
H.262.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add DT bindings for the Renesas RZ/A1 Interrupt Controller.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Both sysfs-bus-mdio and sysfs-class-net-phydev contain the same
duplication information. There is not currently any MDIO bus specific
attribute, but there are PHY device (struct phy_device) specific
attributes. Use the more precise description from sysfs-bus-mdio and
carry that over to sysfs-class-net-phydev.
Fixes: 86f22d04df ("net: sysfs: Document PHY device sysfs attributes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a paragraph to make it more clear that video equipment will transmit
fields in the same order the fields were captured, and replace some of
the "is transmitted first" language with "is the older field", since the
latter is the important info for motion compensation applications.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A positive value of rcupdate.rcu_task_stall_timeout is an interval
in seconds rather than jiffies.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Document similar real world examples in the kernel corresponding to the
second and third code snippets. Also correct an issue in
release_referenced() in the code snippet example.
Cc: oleg@redhat.com
Cc: jannh@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
[ paulmck: Do a bit of wordsmithing. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzrJgUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1XAIAJajJpeKc9MVQipi
zWiI+WgHDg8gG/HnLKzP2Zp4MUjTCz30t0rnBbdo6AyK6LnPBL53yxg9q64XN7vI
p/h2ys+/DvqhIYSPWX6C++HYQT4Cb5ghxJABEIsztd3G4nfB9L2vgq9zKSNFusTD
UtfUxufciZPX515TuE4IqWMwS4Ut5daH7V3jjZunhPiayTFv64e1KbpKLLzHR0NR
DfFbrPcdp7VyCT/A5AKrqfqeB6O9dm/Fe4CsdsaKuzASCXJ6GUc/A7iZDndv/KA4
f5Xh7SGlQ2TfT1ud/aMfdw3AcMjqB8zgMJenovJ7UuHDfULBWNeAmMh/cTDwY9eY
Xgyvfm0=
=S8p9
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc2' into patchwork
Merge back from upstream into media tree, as there are some
patches merged upstream that has pontential of causing
conflicts (one actually rised a conflict already).
Linux 5.2-rc2
* tag 'v5.2-rc2': (377 commits)
Linux 5.2-rc2
random: fix soft lockup when trying to read from an uninitialized blocking pool
tracing: Silence GCC 9 array bounds warning
ext4: fix dcache lookup of !casefolded directories
locking/lock_events: Use this_cpu_add() when necessary
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
...
The A83t and compatibles controllers don't have any reception capabilities
on some instances of the controllers, even though it was never documented
as such in the binding before.
Therefore, on those controllers, we don't have the option to set an RX DMA
channel.
This was already done in the DTSI, but the binding itself was never
updated. Let's add a special case in the schemas.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Allwinner SoCs feature an I2S controller across multiple SoC
generations.
However, earlier generations were a bit simpler than the subsequent ones,
and for example would always have RX and TX capabilities, and no reset
lines.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner H6 has a SPDIF controller with an increase of the fifo
size and a sligher difference in memory mapping compare to H3/A64.
This make it not compatible with the previous generation.
Introduce a specific bindings for H6 SoC.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the Arm PL061 GPIO controller binding to json-schema format.
As I'm the author for all but the gpio-ranges line, make the schema dual
GPL/BSD license.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'default (active high)' lines are repeated twice. Avoid people stare at
their screens looking for differences.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Because this patch series dropped support for 10 bit I2C devices, I'm
documenting this.
Signed-off-by: Przemyslaw Gaj <pgaj@cadence.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Add binding documentation for Atheros/QCA networking IP core used
in many routers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some workloads need to change kthread priority for RCU core processing
without affecting other softirq work. This commit therefore introduces
the rcutree.use_softirq kernel boot parameter, which moves the RCU core
work from softirq to a per-CPU SCHED_OTHER kthread named rcuc. Use of
SCHED_OTHER approach avoids the scalability problems that appeared
with the earlier attempt to move RCU core processing to from softirq
to kthreads. That said, kernels built with RCU_BOOST=y will run the
rcuc kthreads at the RCU-boosting priority.
Note that rcutree.use_softirq=0 must be specified to move RCU core
processing to the rcuc kthreads: rcutree.use_softirq=1 is the default.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[ paulmck: Adjust for invoke_rcu_callbacks() only ever being invoked
from RCU core processing, in contrast to softirq->rcuc transition
in old mainline RCU priority boosting. ]
[ paulmck: Avoid wakeups when scheduler might have invoked rcu_read_unlock()
while holding rq or pi locks, also possibly fixing a pre-existing latent
bug involving raise_softirq()-induced wakeups. ]
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
- Update checkpatch.pl to use DT vendor-prefixes.yaml
- Fix DT binding references to files converted to DT schema
- Clean-up Arm CPU binding examples to match schema
- Add Sifive block versioning scheme documentation
- Pass binding directory base to validation tools for reference lookups
-----BEGIN PGP SIGNATURE-----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=7oNi
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
- Update checkpatch.pl to use DT vendor-prefixes.yaml
- Fix DT binding references to files converted to DT schema
- Clean-up Arm CPU binding examples to match schema
- Add Sifive block versioning scheme documentation
- Pass binding directory base to validation tools for reference lookups
* tag 'devicetree-fixes-for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
checkpatch.pl: Update DT vendor prefix check
dt: bindings: mtd: replace references to nand.txt with nand-controller.yaml
dt-bindings: interrupt-controller: arm,gic: Fix schema errors in example
dt-bindings: arm: Clean up CPU binding examples
dt: fix refs that were renamed to json with the same file name
dt-bindings: Pass binding directory to validation tools
dt-bindings: sifive: describe sifive-blocks versioning
Documentation/driver-api/target.rst is seeking kerneldoc comments in
drivers/target/target_core_device.c, but no such comments exist. Take out
the kernel-doc directive and eliminate one warning from the build.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The LM3697 is a single function LED driver. The single function LED
driver needs to reside in the LED directory as a dedicated LED driver
and not as a MFD device. The device does have common brightness and ramp
features and those can be accomodated by a TI LMU framework.
The LM3697 dt binding needs to be moved from the ti-lmu.txt and a dedicated
LED dt binding needs to be added. The new LM3697 LED dt binding will then
reside in the Documentation/devicetree/bindings/leds directory and follow the
current LED and general bindings guidelines.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Add new interface mode USXGMII to binding documentation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stratix10 service layer documentation tried to include a kerneldoc
comments for a nonexistent struct; leading to a "no structured comments
found" message. Switch it to stratix10_svc_command_config_type, which
appears at that spot in the sequence and was not included.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch adds the binding documentation for a simple SPI based LED
controller which use only one byte for setting the brightness.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
- Fix incorrect LDADD instruction encoding in our disassembly macros
- Disable the broken ARM64_PSEUDO_NMI support for now
- Add workaround for Cortex-A76 CPU erratum #1463225
- Handle Cortex-A76/Neoverse-N1 erratum #1418040 w/ existing workaround
- Fix IORT build failure if IOMMU_SUPPORT=n
- Fix place-relative module relocation range checking and its
interaction with KASLR
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzoC8MACgkQt6xw3ITB
YzQfiAf+MXFzrAd3o7v40CnZu6ELw+ldedPh34oBjD7h6we3hroxi5Fss2nbwH0o
BmAm4Nv1/Njk5+hA7Mlp3/mRn0vcd3NDP+FyH3inLjUU7owc41thp0SKlCOfFdZk
K8sVCOeCWt7GEEPcnFsPO0nU+7f3ZKDDNBo0L+qJPxrMOTDcbQ3cIjW/ua7vQRHv
pIDGF+iJAhHeNoc1Wjq08F8Q+Dq7dYvhtokeyDivSn4NulmRvdL+z581gMmj7ExT
ARB6WtHGoOo+8UdjBJIDnXRKhJLfGexQaoAojk+IogaV0ACDtz6CuqsSIh1e5SFC
oPqRSP5ITTbXEDS5uaUW1pYlwmGTaw==
=ynUz
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 fixes from Will Deacon:
- Fix incorrect LDADD instruction encoding in our disassembly macros
- Disable the broken ARM64_PSEUDO_NMI support for now
- Add workaround for Cortex-A76 CPU erratum #1463225
- Handle Cortex-A76/Neoverse-N1 erratum #1418040 w/ existing workaround
- Fix IORT build failure if IOMMU_SUPPORT=n
- Fix place-relative module relocation range checking and its
interaction with KASLR
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: insn: Add BUILD_BUG_ON() for invalid masks
arm64: insn: Fix ldadd instruction encoding
arm64: Kconfig: Make ARM64_PSEUDO_NMI depend on BROKEN for now
arm64: Handle erratum 1418040 as a superset of erratum 1188873
arm64/module: deal with ambiguity in PRELxx relocation ranges
ACPI/IORT: Fix build error when IOMMU_SUPPORT is disabled
arm64/kernel: kaslr: reduce module randomization range to 2 GB
arm64: errata: Add workaround for Cortex-A76 erratum #1463225
arm64: Remove useless message during oops
Our version check in Documentation/conf.py never envisioned a world where
Sphinx moved beyond 1.x. Now that the unthinkable has happened, fix our
version check to handle higher version numbers correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The conversion of acpi/enumeration.txt to RST included one markup error,
leading to many warnings like:
.../firmware-guide/acpi/enumeration.rst:430: WARNING: Unexpected indentation.
Add the missing colon and create some peace.
Fixes: c24bc66e81 ("Documentation: ACPI: move enumeration.txt to firmware-guide/acpi and convert to reST")
Cc: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Commit 13bac55ef7 ("doc/mm: New documentation for memory performance")
added numaperf.rst, but did not add it to the TOC tree. There was also an
incorrectly marked literal block leading to this warning sequence:
numaperf.rst:24: WARNING: Unexpected indentation.
numaperf.rst:24: WARNING: Inline substitution_reference start-string without end-string.
numaperf.rst:25: WARNING: Block quote ends without a blank line; unexpected unindent.
Fix the block and add the file to the document tree.
Fixes: 13bac55ef7 ("doc/mm: New documentation for memory performance")
Cc: Keith Busch <keith.busch@intel.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
AutoReporter is going away; recent versions of sphinx emit a warning like:
Documentation/sphinx/kerneldoc.py:125:
RemovedInSphinx20Warning: AutodocReporter is now deprecated.
Use sphinx.util.docutils.switch_source_input() instead.
Make the switch. But switch_source_input() only showed up in 1.7, so we
have to do ugly version checks to keep things working in older versions.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Recent versions of sphinx will emit messages like:
Documentation/sphinx/kerneldoc.py:103:
RemovedInSphinx20Warning: app.warning() is now deprecated.
Use sphinx.util.logging instead.
Switch to sphinx.util.logging to make this unsightly message go away.
Alas, that interface was only added in version 1.6, so we have to add a
version check to keep things working with older sphinxes.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
spdxcheck.py script up with the current state of affairs.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAlzmskAPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yc2YIAIakPFL8HH9HAPiuhrQnL78vU06pRwqk19sc
ovEtwWBr6gxLcqa4oL0opatElmUmoYvRN0ZaPdYZRgCWZSpUAzzNVJgMDPjeDbIK
aE8vfN8DzqHtT3MDNrLAlP2zK9s3srE1GovnmJgtScSOE5bS3cQumeM8qhoz6zWG
p8tDyB9LxUaZb3RiEGukgYqciNwoy3e/V/5lkfCm7Yv6gByzyQLVov79N9XsLB5g
Is8skZEfdNqjFYNPOAyPN2lFTCSzyT1Wkl2GwvZ3EPZCNHLlnj2NpyfZuGjMFaMK
zyM0vypPPrN8Qnubd3vWPw0r0gNW4nCcfZRelkjRR9+TYGGEGus=
=gh2E
-----END PGP SIGNATURE-----
Merge tag 'docs-5.2-fixes' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of fixes for a docs build problem, along with catching the
spdxcheck.py script up with the current state of affairs"
* tag 'docs-5.2-fixes' of git://git.lwn.net/linux:
Documentation: kdump: fix minor typo
scripts/spdxcheck.py: Add dual license subdirectory
scripts/spdxcheck.py: Fix path to deprecated licenses
counter: fix Documentation build error due to incorrect source file name
We already mitigate erratum 1188873 affecting Cortex-A76 and
Neoverse-N1 r0p0 to r2p0. It turns out that revisions r0p0 to
r3p1 of the same cores are affected by erratum 1418040, which
has the same workaround as 1188873.
Let's expand the range of affected revisions to match 1418040,
and repaint all occurences of 1188873 to 1418040. Whilst we're
there, do a bit of reformating in silicon-errata.txt and drop
a now unnecessary dependency on ARM_ARCH_TIMER_OOL_WORKAROUND.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Convert the Arm pl022 binding to DT schema format. The clock binding was
missing, so it is added to the schema. It really should be required as
well, but there are some platforms (spear) not yet using DT clock
binding.
Cc: Mark Brown <broonie@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-spi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Revisions of the Cortex-A76 CPU prior to r4p0 are affected by an erratum
that can prevent interrupts from being taken when single-stepping.
This patch implements a software workaround to prevent userspace from
effectively being able to disable interrupts.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Document which capability is required, rather than just saying
that "root permissions" are required.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document this new cec_msg flag.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Create CPU topology sysfs attributes: "core_cpus" and "core_cpus_list"
These attributes represent all of the logical CPUs that share the
same core.
These attriutes is synonymous with the existing "thread_siblings" and
"thread_siblings_list" attribute, which will be deprecated.
Create CPU topology sysfs attributes: "die_cpus" and "die_cpus_list".
These attributes represent all of the logical CPUs that share the
same die.
Suggested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/071c23a298cd27ede6ed0b6460cae190d193364f.1557769318.git.len.brown@intel.com
The existing sysfs cpu/topology/core_siblings (and core_siblings_list)
attributes are documented, implemented, and used by programs to represent
set of logical CPUs sharing the same package.
This makes sense if the next topology level above a core is always a
package. But on systems where there is a die topology level between a core
and a package, the name and its definition become inconsistent.
So without changing its function, add a name for this map that describes
what it actually is -- package CPUs -- the set of CPUs that share the same
package.
This new name will be immune to changes in topology, since it describes
threads at the current level, not siblings at a contained level.
Suggested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/d9d3228b82fb5665e6f93a0ccd033fe022558521.1557769318.git.len.brown@intel.com
Some new systems have multiple software-visible die within each package.
Update Linux parsing of the Intel CPUID "Extended Topology Leaf" to handle
either CPUID.B, or the new CPUID.1F.
Add cpuinfo_x86.die_id and cpuinfo_x86.max_dies to store the result.
die_id will be non-zero only for multi-die/package systems.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux-doc@vger.kernel.org
Link: https://lkml.kernel.org/r/7b23d2d26d717b8e14ba137c94b70943f1ae4b5c.1557769318.git.len.brown@intel.com
The clock output is generally only used for testing and development and
not used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a note to make it more clear how the driver behaves when "rgmii" vs
"rgmii-id", "rgmii-idrx", or "rgmii-idtx" interface modes are selected.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe existing kernel TLS offload (added back in Linux 4.19) -
the mechanism, the expected behavior and the notable corner cases.
This documentation is mostly targeting hardware vendors who want
to implement offload, to ensure consistency between implementations.
v2:
- add emphasis around TLS_SW/TLS_HW/TLS_HW_RECORD;
- remove mentions of ongoing work (Boris);
- split the flow of data in SW vs. HW cases in TX overview
(Boris);
- call out which fields are updated by the device and which
are filled by the stack (Boris);
- move error handling into it's own section (Boris);
- add more words about fallback (Boris);
- note that checksum validation is required (Alexei);
- note that drivers shouldn't pay attention to the TLS
device features.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the TLS doc to RST. Use C code blocks for the code
samples, and mark hyperlinks.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the device drivers have really long document titles
making the networking table of contents hard to look through.
Place vendor drivers under a submenu.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
nand-controller.yaml replaced nand.txt however the references to it were
not updated. This change updates these references wherever it appears in
bindings documentation.
Fixes: 212e496935 ("dt-bindings: mtd: Add YAML schemas for the generic NAND options")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Validating the examples against the schema have a few errors:
arm,gic.example.dt.yaml: 'ranges' does not match any of the regexes: '^v2m@[0-9a-f]+$', 'pinctrl-[0-9]+'
arm,gic.example.dt.yaml: #address-cells:0:0: 2 is not one of [0, 1]
arm,gic.example.dt.yaml: #size-cells:0:0: 1 was expected
'ranges' is valid, but missing from the schema, so add it. The reg
addresses and sizes don't match the schema requirements and the example
template. We could just override the example template to use 64-bit
addresses, but there's not really any value showing that in the example.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Following commit 31af04cd60 ("arm64: dts: Remove inconsistent use of
'arm,armv8' compatible string"), clean up these binding examples in case
anyone is tempted to copy them.
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
These files were converted to json-schema, but the references weren't
renamed.
Fixes: 66ed144f14 ("dt-bindings: interrupt-controller: Convert ARM GIC to json-schema")
(and other similar commits)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In order to have $ref's to schema files within the kernel, we need to
pass the base path of bindings to the schema validation tools.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: devicetree@vger.kernel.org
Cc: linux-kbuild@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
For IP blocks that are generated from the public, open-source
sifive-blocks repository, describe the version numbering policy
that its maintainers intend to use, upon request from Rob
Herring <robh@kernel.org>.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Megan Wachs <megan@sifive.com>
Cc: Wesley Terpstra <wesley@sifive.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the max8660 binding to DT schema format using json-schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the gpio-regulator binding to DT schema format using
json-schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the common regulator binding to DT schema format. Note that all
the properties with standard unit suffixes have type checks already, so
only a description is necessary.
As fixed-regulator has already been converted, update the references in
it. Otherwise, keep regulator.txt with a reference to the schema to
avoid a bunch of treewide updates. regulator.txt can be removed when all
the regulator bindings are converted.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the spi-gpio binding to DT schema format.
Cc: Mark Brown <broonie@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch the DT binding to a YAML schema to enable the DT validation.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
