The XWAY family allows to extend the number of gpios by using shift
registers or latches. This patch adds the 2 drivers needed for this. The
extended gpios are output only.
[ralf@linux-mips.org: Fixed ltq_stp_probe section() attributes.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2258/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Lantiq family of SoCs have a EBU (External Bus Unit). This patch adds
the driver that allows us to use the EBU as a PCI controller. In order for
PCI to work the EBU is set to endianess swap all the data. In addition we
need to make use of SWAP_IO_SPACE for device->host DMA to work.
The clock of the PCI works in several modes (internal/external). If this
is not configured correctly the SoC will hang.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the Lantiq XWAY family of Mips24KEc SoCs.
* Danube (PSB50702)
* Twinpass (PSB4000)
* AR9 (PSB50802)
* Amazon SE (PSB5061)
The Amazon SE is a lightweight SoC and has no PCI as well as a different
clock. We split the code out into seperate files to handle this.
The GPIO pins on the SoCs are multi function and there are several bits
we can use to configure the pins. To be as compatible as possible to
GPIOLIB we add a function
int lq_gpio_request(unsigned int pin, unsigned int alt0,
unsigned int alt1, unsigned int dir, const char *name);
which lets you configure the 2 "alternate function" bits. This way drivers like
PCI can make use of GPIOLIB without a cubersome wrapper.
The PLL code inside arch/mips/lantiq/xway/clk-xway.c is voodoo to me. It was
taken from a 2.4.20 source tree and was never really changed by me since then.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2249/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add initial support for Mips based SoCs made by Lantiq. This series will add
support for the XWAY family.
The series allows booting a minimal system using a initramfs or NOR. Missing
drivers and support for Amazon and GPON family will be provided in a later
series.
[Ralf: Remove some cargo cult programming and fixed formatting.]
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2252/
Patchwork: https://patchwork.linux-mips.org/patch/2371/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds pci/pci-xlr.c to support for XLR PCI/PCI-X interface and XLS PCIe
interface.
Update irq.c to ack PCI interrupts, use irq handler data to do the
PCI/PCIe bus ack.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable XLR CPU support, SMP, initramfs based root filesystem etc.
[ralf@linux-mips.org: shrink the defconfig file through make savedefconfig.]
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add NLM_XLR_BOARD, CPU_XLR and other config options
Makefile updates, mostly based on r4k
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* include/asm/netlogic added with files common for all Netlogic processors
(common with XLP which will be added later)
* include/asm/netlogic/xlr for XLR/XLS chip specific files
* netlogic/xlr for XLR/XLS platform files
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2334/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CPU_XLR case added to mm/tlbex.c
CPU_XLR case added to mm/c-r4k.c for PINDEX attribute
Feature overrides for XLR cpu.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2333/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add Netlogic Microsystems company ID and processor IDs for XLR
and XLS processors for CPU probe. Add CPU_XLR to cpu_type_enum.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2367/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 'size' variable contains the correct register size for both AR7
and Titan, but we never used it to ioremap the correct register size.
This problem only shows up on Titan.
[ralf@linux-mips.org: Fixed the fix. The original patch as in patchwork
recognizes the problem correctly then fails to fix it ...]
Reported-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2380/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This fixes:
alchemy/xxs1500/init.c: In function 'prom_init':
alchemy/xxs1500/init.c:57:17: error: ignoring return value of 'kstrtoul', declared with attribute warn_unused_result
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2340/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PAGE_SIZE >= 64kb (1 << 16) is too big to be the immediate of the
addiu/daddiu instruction, so, use addu/daddu instruction instead.
The following compiling error is fixed:
AS arch/mips/power/hibernate.o
arch/mips/power/hibernate.S: Assembler messages:
arch/mips/power/hibernate.S:38: Error: expression out of range
make[2]: *** [arch/mips/power/hibernate.o] Error 1
make[1]: *** [arch/mips/power] Error 2
Reported-by: Roman Mamedov <rm@romanrm.ru>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2313/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code for supporting one-shot mode for the clockevent is already there,
only the feature flag was not set. Setting the one-shot flag allows the
kernel to run in tickless mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/jz4740/dma.o
arch/mips/jz4740/dma.c: In function 'jz4740_dma_chan_irq':
arch/mips/jz4740/dma.c:245:11: error: variable 'status' set but not used [-Werro
r=unused-but-set-variable]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
HOSTCC arch/mips/boot/compressed/calc_vmlinuz_load_addr
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c: In function 'main':
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:35:2: warning: format '%llx' expects type 'long long unsigned int *', but argument 3 has type 'uint64_t *'
arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:54:2: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'uint64_t'
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/alchemy/devboards/db1x00/board_setup.o
arch/mips/alchemy/devboards/db1x00/board_setup.c: In function 'board_setup':
arch/mips/alchemy/devboards/db1x00/board_setup.c:130:6: error: variable 'pin_func' set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip27/ip27-hubio.o
arch/mips/sgi-ip27/ip27-hubio.c: In function 'hub_pio_map':
arch/mips/sgi-ip27/ip27-hubio.c:32:20: error: variable 'junk' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip27/ip27-hubio.o
arch/mips/sgi-ip27/ip27-hubio.c: In function 'hub_pio_map':
arch/mips/sgi-ip27/ip27-hubio.c:32:20: error: variable 'junk' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of making each Octeon specific option depend on
CPU_CAVIUM_OCTEON, gate the body of the entire file with
CPU_CAVIUM_OCTEON. With this change, CAVIUM_OCTEON_SPECIFIC_OPTIONS
becomes useless, so get rid of it as well.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2091/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Octeon doesn't use IRQ_CPU, so don't select it.
IRQ_CPU_OCTEON is a completely unused symbol, remove it completely.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2086/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/loongson/common/env.o
arch/mips/loongson/common/env.c: In function 'prom_init_env':
arch/mips/loongson/common/env.c:50:12: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
arch/mips/loongson/common/env.c:51:12: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
arch/mips/loongson/common/env.c:52:12: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
arch/mips/loongson/common/env.c:53:12: error: variable 'ret' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/jazz/jazzdma.o
arch/mips/jazz/jazzdma.c: In function 'vdma_remap':
arch/mips/jazz/jazzdma.c:214:20: error: variable 'npages' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sni/time.o
arch/mips/sni/time.c: In function 'dosample':
arch/mips/sni/time.c:98:19: error: variable 'lsb' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mti-malta/malta-int.o
arch/mips/mti-malta/malta-int.c: In function 'mips_pcibios_iack':
arch/mips/mti-malta/malta-int.c:59:6: error: variable 'dummy' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mti-malta/malta-init.o
arch/mips/mti-malta/malta-init.c: In function 'prom_init':
arch/mips/mti-malta/malta-init.c:196:6: error: variable 'result' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip22/ip22-platform.o
arch/mips/sgi-ip22/ip22-platform.c: In function 'sgiseeq_devinit':
arch/mips/sgi-ip22/ip22-platform.c:135:15: error: variable 'tmp' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
While at it rename the variable to pbdma for readability; there is a
local variable tmp of different type being used in two nested blocks.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/sgi-ip22/ip22-time.o
arch/mips/sgi-ip22/ip22-time.c: In function 'dosample':
arch/mips/sgi-ip22/ip22-time.c:35:10: error: variable 'lsb' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mm/tlbex.o
arch/mips/mm/tlbex.c: In function 'build_r4000_tlb_refill_handler':
arch/mips/mm/tlbex.c:1155:22: error: variable 'vmalloc_mode' set but not used [-Werror=unused-but-set-variable]
arch/mips/mm/tlbex.c:1154:28: error: variable 'htlb_info' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/mm/c-r4k.o
arch/mips/mm/c-r4k.c: In function 'probe_scache':
arch/mips/mm/c-r4k.c:1078:6: error: variable 'tmp' set but not used [-Werror=unused-but-set-variable]
cc1: all warnings being treated as errors
Older GCC versions didn't warn about the unused variable tmp because it was
getting initialized.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code is abusing the uasm interface by passing jump target
addresses with high bits set. Mask the addresses to avoid annoying
messages at boot time.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1922/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
