Yakui pointed out that we don't properly no-op the ACPI button routines
if the button driver isn't built in. This will cause problems if ACPI
is disabled, so provide stub functions in that case.
Reported-by: ykzhao <yakui.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some drivers need to know when a lid event occurs and get the current
status. This can be useful for when a platform firmware clobbers some
hardware state at lid time, and a driver needs to restore things when
the lid is opened again.
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The wakeup.prepared flag is used for marking devices that have the
wake-up power already enabled, so that the wake-up power is not
enabled twice in a row for the same device. This assumes, however,
that device wake-up power will only be enabled once, while the device
is being prepared for a system-wide sleep transition, and the second
attempt is made by acpi_enable_wakeup_device_prep().
With the upcoming PCI wake-up rework this assumption will not hold
any more for PCI bridges and the root bridge whose wake-up power
may be enabled as a result of wake-up enable propagation from other
devices (eg. add-on devices that are not associated with any GPEs).
Thus, there may be many attempts to enable wake-up power on a PCI
bridge or the root bridge during a system power state transition
and it's better to replace wakeup.prepared with a reference counter.
Reviewed-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We can simplify ACPI drivers if we can tell whether a handle is an
ACPI PCI root or not.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Version 20090903.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linux/ACPI core files using internal.h all PREFIX "ACPI: ",
however, not all ACPI drivers use/want it -- and they
should not have to #undef PREFIX to define their own.
Add GPL commment to internal.h while we are there.
This does not change any actual console output,
asside from a whitespace fix.
Signed-off-by: Len Brown <len.brown@intel.com>
Version 20090730.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Problem with the name of one of the subtables.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Eliminate duplicated code in disassembler.
Shorten identifiers that were too long.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add IVRS,MSCT,UEFI,WAET,WDAT.
Updated several existing tables for ACPI 4.0-related changes.
Added document references for all tables not defined in ACPI spec.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split out the non-acpi-defined ACPI tables into the existing
(but empty) actbl2.h file. Preparation for new ACPI 4.0 tables.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
http://bugzilla.kernel.org/show_bug.cgi?id=13620
If the dynamic region is created and added to resource list over and over again,
it has the potential to be a memory leak by growing the list every time.
This patch fixes the memory leak, as below
1) add a new field "count" to struct acpi_res_list.
When inserting, if the region(addr, len) is already in the resource
list, we just increase "count", otherwise, the region is inserted
with count=1.
When deleting, the "count" is decreased, if it's decreased to 0,
the region is deleted from the resource list.
With "count", the region with same address and length can only be
inserted to the resource list once, so prevent potential memory leak.
2) add a new function acpi_os_invalidate_address, which is called when
region is deleted.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version number.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
FACS: new flag and new OspmFlags field.
SRAT: x2APIC - add ClockDomain field to descriptor #2
Includes header and disassembler support.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Handler was never invoked. Now invoked if/when host node is deleted.
Data object was not automatically deleted when host node was deleted.
Interface to handler had an unused parameter, removed it.
ACPICA BZ 778.
http://acpica.org/bugzilla/show_bug.cgi?id=778
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds support for IPMI which is similar to SMBus and uses a bi-directional data buffer.
ACPICA BZ 773.
http://acpica.org/bugzilla/show_bug.cgi?id=773
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Needed by drivers for new ACPi tables. Internal versions of
these functions still use 32-bit max transfers, in order to
minimize disruption and stack use for the standard ACPI registers
(FADT-based).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some were defined twice, causes a warning with gcc
-Wredundant-decls.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If the BIOS reports an invalid throttling state (which seems to be
fairly common after system boot), a reset is done to state T0.
Because of a check in acpi_processor_get_throttling_ptc(), the reset
never actually gets executed, which results in the error reoccurring
on every access of for example /proc/acpi/processor/CPU0/throttling.
Add a 'force' option to acpi_processor_set_throttling() to ensure
the reset really takes effect.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13389
This patch, together with the next one, fixes a regression introduced in
2.6.30, listed on the regression list. They have been available for 2.5
months now in bugzilla, but have not been picked up, despite various
reminders and without any reason given.
Google shows that numerous people are hitting this issue. The issue is in
itself relatively minor, but the bug in the code is clear.
The patches have been in all my kernels and today testing has shown that
throttling works correctly with the patches applied when the system
overheats (http://bugzilla.kernel.org/show_bug.cgi?id=13918#c14).
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No drivers use the .stop method, so remove it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Sometimes both acpi video and i915 driver are compiled as modules.
And there exists the strict dependency between the two drivers.
The acpi video bus will be unloaded in course of unloading the i915 driver.
If we unload the acpi video driver, then the kernel oops will be triggered.
Add the reference count to avoid unloading the ACPI video bus twice.
The reference count should be checked before unregistering the acpi video bus.
If the reference count is already zero, it won't unregister it again.
And after the acpi video bus is already unregistered, the reference count
will be set to zero.
http://bugzilla.kernel.org/show_bug.cgi?id=13396
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
arch_acpi_processor_cleanup_pdc() in x86 and ia64 results in memory allocated
for _PDC objects that is never freed and will cause memory leak in case of
physical CPU remove and add. Patch fixes the memory leak by freeing the
objects soon after _PDC is evaluated.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
System notify events (0x00-0x7f) are common across all device types
and should be handled in Linux/ACPI, not in drivers. However, some
BIOSes use system notify events in device-specific ways that require
the driver to be involved.
This patch adds a ACPI_DRIVER_ALL_NOTIFY_EVENTS driver flag. When a
driver sets this flag and supplies a .notify method, Linux/ACPI calls
the .notify method for ALL notify events on the device, not just the
device-specific (0x80-0xff) events.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_get_pci_dev() is (hopefully) better, and all callers have been
converted, so let's get rid of this duplicated functionality.
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_get_pci_dev() is better, and all callers have been converted, so
eliminate acpi_get_pci_id().
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There is no need to pass a segment/bus tuple to this API, as the callsite
always has a struct pci_bus. We can derive segment/bus from the
struct pci_bus, so let's take this opportunit to simplify the API and
make life easier for the callers.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A PCI domain cannot change as you descend down subordinate buses, which
makes the 'segment' argument to acpi_pci_irq_add_prt() useless.
Change the interface to take a struct pci_bus *, from whence we can derive
the bus number and segment. Reducing the number of arguments makes life
simpler for callers.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that we can dynamically convert an ACPI CA handle to a
struct pci_dev at runtime, there's no need to statically bind
them during boot.
acpi_pci_bind/unbind are vastly simplified, and are only used
to evaluate _PRT methods on P2P bridges and non-bridge children.
This patch also changes the time-space tradeoff ever so slightly.
Looking up the ACPI-PCI binding is never in the performance path, and by
eliminating this caching, we save 24 bytes for each _ADR device in the
ACPI namespace.
This patch lays further groundwork to eventually eliminate
the acpi_driver_ops.bind callback.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Convert an ACPI CA handle to a struct pci_dev.
Performing this lookup dynamically allows us to get rid of the
ACPI-PCI binding code, which:
- eliminates struct acpi_device vs struct pci_dev lifetime issues
- lays more groundwork for eliminating .start from acpi_device_ops
and thus simplifying ACPI drivers
- whacks out a lot of code
This change lays the groundwork for eliminating much of pci_bind.c.
Although pci_root.c may not be the most logical place for this
change, putting it here saves us from having to export acpi_pci_find_root.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Returns whether an ACPI CA node is a PCI root bridge or not.
This API is generically useful, and shouldn't just be a hotplug function.
The implementation becomes much simpler as well.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_pci_root_add() explicitly assigns device->ops.bind, and later
calls acpi_pci_bind_root(), which also does the same thing.
We don't need to repeat ourselves; removing the explicit assignment
allows us to make acpi_pci_bind() static.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously [5], now [8].
sprintf(acpi_device_bid(device), "CPU%X", cpu_id)
now looks better on systems with more than 0xFF processors.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI0007 _HID used for processor "Device" objects in the namespace
is not needed outside the processor driver, so move it there. Also, the
#define is only used once, so just remove it and hard-code "ACPI0007".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI_PROCESSOR_OBJECT_HID is a synthetic _HID that Linux generates
for "Processor" definitions. Unlike "Device" definitions, "Processor"
definitions do not have a _HID in the namespace, so we generate a
fake _HID. By convention, all these fake _HIDs begin with "LNX".
This does change the user-visible _HID for "Processor" objects --
previously, we used "ACPI_CPU" and this changes that to "LNXCPU",
which starts with "LNX" as do all the other made-up _HIDs. This
change is visible in processor filenames and "hid" files under
/sys/devices/LNXSYSTM:00/.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version number.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This interface enables the override or creation of a single
control method. Useful to repair a bug or install a missing method.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Version 20090422.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Merge the OSL with the actual file used by Linux, so that the
file does not require patching when integrated with Linux. General
cleanup and some restructuring.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed unnecessary masking. For the 64-bit macros, removed
the structure overlay. Fixes aliasing warnings seen with gcc 4+
compilers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Mostly for acpiexec, one in the core subsystem.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Moved the module name and line number to the end of the message.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix up error path leak in i915_cmdbuffer
drm/i915: fix unpaired i915 device mutex on entervt failure.
drm/i915: add support for G41 chipset
drm/i915: Enable ASLE if present
drm/i915: Unregister ACPI video driver when exiting
drm/i915: Register ACPI video even when not modesetting
drm/i915: fix transition to I915_TILING_NONE
drm/i915: Don't let an oops get triggered from irq_emit without dma init.
drm/i915: allow tiled front buffers on 965+
Linux-2.6.29 deleted the legacy ACPI idle handler, leaving
the CPU_IDLE handler, which does not track bus master activity.
So delete the unused bm_activity field -- it is confusing to
print an always zero value.
This patch could break programs that parse
/proc/acpi/processor/*/power, since it deletes this
line from that file:
bus master activity: 00000000
http://bugzilla.kernel.org/show_bug.cgi?id=13145
is not fixed by this patch, but provoked this patch.
Signed-off-by: Len Brown <len.brown@intel.com>
The i915 DRM triggers registration of the ACPI video driver on load. It
should unregister it at unload in order to avoid generating backtraces on
being reloaded.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.
There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).
Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for ACPI device driver .notify() methods. If
such a method is present, Linux/ACPI installs a handler for device
notifications (but not for system notifications such as Bus Check,
Device Check, etc). When a device notification occurs, Linux/ACPI
passes it on to the driver's .notify() method.
In most cases, this removes the need for drivers to install their own
handlers for device-specific notifications.
For fixed hardware devices like some power and sleep buttons, there's
no notification value because there's no control method to execute a
Notify opcode. When a fixed hardware device generates an event, we
handle it the same as a regular device notification, except we send
a ACPI_FIXED_HARDWARE_EVENT value. This is outside the normal 0x0-0xff
range used by Notify opcodes.
Several drivers install their own handlers for system Bus Check and
Device Check notifications so they can support hot-plug. This patch
doesn't affect that usage.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Intel graphics hardware that implements the ACPI IGD OpRegion spec
requires that the list of display devices be populated before any ACPI
video methods are called. Detect when this is the case and defer
registration until the opregion code calls it. Fixes crashes on HP
laptops.
http://bugzilla.kernel.org/show_bug.cgi?id=11259
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Len Brown <len.brown@intel.com>
In acpi_bus_ops, only the acpi_op_add and acpi_op_start flags are used,
so remove all the rest.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
No drivers use the .lock and .scan methods, and the Linux/ACPI
code doesn't even provide a way to invoke them, so remove them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Version 20090320.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This interface is no longer necessary. Requests should be validated
on a per-field basis, not on the entire operation region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add and deploy constants for the PM status/enable/control
registers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Version 20090220.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename acpi_get_register and acpi_set_register to clarify the
purpose of these functions. New names are acpi_read_bit_register
and acpi_write_bit_register.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed locking for reads from the ACPI bit registers in PM1
Status, Enable, Control, and PM2 Control. The lock is not required
when reading the single-bit registers. The acpi_get_register_unlocked
function is no longer needed and has been removed. This will
improve performance for reads on these registers. ACPICA BZ 760.
http://www.acpica.org/bugzilla/show_bug.cgi?id=760
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function is only needed on 64-bit host operating systems.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This type is the same as TYPE_A. Removed this and all related
instances. Renamed SLEEP_TYPE_A to simply SLEEP_TYPE.
ACPICA BZ 754.
http://www.acpica.org/bugzilla/show_bug.cgi?id=754
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now return AE_BAD_PARAMETER if the input register pointer is
null, and AE_BAD_ADDRESS if the register has an address of zero.
Previously, these cases simply returned AE_OK. For optional
registers such as PM1B status/enable/control, the caller should
check for a valid register address before calling. ACPICA BZ 748.
http://www.acpica.org/bugzilla/show_bug.cgi?id=748
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version to 20090123.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add new flags in the Boot Architecture flags field. Update comments
for all FADT flags. Add FADT version when each flag was defined.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, the table override mechanism was implemented for the
DSDT only. Now, any table in the RSDT/XSDT can be replaced by
the host OS. (including the DSDT).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A number of things that shouldn't be exposed outside the ACPI core
were declared in include/acpi/acpi_drivers.h, where anybody can
see them. This patch moves those declarations to a new "internal.h"
inside drivers/acpi.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
to prevent wrongly overwriting fixmap that still want to use.
ACPI used to rely on low mappings being all linearly mapped and
grew a habit: it never really unmapped certain kinds of tables
after use.
This can cause problems - for example the hypothetical case
when some spurious access still references it.
v2: remove prev_map and prev_size in __apci_map_table
v3: let acpi_os_unmap_memory() call early_iounmap too, so remove extral calling to
early_acpi_os_unmap_memory
v4: fix typo in one acpi_get_table_with_size calling
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Bit 11 in intel PDC definitions is meant for OS capability to handle
hardware coordination of P-states. In Linux we have always supported
hwardware coordination of P-states. Just let the BIOSes know that we
support it, by setting this bit.
Some BIOSes use this bit to choose between hardware or software coordination
and without this change below, BIOSes switch to software coordination, which
is not very optimal in terms of power consumption and extra wakeups from idle.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Make the comment for ACPI_FADT_S4_RTC_WAKE match the ACPI spec;
that bit has nothing to do with status bits.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
drivers/acpi/pci_irq.c
Note that this merge disables
e1d3a90846
pci, acpi: reroute PCI interrupt to legacy boot interrupt equivalent
Signed-off-by: Len Brown <len.brown@intel.com>
On some boxes there exist both RSDT and XSDT table. But unfortunately
sometimes there exists the following error when XSDT table is used:
a. 32/64X address mismatch
b. The 32/64X FACS address mismatch
In such case the boot option of "acpi=rsdt" is provided so that
RSDT is tried instead of XSDT table when the system can't work well.
http://bugzilla.kernel.org/show_bug.cgi?id=8246
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
cc:Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Impact: Reduce memory usage, use new API.
This is part of an effort to reduce structure sizes for machines
configured with large NR_CPUS. cpumask_t gets replaced by
cpumask_var_t, which is either struct cpumask[1] (small NR_CPUS) or
struct cpumask * (large NR_CPUS).
(Changes to powernow-k* by <travis>.)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This returns the FADT support to the original behavior, which is
to use default register widths. However, now check each register
definition and report a warning if it differs from the default.
This is a first step to moving away from the default widths,
rather than outright believing the widths in all FADTs for all
machines, considered rather dangerous until more data is obtained.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
1) Update the register lengths for the PM1 event blocks. The
length must be divided by two in order to use these to access
the status registers.
2) Add run-time option to use default register lengths to override a
faulty FADT.
3) Add warning message if any of the X64 address structures contain a length
that does not match the legacy length earlier in the FADT.
4) Move all FADT warning messages into the ValidateFadt function.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Used to specify whether the OSL mutex interfaces should be used,
or binary semaphores instead.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Eliminate extraneous "zero length subtable" messages.
Fix subtable output for ERST, MCFG, EINJ tables.
Implement all subtables for HEST.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi.h now includes only the "public" acpica headers. All other
acpica headers are "private" and should not be included by acpica
users. One new file, accommon.h is used to include the commonly
used private headers for acpica code generation. Future plans
are to move all private headers to a new subdirectory.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Uses the FADT-defined reset register and reset value. Checks the
FADT flags for the reset register supported bit. Supports reset
register in memory or I/O space, but not in PCI config space
since the host has the information to do it.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Changed the acpi_hw_low_level_read and acpi_hw_low_level_write functions to
the public acpi_read and acpi_write to allow direct access to
ACPI registers. Removed the "width" parameter since the width
can be obtained from the input GAS structure. Updated the FADT
initialization to setup the GAS structures with the proper
widths. Some widths are still hardcoded because many FADTs have
incorrect register lengths.
Signed-off-by: Bob Moore <robert.moore@intel.com
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added acpi_disable_all_gpes and acpi_enable_all_runtime_gpes for
public use.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function maps an input GPE index to a GPE block device. Also
Added acpi_current_gpe_count to track the current number of GPEs
that are being managed by the ACPICA core (both FADT-based GPEs
and the GPEs contained in GPE block devices.)
Modify drivers/acpi/system.c to use these 2 new interfaces
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
return_ACPI_STATUS is an internal acpica function, replace it with return.
acpi_gbl_permanent_mmap moved from acglobal.h to acpixf.h for external use
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
use ACPI_ALLOCATE_BUFFER to remove the allocations
within acpi_pci_bind(), acpi_pci_unbind() and acpi_pci_bind_root().
While there, delete some unnecessary param inits from those routines.
Delete concept of ACPI_PATHNAME_MAX, since this was the last use.
Signed-off-by: Len Brown <len.brown@intel.com>
Merge the code that validates control method argument counts into
the predefined validation module. Eliminates possible multiple
warnings for incorrect counts.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For predefined methods (such as _BIF), add automatic conversion for
objects that are required to be a String, but a Buffer was found
instead. This can happen when reading string battery data from
an operation region, because it used to be difficult to convert
the data from buffer to string from within the ASL. Linux BZ 11822.
http://bugzilla.kernel.org/show_bug.cgi?id=11822
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use a global pointer instead of using AcpiGetTableByIndex for
each FACS access. This simplifies the code for the Global Lock
and the Firmware Waking Vector(s).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a loop counter to force exit from AML While loops if the
count becomes too large. This can occur in poorly written AML
when the hardware does not respond within a while loop and the
loop does not implement a timeout. The maximum loop count is
configurable. A new exception code is returned when a loop is
broken, AE_AML_INFINITE_LOOP. Bob Moore, Alexey Starikovskiy.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split AcpiSetFirmwareWakingVector into two: one for the 32-bit
vector, another for the 64-bit vector. This is required because the
host OS must setup the wake much differently for each vector (real
vs. protected mode, etc.) and the interface should not be deciding
which vector to use. Also eliminate the GetFirmwareWakingVector
interface, as it served no purpose (only the firmware reads the
vector, OS only writes the vector.) ACPICA BZ 731.
http://www.acpica.org/bugzilla/show_bug.cgi?id=731
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
New compiler is pickier than older versions.
Joerg Sonnenberger. From ACPICA BZ 732.
http://www.acpica.org/bugzilla/show_bug.cgi?id=732
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI interpreter usually runs with irqs enabled.
However, during suspend/resume it runs with
irqs disabled to evaluate _GTS/_BFS, as well as
by irqrouter_resume() which evaluates _CRS, _PRS, _SRS.
http://bugzilla.kernel.org/show_bug.cgi?id=12252
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_early_init() was changed to over-write the cmdline param,
making it really inconvenient to set debug flags at boot-time.
Also,
This sets the default level to "info", which is what all the ACPI
drivers use. So to enable messages from drivers, you only have to
supply the "layer" (a.k.a. "component"). For non-"info" ACPI core
and ACPI interpreter messages, you have to supply both level and
layer masks, as before.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A generic work-around from ACPICA is in the queue,
but since Linux has a work-around in its battery
driver, we can disable this warning now.
Allow _BIF method to return an Package with Buffer elements
http://bugzilla.kernel.org/show_bug.cgi?id=11822
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This can happen if the _WAK method returns nothing (as per ACPI
1.0) but does return an integer if the implicit return mechanism
is enabled. This is the only method that has this problem,
since it is also defined to return a package of two integers
(ACPI 1.0b+). In all other cases, if a method returns an object
when one was not expected, no warning is issued.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Disabling gpe might interfere with gpe detection/handling,
thus producing "interrupt not handled" errors.
Ironically, disabling of GPE from interrupt context is already
under spinlock, so only userspace needs to start using it.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This is a reimplemention of commit
0119509c4f
from Matthew Garrett <mjg59@srcf.ucam.org>
This patch got removed because of a regression: ThinkPads with a
Intel graphics card and an Integrated Graphics Device BIOS implementation
stopped working.
In fact, they only worked because the ACPI device of the discrete, the
wrong one, got used (via int10). So ACPI functions were poking on the wrong
hardware used which is a sever bug.
The next patch provides support for above ThinkPads to be able to
switch brightness via the legacy thinkpad_acpi driver and automatically
detect when to use it.
Original commit message from Matthew Garrett:
Vendors often ship machines with a choice of integrated or discrete
graphics, and use the same DSDT for both. As a result, the ACPI video
module will locate devices that may not exist on this specific platform.
Attempt to determine whether the device exists or not, and abort the
device creation if it doesn't.
http://bugzilla.kernel.org/show_bug.cgi?id=9614
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
/sys/module/acpi/parameters/debug_layers used to contain only the
debug layers defined by the ACPI CA. This patch adds the additional
layer definitions for ACPI drivers.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some of the component definitions that were previous scattered around
the drivers conflict with each other. That doesn't hurt anything
except that setting one bit in the debug_layer mask would turn on
debugging in two different modules. This patch fixes the conflicts.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move all the component definitions for drivers to a single shared place,
include/acpi/acpi_drivers.h.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Declaring processors in ACPI namespace can be done using either a
"Processor" definition or a "Device" definition (see section 8.4 -
Declaring Processors; "Advanced Configuration and Power Interface
Specification", Revision 3.0b). Currently the two processor
declaration types are conflated.
This patch disambiguates the processor declaration's definition type
enabling subsequent code to behave uniquely based explicitly on the
declaration's type.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_EC. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Per section 6.5.4 of the ACPI 3.0b specification,
OSPM must make Embedded Controller operation regions, accessed
via the Embedded Controllers described in ECDT, available before
executing any control method.
The ECDT table is optional, but if it is present, the above text
means that the EC it describes is a required part of the ACPI
subsystem, so CONFIG_ACPI_EC=n wouldn't make sense.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove CONFIG_ACPI_POWER. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
The interfaces under CONFIG_ACPI_POWER (acpi_device_sleep_wake(),
acpi_power_transition(), etc) are called unconditionally from the
ACPI core, so we already depend on it always being present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce a new flag showing whether the event has an event handler/method.
For all the GPEs and Fixed Events,
1. ACPI_EVENT_FLAG_HANDLE is cleared, it's an "invalid" ACPI event.
2. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_DISABLE are set,
it's "disabled".
3. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_ENABLE are set,
it's "enabled".
4. Both ACPI_EVENT_FLAG_HANDLE and ACPI_EVENT_FLAG_WAKE_ENABLE are set,
it's "wake_enabled".
Among other things, this prevents incorrect reporting of ACPI events
as being "invalid" when it's really just (temporarily) "disabled".
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version to 20080926.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Validates predefined ACPI objects that appear in the namespace,
at the time they are evaluated. The argument count and the type of
the returned object are validated. The purpose of this validation
is to detect problems with the BIOS-exposed predefined ACPI objects
before the results are returned to the ACPI-related drivers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed the ACPI_BITREG_WAKE_ENABLE definition and entry in the
global register table. This bit does not exist and is unused.
http://www.acpica.org/bugzilla/show_bug.cgi?id=442
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version to 20080829.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix some sloppiness in the Reference object. No longer use AML
opcodes to differentiate the types, introduce new reference
Class. Cleanup the debug output code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
1) Add new field for use by DdbHandle (Value)
2) Use ACPI_CAST_INDIRECT_PTR to eliminate strict type warnings
3) Cleanup debug output
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed 10 exception codes (and corresponding name strings)
that were obsolete for various reasons.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add ACPI_NAMESPACE_NODE to the ACPI_OPERAND_OBJECT in order to
simplify code that accepts both of these objects. A common type
field is used to differentiate them.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed ACPI_DB_WARN and ACPI_DB_ERROR. These debug levels were
made obsolete by the ACPI_WARNING and ACPI_ERROR/ACPI_EXCEPTION
interfaces. Also added ACPI_DB_EVENTS to correspond with the
existing ACPI_LV_EVENTS.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Support for the x2APIC. There are 2 new subtables for the MADT and
one new subtable for the SRAT. Includes disassembler and acpisrc
support. Data from the Intel 64 Architecture x2APIC Specification,
June 2008.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Created for improved error messages.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version to 20080701.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also update the debugger so that the correct number of arguments is
passed to the method. Prevents a warning message from the debugger.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed unused macros. Ensure that multiple parameters always have a space
after a comma. Cleanup some comments.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Return status from acpi_ut_init_globals. This is used by both
the kernel subsystem and the utilities such as iASL compiler.
The function could possibly fail when the caches are initialized.
Yang Yi.
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The "minimal" descriptors such as EndTag are calculated as 12
bytes long, but the actual length in the internal descriptor is
16 because of the round-up to 8 on 64-bit build.
http://www.acpica.org/bugzilla/show_bug.cgi?id=728
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Maybe the incorrect power state is returned on the bogus bios, which
is different with the real power state. For example: the bios returns D0
state and the real power state is D3. OS expects to set the device to D0
state. In such case if OS uses the power state returned by the BIOS and
checks the device power state very strictly in power transition, the device
can't be transited to the correct power state.
So the boot option of "acpi.power_nocheck=1" is added to avoid checking
the device power in the course of device power transition.
http://bugzilla.kernel.org/show_bug.cgi?id=8049http://bugzilla.kernel.org/show_bug.cgi?id=11000
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As of version 2.0, ACPI can return 64-bit integers. The current
acpi_evaluate_integer only supports 64-bit integers on 64-bit platforms.
Change the argument to take a pointer to an acpi_integer so we support
64-bit integers on all platforms.
lenb: replaced use of "acpi_integer" with "unsigned long long"
lenb: fixed bug in acpi_thermal_trips_update()
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
when there is no ECDT table and no _INI object for EC device, it will be
enabled before scanning ACPI device. But it is too late after the following
the commit is merged.
>commit 7752d5cfe3
> Author: Robert Hancock <hancockr@shaw.ca>
> Date: Fri Feb 15 01:27:20 2008 -0800
>x86: validate against acpi motherboard resources
After the above commit is merged, OS will check whether MCFG area is
reserved in ACPI motherboard resources by calling the function of
acpi_get_devices when there exists MCFG table. In the acpi_get_devices the _STA
object will be evaluated to check the status of the ACPI device. On some broken
BIOS the MYEC object of EC device is initialized as one, which indicates that
EC operation region is already accessible before enabling EC device.So on these
broken BIOS the EC operation region will be accessed in course of evaluating
the _STA object before enabling EC device, which causes that OS will print the
following warning messages:
>ACPI Error (evregion-0315): No handler for Region [EC__] (ffff88007f8145e8)
[EmbeddedControl] [20080609]
>ACPI Error (exfldio-0290): Region EmbeddedControl(3) has no handler [20080321]
>ACPI Error (psparse-0530): Method parse/execution failed [\_SB_.PCI0.SBRG.
EC__.BAT1._STA] (Node ffff81013fc17a00), AE_NOT_EXIST
>ACPI Error (uteval-0233): Method execution failed [\_SB_.PCI0.SBRG.EC__.BAT1.
_STA] (Node ffff81013fc17a00), AE_NOT_EXIST
Although the above warning message is harmless, it looks confusing.
So it is necessary to enable EC device as early as possible.Maybe it is
appropriate to enable it immediately after ACPI full initialization.
http://bugzilla.kernel.org/show_bug.cgi?id=11255http://bugzilla.kernel.org/show_bug.cgi?id=11374http://bugzilla.kernel.org/show_bug.cgi?id=11660
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Catch attempts to use of acpi_driver_data on pointers of wrong type.
akpm: rewritten to use proper C typechecking and remove the
"function"-used-as-lvalue thing.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
dock's uevent reported itself, not ata. It might be difficult to find an
ata device just according to a dock. This patch introduces docking ops
for each device in a dock. when docking, dock driver can send device
specific uevent. This should help dock station too (not just bay)
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The hotplug notification handler and drivers' notification handler all
run in one workqueue. Before hotplug removes an acpi device, the
device driver's notification handler is already be recorded to run just
after global notification handler. After hotplug notification handler
runs, acpica will notice a NULL notification handler and crash.
So now we run run hotplug in another workqueue and wait
for all acpi notication handlers finish.
This was found in battery hotplug, but actually all
hotplug can be affected.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The battery driver already registers notification handler.
To avoid registering notification handler again,
introduce a notifier chain in global system notifier handler
and use it in dock driver.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add error check after all calls to acpi_ns_get_pathname_length.
Add status return from acpi_ns_build_external_path and check after
all calls. Add parameter validation to acpi_ut_initialize_buffer.
Reported by and initial patch by Ingo Molnar.
http://lkml.org/lkml/2008/7/21/176
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
The ACPI FADT table includes an ASPM control bit. If the bit is set, do
not enable ASPM since it may indicate that the platform doesn't actually
support the feature.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
Allow users to enable/disable/clear a specific & valid GPE/Fixed Event
in user space.
This is useful for debugging, especially for some
interrupt storm issues.
All wakeup GPEs are disabled and they can not be enabled at runtime,
and we mark them as invalid.
All GPEs that don't have a _Lxx/_Exx method are marked as invalid.
All Fixed Events that don't have an event handler are marked as invalid
and they can't be enabled until an event handler is registered.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ling Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Eliminated unnecessary operands; eliminated use of negative index
in loop. Operands now displayed in correct order, not backwards.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Now supports the 2007 intel Virtualization Technology for Directed
I/O specification.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Synchronized tables with current specifications.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Update version to 20080514
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Mostly MODULE_NAME and printf format strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
No longer needed; replaced mostly with u32, but also acpi_size
where a type that changes 32/64 bit on 32/64-bit platforms is
required.
v2: Fix a cast of a 32-bit int to a pointer in ACPI to avoid a compiler warning.
from David Howells
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Added NULL fields to the exception string arrays to eliminate
the -1 subtraction on the SubStatus field.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Changed ACPI_MODULE_NAME and ACPI_FUNCTION_NAME to use arrays of
strings instead of pointers to static strings. Jan Beulich and
Bob Moore.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Fixes problem where the new method argument count validation mechanism
will enter an infinite loop when a GPE method is dispatched.
Problem fixed be removing the obsolete code that passes GPE block
information to the notify handler via the control method parameter pointer.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Error if too few arguments, warning if too many. This applies
only to external programmatic control method execution, not
method-to-method calls within the AML.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Reorder the mutex names to match the preceding #defines
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Implemented another change for the GPE disable. We now perform a
read-change-write of the enable register instead of simply writing out the
cached enable mask. This will prevent inadvertent enabling of GPEs if a rogue
GPE is received during initialization (before GPE handlers are installed.)
http://bugzilla.kernel.org/show_bug.cgi?id=6217
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Change processors from an array sized by NR_CPUS to a per_cpu variable.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
So that one of the several config option permutations will build again.
Tested-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Introduce function acpi_pm_device_sleep_wake() for enabling and
disabling the system wake-up capability of devices that are power
manageable by ACPI.
* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
subsystems to check if ACPI is able to enable the system wake-up
capability of given device.
* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().
* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
for the ACPI 'driver' make it use acpi_bus_can_wakeup().
* Move the PME# handlig code out of pci_enable_wake() and split it
into two functions, pci_pme_capable() and pci_pme_active(),
allowing the caller to check if given device is capable of
generating PME# from given power state and to enable/disable the
device's PME# functionality, respectively.
* Modify pci_enable_wake() to use the new ACPI callbacks and the new
PME#-related functions.
* Drop the generic .platform_enable_wakeup() callback that is not
used any more.
* Introduce device_set_wakeup_capable() that will set the
power.can_wakeup flag of given device.
* Rework PCI device PM initialization so that, if given device is
capable of generating wake-up events, either natively through the
PME# mechanism, or with the help of the platform, its
power.can_wakeup flag is set and its power.should_wakeup flag is
unset as appropriate.
* Make ACPI set the power.can_wakeup flag for devices found to be
wake-up capable by it.
* Make the ACPI wake-up code enable/disable GPEs for devices that
have the wakeup.flags.prepared flag set (which means that their
wake-up power has been enabled).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce additional flag 'prepared' in struct acpi_device_wakeup_flags
and use it to prevent devices from being enable/disabled do wake up the
system multiple times in a row (this does not happen currently, but will
be possible after some of the following patches).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The currect ACPI code attempts to execute _PSW at three different
places and in one of them only it tries to execute _DSW before _PSW,
which is inconsistent with the other two cases.
Move the execution of _DSW and _PSW into a separate function called
acpi_device_sleep_wake() and call it wherever appropriate instead of
executing _DSW and/or _PSW directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce function acpi_bus_power_manageable() allowing other
(dependent) subsystems to check if ACPI is able to power manage given
device. This may be useful, for example, for PCI device power
management.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch adds a proper prototype for acpi_processor_tstate_has_changed()
in include/acpi/processor.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version to 20080321.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented several changes for Notify handling: Added support
for new Notify values (ACPI 2.0+) and improved the Notify debug
output. Notify on PowerResource objects is no longer allowed,
as per the ACPI specification.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed problem where NULL package elements were not returned to
the AcpiEvaluateObject interface correctly. Instead of returning a
NULL ACPI_OBJECT package element, the element was simply ignored,
potentially causing a buffer overflow and/or confusing the caller
who expected a fixed number of elements.
http://bugzilla.kernel.org/show_bug.cgi?id=10132
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Update ACPICA version to 20080213.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem where resource descriptor size optimization
could cause a problem when a _CRS resource template is passed
to a _SRS method. The _SRS resource template must use the same
descriptors (with the same size) as returned from _CRS. This
change affects the following resource descriptors: IRQ/IRQNoFlags
and StartDependendentFn/StartDependentFnNoPri.
http://bugzilla.kernel.org/show_bug.cgi?id=9487
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented full disassembler support for the following new ACPI
tables: BERT, EINJ, and ERST. Partial disassembler support for
the complicated HEST table. These tables support the Windows
Hardware Error Architecture (WHEA).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a regression introduced in version 20071114. The ACPI_HIDWORD
macro was inadvertently changed to return a 16-bit value instead of
a 32-bit value, truncating the upper Dword of a 64-bit value. This
macro is only used to display debug output, so no incorrect
calculations were made.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version to 20080123.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with the disassembler where invalid ACPI tables
could cause faults or infinite loops.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Implemented header file support for new ACPI tables - BERT, ERST,
EINJ, HEST, IBFT, UEFI, WDAT. Disassembler support is forthcoming.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Update version to 20071219.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This enables forward references and full operand resolution for
the three string arguments. Similar to OperationRegion deferred
argument execution.)
http://www.acpica.org/bugzilla/show_bug.cgi?id=430
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
