Because the following patch will rewrite the content between normal IO
and resync IO. So we used a parameter to indicate whether raid is in freeze
array.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When raid5 recovery hits a fresh badblock, this badblock will flagged as unack
badblock until md_update_sb() is called.
But md_stop will take reconfig lock which means raid5d can't call
md_update_sb() in md_check_recovery(), the badblock will always
be unack, so raid5d thread enters an infinite loop and md_stop_write()
can never stop sync_thread. This causes deadlock.
To solve this, when STOP_ARRAY ioctl is issued and sync_thread is
running, we need set md->recovery FROZEN and INTR flags and wait for
sync_thread to stop before we (re)take reconfig lock.
This requires that raid5 reshape_request notices MD_RECOVERY_INTR
(which it probably should have noticed anyway) and stops waiting for a
metadata update in that case.
Reported-by: Jianpeng Ma <majianpeng@gmail.com>
Reported-by: Bian Yu <bianyu@kedacom.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We currently use kthread_should_stop() in various places in the
sync/reshape code to abort early.
However some places set MD_RECOVERY_INTR but don't immediately call
md_reap_sync_thread() (and we will shortly get another one).
When this happens we are relying on md_check_recovery() to reap the
thread and that only happen when it finishes normally.
So MD_RECOVERY_INTR must lead to a normal finish without the
kthread_should_stop() test.
So replace all relevant tests, and be more careful when the thread is
interrupted not to acknowledge that latest step in a reshape as it may
not be fully committed yet.
Also add a test on MD_RECOVERY_INTR in the 'is_mddev_idle' loop
so we don't wait have to wait for the speed to drop before we can abort.
Signed-off-by: NeilBrown <neilb@suse.de>
Sometimes we need to lock and mddev and cannot cope with
failure due to interrupt.
In these cases we should use mutex_lock, not mutex_lock_interruptible.
Signed-off-by: NeilBrown <neilb@suse.de>
Because of block layer merge, one bio fails will cause other bios
which belongs to the same request fails, so raid5_end_read_request
will record all these bios as badblocks.
If retry request with R5_ReadNoMerge flag to avoid bios merge,
badblocks can only record sector which is bad exactly.
test:
hdparm --yes-i-know-what-i-am-doing --make-bad-sector 300000 /dev/sdb
mdadm -C /dev/md0 -l5 -n3 /dev/sd[bcd] --assume-clean
mdadm /dev/md0 -f /dev/sdd
mdadm /dev/md0 -r /dev/sdd
mdadm --zero-superblock /dev/sdd
mdadm /dev/md0 -a /dev/sdd
1. Without this patch:
cat /sys/block/md0/md/rd*/bad_blocks
299776 256
299776 256
2. With this patch:
cat /sys/block/md0/md/rd*/bad_blocks
300000 8
300000 8
Signed-off-by: Bian Yu <bianyu@kedacom.com>
Signed-off-by: NeilBrown <neilb@suse.de>
track empty inactive list count, so md_raid5_congested() can use it to make
decision.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The dm-delay target uses a shared workqueue for multiple instances. This
can cause deadlock if two or more dm-delay targets are stacked on the top
of each other.
This patch changes dm-delay to use a per-instance workqueue.
Cc: stable@vger.kernel.org # 2.6.22+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Pull second round of block driver updates from Jens Axboe:
"As mentioned in the original pull request, the bcache bits were pulled
because of their dependency on the immutable bio vecs. Kent re-did
this part and resubmitted it, so here's the 2nd round of (mostly)
driver updates for 3.13. It contains:
- The bcache work from Kent.
- Conversion of virtio-blk to blk-mq. This removes the bio and request
path, and substitutes with the blk-mq path instead. The end result
almost 200 deleted lines. Patch is acked by Asias and Christoph, who
both did a bunch of testing.
- A removal of bootmem.h include from Grygorii Strashko, part of a
larger series of his killing the dependency on that header file.
- Removal of __cpuinit from blk-mq from Paul Gortmaker"
* 'for-linus' of git://git.kernel.dk/linux-block: (56 commits)
virtio_blk: blk-mq support
blk-mq: remove newly added instances of __cpuinit
bcache: defensively handle format strings
bcache: Bypass torture test
bcache: Delete some slower inline asm
bcache: Use ida for bcache block dev minor
bcache: Fix sysfs splat on shutdown with flash only devs
bcache: Better full stripe scanning
bcache: Have btree_split() insert into parent directly
bcache: Move spinlock into struct time_stats
bcache: Kill sequential_merge option
bcache: Kill bch_next_recurse_key()
bcache: Avoid deadlocking in garbage collection
bcache: Incremental gc
bcache: Add make_btree_freeing_key()
bcache: Add btree_node_write_sync()
bcache: PRECEDING_KEY()
bcache: bch_(btree|extent)_ptr_invalid()
bcache: Don't bother with bucket refcount for btree node allocations
bcache: Debug code improvements
...
Make this useful helper available for other users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_active_stripe() is the last place we have lock contention. It has two
paths. One is stripe isn't found and new stripe is allocated, the other is
stripe is found.
The first path basically calls __find_stripe and init_stripe. It accesses
conf->generation, conf->previous_raid_disks, conf->raid_disks,
conf->prev_chunk_sectors, conf->chunk_sectors, conf->max_degraded,
conf->prev_algo, conf->algorithm, the stripe_hashtbl and inactive_list. Except
stripe_hashtbl and inactive_list, other fields are changed very rarely.
With this patch, we split inactive_list and add new hash locks. Each free
stripe belongs to a specific inactive list. Which inactive list is determined
by stripe's lock_hash. Note, even a stripe hasn't a sector assigned, it has a
lock_hash assigned. Stripe's inactive list is protected by a hash lock, which
is determined by it's lock_hash too. The lock_hash is derivied from current
stripe_hashtbl hash, which guarantees any stripe_hashtbl list will be assigned
to a specific lock_hash, so we can use new hash lock to protect stripe_hashtbl
list too. The goal of the new hash locks introduced is we can only use the new
locks in the first path of get_active_stripe(). Since we have several hash
locks, lock contention is relieved significantly.
The first path of get_active_stripe() accesses other fields, since they are
changed rarely, changing them now need take conf->device_lock and all hash
locks. For a slow path, this isn't a problem.
If we need lock device_lock and hash lock, we always lock hash lock first. The
tricky part is release_stripe and friends. We need take device_lock first.
Neil's suggestion is we put inactive stripes to a temporary list and readd it
to inactive_list after device_lock is released. In this way, we add stripes to
temporary list with device_lock hold and remove stripes from the list with hash
lock hold. So we don't allow concurrent access to the temporary list, which
means we need allocate temporary list for all participants of release_stripe.
One downside is free stripes are maintained in their inactive list, they can't
across between the lists. By default, we have total 256 stripes and 8 lists, so
each list will have 32 stripes. It's possible one list has free stripe but
other list hasn't. The chance should be rare because stripes allocation are
even distributed. And we can always allocate more stripes for cache, several
mega bytes memory isn't a big deal.
This completely removes the lock contention of the first path of
get_active_stripe(). It slows down the second code path a little bit though
because we now need takes two locks, but since the hash lock isn't contended,
the overhead should be quite small (several atomic instructions). The second
path of get_active_stripe() (basically sequential write or big request size
randwrite) still has lock contentions.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If raid5_start_reshape errors out, we need to reset all the fields
that were updated (not just some), and need to use the seq_counter
to ensure make_request() doesn't use an inconsitent state.
Signed-off-by: NeilBrown <neilb@suse.de>
The various ->run routines of md personalities assume that the 'queue'
has been initialised by the blk_set_stacking_limits() call in
md_alloc().
However when the level is changed (by level_store()) the ->run routine
for the new level is called for an array which has already had the
stacking limits modified. This can result in incorrect final
settings.
So call blk_set_stacking_limits() before ->run in level_store().
A specific consequence of this bug is that it causes
discard_granularity to be set incorrectly when reshaping a RAID4 to a
RAID0.
This is suitable for any -stable kernel since 3.3 in which
blk_set_stacking_limits() was introduced.
Cc: stable@vger.kernel.org (3.3+)
Reported-and-tested-by: "Baldysiak, Pawel" <pawel.baldysiak@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When release_stripe() is called in grow_one_stripe(), the
mddev->thread is null. So it will omit one wakeup this thread to
release stripe.
For this condition, use slow_path to release stripe.
Bug was introduced in 3.12
Cc: stable@vger.kernel.org (3.12+)
Fixes: 773ca82fa1
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Improve reliability of buffer allocations for dm messages with a small
number of arguments, a couple path group initialization fixes for dm
multipath, a fix for resizing a dm array, various fixes and
optimizations for dm cache, a fix for device mapper's Kconfig menu
indentation.
Features added include:
- dm crypt support for activating legacy CBC TrueCrypt containers
(useful for forensics of these old TCRYPT containers)
- reduced dm-cache memory requirements for each block in the cache
- basic support for shrinking a dm-cache's cache (fast) device
- most notably, dm-cache support for managing cache coherency when
deploying dm-cache with sophisticated origin volumes (that support
hardware snapshots and/or clustering): these changes come in the form
of a new passthrough operation mode and a cache block invalidation
interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSgt+QAAoJEMUj8QotnQNapcEIALC6U1rmw08PRMSanqg4/aVu
pTahzPtai9jXchQV6q5XsglJryrhD9MoNqrZgHd2drdnmEKTKfVX+/iCXGiE4hQ5
I5QUZf5myEXSd60pCgZwNam+VHMuAuSPQW6LWqRTJjDLHixGF+AoHZGxkEsYgj6M
p686OOpga1nmT2w072xLIh9z2tsv/tm+UN7GSbyklM+/1ItcXxq+/J8rsuth7IqT
k0I60jexq+Q3OaYuJY7vxhdE7PhBCw1fGmtuCcjekqsSVpAdCgDz3FFOEZmyXcUs
YLFE3GcclYQpIPjNjVGTLDFHdoIMWdKiibs/ScBUtegqxWvqP7c87YFhbL+VHDM=
=lLxo
-----END PGP SIGNATURE-----
Merge tag 'dm-3.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper changes from Mike Snitzer:
"A set of device-mapper changes for 3.13.
Improve reliability of buffer allocations for dm messages with a small
number of arguments, a couple path group initialization fixes for dm
multipath, a fix for resizing a dm array, various fixes and
optimizations for dm cache, a fix for device mapper's Kconfig menu
indentation.
Features added include:
- dm crypt support for activating legacy CBC TrueCrypt containers
(useful for forensics of these old TCRYPT containers)
- reduced dm-cache memory requirements for each block in the cache
- basic support for shrinking a dm-cache's cache (fast) device
- most notably, dm-cache support for managing cache coherency when
deploying dm-cache with sophisticated origin volumes (that support
hardware snapshots and/or clustering): these changes come in the
form of a new passthrough operation mode and a cache block
invalidation interface"
* tag 'dm-3.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (32 commits)
dm cache: resolve small nits and improve Documentation
dm cache: add cache block invalidation support
dm cache: add remove_cblock method to policy interface
dm cache policy mq: reduce memory requirements
dm cache metadata: check the metadata version when reading the superblock
dm cache: add passthrough mode
dm cache: cache shrinking support
dm cache: promotion optimisation for writes
dm cache: be much more aggressive about promoting writes to discarded blocks
dm cache policy mq: implement writeback_work() and mq_{set,clear}_dirty()
dm cache: optimize commit_if_needed
dm space map disk: optimise sm_disk_dec_block
MAINTAINERS: add reference to device-mapper's linux-dm.git tree
dm: fix Kconfig menu indentation
dm: allow remove to be deferred
dm table: print error on preresume failure
dm crypt: add TCW IV mode for old CBC TCRYPT containers
dm crypt: properly handle extra key string in initialization
dm cache: log error message if dm_kcopyd_copy() fails
dm cache: use cell_defer() boolean argument consistently
...
Pull block IO core updates from Jens Axboe:
"This is the pull request for the core changes in the block layer for
3.13. It contains:
- The new blk-mq request interface.
This is a new and more scalable queueing model that marries the
best part of the request based interface we currently have (which
is fully featured, but scales poorly) and the bio based "interface"
which the new drivers for high IOPS devices end up using because
it's much faster than the request based one.
The bio interface has no block layer support, since it taps into
the stack much earlier. This means that drivers end up having to
implement a lot of functionality on their own, like tagging,
timeout handling, requeue, etc. The blk-mq interface provides all
these. Some drivers even provide a switch to select bio or rq and
has code to handle both, since things like merging only works in
the rq model and hence is faster for some workloads. This is a
huge mess. Conversion of these drivers nets us a substantial code
reduction. Initial results on converting SCSI to this model even
shows an 8x improvement on single queue devices. So while the
model was intended to work on the newer multiqueue devices, it has
substantial improvements for "classic" hardware as well. This code
has gone through extensive testing and development, it's now ready
to go. A pull request is coming to convert virtio-blk to this
model will be will be coming as well, with more drivers scheduled
for 3.14 conversion.
- Two blktrace fixes from Jan and Chen Gang.
- A plug merge fix from Alireza Haghdoost.
- Conversion of __get_cpu_var() from Christoph Lameter.
- Fix for sector_div() with 64-bit divider from Geert Uytterhoeven.
- A fix for a race between request completion and the timeout
handling from Jeff Moyer. This is what caused the merge conflict
with blk-mq/core, in case you are looking at that.
- A dm stacking fix from Mike Snitzer.
- A code consolidation fix and duplicated code removal from Kent
Overstreet.
- A handful of block bug fixes from Mikulas Patocka, fixing a loop
crash and memory corruption on blk cg.
- Elevator switch bug fix from Tomoki Sekiyama.
A heads-up that I had to rebase this branch. Initially the immutable
bio_vecs had been queued up for inclusion, but a week later, it became
clear that it wasn't fully cooked yet. So the decision was made to
pull this out and postpone it until 3.14. It was a straight forward
rebase, just pruning out the immutable series and the later fixes of
problems with it. The rest of the patches applied directly and no
further changes were made"
* 'for-3.13/core' of git://git.kernel.dk/linux-block: (31 commits)
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: Do not call sector_div() with a 64-bit divisor
kernel: trace: blktrace: remove redundent memcpy() in compat_blk_trace_setup()
block: Consolidate duplicated bio_trim() implementations
block: Use rw_copy_check_uvector()
block: Enable sysfs nomerge control for I/O requests in the plug list
block: properly stack underlying max_segment_size to DM device
elevator: acquire q->sysfs_lock in elevator_change()
elevator: Fix a race in elevator switching and md device initialization
block: Replace __get_cpu_var uses
bdi: test bdi_init failure
block: fix a probe argument to blk_register_region
loop: fix crash if blk_alloc_queue fails
blk-core: Fix memory corruption if blkcg_init_queue fails
block: fix race between request completion and timeout handling
blktrace: Send BLK_TN_PROCESS events to all running traces
blk-mq: don't disallow request merges for req->special being set
blk-mq: mq plug list breakage
blk-mq: fix for flush deadlock
...
Document passthrough mode, cache shrinking, and cache invalidation.
Also, use strcasecmp() and hlist_unhashed().
Reported-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cache block invalidation is removing an entry from the cache without
writing it back. Cache blocks can be invalidated via the
'invalidate_cblocks' message, which takes an arbitrary number of cblock
ranges:
invalidate_cblocks [<cblock>|<cblock begin>-<cblock end>]*
E.g.
dmsetup message my_cache 0 invalidate_cblocks 2345 3456-4567 5678-6789
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Implement policy_remove_cblock() and add remove_cblock method to the mq
policy. These methods will be used by the following cache block
invalidation patch which adds the 'invalidate_cblocks' message to the
cache core.
Also, update some comments in dm-cache-policy.h
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rather than storing the cblock in each cache entry, we allocate all
entries in an array and infer the cblock from the entry position.
Saves 4 bytes of memory per cache block. In addition, this gives us an
easy way of looking up cache entries by cblock.
We no longer need to keep an explicit bitset to track which cblocks
have been allocated. And no searching is needed to find free cblocks.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Need to check the version to verify on-disk metadata is supported.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
"Passthrough" is a dm-cache operating mode (like writethrough or
writeback) which is intended to be used when the cache contents are not
known to be coherent with the origin device. It behaves as follows:
* All reads are served from the origin device (all reads miss the cache)
* All writes are forwarded to the origin device; additionally, write
hits cause cache block invalidates
This mode decouples cache coherency checks from cache device creation,
largely to avoid having to perform coherency checks while booting. Boot
scripts can create cache devices in passthrough mode and put them into
service (mount cached filesystems, for example) without having to worry
about coherency. Coherency that exists is maintained, although the
cache will gradually cool as writes take place.
Later, applications can perform coherency checks, the nature of which
will depend on the type of the underlying storage. If coherency can be
verified, the cache device can be transitioned to writethrough or
writeback mode while still warm; otherwise, the cache contents can be
discarded prior to transitioning to the desired operating mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Morgan Mears <Morgan.Mears@netapp.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Allow a cache to shrink if the blocks being removed from the cache are
not dirty.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Just to be safe, call the error reporting function with "%s" to avoid
any possible future format string leak.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Never saw a profile of bset_search_tree() where it wasn't bottlenecked
on memory until I got my new Haswell machine, but when I tried it there
it was suddenly burning 20% of the cpu in the inner loop on shrd...
Turns out, the version of shrd that takes 64 bit operands has a 9 cycle
latency. hah.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The flow control in btree_insert_node() was... fragile... before,
this'll use more stack (but since our btrees are never more than depth
1, that shouldn't matter) and it should be significantly clearer and
less fragile.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Big garbage collection rewrite; now, garbage collection uses the same
mechanisms as used elsewhere for inserting/updating btree node pointers,
instead of rewriting interior btree nodes in place.
This makes the code significantly cleaner and less fragile, and means we
can now make garbage collection incremental - it doesn't have to hold a
write lock on the root of the btree for the entire duration of garbage
collection.
This means that there's less of a latency hit for doing garbage
collection, which means we can gc more frequently (and do a better job
of reclaiming from the cache), and we can coalesce across more btree
nodes (improving our space efficiency).
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Trying to treat btree pointers and leaf node pointers the same way was a
mistake - going to start being more explicit about the type of
key/pointer we're dealing with. This is the first part of that
refactoring; this patch shouldn't change any actual behaviour.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The bucket refcount (dropped with bkey_put()) is only needed to prevent
the newly allocated bucket from being garbage collected until we've
added a pointer to it somewhere. But for btree node allocations, the
fact that we have btree nodes locked is enough to guard against races
with garbage collection.
Eventually the per bucket refcount is going to be replaced with
something specific to bch_alloc_sectors().
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Couple changes:
* Consolidate bch_check_keys() and bch_check_key_order(), and move the
checks that only check_key_order() could do to bch_btree_iter_next().
* Get rid of CONFIG_BCACHE_EDEBUG - now, all that code is compiled in
when CONFIG_BCACHE_DEBUG is enabled, and there's now a sysfs file to
flip on the EDEBUG checks at runtime.
* Dropped an old not terribly useful check in rw_unlock(), and
refactored/improved a some of the other debug code.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Previously, bch_ptr_bad() could return false when there was a pointer to
a nonexistant device... it only filtered out keys with PTR_CHECK_DEV
pointers.
This behaviour was intended for multiple cache device support; for that,
just because the device for one of the pointers has gone away doesn't
mean we want to filter out the rest of the pointers.
But we don't yet explicitly filter/check individual pointers, so without
that this behaviour was wrong - a corrupt bkey with a bad device pointer
could cause us to deref a bad pointer. Doh.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Now, the on disk data structures are in a header that can be exported to
userspace - and having them all centralized is nice too.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
With all the recent refactoring around struct btree op struct search has
gotten rather large.
But we can now easily break it up in a different way - we break out
struct btree_insert_op which is for inserting data into the cache, and
that's now what the copying gc code uses - struct search is now specific
to request.c
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Last of the btree_map() conversions. Main visible effect is
bch_btree_insert() is no longer taking a struct btree_op as an argument
anymore - there's no fancy state machine stuff going on, it's just a
normal function.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
When we convert bch_btree_insert() to bch_btree_map_leaf_nodes(), we
won't be passing struct btree_op to bch_btree_insert() anymore - so we
need a different way of returning whether there was a collision (really,
a replace collision).
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This is prep work for converting bch_btree_insert to
bch_btree_map_leaf_nodes() - we have to convert all its arguments to
actual arguments. Bunch of churn, but should be straightforward.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
There was some looping in submit_partial_cache_hit() and
submit_partial_cache_hit() that isn't needed anymore - originally, we
wouldn't necessarily process the full hit or miss all at once because
when splitting the bio, we took into account the restrictions of the
device we were sending it to.
But, device bio size restrictions are now handled elsewhere, with a
wrapper around generic_make_request() - so that looping has been
unnecessary for awhile now and we can now do quite a bit of cleanup.
And if we trim the key we're reading from to match the subset we're
actually reading, we don't have to explicitly calculate bi_sector
anymore. Neat.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This is a fairly straightforward conversion, mostly reshuffling -
op->lookup_done goes away, replaced by MAP_DONE/MAP_CONTINUE. And the
code for handling cache hits and misses wasn't really btree code, so it
gets moved to request.c.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
With the new btree_map() functions, we don't need to export the stuff
needed for traversing the btree anymore.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Lots of stuff has been open coding its own btree traversal - which is
generally pretty simple code, but there are a few subtleties.
This adds new new functions, bch_btree_map_nodes() and
bch_btree_map_keys(), which do the traversal for you. Everything that's
open coding btree traversal now (with the exception of garbage
collection) is slowly going to be converted to these two functions;
being able to write other code at a higher level of abstraction is a
big improvement w.r.t. overall code quality.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This simplifies the writeback flow control quite a bit - previously, it
was conceptually two coroutines, refill_dirty() and read_dirty(). This
makes the code quite a bit more straightforward.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
We needed a dedicated rescuer workqueue for gc anyways... and gc was
conceptually a dedicated thread, just one that wasn't running all the
time. Switch it to a dedicated thread to make the code a bit more
straightforward.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
At one point we did do fancy asynchronous waiting stuff with
bucket_wait, but that's all gone (and bucket_wait is used a lot less
than it used to be). So use the standard primitives.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Slowly working on pruning struct btree_op - the aim is for it to only
contain things that are actually necessary for traversing the btree.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Making things less asynchronous that don't need to be - bch_journal()
only has to block when the journal or journal entry is full, which is
emphatically not a fast path. So make it a normal function that just
returns when it finishes, to make the code and control flow easier to
follow.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Try to improve some of the naming a bit to be more consistent, and also
improve the flow of control in request_write() a bit.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Some refactoring - better to explicitly pass stuff around instead of
having it all in the "big bag of state", struct btree_op. Going to prune
struct btree_op quite a bit over time.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This was the main point of all this refactoring - now,
btree_insert_check_key() won't fail just because the leaf node happened
to be full.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
We'll often end up with a list of adjacent keys to insert -
because bch_data_insert() may have to fragment the data it writes.
Originally, to simplify things and avoid having to deal with corner
cases bch_btree_insert() would pass keys from this list one at a time to
btree_insert_recurse() - mainly because the list of keys might span leaf
nodes, so it was easier this way.
With the btree_insert_node() refactoring, it's now a lot easier to just
pass down the whole list and have btree_insert_recurse() iterate over
leaf nodes until it's done.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The flow of control in the old btree insertion code was rather -
backwards; we'd recurse down the btree (in btree_insert_recurse()), and
then if we needed to split the keys to be inserted into the parent node
would be effectively returned up to btree_insert_recurse(), which would
notice there was more work to do and finish the insertion.
The main problem with this was that the full logic for btree insertion
could only be used by calling btree_insert_recurse; if you'd gotten to a
btree leaf some other way and had a key to insert, if it turned out that
node needed to be split you were SOL.
This inverts the flow of control so btree_insert_node() does _full_
btree insertion, including splitting - and takes a (leaf) btree node to
insert into as a parameter.
This means we can now _correctly_ handle cache misses - for cache
misses, we need to insert a fake "check" key into the btree when we
discover we have a cache miss - while we still have the btree locked.
Previously, if the btree node was full inserting a cache miss would just
fail.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
This is prep work for the reworked btree insertion code.
The way we set b->parent is ugly and hacky... the problem is, when
btree_split() or garbage collection splits or rewrites a btree node, the
parent changes for all its (potentially already cached) children.
I may change this later and add some code to look through the btree node
cache and find all our cached child nodes and change the parent pointer
then...
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Checking i->seq was redundant, because since ages ago we always
initialize the new bset when advancing b->written
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Originally I got this right... except that the divides didn't use
do_div(), which broke 32 bit kernels. When I went to fix that, I forgot
that the raid stripe size usually isn't a power of two... doh
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
The old asynchronous discard code was really a relic from when all the
allocation code was asynchronous - now that allocation runs out of a
dedicated thread there's no point in keeping around all that complicated
machinery.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
bch_keybuf_del() takes a spinlock that can't be taken in interrupt context -
whoops. Fortunately, this code isn't enabled by default (you have to toggle a
sysfs thing).
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Dirty data accounting wasn't quite right - firstly, we were adding the key we're
inserting after it could have merged with another dirty key already in the
btree, and secondly we could sometimes pass the wrong offset to
bcache_dev_sectors_dirty_add() for dirty data we were overwriting - which is
important when tracking dirty data by stripe.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.10
If a write block triggers promotion and covers a whole block we can
avoid a copy.
Introduce dm_{hook,unhook}_bio to simplify saving and restoring bio
fields (bi_private is now used by overwrite). Switch writethrough
support over to using these helpers too.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Previously these promotions only got priority if there were unused cache
blocks. Now we give them priority if there are any clean blocks in the
cache.
The fio_soak_test in the device-mapper-test-suite now gives uniform
performance across subvolumes (~16 seconds).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There are now two multiqueues for in cache blocks. A clean one and a
dirty one.
writeback_work comes from the dirty one. Demotions come from the clean
one.
There are two benefits:
- Performance improvement, since demoting a clean block is a noop.
- The cache cleans itself when io load is light.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Check commit_requested flag _before_ calling
dm_cache_changed_this_transaction() superfluously.
Also, be sure to set last_commit_jiffies _after_ dm_cache_commit()
completes.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Don't waste time spotting blocks that have been allocated and then freed
in the same transaction.
The extra lookup is expensive, and I don't think it really gives us much.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The option DM_LOG_USERSPACE is sub-option of DM_MIRROR, so place it
right after DM_MIRROR. Doing so fixes various other Device mapper
targets/features to be properly nested under "Device mapper support".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch allows the removal of an open device to be deferred until
it is closed. (Previously such a removal attempt would fail.)
The deferred remove functionality is enabled by setting the flag
DM_DEFERRED_REMOVE in the ioctl structure on DM_DEV_REMOVE or
DM_REMOVE_ALL ioctl.
On return from DM_DEV_REMOVE, the flag DM_DEFERRED_REMOVE indicates if
the device was removed immediately or flagged to be removed on close -
if the flag is clear, the device was removed.
On return from DM_DEV_STATUS and other ioctls, the flag
DM_DEFERRED_REMOVE is set if the device is scheduled to be removed on
closure.
A device that is scheduled to be deleted can be revived using the
message "@cancel_deferred_remove". This message clears the
DMF_DEFERRED_REMOVE flag so that the device won't be deleted on close.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If preresume fails it is worth logging an error given that a device is
left suspended due to the failure.
This change was motivated by local preresume error logging that was
added to the cache target ("preresume failed"). Elevating this
target-agnostic context for the where the target-specific error occurred
relative to the DM core's callouts makes sense.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
dm-crypt can already activate TCRYPT (TrueCrypt compatible) containers
in LRW or XTS block encryption mode.
TCRYPT containers prior to version 4.1 use CBC mode with some additional
tweaks, this patch adds support for these containers.
This new mode is implemented using special IV generator named TCW
(TrueCrypt IV with whitening). TCW IV only supports containers that are
encrypted with one cipher (Tested with AES, Twofish, Serpent, CAST5 and
TripleDES).
While this mode is legacy and is known to be vulnerable to some
watermarking attacks (e.g. revealing of hidden disk existence) it can
still be useful to activate old containers without using 3rd party
software or for independent forensic analysis of such containers.
(Both the userspace and kernel code is an independent implementation
based on the format documentation and it completely avoids use of
original source code.)
The TCW IV generator uses two additional keys: Kw (whitening seed, size
is always 16 bytes - TCW_WHITENING_SIZE) and Kiv (IV seed, size is
always the IV size of the selected cipher). These keys are concatenated
at the end of the main encryption key provided in mapping table.
While whitening is completely independent from IV, it is implemented
inside IV generator for simplification.
The whitening value is always 16 bytes long and is calculated per sector
from provided Kw as initial seed, xored with sector number and mixed
with CRC32 algorithm. Resulting value is xored with ciphertext sector
content.
IV is calculated from the provided Kiv as initial IV seed and xored with
sector number.
Detailed calculation can be found in the Truecrypt documentation for
version < 4.1 and will also be described on dm-crypt site, see:
http://code.google.com/p/cryptsetup/wiki/DMCrypt
The experimental support for activation of these containers is already
present in git devel brach of cryptsetup.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some encryption modes use extra keys (e.g. loopAES has IV seed) which
are not used in block cipher initialization but are part of key string
in table constructor.
This patch adds an additional field which describes the length of the
extra key(s) and substracts it before real key encryption setting.
The key_size always includes the size, in bytes, of the key provided
in mapping table.
The key_parts describes how many parts (usually keys) are contained in
the whole key buffer. And key_extra_size contains size in bytes of
additional keys part (this number of bytes must be subtracted because it
is processed by the IV generator).
| K1 | K2 | .... | K64 | Kiv |
|----------- key_size ----------------- |
| |-key_extra_size-|
| [64 keys] | [1 key] | => key_parts = 65
Example where key string contains main key K, whitening key
Kw and IV seed Kiv:
| K | Kiv | Kw |
|--------------- key_size --------------|
| |-----key_extra_size------|
| [1 key] | [1 key] | [1 key] | => key_parts = 3
Because key_extra_size is calculated during IV mode setting, key
initialization is moved after this step.
For now, this change has no effect to supported modes (thanks to ilog2
rounding) but it is required by the following patch.
Also, fix a sparse warning in crypt_iv_lmk_one().
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A migration failure should be logged (albeit limited).
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix a few cell_defer() calls that weren't passing a bool.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Return -EINVAL when the specified cache policy is unknown rather than
returning -ENOMEM.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Rename takeout_queue to concat_queue.
Fix a harmless bug in mq policies pop() function. Currently pop()
always succeeds, with up coming changes this wont be the case.
Fix typo in comment above pre_cache_to_cache prototype.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Make the quiescing flag an atomic_t and stop protecting it with a spin
lock.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The code that was trying to do this was inadequate. The postsuspend
method (in ioctl context), needs to wait for the worker thread to
acknowledge the request to quiesce. Otherwise the migration count may
drop to zero temporarily before the worker thread realises we're
quiescing. In this case the target will be taken down, but the worker
thread may have issued a new migration, which will cause an oops when
it completes.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
Previously only origin bios could trigger ticks, which meant if all
the io was destined for the cache no ticks were generated. If no ticks
are generated then multiple hits, and movements in general, are
attributed to the same tick.
Only a stop gap fix, we need a better solution.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It is safe to use a mutex in mq_residency() at this point since it is
only called from ioctl context. But future-proof mq_residency() by
using might_sleep() to catch new contexts that cannot sleep.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Someone cut and pasted md's md_trim_bio() into xen-blkfront.c. Come on,
we should know better than this.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they all
get slowly migrated over to the safe versions of the attribute groups
(removing userspace races with the creation of the sysfs files.) Also
in here are some kobject updates, devres expansions, and the first round
of Tejun's sysfs reworking to enable it to be used by other subsystems
as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xAMACgkQMUfUDdst+yk1kQCfcHXhfnrvFZ5J/mDP509IzhNS
ddEAoLEWoivtBppNsgrWqXpD1vi4UMsE
=JmVW
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they
all get slowly migrated over to the safe versions of the attribute
groups (removing userspace races with the creation of the sysfs
files.) Also in here are some kobject updates, devres expansions, and
the first round of Tejun's sysfs reworking to enable it to be used by
other subsystems as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (83 commits)
sysfs: rename sysfs_assoc_lock and explain what it's about
sysfs: use generic_file_llseek() for sysfs_file_operations
sysfs: return correct error code on unimplemented mmap()
mdio_bus: convert bus code to use dev_groups
device: Make dev_WARN/dev_WARN_ONCE print device as well as driver name
sysfs: separate out dup filename warning into a separate function
sysfs: move sysfs_hash_and_remove() to fs/sysfs/dir.c
sysfs: remove unused sysfs_get_dentry() prototype
sysfs: honor bin_attr.attr.ignore_lockdep
sysfs: merge sysfs_elem_bin_attr into sysfs_elem_attr
devres: restore zeroing behavior of devres_alloc()
sysfs: fix sysfs_write_file for bin file
input: gameport: convert bus code to use dev_groups
input: serio: remove bus usage of dev_attrs
input: serio: use DEVICE_ATTR_RO()
i2o: convert bus code to use dev_groups
memstick: convert bus code to use dev_groups
tifm: convert bus code to use dev_groups
virtio: convert bus code to use dev_groups
ipack: convert bus code to use dev_groups
...
